Search Documents

By B. Soundara, A. Suganya, S. Selvakumar

"Expansive soils have a potential for shrinkage or swelling under changing moisture content. Attempts were made to reduce the swelling potential of expansive soils with conventional additives such as lime, cement, etc. and non-conventional additives such as industrial wastes. In this research an attempt is made to study the feasibility of using granulated waste expanded polystyrene (EPS) as an additive to expansive soil to control swelling. To investigate the effect of mixing waste EPS granules with expansive clays, three expansive soils with different plasticity index were manufactured in the laboratory by mixing sand with sodium bentonite of various proportions. A series of standard proctor test, California bearing ratio (CBR) test, one dimensional free swell and swell pressure tests were performed on these soils. Test results show that the inclusion of EPS granules significantly reduces the percent swell and swelling pressure when subjected to one-dimensional free swell conditions. The dry density and CBR values decrease with increase in EPS content and increased plasticity of the soil.INTRODUCTIONExpansive soils cover an area of about 257 Million hectares on the earth’s surface (Dudal et al. 1965). In India, the area covered by expansive soils is nearly 20 percent of the total area (Mohan et al. 1961). Movement is usually in an uneven pattern and of such a magnitude as to cause extensive damage to various structures, especially lightly loaded structures or pavements (Chen 1975). Stabilization is one of the methods of treating the expansive soils to make them fit for civil engineering purposes. The variety of stabilizers may be broadly divided into three groups (Petry et al. 2002): (a) traditional stabilizers (lime, cement etc.), (b) by-product stabilizers (fly ash, quarry dust, phosphor-gypsum, slag etc.) and (c) non-traditional stabilizers (sulfonated oils, potassium compounds, polymer, enzymes, ammonium chlorides etc.). Apart from these, a number of other ground improvement techniques such as sand cushion technique (Satyanarayana 1966); cohesive nonswelling (CNS) layer technique (Katti 1978) were adopted for the stabilization of expansive soils. Expanded polystyrene (EPS) is a polymeric foam normally available in white colour and is a wellknown packaging material. The geotechnical specialists recognize EPS as the most commonly used geofoam material, a type of cellular geosynthetic which has been in consistent use in geotechnical applications since the early 1960s (Horvath 1995). EPS has very low thermal conductivity and nearly 98% of the volume is air (Lye et al. 2002). EPS has many exceptional properties such as being lightweight, thermal insulating, shock-absorbing and having low-water pick-up, etc. EPS find its applications in geotechnical engineering as light weight fills in the form of blocks (Refsdal 1985, Karpurapu et al. 1992, Zou 2001, Ikizler et al. 2008). EPS can be used as compressible inclusion and as a vibration damper (Horvath, 1994&1995). EPS is also used in lightweight concrete owing to its lightweight, excellent heat preservation and sound insulation properties (Ravindrarajah et al. 1994; Miledet al. 2004 and Babu et al. 2005). Waste EPS granules have been used in with horticultural soils to improve a number of soil characteristics like improving drainage, lightening heavy soils and improving water uptake capacity of soils (Scheirs 1998). Furthermore, it was also used as sub-base materials for pavements and railway track beds (Hanna 1978; Duskov1996), construction materials for floating marine structures and fenders in offshore oil platforms (Bagon et al. 1976), sea beds and sea fences; as an energy absorbing material for buried military structures, (Perry et al. 1991)."

Jan 1, 2017

By J. H. Zietsman, S. Maharajh, J. Muller

In the chlorination process for TiO2 pigment production, blends of titania feedstocks such as ilmenite, synthetic rutile (SR), natural rutile, upgraded slag, and chloride-grade slag are reacted with coke and chlorine at a temperature of around 1000°C to form TiCl4 (the main product) and other waste metal chlorides. The TiCl4 is the main feed material for the TiO2 pigment-making process. Feeding different titania materials to the chlorinator affects the amount of coke and chlorine required for the process, the amount of waste generated, waste disposal costs, the amount of TiCl4 produced, and bed build-up rates. These factors influence the value of the feedstock. Generally, a higher TiO2 feedstock is more valued since less waste is generated and less reagents are consumed. To quantify the impact of different feedstocks on the chlorinator, a techno-economic model was developed to describe the chlorination process and estimate process variables at steady state. This paper describes the development of the model and studies in which the model has been used to quantify effects of using different feedstocks.

