Search Documents

By Osetzky D, Hesp W. R

The treatment of a hydrobiotite containing 0·64 per cent copper with various soluHons showed that a high percentage (up to 90 per cent) of the copper can be extracted under mild conditions (1 M BCI, 85°C) or withsaline solutions (20 per cent by weight NaCI or NH4F, 400°C). The latter results suggest that the copper is incorporated in the interstratified vermiculite of a vermicuHte-biotite mica and the solutions (NaCl and NH4F) which reacted with the vermiculite without attacking the biotite gave the highest extraction yields.In general, extraction yields with saline solutions increased with the temperature (between 100 and 400°C) and duration (3 or 6 days) of the treatment but were not appreciably affected by the initial pH of solutions.The results of RCI treatment especially may have a bearing on the hydrometallurgical treatment of refractory copper ores where copper is tied to gangue silicates.

Jan 1, 1977

By F. F. Aplan

Though over 100 minerals are known to contain the rare earth (RE) or lanthanide elements, only a few provide the bulk of the world's source of these elements. The principal RE-containing mineral, monazite [(Ce,La,Th,Y)PO4], is recovered by gravity, magnetic, electrostatic and flotation concentration methods, while the other important source mineral, bastnasite [CeFC03], is concentrated by flotation. The processing of the lesser important source minerals is discussed, as is the recovery of the lanthanides from apatite [Ca5(P04)3(F,OH)] where the rare earth elements are present from trace amounts to over 10% as the mixed oxides.

Jan 1, 1989

Six years ago it was my responsibility to give the presidential address, and now that privilege has come my way again. On that occasion we were gathered atWhyalla and I took the opportunity of putting before members some observations on the problems we then faced in Australia, and some gains we had been able to chalk up during those early postwar years. You may recall that we were then just beginning to emerge from the difficulties of postwar reconstructions - of fuel and power shortages, and a grossly inadequate manpower for the tasks facing us. The expansion of manufacturing industry in Australia greatly stimulated by wartime activities, and by the postwar developments of many institutions - ran ahead of the supporting services and of the supply of labour to do thejobs. For many industries this unfortunate state of affairs had meant operating at rates well below their installed capacities and therefore levels of output insufficient for Australia's rapidly growing needs. When I last spoke to you these problems were still with us, though their intensity was beginning to lessen as a result of vigorous efforts by industry and governments to reduce them. But I must confess that my thoughts on that occasion were full of those problems and of the effect they were having on the iron and steel industry of this country-of the coal shortage, the labour shortage, and the many other difficulties we were then faced with - and all at a time when the stepping up of our postwar expansion programme was of vital concern to all of us.What a different picture it is six years later! How greatly has the scene changed for the better. In 1951 Australia's postwar immigration programme was only in...

Jan 1, 1957

By Peter Dunn

London Mining Plc. is developing an iron ore project in Sierra Leone. The Marampa mine is a brownfield development effort, having been operated by others since the 1930?s until low iron ore prices forced closure. Peak production of the prior operations was approximately 2.5 Mt/a in the 1960?s. Following civil war In Sierra Leone, London Mining obtained the mining license in 2006 and commenced activity to redevelop the Marampa mining and processing operations. There are two ore deposits of interest for development as well as a resource comprised of tailings from previous operations. Phase 1 will be the mining of the tailings resource with a 1.8 Mt/a plant producing 66 per cent Fe sinter feed, expandable to 3.6 Mtpa. The first phase is currently under construction with start-up expected in the third quarter of 2011. Phase 2 will include development of the two ore deposits. These deposits are weathered secondary ore and the main primary ore resource. Phase 2 is currently under prefeasibility study and targets a final 16 Mt/a concentrate production in 2016. Outotec partnered with London Mining on testing efforts to develop the magnetic separation flowsheet using SLon VPHGMS machines to process the Marampa material. This paper explains the flowsheet development process for the weathered and primary ores commencing with sample characterization and detailed parametric investigations to evaluate SLon performance. The final flowsheet configuration is explained, including expected circuit recoveries and concentrate quality, clearly demonstrating the performance of the SLon VPHGMS circuit in iron ore tailings treatment applications.

