Search Documents

By G. van Aswegen

Large structures in mines (faults, dykes, pillars, abutments) fail when the load exceeds the strength. If the loading system stiffness (LSS, also referred to as the ‘local mine stiffness’) is lower than the stiffness of the structure the failure will be unstable. The greater the difference between these stiffnesses, the greater the energy release during unstable failure. A method has been formulated by which the LSS is established through cost-effective numerical modelling while insight into the structure stiffness (source stiffness - SS) is provided by apparent stiffness, a parameter based on the empirical relation between seismic moment and radiated seismic energy of small seismic events from the area/volume of interest. By plotting LSS vs SS a ‘stiffness diagram’ is constructed that is useful for seismic hazard ranking of different structures. A comparative back-analysis of the Dagbreek fault in Welkom, South Africa, (source of the 1990 Matjhabeng earthquake) and two other nearby faults confirm the applicability of the method. An extension of the method, where ‘hazard magnitude’ is used as a measure of the LSS, allows a ‘stiffness diagram’ to be constructed using seismic data only. Les larges structures dans les exploitations minières (failles, dikes, piliers, culées) s’écroulent lorsque la charge dépasse la résistance. Si la raideur du système de chargement (LSS, aussi appelé la « raideur de la mine locale ») est plus basse que la raideur de la structure, l’éboulement sera instable. Plus la différence est grande entre ces deux raideurs, plus l’énergie dégagée pendant l’éboulement instable est grande. Une méthode a été formulée selon laquelle le LSS est établi par modélisation numérique rentable, tandis que la raideur de la structure (SS – raideur de la source) est établie par la raideur apparente, un paramètre basé sur la relation empirique entre le moment sismique et l’énergie sismique radiée de petits moments sismiques dans l’aire/volume en question. On trace le « diagramme de raideur » en relevant les deux mesures (LSS et SS), ce qui est utile pour classer les risques sismiques de structures différentes. On vérifie l’applicabilité de la méthode en comparant la faille de Welkom, Afrique du Sud (foyer du séisme de Matjhabeng en 1990) avec deux autres failles proches. Une extension de cette méthode, dans laquelle on utilise la « magnitude du risque » comme mesure du LSS, permet de construire le « diagramme de raideur » avec des données sismiques seulement. Große Strukturen in den Gruben (Verwerfungen, Dämme, Pfeiler, Auflager) scheitern, wenn die Last die Stärke übersteigt. Wenn die Steifheit des Ladesystems (LSS, auch bezeichnet als `lokale Grubensteifheit’) niedriger ist als die Steifheit der Struktur wird der Bruch instabil. Je grösser der Unterschied zwischen diesen Steifheiten, desto grösser die Energiefreigabe während des instabilen Bruches. Es wurde eine Methode formuliert, durch die das LSS durch eine kosteneffektive numerisches Modell erstellt wird, während ein Einblick von der offensichtlichen Steifheit in die Struktursteifheit (Quellensteifheit - SS) gegeben ist, ein Parameter der auf der emipirischen Relation zwischen seismischem Moment und ausgestrahlter seismischer Energie von kleinen seismischen Ereignissen vom Interessens-/Volumenbereich basiert. Durch das Kartograpahieren der LSS in Bezug auf die SS wird ein `Steifheitsdiagramm ' konstruiert, welches für seismische Gefahrklassifizierung der unterschiedlichen Strukturen nützlich ist. Eine vergleichende Postanalyse der Dagbreek Verwerfung in Welkom, Südafrika, (Zentrum des Matjhabeng Erdbebens 1990) und in zwei anderen nahe gelegenen Verwerfungen bestätigen die Anwendbarkeit der Methode. Eine Verlängerung der Methode, in der die `Gefahrengröße' als Maß für das LSS verwendet wird, gestattet, daß ein `Steifheitsdiagramm' konstruiert wird, welches nur seismische Daten verwendet.

Jan 1, 2003

A record $18.7 billion worth of metals, non- metals and fuels was produced in the U.S. during 1962, according to a year-end estimate from the USBM. The 1962 total value, based on preliminary statistics compiled by the Bureau, was nearly $600 million more than in 1961. Most minerals gained both in value and volume of production during 1962 according to information collected by the Bureau. All mineral fuels except anthracite showed increases. Among nonmetallic minerals- other than fuels-gains exceeded losses by two to one. Metal production held steady as gains and losses balanced.

