Search Documents

The ore, as sent to the sulphide mill, is a mixture, in varying proportions, of oxidized ore from above the 450-ft. level and sulphide ore from above and below (to date mainly from above) that level. The oxidized ore consists essentially of quartz, with varying amounts of kaolin and clayey material which passes into the slime and, in excess, creates a serious problem in settling. Pyrite may be present in small amounts. The gold is free and extremely fine.The ore, classed as sulphide, consists of pyritic material in a quartz gangue. The sulphides have been exposed to weathering, leaching by descending solutions and attack by ascending gases and actual burning. The alteration products occur in widely varying proportions and this variation adds to the difficulties in settling and control of grinding and flotation.Copper Minerals.-Chalcopyrite is the principal copperbearing mineral with smaller and varying amounts of covellite, which is sometimes associated with chalcocite, both these minerals being apparently of secondary origin.Examination of tailing by Dr. Stillwell has revealed all stages between clean chalcopyrite, chalcopyrite tinged with covellite, covellite with residual cores of chalcopyrite and clean covellite.The chalcopyrite is free floating, very few particles of clean chalcopyrite being observed in the tailing from granular flotation. The chief tailing loss is probably as chalcopyrite occurring as small inclusions in pyrite...

Jan 1, 1939

By NRMR Bhargava

With the increasing use of lead-free solder alloys, low melting point alloy is often required due to the heat- sensitive parts or substrates in modern electronic devices. For such demand of low melting point, the nanostructure lead- free solder alloy, having excellent metallurgical characteristics and a melting point of <215oC, were developed by mechanical attrition of conventional lead free solder alloys (Sn-Ag-Cu, Sn-Ag and Sn-Cu). The decrease in melting point due to nanosize effect was calculated theoretically as function of particle size and the theoretical results were compared with experimental values measured by differential scanning calorimetry. The newly developed alloys have eutectic composition of Sn-3.5Ag-0.7Cu, Sn-3.5Ag and Sn-0.7Cu and the melting point depression found to be 5.10C, 4.10C and 6.20C when the bulk alloys reduced to 80 nm, 92nm and 96nm sizes respectively.

Jan 1, 2009

By George W. Huseman, W. D. Mcmillan

"INTRODUCTION Feldspars represent one of the most abundant groups of minerals and constitute nearly Go percent of the material contained in the igneous rocks. They are grouped in a series of related aluminum silicates with varying amounts of potash, soda, and lime. .Approximately 85 percent of the feldspar produced in the United States is used as a flux in the production of glass, pottery, enamel and sanitary ware, brick, and tile. Notwithstanding the abundance of feldspar in the earth's crust, the only deposits that are worked to any extent are the pegmatites or coarsely crystalline dikes where natural segregation of the constituents facilitates recovery of the feldspar with a minimum of free quartz, mica, tourmaline, garnet, and other iron-bearing minerals that are detrimental in most ceramic industries.Although there are three glassplants and numerous other ceramic industries in Texas, all of the feldspar used in these plants is from other States. In the Llano region of central Texas, however, there are numerous coarse pegmatite dikes consisting primarily of feldspar and quartz in ratios up to 3 to 1. One of the more important of these dikes is the Badu Hill deposit in Llano County, Tex., which was first described by Carl Chelf 4/ in 1942. Following an examination of the deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, in January 1946, a proposal was made to investigate the deposit by core drilling in cooperation with the Department of Ceramic Engineering, University of Texas. This report presents the results of the cooperative investigation, which was begun April 24, 1946, and completed May 17, 1946."