Jan 1, 2015

By Taylor G. H

The Triassic Ipswich (SE. Queensland) coals are of bituminous rank. The more exact rank of individual samples was determined by measuring the reflectance of the vitrinite. While in general the rank of the coals increases with stratigraphic depth, minor reversals, probably related to igneous intrusions, occur.The Ipswich coals form a coherent group so far as petrographic type is concerned. All are comparatively rich in vitrite and clarite, cutinite being the common maceral of the exinite group. The mineral contents of all the coals are comparatively high, clay and quartz being most abundant. The coals appear to be of essentially autochthonous origin, and to have been formed under conditions of fairly rapid subsidence.While the use of the coals is at present restricted to combustion, most have pronounced coking properties, as would be predicted from their petrographic composition and reflectance. However, the high mineral content of the coals would be a limiting factor in their use for coke-making.INTRODUCTIONDuring the last ten years, the Division of Coal Research, Commonwealth Scientific and Industrial Research Organization has carried out an extensive investigation of Australian coals, providing a wide range of analyses of most of the important of them. Special attention has been given in recent years to Queensland coals.Most seams were sampled as a number of subsections, enabling the internal variations, as well as the overall properties, to be assessed. The lenticularity of many of the mineralrich layers may tend to limit the significance of the samples, particularly in respect of ash yield, but although the vertical distribution of mineral matter may vary considerably from one sampling position to another, the lateral variation of the total mineral matter in the whole seam may not be great.Apart from extensive chemical analyses and utilization...

Jan 1, 1963

Tyre costs constitute 20-40 per cent of the operating cost of large haulage trucks, and tyre pressure maintenance is an important factor in minimizing costs.In the past, control over the hot (built-up) pressures of earthmover tyres has been inaccurate and inconsistent because it has not been possible, in a practical way, to measure the tyre's contained air temperature.A method for measuring this contained air temperature has now been devised using a bi-metallic probe thermometer inserted through the valve stem. Using these measurements in conjunction with a pressuretemperaturechart drawn up using the general gas equation, very accurate control over hot tyre pressures is now possible.

Jan 1, 1979

By F. C. Langenberg, J. Chipman

Jan 1, 1959

By R. C. Corey

GERMANIUM is an element that has come into widespread use in the electronics industry in recent, years. So far this increasing demand has been, met by ample supply: however, the future balance is uncertain, and the need has been recognized to discover additional domestic sources of germanium. This investigation was conducted to study the possibility of obtaining a potential supply of germanium from coal or coal ash. It has been known for some time that coal contains germanium; the discovery that By ash from coal-fired boilers often contains appreciably more germanium than the original coal suggested the possibility that coal ash might be an abundant and economical source of this element. In this study the concentration of germanium was determined in numerous samples of coal and ash. A number of miscellaneous waste materials also were examined in the course of the investigation; the results are reported as a matter of general interest. The methods and equipment employed are discussed in detail. Sample-preparation and analytical techniques are described in the appendix. Spectrographic analyses were made on a total of 639 samples, including coal, coal ash, slap ash from lignite and peat, wood ash, and various inorganic materials. Qualitative analyses were run on all samples, and quantitative determinations were made on those samples that contained enough germanium to be measured by this method The lower limit at which germanium can be determined quantitatively by spectrographic analysis is 50 parts per million (p. p. m.), but concentrations of less than 20 p. p. m. can be detected qualitatively.

