Search Documents

By Henry Hebley

IN recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and clean-ing of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal.

Jan 1, 1933

By R. J. Schilthuis, T. V. Moore

In a previous paper,' the results of some experimental work on the measurement of slippage in the flow of oil and gas mixtures through vertical pipes were presented. The data obtained were correlated and equations were deduced from which the performance of the experimental gas-lift could be predicted with reasonable accuracy. However, attempts to apply the equations to the calculation of pressure drops in actual flowing wells yielded erroneous results. At the time the results of the experimental work were published, no satisfactory explanation could be offered for the failure of the empirical equations to express properly the performance of wells. However, recent work has led to the development of a new hypothesis which presupposes certain conditions affecting the flow of oil and gas in wells. When the proposed equations are corrected to allow for these conditions, an agreement between the observed and calculated performance of the actual wells is obtained which in most cases is quite satisfactory, although it is subject to certain limitations. In this paper, the method of calculating the pressure drop in actual wells is considered, and the application of the method to the design of tubing is discussed. (For nomenclature used in this discussion, see Table 1.) Factors Affecting Slippage and Efficiency At the outset, a few of the principle factors affecting slippage and efficiency in the gas-lift discussed in the previous paper will be reviewed. In the flow of the mixture of oil and gas in a vertical pipe, slippage is the phenomenon of gas moving upward with a. linear velocity greater than that of the oil. Under steady conditions, if given quantities of oil and gas enter the tubing per unit of time, the same quantities of oil and gas per unit time must, on the average, pass every section of the tubing; otherwise, there would be accumulation or depletion of the oil or gas at some sections, and the flow would be unsteady. Therefore, if the gas is to flow at a greater linear velocity than that of the liquid,

Jan 1, 1933

By Dr. O’Neil Thomas J., Donald W. Gentry

"There are two characters to the value of mining properties-one mine may have a value, owing to its real intrinsic worth; an- other (having no intrinsic value) may have a value by being so situated as to harass the working of the really valuable mine-in mining camps one is looked upon as much of ligitimate enterprise as the other.'' -Victor Clement to Simeon Reed, Wardner, Jan. 11, 1890, Reed Mss. APPROACHES TO VALUATION Value and costs are two terms basic to financial analysis which cause, perhaps, the greatest amount of misunderstanding in mine valuation studies. When discussing the value of an asset or the costs of producing a product, it is absolutely essential that the speaker define the terms being used. There are many types of value and many categories of costs. Without specific accompanying definitions, value and cost data are not very meaningful. Value refers to a measure of the desirability of ownership of property. Some of the types of value which might be encountered in a mine valuation study are: 1) Market value 2) Full cash value 3) Salvage value 4) Replacement value 5) Capitalized value 6) Book value 7) Assessed value 8) Insured value Each of these has a specific meaning which can be applied to determine a monetary amount in a specific situation. The major item of interest here is the broader question of "what is the value of the mine?" or "what is the mine worth?" In this case, we are speaking of market value. Market value is the value (price) established in a public market by ex- changes between a willing buyer and a willing seller when neither is under duress to complete the transaction. Market value fluctuates with the degree of willingness of the buyer and seller and with the conditions of the sale. The use of the term market suggests the idea of barter. When numerous sales occur on a market, the