Jan 2, 1963

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

By Michel Ruel

"PID loops – also known as base layers or regulatory controls – form the foundation of any plant’s control layer and it is generally accepted that PID loop health has a direct impact on the plant’s bottom line. Keeping these thousands of control loops in good health has a direct impact on the plant’s bottom line: it reduces variability, improves quality and throughput, and decreases energy costs and raw material usage. This has been well proven and documented in many articles. In the last ten years, technology has evolved: control engineers can now keep track of control loop performance and link it to the root causes of variability. However, they lack industry-wide best practices and criteria for determining what can be considered as excellent, good, fair, or poor performance. To ensure that PID control loops continue to perform well and meet their objectives, control engineers need a combination of (a) an appropriate monitoring technology and (b) best practices for doing the maintenance of base layer controls.Most plants have limited resources and operate with an increasing number of constraints; therefore, using the right tools and including reports in daily workflow is key for success. This paper suggests roles and responsibilities of key players needed to work toward control performance best practices and discuss organisational changes to succeed.INTRODUCTIONAlthough PID controllers are reliable workhorses in the process industry, they are often underrated. Since the 1980’s, computer control has evolved and the control algorithms used by control engineers have become increasingly complex. However, PID controllers still handle over 90% of the control loops in operating plants. Table 1 shows the savings that can be realized by achieving best-practice in several different process control categories (Brisk, 2004). The savings are expressed as a percentage of production costs."

Jan 1, 2011

By H. S. Rathor

NTPC (National Thermal Power Corporation), a multi-unit organization, is generating 26% of India’s total power. This power is produced from its 14 coal based stations and 7 gas based stations. NTPC is entering into the business of power-distribution, power-trading, setting up of coal mines and diversification in non-conventional energy sector as well. For achieving the goal of the country “Power for All” NTPC has taken a giant stride by entering into Hydro Power generation which is also the cheapest and the cleanest renewable source of energy. In its pursuit for excellence, 800 MW Koldam Hydro Power Project is NTPC’s first venture in hydro sector. In Koldam, hydropower potential will be harnessed by constructing a 163m high earth and rock fill dam in a narrow gorge at upstream end of Bhakra reservoir. The river diversion is envisaged through two parallel, 14m finished diameter ‘horseshoe’ tunnels of length 901m and 934m at village Kian on the right bank, where the river forms a 180° loop. The diversion tunnels are designed to accommodate a flood of 6500m3/sec, taking into account the maximum probable discharge of 200 years return period. The tunnels pass through dolomite and limestone rock formations. The excavation of tunnels was done with drill and blast method. The excavation was attempted from both inlet and outlet faces. During geological investigation a rock fault was located at the outlet area. The location of the fault was such that it was passing through the edge of the Tunnel-1portal and around 30m away from the face of the Tunnel-2 portal. The quality of the rock at Inlet was also poor. To save the portals from slips, excavation of the tunnels was planned to start after the completion of the open excavation and its support system both at inlet and outlet. The tunnel excavation at inlet was envisaged by approaching the tunnels’ portal by constructing a road through 540EL bench and meeting the inlet portals on the upstream end, which would have been ready by mid2003, only after completion of the open excavation and its support system. To save time and cost, it was felt necessary to modify the planning by starting the tunnel excavation simultaneously along with open works both at inlet and outlet. The excavation at the inlet face of the tunnels started in December 2002 after rerouting the approach road to inlet portals through haulage road on the downstream and similarly Tunnel-1 at the outlet was started in the low cover area before completion of open area works. Thus the tunnel—heading excavation was started nearly 06 months early with the change of methodology.

Jan 1, 2005

By John C. Machisak

THE INJURY data and experience at quarries and related plants of the United States are presented in this publication under the following general sections: (A) General injury experience: Tables 1 through 3: Contain current data on the number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 4 and 5: Contain current, data on number of injuries, injury-frequency rates, locution, accident agency, degree of injury, and related employment data. (C) Injury experience by States: Tables 6 through 19: Contain current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data.

