Search Documents

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state requlatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

By L. K. Weaver

Bureau of Mines investigated the progressive impact that petroleum (crude oil and condensate) operations in the Gulf of Mexico have had on onshore operations and the expected effect of increasing activities in this area on future petroleum supplies from domestic sources. The data analyzed include capital expenditures, number of wells drilled, success ratio for exploratory wells, daily production per completion, annual producing rates, and oil reserves. The report compares offshore and onshore data and ascertains trends in petroleum industry operations. Observed data and trends indicate that in the near future Gulf of Mexico development and production will continue to increase relative to total U.S. petroleum activity. By 1975 annual oil and condensate production from the Gulf of Mexico is expected to be in the range of 750 million bbl to 1,150 million bbl, and account for approximately 20 to 30 pct of the estimated total domestic production.

Jan 1, 1969

By J. M. Pei

In this paper, the nonlinear finite element analysis is used to study the support system of a tunnel which is designed to pass through deep-embeded stratum. The rock mass is rather intact, though a section of tunnel will pass through the weak belt. Under the influence of the high ground stress, the condition of stability and the form of support become complicate. This paper, talcing into account the nonlinear properties of rock mass and the Interaction between rock, and support, makes a comparison between the two kinds of soft and rigid support systems, and analysed the changes of their bearing forces.

Jan 1, 2010

By M. K. Larson

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment, and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. But this efficiency also comes at a cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impacts of underlying assumptions in each method is essential to proper use of results in mine design. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health

Jan 1, 2009

By Patrice Favreau

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commerical computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1992

By D. J. Dodds, W. L. Schroeder

INTRODUCTION The plate loading test is a simple, useful tool in rock mechanics. The test consists of applying load to a rock surface and noting the resulting deflections. Plate loading tests are typically used to obtain modulus of deformation and related material properties, but can also provide information on blast damage and in situ stresses (1). Properties obtained are of course dependent on test procedure and test environment . In order to eliminate extraneous results it is essential that the interrelationship between the physical test environment and various rock properties obtained be thoroughly understood. Test interpretation is based upon elasticity methods, and the general assumptions made during analysis which include the following: 1. The rock is homogeneous, isotropic, elastic and continuous. 2. The stress is induced in a semi-infinite solid. 3. The plate is perfectly rigid or completely flexible. 4. Rock properties are independent of in situ stresses. 5. The plate and rock surface are smooth and parallel.

Jan 1, 1974

By J. L. Viljoen

t has long been the drive of the industry and all operations to create an environment that is free of injury and illness. We have come a long way; the leaders, executives, managers, supervisors and workers are to be commended for relentlessly driving to create, what I call a ?White Flag Day Every Day?. Yet I am also aware of the huge shift we still need to create in the industry, on the operations and in the workplaces to have them free of injury and illness. Keywords People, values, care, trust, belief.

Jan 1, 2011

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on total nitrogen oxides (NOX) concentrations were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes.

Jan 1, 2011

By R. T. Langland

Using a finite-element computer model, we have conducted an analytical study of roof behavior in a room-and-pillar coal mine. With standard engineering property in formation and a computer code developed for the Bureau of Mines to calculate roof sag, convergence, and roof-bolt load change, we have calculated the stability of roof-support systems and compared the computed data with experimental data collected during a field investigation at three test sites, one in a development area and two in production areas of a coal mine.

Jan 1, 1978

This report, the third in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more, effectively extract and process minerals and fuels. Environmental considerations, reduced ore grades, and the related increased quantities of material handled were the dominent concerns of the minerals industry in 1972. Productivity increased in most mineral commodities as equipment became more mobile, versatile, and sophisticated. Increasingly, equipment designs incorporated health and safety features. There was considerable interest in the field of energy and in pollution-free metallurgy processes.

Jan 1, 1973

By R. B. Stotelmeyer

Mineral resources, or a potential for their discovery, occur at 34 localities in the Glacier Peak Wilderness and adjacent areas of the north Cascade Range of Washington (see plate). Eighteen of the mineral deposits are in the established Wilderness, four are in or partly in contiguous RARE II (Roadless Area Review and Evaluation) lands recommended by the Forest Service for addition to the Wilderness (A, D and G6031.), three are in adjacent RARE II lands excluded from wilderness consideration, and nine are in nearby roaded areas excluded from the RARE II inventory. Mineral commodities that might be produced from the Wilderness and recommended additions are gold, silver, copper, lead, zinc, molybdenum, arsenic, cadmium, tungsten, cobalt, limestone (marble), pumice, and volcanic cinders. Mineral production from adjacent lands might include most of these commodities, plus antimony, decorative stone, pyrite, silica, and garnet.