Jan 1, 1984

By J. L. Rodda

The desirability of a uniformly sized abrasive for metallographic polishing has probably been recognized in a general way for a long time. Certainly all metallographers have recognized the damage that can be done to a polished surface by a piece of grit, especially if one of the softer metals, such as zinc or aluminum, is being polished. It is to be doubted, however, whether many metallographers have had any adequate idea of the particle size of the abrasives they were using or of the range of sizes encountered in any given grade of abrasive. At any rate, the descriptions of abrasives for metallographic work found in the literature are generally very meager. It was with the idea of securing an abrasive with a limited range of particle size that a study of this problem was commenced. Commercial abrasives, even when recommended for metallographic work, are made up of particles of varying sizes. One such abrasive contains some particles so fine that they remain in suspension for days and other particles so coarse that they settle at the rate of 3 in. per minute. It is evident that the coarsest particles are over 100 times the diameter of the smallest ones, or over 1,000,000 times the volume. The hopelessness of avoiding scratches under these conditions is evident. Vanderwiltl has described a laboratory method for grading abrasives in which the elutriator is used. Le Chatelier's method, described by Goereq2 also makes use of an elutriator. However, the elutriator is too slow for this purpose and requires too delicate a control for the range of sizes desired. The method of stirring up the abrasive in water, allowing it to settle for a given time, then drawing a measured depth off the top of the suspension, has been finally adopted as the simplest procedure. The largest particle in a given portion is then determined by Stokes' law:3

Jan 1, 1932

By Frank M. Brewster

The handling of congealing oils and paraffin is a serious problem in the Appalachian fields, particularly because the small amount of oil produced per well makes the removing of paraffin a very costly operation per barrel. Few operators realize or have any means of knowing just how much production is lost on account of paraffin depositing over the face of the sand and plugging the pores of the sand; but where paraffin has been removed the production increases indicate that this loss has been considerable. Many operators believe that paraffining is confined to the tubing and pumping equipment, but it is evident that the most serious damage occurs on the face of the sand and a short distance back in the pores. This paper is an attempt to disseminate information on methods and processes in use in the Eastern fields for combatting losses of production and operating difficulties caused by deposition of paraffin in the pores, on the walls, on the tubing and on other pumping equipment. Mills1 covers this subject so thoroughly that excerpts, abstracts and quotations from his work have been used freely in this paper. Nature oF Paraffin Mills states: "The so-called paraffin that collects in oil wells, and in the pores of the producing sands immediately around the wells, is generally made up of amorphous wax or uncracked paraffin, asphalt, or other gummy hydrocarbons mixed with more or less water, oil and inorganic silt. Some of the samples of this paraffin collected from oil wells in different fields and examined by the Bureau of Mines contains as much as 20 per cent. by weight of water and inorganic silt, whereas other samples are composed entirely of waxy hydrocarbons and oil. The inorganic silt accompanying this 'paraffin' is mostly fine sand, clayey materials, common salt and finely disseminated precipitates of calcium and magnesium carbonates. Sulfates of calcium, barium and strontium are less common constituents of paraffin.

Jan 1, 1928

By Henry Fay

THE erosion of guns is a complex problem which can be solved only by a detailed study of all the factors involved. In the present paper it is proposed to submit the results of observations and experiments which have extended over several years. Certain facts have been established and preliminary reports have been published.' Conclusions have been reached since then which, it is believed, are worth presenting for the purpose of promoting discussion, and with the hope that ultimately the whole truth will be known. The particular phase of the problem which will be presented here is the hardening of the inner surface of the gun tube. It has been known for a long time that after firing a large caliber gun for some time, the surface of the metal becomes hard and brittle, cracks, and wears away.2 The character of this phenomenon may be learned by an examination of some results which are typical, obtained from a detailed study of a 12-in. gun. The gun was trepanned and rings representing various sections of the gun were cut out for examination. The first ring represented the metal at the muzzle end, and the other rings were removed at approximately 120, 240, 325 and 337 in., respectively, toward the breech end. The appearance of the surface of the metal in the different sections is shown in Fig. 1. The greatest amount of wear and maximum amount of hard surface layer was found in section marked E, which is nearest the powder chamber and at the beginning of the rifling; the maximum amount of cracking in D; the maximum amount of copper deposition in C. Section B showed heat cracks on both lands and grooves, and section A showed heat cracks on the driving edge of the lands only. There was much flow of metal in both sections E and D, and there was progressively less effect noticeable toward the muzzle end. The polished cross-section of these same pieces is shown in Fig. 2. The

