Search Documents

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

By R. W. Welker

A technique was developed for sampling and analyzing airborne dusts in diesel-operated, underground, metal, and nonmetal mines. Samples were taken using personal respirable samplers, operated as area samplers, and an 11-stage cascade impactor. Real-time particle size distribution and concentration measurements were made with a quartz crystal micro-balance cascade impactor and a portable electrical aerosol analyzer. The materials characterized were minerals (by XRD), elements (by XRF), particle size distribution and concentration (gravimetrically), and organic constituents (by HPLC). The method was used to characterize dusts generated at the chute pulling operations on the main haulage level of an underground tungsten mine. Analysis showed that respirable dust concentration ranged from 0.8 to 2.3 mg/m3. It consisted of silica (3-7%); organic constituents from diesel exhaust (0.11-0.31 mg/m3 equivalent airborne concentration); and mineral dust (39-100%). The remainder was diesel exhaust particles. It was concluded that size selective sampling may be used to estimate the ratio of diesel exhaust to nondiesel dusts in the respirable fraction.

Jan 1, 1982

By Jeffrey L. Pagnutti

Train derailment can lead to loss of capital, damage to the environment, and loss of life. Machinery condition monitoring techniques can be used to develop a structural health monitoring system for railway track to detect faults at the incipient stage, before catastrophic failure occurs. This study uses vibration measurements from a novel material haulage unit to develop a decision support system for railway track maintenance. A variety of feature sets and classifiers were compared to determine the optimal configuration for fault detection. The results highlight the shortcomings and advantages of certain methods and describe the process in which the optimal result was obtained. The Parzen data descriptor paired with a refined statistical feature set performed the task of fault detection with less than five percent false positive and false negative classification error. Overall, the outcome of these experiments indicated that condition monitoring of railway systems is a promising approach for fault detection and has the potential to avoid catastrophic failure.

May 1, 2013

By Robert M. Valentine, Randall L. Lentell

Interpretive geotechnical investigations were performed for the construction of approximately 15,250 m (50,000 ft) of wastewater interceptor tunnels in Austin, Texas. Subsurface materials consist of claystone (or clay shale), siltstone, altered volcanic tuffs, chalk and limestone. Special conditions include multiple crossings of Onion Creek with cover ranging from about 1/2 to 3 m (2 to 10 ft.), and the potential for mixed-face conditions consisting of water-bearing gravels overlying clay shale or siltstone. The methods and results of the geotechnical investigations are discussed and the inferred construction conditions are compared to those encountered during tunneling. A suggested format is presented for interpretive geotechnical reports for underground construction projects.

Jan 1, 1985

By R. R. Wells, G. M. Potter, R. Havens, W. W. Agey

"INTRODUCTION As part of the program of investigating possible domestic sources of manganese, ore-dressing studies were conducted at Salt Lake City, Utah, on five samples of manganese oxide ore obtained by mining engineers of the Bureau of Mines from the Havasu Lake District, California and Arizona.Two lots of radically different ores were procured from the Arizona Manganese claims 30 miles above Parker Dam, Mohave County, Ariz. One of the original 11 claims has been flooded by Havasu Lake, formed by Parker Dam. The claims are owned by R. H. Thompson, Parker Lumber Co., Parker, Ariz. The 2-ton lot of high-grade ""TA"" ore represented ore occurring as pyrolusite and psilomelane accompanied by a black calcite gangue in lenses along a series of fault planes in granite. A half-ton lot of low-grade ""TB"" ore was taken from a large lense of reddish iron-bearing material outcropping on another section of the property.A 2-ton lot of ore was taken from the Jones property, 8-1/2 miles southwest of Powell, Mohave County, Ariz. At the time of the investigation, the property was leased by J. H. Jones, of Oatman, Arix., from the owners, the Atchison, Topeka, & Santa Fe Railroad Co. The ore body was described as a re¬placement in a sandstone formation in a region that has been faulted extensively."

Dec 1, 1947

By Gerald H. Groenewold

Reclamation of surface-mined landscapes is commonly defined only in terms of biological productivity. Other critical concerns associated with surface mining include the long-term quality of groundwater and stability of the postmining landscape. Meaningful reclamation design must address all these concerns. Reconnaissance of postmining landscapes indicates that three types of instability occur in these settings. These include: area-wide settling, localized collapse, and piping. Area-wide settling is most pronounced during the first year after contouring but appears in precontouring valley areas where frozen materials are contoured with a dozer. Although severe in some settings, development typically ends within one year. Piping appears to be a severe and long-term problem in some settings. Piping usually begins soon after contouring ceases and may continue for several years. In some postmining landscapes, piping has only started to develop after as many as five years of apparent stability. Piping is controlled by a combination of physical and chemical conditions in the spoil. A key factor is the presence of highly dispersive materials in the near surface. The design of a stable postmining landscape requires the integration of severe critical factors. These include: 1) detailed knowledge of the distribution of overburden materials with emphasis upon the delineation of highly sodic sediments; 2) proper equipment selection; and 3) a consideration of climatic factors. For reclamation to be successful, it must consider the entire landscape, not merely the soil zone. Any approach short of this will lead, at best, to temporary solutions.