Jul 1, 1947

The object of this paper is to give a description of the new office and changehouse building and equipment at the Zinc Corporation Limited, the office section of which has now been in full use for approximately three years, and the changehouse section for approximately two years. As the expectations of the design have been fully realized, it is thought that this description will be of interest to members and possibly of some use to others faced with similar problems.GENERALIn the centralization of the surface plant around the new main shaft the combined office and changehouse building forms a prominent feature, being located between the shaft and the mill and facing the workshops on the northern side.The scheme for housing all employees in one building was proposed by the Manager, Mr. A. J. Keast, who was familiar with a similar successful structure built at the McIntyre Porcupine Mines Ltd. in Ontario, Canada.The principal features of this building were adopted as a basis for design, and the present layout evolved to suit the particular requirements of this mine.Some of the advantages of the design are:(a) Economy in first cost and space occupied when compared with plants having separate office and changehouse buildings.(b) Easier and more constant supervision of employees and of the plant by the senior staff members.(c) Close contact between officials of all departments.(d) Close covered connection between changehouse and shaft.(e) Avoidance of duplication of ,essential services such as electric power, water, heating plant, sewerage, etc.The Managing Director, Mr. W. S. Robinson, further instructed that the following requirements be adhered to in the new building:(a) Ample accommodation to be provided for office staff and other employees.(b) Special attention to be paid to lighting, both natural and artificial.(c) Working temperatures to be controlled to facilitate comfort and efficiency.(d) The buildings and equipment&apos; to be of a permanent nature with furnishings and fittings of modern design.

Jan 1, 1941

By S. Bang

In recent years, suction piles and suction anchors have been used as underwater foundations for various offshore structures. They have been proven very versatile, effective, and environmentally friendly. This paper describes the load resisting mechanism, installation, and design of suction piles and suction anchors. Also included are brief descriptions of three offshore structures that have recently been constructed using suction piles and suction anchors. They include: a new breakwater system utilizing gravity-type concrete caisson superstructure on top of concrete suction piles; a floating breakwater system utilizing embedded suction anchors; and a foundation system utilizing suction piles for temporary mooring of underwater tunnel elements.

Jan 1, 2009

A simple process for making filter aids from coal by controlled carbonization at 800-1200&#183;C is described.Several possible variations in reactor design have been used experimentally, involving fluidized beds of carbon or inert material, reaction of the particles while entrained in air, and a combination of entrainment and fluidization.Product yields depend upon the composition of the parent coal but are always less than the sum of the ash and fixed carbon values determined by the proximate analysis. The product yield also depends on the air-to-coal ratio, which affects the amount of coal substance burned and the temperature attained. Particle residence time and reactor temperature affect the degree of devolatilization of the product and hence its wettability. The filtration behaviour of carbonaceous filter aids is greatly influenced by the size distribution, shape and physical properties of the particles-parameters which are largely determined by fue type and particle sizing of the coal used.Carbonaceous filter aids are distinctly different from other types commonly used and extensive industrial applications are anticipated in a wide range of industries ranging from food to mineral processing.

Jan 1, 1970

By J. N. Van der Merwe

The research described in the paper was aimed at providing standardized information of cases of failed and intact coal pillars in the form of databases to researchers. It also offered the opportunity to take stock of the pillar stability situation in coalmining and to review the impact of the application of the safety factor formula for pillar design. It was found that the physical parameters of coalmining have not changed substantially over the last four decades. However, changes in the controllable parameters like pillar width, pillar width-to-height ratio and percentage extraction have all moved toward the more conservative side. Scrutiny of the database indicates that of all the failures recorded, only 23 occurred in panels that were mined after 1969, when one can assume that the safety factor formula was fully applied. If the pre-1969 practices had been continued, at least 144 collapses would have been expected. There has thus been a substantial reduction of pillar collapse cases, justifying the cost paid for the formula, which has shown to be in the region of 600 million tons of coal. It is evident that that are distinct differences in the natures of the failures among different coalfields. This justifies the attempts to derive seam or coal field specific strength formulae and is a topic that should be pursued.