Jan 12, 1916

By N. H. Emmons

The work of a consulting engineer or manager, when controlling mining-operations, requires that he have all the information concerning the mine in as concise a form as possible, and as the ore-reserves and their depletion and enlargement are the vital points to be studied, it is well to have the records kept up to date and in some convenient form. The present paper describes a method adopted by me, which shows in a very clear manner the ore-reserves in a mine. The case illustrated is that of a vein near enough to the vertical for the vertical elevation of the mine to be the main working-map. A flat ore-body would be represented on a similar plat, but instead of the horizontal thickness of the vein being shown in the circles, the vertical thickness would be inserted. Fig. 1 represents an ideal longitudinal elevation of a mine, plotted in the ordinary way, using 100-ft. blocks and section-lines. In a mine where the block-numbers are posted by the engineer underground, the system of keeping the ore-tonnages extracted from the different blocks is easily maintained, and the actual tonnages of ore extracted can be kept so that the surveyor can have a check on his estim'ate from time to time. The ore-reserve sheet, Fig. 2, should be the same size as the map it is to accompany. Each square is used for the description of the ore-reserve in the block it corresponds to on the elevation. Where the section-lines cross the levels a circle is drawn, in which are written the midths of ore at that point, these widths being used in the calculations of each block cornering in the circle. It has been found convenient to show the figures in black in the lower half of the circle when the actual widths of ore are known, and when it is necessary to make up the figures of probable ore, as at the time of making

Jan 1, 1913

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By Robert A. Cook

Among the new devices for cheapening the cost of material entering into the manufacture of iron is the mechanical drawing of coke, by which the coke from bee-hive ovens is extracted with a minimum of manual labor. About twenty years ago, an ordinary plate-conveyer was put in use at the plant of bee-hive coke-ovens owned by the firm of Bell Bros. & Co., near Middlesboro, England. This conveyer ran close along the front of the ovens, and carried the coke to the cars. The ovens were drawn by hand, and a very great saving in cost was secured, as one man could draw and clean out twice as many ovens after the conveyer was put in use—he having no forking to do, and the coke being carried away as fast as it was drawn to the mouth of the oven. The next step was further to eliminate hand-labor as far as possible; and Mr. Thomas Smith of the Thorncliffe Iron Works, near Sheffield, patented in 1891 the machine for drawing coke which I here describe. This machine, the outcome of several years of experimenting, has now been in successful use since 1891, and there are between twenty and thirty of them in operation at present, and others building. The machine, as may be seen from Figs. 1 and 2, consists of a wedge-shaped shovel of proper width and thickness, connected with a steel rack of sufficient length to reach the back of the oven. The rack is supported by rolls, and guided by a device operated by a hand-wheel, which directs the shovel in the oven. The rack is driven by a pinion on a vertical shaft carrying a bevel-gear on the upper end. This bevel-gear is driven by another on the engine-shaft. The engine is single-cylinder, with reversible gear; and engine and machine are mounted on a truck, which is propelled

Jan 1, 1897

By Thomas Read

SUMMARY THE cost of labor turnover in industry is so large as to justify the adoption of almost any means to bring about its reduction. Intensive study has shown that faulty methods of hiring and discharging men is the most important factor in labor turnover. Complete control over hiring and discharging by the foreman is a relic of outgrown industrial conditions; centralized hiring permits this work to be put on a scientific basis and also does away with many serious evils that cannot otherwise be reached. Centralized hiring does not impair the authority of the foreman; he hires his men from the employment office and discharges them back to it, instead of from and to the street. The employment manager, being a direct representative of the employer, tends to restore the former relation of direct intercourse between employee and employer that was helpful in avoiding friction between them. Being a specialist, he is able to bring special knowledge and skill to bear upon the task of selling employment in his concern to desirable workmen; lie is also able to give the foreign workman the special attention he requires. Employment managers have been used for the past few years by a number of large organizations, a few of which are engaged in the mining and metallurgical industries. They have invariably reduced labor turnover, in some cases to as little as one-tenth of what it had been. So great a reduction is due in part to other changes made in the light of the data made available by scientific study of the labor problem. In my former paper on personnel work1 I advocated the more general use of the employment manager in mining and metallurgical enterprises as a means of reducing labor turnover. The form of organization recommended seems not be to understood by all, and I have requested the privilege of explaining it at greater length, since it is perhaps the most important factor of all in personnel work, and has a vital influence on the cost sheet of every industrial enterprise.