Jan 1, 1959

By Arno C. Fieldner

In view of the widespread interest in the production of synthetic liquid fuels from solid and gaseous fuels to supplement declining reserves of petroleum, and the many requests that are now being received for information on the subject, this bibliography of Bureau of Mines contributions has been compiled. In addition to the publications issued by the Government in printed or mimeographed form, references are included to articles written by the Bureau staff for the technical press and to cooperative reports of work done jointly with States, colleges, and industries. References are given under each section in chronological order. Bureau of Mines bulletins, technical papers, and Minerals Yearbooks are printed and are obtainable at the prices indicated from the Superintendent of Documents, Government Printing Office, Washington 25, D. C. If no price is given, the publication is out of print. The price of entire volumes of the Minerals Yearbook or of reprints of certain chanters may be obtained upon request. Any orders or remittances in payment for these publications should be cent directly to the Superintendent of Documents and not

Jan 1, 1945

By E. Swart

The purpose of this paper is to provide an overview of the current legislative framework for mine closure within South Africa as well as the new requirements in terms of the Mineral and Petroleum Resources Development Act, 2002. The roles and responsibilities of Government, the mining industry and other stakeholders and confusion caused are also highlighted.

Jan 1, 2003

By K. Kohli

A case study involving a historic structure undermined by longwall mining is presented in this paper. The location of this study is in South Western-Pennsylvania; USA. The structure is 150-years old and subsided 4.5 feet. This paper discusses the mitigation measures taken to reduce the subsidence damage and its effectiveness.

Jan 1, 2002

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By J. M. Font, R. G. Reddy

Jan 1, 2004

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By D. Norval

Keywords: Pyrometallurgy, slag, metal, entrained, granulation, ferromanganese Water granulation of certain slags with high metal entrainment has customarily not been practised, not only due to the belief that such processes are too dangerous and unproven in the pyrometallurgical industry, but also that it might not be economically viable or environmentally acceptable. General slag granulation, on the other hand, is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. Thus, purpose-designed granulation and solidification processes are discussed, taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte, or alloy responds in similar fashion to a granulation practice. This paper addresses three issues, namely: ? Water-granulation of BOF steel slag, without processing it to render it environmentally safe, physically and chemically acceptable for use by the construction industry, and the process economical ? Processing air-cooled BOF steel slag to change its physical and chemical properties to be acceptable for various uses and extracting metallic and bound iron ? Processing air-cooled or molten manganese slag to lower its manganese content to a level that is acceptable from an environmental and health point of view, and extracting FeMn-alloy of acceptable composition. The latter process culminated in a patented process to extract FeMn from air-cooled and molten manganese slag, and, at the same time, produce a hydraulic (cementitious) slag, thus transforming a possible hazardous by-product into virtually 100% saleable products.

Jan 1, 2011

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projects programed by the Bureau of Mines for fiscal year 1979 (October 1, 1978--September 30, 1979) under its Nine Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's miners.

Jan 1, 1979

By Gregory J. Canivan

Three test pile programs were conducted in Charleston, South Carolina to evaluate differences in bearing resistance due to installation methods. The tested piles were installed with impact hammers and vibratory drivers through soft clays and/or loose sands into the Cooper Marl, a stiff calcareous marine clay or silt. Piles driven into the Cooper Marl experience significant capacity gain with time following initial installation due largely to pore pressure dissipation. Pile size and pile type were both known to affect pore pressure generation during installation and subsequently the capacity gain with time. The test programs were primarily conducted to optimize pile design values and construction methods with regard to trestle construction but the results also contribute to the understanding of driven pile behavior. High strain dynamic testing was performed on several open-end pipe and H-piles. The measured difference in long-term bearing capacity of the H-piles as a result of the two installation methods was negligible, while the short-term bearing capacity of the pipe pile was larger when the piles were installed using impact hammers. The lower short-term resistance in the vibratory driven piles is attributed to larger excess pore pressures generated during installation compared to those generated during impact driving.

Jan 1, 2002

By Richard Miller

RECENT studies of creep have made it apparent that plastic deforma-tion may occur in metals under stresses less than the elastic limit as deter-mined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapsell1 said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a. definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was deter-mined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instru-ments by A. W. Hanson4 on zinc and by Podaschowsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc.