Jan 1, 2006

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

SOME notes on the works of the Electrolytic Refining and Smelting Company of Australia will no doubt be of interest to members of the Institute, more especially as much of the work is new to Australasia. As many of the members who may read this paper have not been in a position to visit works of this kind, and are consequently not thoroughly acquainted with all the operations carried on, the author has taken the liberty, in some cases, to enter into explanation which would otherwise be unnecessary. The works are situated at Port Kembla (New South Wales), about fifty miles south of Sydney, and are approachable both by rail and water. The Government has recently built a low-level jetty upwards of five hundred feet long, and intends installing at an early date an electrically operated portable crane to facilitate the handling of material to and from the boats. This will mean: a considerable reduction in the length of time that boats are laid up at the jetty. There are also under construction two breakwaters, which, when complete, will materially assist shipping operation...

Jan 1, 1910

By P. Fauvel, V. Nasri

In January 2001, French and Italian governments signed an agreement for the construction of a new Lyon-Turin railway line. This project includes a tunnel of 53.1 km length and a maximum of 2500 m overburden to be designed for a reference speed of220 km/h. The tunnel crosses major part of the West Alpine geological formations, which are very complex and contrasted in terms of the nature of rocks and the mechanical and hydrogeological conditions. In addition to the twin single-track tubes, numerous intermediary shafts, security station and intervention sites and cross passages should be built to respond to the security, operational and construction requirements. This paper describes the results of the preliminary engineering design and multiple challenges of this very long and deep railway tunnel.

Jan 1, 2005

By Yiming Sun

The 5-mile long Bay Tunnel is a major water supply facility to be constructed under the San Francisco Bay and adjacent marshlands between the San Andreas Fault to the west and the Hayward Fault to the east. The tunnel will have a two-pass lining system consisting of a watertight precast concrete segmental initial lining and a welded steel pipe final lining. Considering the Bay Tunnel?s location between two major active faults, the design earthquake produces a significant peak ground acceleration estimated at approximately 0.6g. To develop a design that can achieve the seismic performance objectives, full dynamic seismic analyses were performed using site-specific earthquake time histories. The analyses considered soil-structure interaction and an evaluation of the transverse and longitudinal effects of the design earthquake. This paper describes the seismic analyses and the design measures recommended to minimize potential adverse effects of the design earthquake on the tunnel final lining.

Jan 1, 2008

By J. E. Friant

Until 1956, drill and blast was the only way to excavate rock. In that year, a tunneling machine using disc type cutters economically bored a small Toronto tunnel. Its amazing 105 ft/day set a new world record and set the stage for a new industry. The Disc Cutter Role in Excavation Mechanical excavation of hard rock is by now deeply ensconced in the heavy civil construction industry. All over the world, from the Swiss Alp Melange to Hong Kong Granite, to New York Gneiss, huge Tunneling Boring Machines (TBMs) create transportation, water and sewer tunnels. Powerful machines, boasting as much as 6000 hp, bore through rock, excavating in excess of 1400 tons per hour. The tool that makes this tunneling phenomenon possible is the single blade, rolling disc cutter. These hardened steel discs, from 15 1/2 to 19 inches diameter are arranged on a rotating cutterhead, to cut concentric circles in the rock. As the machine is propelled forward under great pressure, rock below each cutter is crushed. But the efficiency of the cutterhead is derived from the science of cutter spacing (distance between cutter paths). The majority of the rock excavated is not crushed, but flakes off in chips and chunks. No pick, tooth, or drag type cutting tool can duplicate the performance of a disc cutter. The economic use of drag type tools is limited to as low as 5,000 psi UCS rock strength in massive formations. In weakly bonded, foliated rock, drag tools do better, but are still limited to rock generally less than 15,000 psi.

Jan 1, 2002

By J. Cayouette

In 1995, Louvicourt mine started one of the first paste backfill operations in Canada. From 500 000 t in 1995, the annual paste backfill tonnage produced reached 800 000 t in 1999. The maximum throughput of the surface plant (including binders) is 3500 tpd with a final density of 75% to 76% solids which gives a slump of 15 cm to 17 cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders in a mixture of 20% cement to 80% ferrous slag. In certain stopes, the binder ratio may vary from 2% to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5 Mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.