Jan 2, 1918

By E. Stansfield

IT. has long been known that coal is unstable and oxidizes in air, even at ordinary atmospheric temperatures; also, that such oxidation affects the analysis of coal. Nevertheless little or no precaution is taken to prevent oxidation in the ordinary methods of analysis, and the possibility of error due to oxidation is sometimes ignored even in researches on coal. Although the general nature of coal oxidation is well known, and many workers have made careful studies of the rate of oxidation of different types of coal exposed to oxygen at different temperatures, yet the amount of oxidation coals undergo in the ordinary process of analysis, and its influence on the determined analysis, is not well known, and the published data are widely scattered through the literature. This paper is a collec-tion, from this laboratory, of data that bear on the subject, together with a brief summary of three methods employed here to evaluate the oxidizabil-ity of coal. The post-Carboniferous coals of Alberta range all the way from anthracite down to lignite. As some of them are notably susceptible to oxidation, the necessity for care was early forced upon our attention, and oxidation has been reduced either by the removal of air with a vacuum pump or by the displacement of air with natural gas (methane). The two routine analytical operations most liable to involve oxidation are the preliminary, partial drying of the crushed coal (called air-drying) and the determination of moisture. The first is a prolonged operation on coarse coal at ordinary temperatures, and the second a short treatment on powdered coal at higher temperatures. Oxidation also occurs in coal samples stored in ordinary sample bottles. In order to gain information for this study, determinations were recently carried out on the same samples in air, in natural gas, and in vacuo. Sixteen coals were tested; three would be classed in the United States as coking bituminous coals, two as noncoking, nonslacking, bituminous coals, and the rest as subbituminous. Table 1 gives typical analyses of these coals as mined.

Jan 1, 1934

By W. A. Lang, K. C. Gilbart, E. Stansfield

It has long been known that coal is unstable and oxidizes in air, even at ordinary atmospheric temperatures; also, that such oxidation affects the analysis of coal. Nevertheless little or no precaution is taken to prevent oxidation in the ordinary methods of analysis, and the possibility of error due to oxidation is sometimes ignored even in researches on coal. Although the general nature of coal oxidation is well known, and many workers have made careful studies of the rate of oxidation of different types of coal exposed to oxygen at different temperatures, yet the amount of oxidation coals undergo in the ordinary process of analysis, and its influence on the determined analysis, is not well known, and the published data are widely scattered through the literature. This paper is a collection, from this laboratory, of data that bear on the subject, together with a brief summary of three methods employed here to evaluate the oxidizabil-ity of coal. The post-Carboniferous coals of Alberta range all the way from anthracite down to lignite. As some of them are notably susceptible to oxidation, the necessity for care was early forced upon our attention, and oxidation has been reduced either by the removal of air with a vacuum pump or by the displacement of air with natural gas (methane). The two routine analytical operations most liable to involve oxidation are the preliminary, partial drying of the crushed coal (called air-drying) and the determination of moisture. The first is a prolonged operation on coarse coal at ordinary temperatures, and the second a short treatment on powdered coal at higher temperatures. Oxidation also occurs in coal samples stored in ordinary sample bottles. In order to gain information for this study, determinations were recently carried out on the same samples in air, in natural gas, and in vacuo. Sixteen coals were tested; three would be classed in the United States as coking bituminous coals, two as noncoking, nonslacking, bituminous coals, and the rest as subbituminous. Table 1 gives typical analyses of these coals as mined.