May 1, 2011

The literature pertaining to the electrochemical reaction at the anode during electrolytic reduction of alumina by the Hall-Heroult process is not in universal llgreement about the gaseous product. The possibility of electrochemical formation of CO at the anode was examined using existing data. Although the thermochemistry favours co-evolution of CO and CO2 with CO as the major product, the mechanism of the reaction shows this is unlikely. Since the origin of CO can be more logically explained by non-electrochemical mechanisims, it is concluded that CO2 is the only product from the electrolytic reaction at all current densities.

Jan 1, 1967

By J. M. Krese

This paper gives an overview of the National REAP program emphasizing the program's current status and future plans. A brief historical review of the program will be given containing roof-fall accident trends and statistics. The latest developments in roof control technology and training as it affects the REAP program will be presented. A brief discussion concerning some effects of the implementation of the amendments to Part 75, CFR, concerning roof support is included.

Jan 1, 1988

By Gaulton R

The Commission maintains a data base first computerised in 1957 and containing information from over 18 000 boreholes located mainly in the Latrobe Valley area. Some of the borehole derived information dates from the turn of the century, although most of it has been collected as a result of Commission investigations conducted over the past 40 years. The Resource Data Base contains not only information gained directly from the drilling itself but includes the results of chemical and physical testing on many hundreds of thousands of samples retrieved from boreholes. Replacement value of the Resource Data Base has been estimated to be around $200 million, and it's integrity and accessibility is clearly of paramount importance, not only to existing mining and power generating functions but to the future evaluation and use of the vast brown coal Resource.

Jan 1, 1992

By C. S. Kucukkaragoz

An ilmenite concentrate was reduced in the solid state with carbon under argon atmosphere at temperatures between 1000oC and 1400oC. The ilmenite concentrate and 50% excess carbon were reacted to achieve the highest attainable degree of reduction at each temperature and the reaction products were subjected to a series of analytical work by optical microscopy, X-ray diffraction analysis and SEM ( EDS) analysis. The ilmenite remained unaltered at 1000oC and had a slight change in its composition at 1050oC. A secondary oxide phase containing metallic nuclei was detectable at 12% reduction at 1100oC. The reduction of TixOy took place in a sequence changing the y/x ratio from 2.0 to a value less than 1.0 at 84% reduction at 1400oC. Metallic phase consisted of Fe and C initially and started to include Ti at the later stages. Complete reduction of TixOy to metallic Ti was not possible at these temperatures.

Jan 1, 2005

By C. T. Anderson

In July 1947, the U. S. Bureau of Mines, in cooperation with the Air Materiel Command, started an investigation of zirconium alloys with the object of determining the suitability of such alloys for high-temperature applications. This report covers the preliminary study of about 25 zirconium-rich alloy systems with respect to preparation, fabrication, tensile properties, metallographic structures; constitution, and heat resistance. Obviously, each system could not be investigated thoroughly, and this publication can be regarded only as a first approach. The more promising individual alloy systems will be studied in greater detail and reported in subsequent publications. The study of zirconium alloys on such a scale has been made possible by the U.S. Bureau of Mines developments in the past 5 years On producing zirconium metal. This basic process is similar to that developed by Kroll for producing ductile titanium metal and consists essentially of reducing zirconium chloride by means of molten magnesium. The Northwest Electrodevelopment Laboratory at Albany, Oreg., has produced several thousand pounds of ductile metal in this manner and has a pilot plant producing over 300 pounds of metal per week. Alloys were prepared by melting Bureau of Mines zirconium and the best available grade of alloying element in graphite, with suitable provisions for preventing oxidation. The ingots were quartered longitudinally and sheath-swaged at 850° c. to 3/8-inch diameter rod. Two of those rods were send to Wright Field for room-temperature and 1,200° F. tensile properties. The remaining two sections were used for metallographic, hardness, heat-treatment, and heat-resistance studies. The salient features of this investigation are summarized in table 1.