Jan 1, 1982

By Thomas Donnelly

Introduction THE Province of San Cristobal is situated on the south side of the island of Santo Domingo about 25 miles west of Santo Domingo city, the capital of the republic. The copper mineralization is found about 1.-CAMP BUCARO. THE TOP OF THE RIDGE IN THE BACKGROUND MARKS THE CONTACT OF THE LIMESTONE AND TUFFS. S miles north of the town of San Cristobal, in the section known as Bucaro Hill; in San Francisco Hill; on the Nigua River; and on the Jaina (Liver. The district is reached by automobile from Santo Domingo city over an excellent road for 25 miles to San Cristobal, and then, by horse-back 6 or 8 miles up the Nigua River to what is locally known as "Camp

Jan 8, 1915

By Vance G. Leak

Leaching of manganese from low-grade Minnesota ores was studied over the temperature range 25° to 225° C at atmospheric and elevated pressures to demonstrate that good recoveries of manganese could be achieved from unroasted ores using reagents available nearby. Various combinations of ore, pyrite, lignite derivatives, and sulfuric acid were tested on a small scale. Pyrite alone required the highest temperature to effect a good extraction, but the combination of pyrite, lignite char, and sulfuric acid solubilized 99 percent of the manganese after 30 minutes of reaction at 75° C.

Jan 1, 1971

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By S. Suwansawat, D. J. Maconochie, C. C. Chang

This paper describes the overall delivery of the tunneling for the Mass Rapid Transit Authority of Thailand’s Chaloem Ratchamongkhon Line in Bangkok and the constraints provided by the alignment. Eight earth pressure balance tunnel boring machines were employed under two major civil works contracts to drive approximately33 kilometers of tunnel in soft saturated ground beneath the crowded streets of Bangkok. Responsibility within the contract for building damage provided an inherent control for ground movement arising form tunneling when the right of way was narrower than the influence zone. These limits affect the earth pressure balance requirements and permissible ground loss. The methods adopted to limit ground movements and deal with the various obstacles to tunneling influenced the design and operation of the machines. The challenges provided by the need to tunnel through numerous lines of piled foundations of canal bridges and overpasses crossing the alignment are described.

Jan 1, 2001

By W Barry Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire, Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1992

By Donald R. Corson

The effects of adding varying amounts of type I portland cement to hydraulic backfill are described. Six different fill materials, each with three cement contents, were tested to determine which fill properties have the most significant effect on cemented strength. Two strength prediction equations, based on the physical and mineralogical properties of the fills, were formulated, and these accounted for 96 and 99 percent of the variability of the data. Results of both unconfined compression and triaxial tests of cemented fills are given, and the effects of moist curing and fill densification on the 7-day strength are discussed. Permeability test data are given, and the decreased permeability due to cement content and curing time is shown graphically. A discussion of the limited evaluation of other potential stabilization additives (expansive cement, fly ash, sodium silicate, gypsum, and asphalt) is included in an appendix.

Jan 1, 1970

By J. O. Lewis, Carl H. Beal

The material for this paper was collected for the most part by C. H. Beal during the years 1916, 1917, and 1918. Many of the conclusions reached in regard to the life of oil wells have already been published by the Bureau of Mines 1 but those presented in this paper deal particularly with the theoretical aspects of oil production. The report discusses some of the fundamental factors governing oil production, taking up first the conditions affecting the. amount of oil in the oil sand, then those factors that control the rate of production of oil wells, and then discusses several related problems, most of which deal particularly with the effect of the production of one well on that of another.

Jan 1, 1921

By L. Cheng

This report presents the results of a Bureau of Mines laboratory investigation of the effect of water sprays in reducing respirable dust that escaped the face area of a full-scale wooden model of a mine en-try containing a wooden model of a ripper-type continuous mining machine and exhaust brattice. Areas examined were (a) the general effectiveness of a low-pressure water spray system mounted on top of the mining machine boom, a high-pressure spray system mounted under the boom, and the combined top-and bottom-spray systems, and (b) the effect of these three spray systems on the capture of coal dust particles of different sizes. Dust was injected into a sump cavity at the face. Airborne respirable dust concentration was mea-sured behind the brattice with a personal sampler and cyclone, and particle size distribution was mea-sured with a cascade impactor. When used alone, the top-spray system captured about 55 pct of the respirable dust in the face area and the bottom-spray system captured 60 pct; the capture efficiency of each system is decreased when they are used simultaneously. From a mass-concentration viewpoint, each spray system preferentially captures larger dust particles.

Jan 1, 1988