Jan 1, 1934

By Fred E. Wright

In a recent paper1 a detailed discussion is given of the possibilities of using polarized light in the examination of opaque substances. The factors underlying the problem are there treated from the viewpoint of the electromagnetic theory of light and the presentation is necessarily mathematical in form. The practical methods resulting from the discussion are, however, relatively simple and promise to be of value in the determination of certain ores and metals when studied in reflected light under the microscope. The results of the theoretical investigation referred to may be summarized by stating that in general the optical constants, such as refractive indices and absorption indices, cannot be satisfactorily ascertained on small, random, polished sections; that the use of polarized light enables the observer ordinarily to determine whether the crystal plate is iso-tropic or anisotropic, and also to ascertain the degree of anisotropism; that for this purpose methods based either on the contrast in intensity between the two reflected components of non-polarized light, or on the amount of rotation of the plane of polarization, on reflection, of vertically incident, plane-polarized light, may be employed; that methods based on the phase difference between the two reflected components are in general of little value because of the small differences in phase which ordinarily result for a relatively large change in birefringence or biabsorption. The measurement of the optical properties of transparent minerals, even in minute irregular grains, is a simple task with modern petrographic microscope methods and is accomplished by petrologists as part of their ordinary routine work. But the determination of the optical constants of opaque substances is difficult and is rarely attempted; all observations are necessarily made in reflected light and are restricted commonly to the determination of color, of hardness, of the character of crystallization, and of the behavior of the mineral or metal plate toward reagents and abrasives. With practice, the observer becomes expert in recognizing details of this kind and determines with a high degree of certainty the different

Jan 1, 1920

By E. B. Harden, J. H. Harden

The practical use to which topographical models or relief-maps have been put, has within the last few years taken a wider range. They are rapidly coming into favor for other than purely scientific purposes, and their value for illustration and instruction is being more fully appreciated. Topographical maps; representing by contour-curve lines the elevations and depressions of the earth's surface, are now demanded in engineering work of nearly every description, and afford a ready means of bringing out the configuration of the country in a simple manner. A beautiful example of recent topographical mapping is seen in the seventeen sheets just issued by the Geological Survey of New Jersey. By reason of the inability of unskilled persons to understand the nature of a topographical map, it is sometimes necessary to con struct the same in relief, with the rivers, canals, railroads, etc., delin eated upon it. With the aid of such a map, problems in engineer ing science which would otherwise require expert assistance to explain them, are reduced to a simple and understandable form. Relief-maps are also of value to the geologist in working out the geological structure. To the instructor they present the most ready and efficient means of imparting clear and accurate knowledge of topography and kindred subjects. To the lawyer they are invalua ble in enabling him to bring into the court-room a representation of a part of the country with all its features accurately shown, to ex plain to the court and jury the special points about which litigation is pending and which would otherwise require long and laborious description. The application of the topographical map to business purposes is shown in a relief constructed by the writers for the Cumberland Valley Railroad Company and used by that company in the various ways of calling attention to the desirability of its route. This model is based partly on actual survey and partly on sketch topography. The horizontal scale is ,%, the vertical 1/19,200 of