Jan 1, 1950

By D McClelland, R Whittering

Minerals and Metals Group (MMG) subsidiary Lane Xang Minerals Ltd operates a single site copper and gold mine near Sepon in Lao PDR. Gold production commenced in 2002 and first cathode copper production was in March 2006. Plant throughputs for gold and copper are currently 2.5 Mt/yr and 1.4 Mt/yr respectively; use of a second tailings dam has commenced accordingly. Although the increased catchment area creates opportunities for more storage to reduce demand on other water sources, especially during the dry season, it also creates greater requirements for water treatment capacity.The water balance for mining operations in a tropical monsoon environment with dry winters presents on going management challenges. A successful mining operation depends on a careful balance of water inputs and outputs. The challenge prior to every wet season is having enough storage capacity to absorb potential rainfall. Plant operation in the dry season benefits from water captured and stored from the wet season which reduces the dependence on river water. Release of excess water to the environment is necessary to cope with the overall positive water balance and depends on suitable and effective treatment of water in accordance with the environmental guidelines.Ausenco has recently built and commissioned a second water treatment plant at the Sepon Copper Plant to process tailings decant water.  The objective of the second Sepon water treatment facility is to increase the site water discharge capacity to maintain the water balance and reduce the dependence on river water.  Decant water treatment is required to precipitate the contained heavy metals prior to discharging to surrounding wetlands.  The main metal that needs to be removed from the site water to meet discharge water quality requirements is manganese, as heavy metals are already precipitated to required levels in neutralisation before the tailings are sent to the storage facilities. A site layout provision for removal of manganese to produce a saleable carbonate precipitate is incorporated in the polishing plant design (future installation).

Jan 1, 2009

By A. L. Grabovski

The potential of eccentric cone crushers for fine crushing has been improved by increasing the swing frequency of the moving cone, balancing the crusher, ensuring uniform feed via a rotating funnel with sideways discharge, introducing hyperbolic motion and employing the inertia crushing method, but further improvements to the specifications of existing cone crusher designs are limited by the rigidity of their kinematic coupling. A new design has been developed which combines two crushing modes, stone on liner and stone on stone, each with its own advantages. The main aims are to produce finer materials and to reduce liner weight. The benefits include an increase of more than 10% in the output of fine particles, improved protection of the liner against wear, as a result of filling of the cavities by material being crushed, and the use of almost 20% less material in casting of the liner. The chamber can be used in place of the usual liners of fine cone crushers

Jun 21, 1905

? The economic health and national security of the U.S. depends on the continued availability of, and access to, reliable and affordable energy and mineral resources. However, America is hindered by a costly, inefficient and often redundant regulatory structure that thwarts domestic investment, expansion and job creation. The annual cost of federal regulations in the U.S. increased to more than $1.75 trillion in 2008; averaging $8000 per employee.(The Impact of Regulatory Costs on Small Finns, SBA, 2010) ? The complexity, uncertainty and delays within the current permitting system places the U.S. at a competitive disadvantage with many other countries that have both abundant mineral resources and a more welcoming business and regulatory climate. As a result, American and international mining companies often move overseas or across borders to invest capital, create local employment, and produce the critical minerals America must then import at higher cost, while sacrificing employment and economic stimulus. ? According to Behre Dolbear, the U.S. is ranked lowest globally due to the lengthy permitting period required before mine development can commence. (Where not to Invest, 2010).

Jan 1, 2011

Research personnel from the Bureau of Mines, representatives of the Mining Enforcement and Safety Administration (MESA), and members of the mining industry met with other Government and Industry representatives at three seminars held in Pittsburgh, Pa., November 4, 1975; St. Louis, Mo., November 6, 1975; and Denver, Colo., November L1, 1975, to discuss the results of Bureau-sponsored research on coal mine illumination. The program, aimed at developing suitable illumination systems fur the working; places of underground coal mines, covered hardware development and field evaluation and the status of proposed MESA standards and proposed MESA enforcement procedures. These proceedings contain the opening remarks to the seminars and eight technical presentations an various aspects of coal mine illumination.