Jan 1, 1936

By J. P. Jarrell

Environmental considerations are of increasing importance in determining the acceptability, schedule and cost of expansion ofCanada's uranium processing industry. Environmental considerations must be addressed in the early stages of facility planning. This results in a dilemma, as the process data needed to predict physical environmental impacts are not yet available from process design activities. Hence, a business risk is incurred if plant design is carried forward to meet these requirements prior to project (or site) approval. On the other hand, project scheduling normally mitigates against leaving process design engineering until such time as project approval is obtained. This paper examines the experience gained in Eldorado Nuclear's proposed expansion of refining capacity as viewed by an environmental engineering consultant. The history of the project and the relationship to process design functions in the two-year period prior to the Port Granby environmental hearings are reviewed. During the Port Granby public hearing, there was a consensus that normal operation of the proposed refinery could be successfully integrated with the site's natural environmental constraints. Moreover, the radiological impact from plant operations was demonstrated to be inconsequential. However, concerns were raised relating to plant upset and accident situations. These concerns are summarized. Process data requirements identified during the environmental hearings are discussed. Finally, the concerns for on-site burial of radioactive waste are reviewed. These concerns focussed on long-term stability of the waste in the presence ofgroundwater transport, erosion and glaciers. The AECB's position on waste management with regard to this project is reviewed in light ofthe implications for design.

Jan 1, 1979

By D. Millgard

Dennis Millgard introduced the Session by hoping that participants to the Conference would also share their piling problems. He then invited the first speaker to present his paper. Paper 5.1. Pat Kelleher commenced by saying that he belonged to a one hundred year old firm that had experience in the New York Harbour area. They were often asked to assess the integrity of many waterside structures such as piers, walls, and docks which were deteriorating whilst still in use. The earliest structures, built in the 1800's, were on timber piles. These have now changed to Steel H and tube piles and concrete piles. Usually they were called in when the structure was showing signs of distress, or had reached the end of its life but could not be closed. In particular, they had found that marine borers had returned to New York Harbour because of the improved quality of the water. There is now a far greater incidence of attack on the timber piles than when the water was polluted. Repair is usually carried out by encapsulating the pile within the tidal range of about -2ft to +8ft (-0.6 to +2.4m). Reinforced concrete forms, reinforced fibre jackets, or nylon bags are used. Reinforced fibre jackets are used with a protective coat on the pile, while nylon bags prove the cheapest method.

Jan 1, 1991

By Steve Wilson, Bern Klein, Jeff Drozdiak, Stefan Nadolski, Andrew Bamber

"In the adaptation of high pressure grinding rolls (HPGRs) to hard-rock mining applications, circuit development has mainly focused on placing HPGRs in the role of tertiary crusher in the preparation of ball mill feed. In order to take advantage of the potential energy benefits associated with HPGR and stirred mill grinding technologies, work was done to investigate the potential of and resultant energy benefits of placing the HPGR in series with a high speed stirred mill in replacement of the conventional cone crusher / ball mill arrangement. The proposed circuit was designed to operate with two stages of HPGR grinding followed by high speed stirred milling.Using a pilot-scale HPGR unit inline with a 20 liter stirred mill, the design criteria, circuit arrangement and consequent comminution energy requirements for a circuit processing copper sulphide ore from Teck Resources’s Mesaba Copper project were determined. These results were then compared to two other circuits, an HPGR / ball mill circuit and a conventional crusher / ball mill circuit processing the same ore.The testwork indicated at a proof-of-concept level that the HPGR / stirred mill circuit could potentially be appropriate for this duty and further work on the concept is merited. While the results indicate that the HPGR component of the circuit was more energy efficient than conventional cone crushing, the energy efficiency of the stirred mill was found to be lower than that of a comparable ball mill undertaking the same duty. However, increased energy efficiency of the stirred mill portion of the circuit is possible with further optimization and further work on the concept is indicated."

Jan 1, 2010

By Masanoub R. Fujioka

A brief discussion of the methodologies involved in dewatering practices, particularly as used in Hawaii in coralline formations. A description of early dewatering practices includes a number of case histories; later dewatering practices also are detailed with case histories. There were disasters and some successes. Grouting generally was not successful. Deep wells are technically feasible and generally the economical solution to deep basement construction.

Jan 1, 1986