Jan 1, 1888

By H. M. Howe

One of the little electric-resistance magnesia crucible-furnaces which I designed for the metallurgical laboratory of the School of Mines of Columbia University is shown, in vertical section, of full natural size, in Fig. 1. The furnace itself consists of two semi-cylinders of magnesia, A A, with a cover of magnesia, B B, and a stopper, C, also of magnesia, which is perforated to admit the leads x, y, of a thermo-electric couple. The furnace is heated by the spiral of platinum wire, D D (entering and departing by the openings I and K), through which a current of any desired strength is passed, bringing it to incandescence, and to ally temperature, not above the melting-point of platinum, which may be desired. The crucible E, actually used in this furnace, is also of magnesia. I have heard of some unsuccessful attempts with furuaces of this general class, and have attributed these failures to the use of siliceous materials for the furnace-walls. Of course such a result is what we should expect, since the silica mould readily be electrolysed by the current, and the resultant silicon would alloy with platinum ; but the little magnesia furnace here clescribed seems to be wholly free from this objection. It has been used in my laboratory for some months, and temperatures, up to 1100° C, hare been developed in it over considerable periods of time—indeed, it has been held near 1400" C. for about two hours—without indication, thus far, of any deterioration of the platinum. In the section shown, F F are a pair of steel disks, bound together, but separated by the inverted thermo-junction, N, of the thermo-electric pyrometer. This arrangement permits the observation and record of retardations in the heating and cooling of F F—in other words, the determinations of the cooling curves of steel—a purpose for which the furnace has been used, thus far, more frequently than in the determination of meltingpoints. For the latter operation, however, it is also suitable.

Jan 1, 1902

By H. M. Merry

The graphic methods and records described in this article have been developed, with satisfactory results, for the use of executives of the Chino Copper Co., in Hurley, N. Mex. Particular attention is directed to the use of large wall-charts, the quick reference display of large charts, the scale notation of metallurgical charts shown in Pig. 3, and the inclusion of mesh extraction on screen analysis diagrams. To properly comprehend the operation and metallurgical results from a concentrating plant, a daily record of essential data is kept, usually involving the dry weight of ore milled or treated, dry weight of concentrate or metal produced, assay values of heading, assay values of tailing, assay values of concentrate, and percentage of extraction or recovery. In addition it is often necessary to record moisture, pulp density, or dilution, percentage of weight of oils and reagents employed; screen analyses of grinding conditions, oversize, etc.; assay values of non-valuable or interfering substances; cost data; and such special information as may be required. GRaphic Presentation . Close analysis is necessary of a daily operation involving such a number of factors, the relation and influence of which may be of great importance in the treatment scheme. When the analysis is made from a numerical tabulation, the chance for one or more obscure, but perhaps important, factors to escape notice is considerable, therefore the need for an accurate, readily digestible presentation of metallurgical data is obvious.. Graphic records of milling operations are frequently used, but owing to the wide range of magnitude and values, and the number of factors involved, the customary practice of assigning different values to the same ordinates, as in Fig. 1, results in a complex and intricate record which makes little appeal to a busy operating official. The methods shown in Figs. 2 and 3 are devised to display such data in a clear and legible manner, without confusion.

Jan 1, 1920

By John Birkinbine

An item of considerable importance to the producers of pig-iron is the disposition of the slag or cinder from the blast-furnace; and various plans have been adopted at different works to care for the rapid accumulation of this generally waste material. The charge per ton of iron made which must be allowed for the care of cinder is sufficient in times of business depression to give plants having facilities for disposing of their slags an advantage over others less favorably arranged, and to allow iron to be produced profitably in the one case and prevent a profit in the other. The varied methods employed and the means of conveyance utilized need not be detailed. It is sufficient to say that the large outputs of American blast-furnaces, and consequent rapidly augmenting dump-piles, have brought into general favor the use of cars carrying the slag in a liquid condition. The advantages of this method are the prompt removal of the slag, the reduced space occupied by the dump-piles, and the facility of converting the slag into such forms for use as may be desired. The progress in iron-manufactlire is also marked by a more general adoption of methods by which molten metal is carried in vessels away from the point of its production; and, anticipating the prospective advance in pig-iron manufacture, it does not seem unreasonable to prophesy the early abolition of casting-houses at blastfurnaces, particularly where several are grouped together; or the casting of steel ingots away from the converters or furnaces. In some large blast-furnace plants, the iron is carried molten from the blast-furnaces to the converters or other furnaces. Even where it is cast into pigs, casting-sheds removed from the immediate vicinity of the furnace-stack would, perhaps, be superior to casting in beds in front of the furnaces. The idea of casting-sheds appears to present the following advantages : 1st. The equipment of boilers, hot-ovens, and blowing-machinery could be closely grouped around the blast-furnace stacks, permitting