Jan 1, 1976

By Wern-ping Chen

Technical and non-technical challenges exist in each mega infrastructure project. It?s no exception to the first US underground PPP Port of Miami Tunnel (POMT) project in Miami, FL. The POMT will connect two man-made islands, the Dodge and the Watson Islands, under the Biscayne Bay within highly porous limestone formation. Permeability as high as 0.1 cm/sec has been identified. Its 41-ft outside diameter, if constructed, is the largest precast segment lining in the US. Besides its geological and hydro geological challenges and risks, local community influence and impacts have controlled the fate of this project. This paper describes its tender design enhancements and the evolving of its slow advancement in resolving local community issues.

By Henry M. Harris

The roll forming of oxide powders was studied in a Bureau of Mines investigation to find the conditions and parameters required to make satisfactory ceramic strip. High-quality porous or dense alumina, zirconia, and porcelain shapes were made by sintering strip roll-formed at room temperature from powders containing minor amounts of binder and water. Strips with thicknesses of 0.04 to 0.08 inch and bulk densities from 40 to 90 percent of theoretical densities were made. The parameters most important to formability were particle size, condition of the powders, and roll gap. Other factors affecting quality were speed and surface condition of the rolls, amount and type of binder, water content, and sintering conditions. Ceramic strip was formed at rates up to 78 feet/minute, which is 13 to 23 times faster than reported by previous investigators, and forming was done in a simple and inexpensive roll unit. Reshaping the strip was possible by cutting, grinding, shearing, and stamping. The following innovations were developed that allow roll processing not normally possible with ceramic powders: (1) Fine-sized powders were made into strip by preparing these as partially sintered granules; (2) thick strip was formed by pressure feeding powders into the rolls; (3) flexible strip was made using a rubber-base bonding agent; (4) corrugated strip was formed on shaped rolls; and (5) porcelain strip was densified and reduced in thickness by rerolling while hot.

Jan 1, 1970

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By D. R. Dolinar, A. T. Iannacchione

Limestone formations in the United States can be subject to relatively high horizontal stresses owing to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rock fall hazard. Rock falls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings has an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orienting the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and off-setting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

By J. R. Thoenen

Profits in the crushed-stone industry, as in any other, represent the difference between selling price and production cost. When consumer demand increases rapidly, as occurred in the crushed-stone industry from 1918 to 1927, selling prices tend to rise. Cost of production usually rises, also, owing to the expense of expanding facilities, searching for and developing new quarries, and purchasing, installing, and operating new equipment. Frequently, also, the inattention of managements to the details of operating costs is responsible for their increase. This is not due to negligence but rather to the necessity of confining attention to the problems involved in producing material to supply orders. When market conditions change and consumer demand becomes stabilized or contracts, the producer r s attention usually is directed to assuring the orders necessary to keep his enlarged facilities busy. Hence, competition increases and soiling prices decline.

Jan 1, 1939

By J. R. P. Aguirre

Minerales Monclova, S.A. de C.V. (MIMOSA) is owned by Grupo Acerero Del Norte (GAN). This company has 4 underground coal mines and 1 open pit to feed it?s steelmaking facilities located in the city of Monclova in the North of México in the state of Coahuila. The current underground mines are Mine 3, 5, 6 and 7 and the future projects are Mines 8 and 9. In the last years Mines 2 and 4 have been closed because they finished their coal resources. The remaining mines have bigger production and developments requirements in order to accomplish the goals of the company. The mines have been working in deeper and gassier areas. These conditions have required improvements in the ventilation design and methane control systems for all the mines. In some cases the ventilation of some of the MIMOSA?S mines has been increased 80%, and besides this, an intensive methane drainage program has been applied using horizontal in-seam boreholes and gob wells. The short-term ventilation plan includes the construction of 3 new vertical shafts with 5 and 6 meters diameter for Mines 5, 6 and 7 and the purchasing of bigger new main and backup fans for each one of these mines. One of these vertical shafts and the purchasing of the first 2 fans is already in process. This paper will explain the evolution and results of the ventilation and methane drainage systems in MIMOSA and the ventilation planning for the future years.

Jan 1, 2009

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semi-gelatin dynamites, three slurry explosives and an ammonium-nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): N02 0.010-0.035; N02, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and C02, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1978