Jan 1, 1958

By J. R. Goode

"The Las Cristinas deposit contains about 10.2 million ounces of gold at a grade of 1.3 g/t. The deposit comprises a layer of fully oxidized saprolite (SAPO), a layer of sulphide-enriched saprolite (SAPS), carbonate leached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same level in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper it having been leached and deposited in the SAPS zone.A previous owner started investigation of the Las Cristinas deposit in Venezuela in 1991. Over the next seven years, 1174 holes with a total length of 159 km were drilled, extensive metallurgical testwork, including pilot plant operations, were conducted and feasibility studies were completed. Construction was started in 1997 and again in 1999 but was suspended.Crystallex has been producing gold in Venezuela since the early 1990’s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana, (CVG), to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in early 2003 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and Professor A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-in-leach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the recent testwork, discusses the proposed plant design, and presents economic data."

Jan 1, 2004

By Franz Walchshofer, Mark Kuchta, Nobuharu Isago, Ugur Ozbay, Wolfgang Dolsak

A series of in situ pull test were performed on a new design friction stabilizer bolt with the objective of determining its performance characteristics. The bolt is installed while drilling, thus improving safety and significantly reducing the installation time. An optional expansion element can be inserted into the bolt to provide an end-anchorage, which further increases the bolt’s capacity. In situ tests show that the pull capacity of the 2 m long new design bolt is about 15 tons. When installed with an expansion element, the pull capacity of these bolts becomes as high as 30 tons.

Jan 1, 2005

By C. Doucet

Since 2001, CANMET Mining and Mineral Sciences Laboratories (MMSL) have worked with Falconbridge Ltd. (now Xstrata Nickel) to evaluate trends in the strength development and water retention properties of a novel backfill material for underground mining, called gelfill. Between 2004 and 2006, extensive laboratory tests were undertaken under the leadership of the Deep Mining Research Consortium (DMRC). This paper compares results obtained from samples circulated through a mini-flow loop and a simple mixer. Although many parameters were studied over the last five (5) years, this paper focuses on the investigation of the effect of the mixing method, sequence and time, and the curing environment on strength development and water retention of gelfill. It was found that binder should be added as a powder to the mix in the mini-flow loop, and that mixing slurry in the mini-flow loop as opposed to the mixer generally yielded higher strengths. The practical implications of these observations are the subject of an on-going underground trial that will compare laboratory and in situ properties of regular slurry fill with gelfill.

May 1, 2007

By Michael Schaffer

The paper point out how APC (Advanced Process Control) can be implemented in a stepwise fashion, where each step demonstrates a return and builds towards the overall achievable benefit. Initial efforts focus upon areas that demonstrate the highest potential for quick payback. By attacking small, contained scope, the APC solution is manageable from both a commercial and technical perspective. While this approach results in a slower implementation with correspondingly delayed payback, it provides tangible benefit and addressees the fiscal reality of many operations.

Sep 12, 2005

By Jay Tuttle

THE spiral stoping method of mining was first seen by the writer at the Granby Consolidated Mining, Smelting & Power Company's Hidden Creek mine, at Anyox, British Columbia. Where the method received its name, or by whom it was named, is a question, but it was employed by the Granby Company at their Phoenix mine, in the Boundary district, B.C., as early as 1901-02 after they had tried unsuccessfully other methods at that large, law-grade property. its adoption there was suggested by two miners, John and Steve Swanson, then working at Phoenix, who had previously been employed in the hard iron-ore mines of Michigan and Wisconsin, where they had learned this system of mining. The method proved successful at Phoenix and also, later, at the Company's Hidden Creek mine at Anyox, where some 40,000,000 tons, or more, of ore was mined in this manner during a period of about thirty-five years.

Jan 1, 1939

By B. J. Moore

This publication contains analyses and related source data for 252 natural gas samples from wells and pipelines in 17 States. All of the samples were obtained and analyzed during calendar year 1976 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Eighteen previous publications have presented the results of 11,065 gas analyses prior to 1976. The first 3, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 15

Jan 1, 1977

The dissolution of the naturally occurring mineral zircon (ZrSiO4) is examined after ball milling it with magnesium oxide for up to 100 hours in a laboratory mill. There was little effect on the solubility for the initial two hours where size reduction of the zircon was considered to be the dominant effect. Beyond two hours the dissolution increased as a function of the square root of milling time. X-ray diffraction of the powders did not reveal the identity of the soluble phase. However, a nanocrystalline phase was present after milling and this is thought to be the soluble phase.