Jan 1, 2003

By A. Taylor, J. Shelegey, H. Sullivan, J. Doucet

"Historically, performance at Vale’s Clarabelle Mill was measured by Mill throughput and Mill recovery. After the economic collapse in 2008, a series of reviews were performed to drive improvements in business efficiency. These identified that product quality (e.g., concentrate grade, variability in concentrate grade) had a profound impact on downstream processes and suggested that improved control of these parameters would generate the greatest value for the customer (the Copper Cliff Smelter) and the company (Vale). Consequently, a movement was initiated to transform the Mill operating philosophy to consider customer needs as paramount. Systems and strategies used to drive the transformation are described. In 2011, an unexpected furnace failure resulted in decreased capacity at the Copper Cliff Smelter. In response, a two-stage change in production strategy was developed at Clarabelle. The first stage was to modify the ore blend feeding Clarabelle so that the concentrate grade could be significantly increased with minimal impact on recovery. The second stage was a circuit modification to ensure the elevated concentrate grade could be sustained. Execution of the first stage was complete five days after the failure and the second stage was complete within 10 weeks. Steps involved in each stage are outlined and the overall benefits are presented.INTRODUCTION Clarabelle Mill is located in Copper Cliff, Ontario, Canada (approximately 350 km north of Toronto). The Mill treats copper (Cu) and nickel (Ni) sulphide ores. The primary diluents are pyrrhotite (Po) and non sulphide gangue rock (Rk). The process description of the circuits at Clarabelle is documented in the paper by Taylor, Doucet, Blanchette, Barrette & Lawson (2012) in this Proceedings and will not be repeated. The Mill treats ore containing Cu, Ni and platinum group elements (PGE’s) and produces two concentrates; a Cu concentrate and a bulk Cu/ Ni Concentrate (referred to as nickel concentrate). The Cu concentrate is sold to market while the Ni concentrate is thickened at the Mill and pumped to Vale’s smelter complex in Copper Cliff Ontario for further processing. Since commissioning in 1971, Clarabelle Mill has undergone many circuit changes to suit the changing needs and wants of our customers, both internal and external. The Mill processes ores of varying quality, based on mineralogy and size and until 2009 the Mill daily performance was primarily based on throughput. The second key performance indicator (KPI) of “good” or “bad” performance was quality of the concentrate and third; Mill metal recoveries. There were other plant level KPIs such as flotation feed grind size, slurry densities and mass flows to the separation circuit, but for the most part each day was good or bad depending on how many tons were processed through the Mill."

Jan 1, 2012

By W. E. Falck, A. Usubiaga, J. Spangenberg, P. Schepelmann, S. Šolar, D. Wittmer, F. Blanchard

The extraction and processing of mineral resources may be accompanied by environmental impacts. In spite of technological advancements, the enormous increase in production volumes within the last decades has induced sizeable environmental impacts along the life-cycle of products. Beside environmental impacts, social issues associated with mining need to be considered to ensure the social acceptability of mining activities. The project EO-MINERS aims at deploying Earth Observation (EO) tools to inform best practices in mining and to thus assist the global mineral resources industries in their transition to sustainable development. In order to facilitate the handling of complex sets of information requirements from a wide variety of stakeholders, a set of indicators was developed that will inform the process of EO tool and services development. The project strives to enable stakeholders outside the industry to meaningfully participate in decision-finding processes on mining-related issues by developing and providing EO products and services that fit the information requirements. The project has identified a wide range of such information requirements by stakeholders that could be potentially provided by EO tools. The applicability of the EO tools on the local level is tested on three mining sites.