Jan 1, 1887

By Roy E. Dickerson, W. M. O Connor

The production of crude petroleum of the Bacuranao field, Cuba, fell off rapidly because no new wells Mere drilled. In December 1938, the total was 15 bbl. per day. The estimated average from this serpentine field for the year is 20 bbl. per day. The Motembo area produced an estimated average of 160 bbl. per day. Production in July was 215,946 gal of gasoline, or 165 bbl. per day. In August production was higher because a new well in the concession, the Luisa Marcela, produced 189 drums the first day and required pit storage. The Atlantic Refining Company of Cuba started a deep test upon a long, narrow, surface-defined anticline 3 km. south of Remedios, a town on the north coastal plain of Santa Clara province, in December 1938. The Atlantic Refining Co. is doing extensive seismograph arid gravity-meter work in Matanzas arid Santa Clara provinces. The Shell company was rigging for a deep test in western Havana province at a location about 2 km. west of the town San Antonio dc los Banos New Petroleum Law More serious attention was given by some of the major oil companies to the development of petroleum in Cuba as a, result of the passage of a Petroleum Law ill that country on May 9, 1938. Under the old mining lam of Cuba, which gave no special treatment to petroleum, the usual provisions giving reasonably satisfartory guarantees to encourage investmerit of foreign capital were either entirely lacking or were 30 ambiguously expressed as to require legislative action. Under the new law, Government royalty is fixed at 10 per cent with the provision that it will be reduced to 9 per cent on crude petroleum that is refined in Cuba. Royalty to the surface owner is 1 per cent. A surface tax on a sliding scale from 10¢ to 406 per hectare per year is applicable to all exploitation concessions granted under the law or adapted to its provisions. So export tax is payable upon petroleum. Stability of taxation

Jan 1, 1939

By W. M. O Connor, Roy E. Dickerson

The production of crude petroleum of the Bacuranao field, Cuba, fell off rapidly because no new wells Mere drilled. In December 1938, the total was 15 bbl. per day. The estimated average from this serpentine field for the year is 20 bbl. per day. The Motembo area produced an estimated average of 160 bbl. per day. Production in July was 215,946 gal of gasoline, or 165 bbl. per day. In August production was higher because a new well in the concession, the Luisa Marcela, produced 189 drums the first day and required pit storage. The Atlantic Refining Company of Cuba started a deep test upon a long, narrow, surface-defined anticline 3 km. south of Remedios, a town on the north coastal plain of Santa Clara province, in December 1938. The Atlantic Refining Co. is doing extensive seismograph arid gravity-meter work in Matanzas arid Santa Clara provinces. The Shell company was rigging for a deep test in western Havana province at a location about 2 km. west of the town San Antonio dc los Banos New Petroleum Law More serious attention was given by some of the major oil companies to the development of petroleum in Cuba as a, result of the passage of a Petroleum Law ill that country on May 9, 1938. Under the old mining lam of Cuba, which gave no special treatment to petroleum, the usual provisions giving reasonably satisfartory guarantees to encourage investmerit of foreign capital were either entirely lacking or were 30 ambiguously expressed as to require legislative action. Under the new law, Government royalty is fixed at 10 per cent with the provision that it will be reduced to 9 per cent on crude petroleum that is refined in Cuba. Royalty to the surface owner is 1 per cent. A surface tax on a sliding scale from 10¢ to 406 per hectare per year is applicable to all exploitation concessions granted under the law or adapted to its provisions. So export tax is payable upon petroleum. Stability of taxation

Jan 1, 1939