Jan 1, 1980

By Gualberto Salas Torrelly

El avance tecnológico en los sistemas de iniciación en voladura abarca desde el sistema convencional (Mecha de Seguridad y Fulminantes hasta el sistema de iniciación electrónica, donde a través de un control de vibraciones se controla la energía liberada en un disparo, optimizando la fragmentación y disminuyendo el daño a las paredes del pit. En ese sentido, el sistema de iniciación con detonadores electrónicos, fija con claridad los conceptos de precisión, flexibilidad y seguridad. Por ello, el presente trabajo señala el uso de detonadores electrónicos por la Sociedad Minera Cerro Verde con la finalidad de evaluar sus resultados en seguridad, precisión, fragmentación, vibraciones, y control de daño a las paredes de la mina. Los resultados fueron óptimos -en tanto mejoró la fragmentación, el proceso de carguío y se incrementó el flujo en chancado primario.

Sep 12, 2005

By Douglas B. Silver

Super Cycle future The final topic is mining?s future. The most important questions are ?How much longer is the Super Cycle going to last? What should we expect to see going forward? How will the Super Cycle end?? Three possible scenarios follow. Scenario one: Super Cycle has peaked Kathy Casey-Kirschling is officially the first Baby Boomer. She was born Jan. 1st, 1946. If you google ?first baby boomer,? she?s the one that shows up. A Baby Boomer is anybody born between 1946 and 1964. In the United States, it represents about a quarter of the population ? approximately 76 million people. The Baby Boomer generation is going to change the economics of the world because there are so many in the generation. A review of spending patterns indicates that the largest amount of discretionary spending occurs between the ages of 49 and 52. Retired people tend to live on fixed incomes so they have less discretionary income. They also tend to downsize their house, which may contribute to the housing glut and the need for a lot less metal. Therefore, the upcoming retirement of the Baby Boomer generation could result in a massive shift in economic spending resulting in the peaking of the Super Cycle. Figure 1 is an index graph from the Toronto Stock Exchange (TSX). The index has recently peaked. A lot of people see that as a sign that bad things coming our way. A careful review of different commodity prices also suggest that the peak has occurred and it does not seem to matter which commodity prices are considered. Copper prices have seen a peak as have nickel prices. Nickel and molybdenum displayed the same trend with a peak in 2005 as did zinc. Uranium, which has single-handedly tried to behave like the dot com craze, has also peaked.

Jan 1, 2008

By H. Stanley Benson

This report is an account of research conducted to improve the performance of and then further field test Draft Power Sensor (DPS) equipment, the use of which enables a bulldozer operator to optimize his machine's work rate. Significant improvements were made in DPS hardware, and extended field testing was conducted at two working strip mines: the Glenharold Mine of Consolidation Coal Company, near Stanton, North Dakota, and the Beulah Mine of Knife River Coal Company, near Beulah, North Dakota. This report documents the increase of bulldozer work production by greater than twenty percent while using the Draft Power Sensor when compared to baseline work production without benefit of the Draft Power Sensor. Research was done by Southwest Research Institute under contract with the Bureau of Mines.

Jan 1, 1980

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By B. P. Simser, R. K. Brummer, A. Mortazavi, P. P. Andrieux

"A large-scale panel destress blast was fired at Brunswick mine in the fall of 1999 in order to reduce the ground stresses in a critically important neighbouring mining region. This work, sponsored by the Mining Division of CAMIRO and Brunswick mine, consisted in heavily choke-blasting — and subsequently leaving in place — a massive waste sulphide pillar in the southwest end of the 1000 m level. This paper describes the approach and design methodology used to try to maximize breakage in the rock mass in the area to destress, while minimizing damage to critical infrastructures in the vicinity. The loading operations, as well as the results of the blast — in terms of its field performances, as recorded by near-field blast vibration monitoring equipment, visual postblast assessments and measured impact on the regional stress field — are discussed as well. A brief comparison between the measured stress changes and inelastic numerical modelling of the test site is also presented.Un tir à grande échelle de relâchement des contraintes dans un pilier a été effectué à la mine Brunswick à la fin de l’automne 1999 dans le but de diminuer les contraintes de terrain dans une très importante zone de production adjascente. Ces travaux, financés par la division minière de CAMIRO et la mine Brunswick, consistaient à tirer violemment sans aucune face libre, et à laisser en place, un pilier de sulphures massifs au sud-ouest du niveau 1000 m. Cet article décrit l’approche et la démarche conceptuelle utilisées pour tenter de maximiser les fractures dans le pilier visé, tout en minimisant les dommages collatéraux à des infrastructures critiques se trouvant dans les environs immédiats. Les opérations de chargement des explosifs et les résultats du tir — en termes de ses performances, telles qu’évaluées par de l’équipement de monitoring rapproché des vibrations de tir, d’observations visuelles, et de son impact sur les contraintes de terrain locales — sont également discutés."