Jan 1, 2000

By David Hill

The Australian underground coal mining industry has made extensive use of the Coal Mine Roof Rating (CMRR) classification system for a diverse range of purposes in recent years. These include mining method selection, and coal pillar and roof support design. This paper outlines a series of case histories, from large-scale feasibility studies to local support design investigations, that collectively illustrate the broad applicability, advantages, and usefulness of the methodology, as well as some of the current limitations. The key role of the CMRR in an overall hazard definition methodology is demonstrated for a major Australian project, and some ideas with regard to the future application of the CMRR, in the context of geotechnical risk management within a progressive, highly productive extractive industry, are put forward.

Jan 5, 2007

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By Elsa Olivetti

Life cycle assessment (LCA) is used increasingly as a tool to provide quantitative metrics of environmental impact and inform early stage materials selection decisions. One common challenge in LCA stems from allocation of burden when multiple adjacent products share some of the same processes. A critical example of this is the partitioning of benefit or burden at product disposition in open-loop recycling scenarios. This work reviews the challenge of allocation and investigates the various methods proposed for allocating end-of-life (EOL) burden. Specifically this work examines whether these methods lead to different results and explores the trends in allocation method bias for or against particular materials classes.

Jan 1, 2010

By K. Mondal

A macroscopic approach integrated with microscopic analyses for wettability characterization is presented. Wetting depends on 1) Contact between the dust and the fluid droplets, 2) Wettability of the particles by the wetting fluid, and 3) Wettability rate (due to low contact times). The goal of this paper is to show that the wetting rate is a significant factor in dust control. Samples from the roof, three different horizons of the coal seam and the floor were pulverized to less than 25 µm. Experiments were conducted with known wetting fluids to correlate surface tension and equilibrium wettability. Further analyses were performed in terms of surface charge (zeta potential), particle size, mineral composition, elemental composition, and quartz content. The surface tension reduction was also achieved by the use of chemicals and/or altering the temperature of the water. Two methods were used to evaluate wettability rates: a) near real-time comparison of wettability rates, and b) comprehensive evaluation of the intrinsic wettability rates. The data obtained provides meaningful insights towards the design of engineering controls for an economical solution to dust control in coal mines.

Jan 1, 2012

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 25 jurisdictions of East Asia and the Pacific. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1971

By Steve Kral

The timing was right for SME to celebrate its 50th anniversary in February as a member society of AIME. The mining industry is in the midst of a commodities boom that appears to have legs. Not only is the demand for metals, construction materials and the like increasing in developing nations, but developed nations have also seen the demand for those materials increase at impressive rates. So, in addition to networking and seeing old friends, attendees at the SME Annual Meeting and Exhibit in Denver, CO. Feb. 25-28, had several reasons to enjoy the week — a healthy industry and their society’s landmark anniversary. This annual meeting was held jointly with the Colorado Mining Association’s (CMA) 109th National Western Mining Conference.

Jan 1, 2007

By David C. Yang

A packed column (or static tube) flotation system is an innovative technology which utilizes a controlled dispersion reagent scheme and a new machine. The unique aspect of the machine is its packed-bed design permitting an unlimited froth bed height with countercurrent water washing for effective processing of fine particles. In operation, the conditioned ore slurry is fed into the middle section of the column where separation processes begin. Air, introduced at the bottom of the packed column, contacts the hydrophobic particles and floats them off continuously as the feed is added, while the gangue sinks to the base of the column. The system functions efficiently because intimate particle-bubble contact is achieved by the packing design which has no moving parts and requires no ancillary air-bubble generator. Other attractive features of the packed column flotation include high throughput, low power requirements, and simple control. Results from laboratory and pilot plant tests of this system show remarkable improvements over current industrial practices on a wide variety of ores and coals.

Jan 1, 1988