Jan 1, 2011

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation&apos;s mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

Contents.SummaryIntroductionSituation, climate, topographyHistorySize of depositsPrevious investigationsGeological History of AreaMap compilationHistorical summaryNature and Significance of Granitic RocksSynchronous granitesMain subsequent granitesSignificance of types of bathylithsGeological StructureNorth-south anticlineCross-foldingFormation of channelwaysHydrothermal Depth-Zoning at CobarAssociation of Ores with PorphyryOrigin of replacement porphyriesTransgressive porphyriesSummary of ore-porphyry relationshipsSource of the Copper and GoldProspecting Targets, Cobar-NymageeGeneral ApplicationBroken HillThe Bendigo FieldKalgoorlie-Coolgardie, Western AustraliaConclusions

Jan 1, 1950

"For effective steel refining in the ladle (secondary steelmaking) the amount of steelmaking slag that is transferred from primary steelmaking must be limited, because the steelmaking slag contains iron oxide, manganese oxide, and phosphorus oxide. Adverse effects of slag carry-over include increased consumption of deoxidizers, phosphorus pick-up by the steel, and increased ladle refractory wear. Infrared imaging at longer wavelengths is an effective non-contact method to detect slag in the tapping stream. Various devices are used to shut off the tapping stream rapidly. These include slag darts, pneumatic slag stoppers, and slide gates for steelmaking converters, and eccentric bottom tapping for electric arc furnaces. IntroductionOxygen converters and electric arc furnaces are used for primary steelmaking. For both process types, the product (liquid crude steel) has a similar composition: largely liquid iron, with around 800–1000 parts per million (ppm, by mass) dissolved oxygen and low but significant concentrations of carbon, nitrogen, and phosphorus. The steel is tapped into a ladle, which serves as the refining vessel to adjust the final steel composition and temperature before casting.Some steelmaking slag is inevitably tapped with the liquid steel. The mass of steelmaking slag tapped with the steel is termed ‘slag carry-over’. Controlling and limiting slag carry-over from steelmaking is a primary requirement for clean steel production (Fandrich, Lüngen, and Wuppermann, 2008). Steel cleanliness refers to limiting the concentrations of dissolved impurities (such as nitrogen, oxygen, phosphorus, and sulphur) and of nonmetallic inclusions (oxides, sulphides, and nitrides) in liquid steel and in the final solid steel product. Of these, the strongest effect of slag carry-over is on the content of dissolved phosphorus in the liquid steel"

Jun 1, 2019

By D. C. Oldroyd

Western Coalfield?s Tandsi Mine, has difficult support conditions and a history of roof falls, resulting in mining roadway widths and depths being restricted for safety reasons. Rock Mechanics Technology Ltd was contracted to improve the support system to allow the introduction of mechanised room and pillar mining. The introduction of a ?world best practice? bolting system resulted in major improvement in roof stability, allowing mining restrictions to be lifted and Tandsi to become one of the first two Indian mines to introduce a mechanised continuous miner system. The first year?s production was some six times previous levels. Because of the improvement in the support system, RMT was also able to design a partial de-pillaring system suitable for the Tandsi continuous miner districts together with the introduction of monitoring procedures and guidelines to maintain safe roof support conditions. In situ monitoring of pillar and roof behaviour was undertaken as the first pillars were extracted to confirm the design. De-pillaring operations have also proved highly productive, and to date there has been no associated support related major injury or dangerous occurrence. The success of this project demonstrates the potential for mechanised room and pillar mining in India.

Jan 1, 2006

By Jim Bruce

The Transformation AGO project, constructed between 2005 and 2008, featured a foundation trade contract that included design of pile caps and grade beams and construction of 138 permanent micropiles. The new foundation works were constructed within seven different settings ? each featuring a host of attributes challenging to constructability ? inside and outside the existing Art Gallery of Ontario, all while the gallery remained open for business. Transformation AGO resulted in several firsts for micropiles in the Toronto construction market: this was the first micropile trade contract with a multimillion dollar contract value; it featured the first static compressive load test performed beyond 7000 kN on a single micropile; the first static compressive load test beyond 8000 kN on an experimental pile cap supported by two test micropiles; and it was the first publicly funded project to go to tender with micropiles listed as the preferred foundation option. This paper outlines the successful application of micropiles at the landmark Transformation AGO project.

Jan 1, 2011