Jan 1, 2003

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

By A. M. Milev

A stand-alone instrument especially designed for recording strong ground motions was used in this study to create a large data base of peak particle velocities measured on stope hangingwalls. A total number of 58 sites located in stopes mining the Carbon Leader Reef, Ventersdorp Contact Reef, Vaal Reef and Basal Reef were monitored. The peak particle velocities were measured at the surface of the excavations to identify the effect of the free surface and the fractures surrounding the underground mining. From the monitoring results obtained, the velocity criterion of 3 m/s will bean adequate value that support systems have to sustain during a rockburst in most cases. However, PPVs in excess of this criterion were recorded, and some PVDs were damaged or irretrieveable, a consequence of which was that possible extreme events were not recorded. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response, defined as the ratio of the measured peak ground velocity to the peak ground velocity inferred from the mine seismic data. The site response measured at all mines studied was found to be 9 ±3 times on average. Values of the site response did not vary significantly with seismological parameters such as peak ground velocity, hypocentral distance and source radius.

Jan 1, 2005

The MineSight Schedule Optimizer (MSSO) is a new production scheduling tool developed by Mintec, Inc. using mixed integer linear programming (MILP) techniques. This tool was developed to solve the short- and medium-term schedule problems for surface and underground mining operations that involve multiple mining areas, multiple processes, multiple destinations and blending requirements. MSSO finds the optimum schedule in each period that achieves the objective while satisfying comprehensive product quality and quantity requirements as well as physical and technical constraints. Using the MineSight Planning Database (MSPD) as a central data hub, MSSO seamlessly works with MineSight 3-D (MS3D) block models and third-party data, MineSight Interactive Planner (MSIP), MineSight Haulage (MSHaulage) and MineSight Activity Planner (MSAP) to prepare data, formulate MILP models, calculate, report, fine-tune, save and visualize schedules. This paper presents the features and capabilities of MSSO. A case study is also given to demonstrate the applications of this new tool.

Jan 1, 2009

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don't consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

[ ]

Jan 1, 1994

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By R. E. Whitehead

"Alkali/alumina and MgO/alumina molar ratio plots graphically portray both chemical and mineralogical changes accompanying potassic, phyllic, argillic, chloritic, and alunitic alteration of quartz monzonites and granodiorites hosting porphyry (as well as lode and greisen) ore deposits. The molar ratio plots can be used to identify different types of alteration. In most cases, the identification based on molar ratios coincides with petrographic data. In those instances where the molar ratio and petrographic identifications do not agree, the mineralogy might need to be re-examined. Hydrothermal alteration studies using trace elements could benefit from the application of complementary alkali/alumina molar ratio plots.Le diagramme des rapports molaires alkali/alumine et MgO/alumine illustre clairement les changements chimiques et minéralogiques qui accompagnent les altérations potassique, phyllique, argillique, chloritique, and alunitique des monzonites à quartz et des granodiorites encaissant les gîtes de type porphyrique, ainsi que des veines et des greisens qui leur sont associés. Les diagrammes de rapports molaires peuvent être utilisés pour identifier divers types d’altération. Dans la plupart des cas, l’identification basée sur les rapports molaires est en accord avec celle basée sur les données pétrographiques. Là ou il y a désaccord entre les rapports molaires et les données pétro-graphiques, il peut être nécessaire de réexaminer la minéralogie. Les études de l’altération hydro-thermale accompagnées d’une étude des éléments traces auraient avantage à utiliser un diagramme des rapports molaires alkali/alumine."

Jan 1, 2009

By Charlie Brumbaugh

Antarctica with its diverse conditions such as severe cold, high winds, rock and ice structure and limited explosives available posed many obstacles. This paper will give an overall view of the methods used to overcome these obstacles on a daily basis on the highest, driest, coldest continent on earth.

Jan 1, 2000

By Laurance L. Oden

The Bureau of Mines is developing nickel catalysts for converting synthesis gas derived from coal to synthetic natural gas. The present report describes the relationship between the composition of aluminum-nickel alloys in the composition range NiAl3 to Ni2Al3 equilibrated at 840° C and the properties of catalysts obtained from them. Methanation activity was determined in the temperature range of 300° to 360° C in a flowing gas stream containing 1 pct CO, 8 pct H2, and the remainder He. One part per million of H2S was added to the gas stream at 400° C to evaluate the susceptibility of catalysts to sulfur poisoning. The total surface area was measured by the adsorption of nitrogen at liquid nitrogen temperature, and the active surface area was measured by the adsorption of hydrogen at room temperature. Total surface area and active surface area were found to increase with increasing proportion of aluminum-saturated Ni2Al3 in the precursor alloy, but methanation activity and resistance to poisoning by H2S were nearly constant. However, the methanation activity of the catalyst prepared from stoichiometric Ni2Al3 was less than half that of the other catalysts.

Jan 1, 1978