Search Documents

By Carl Henrich

While the size of the blast-furnaces used for smelting leadand copper-ores has constantly increased, during late years, the manner of removing the slag from the furnace to the slag-dump has (until quite recently, at least) practically remained the same. The only appliance in practical use has been the two-wheeled slag-pot, holding about 300 to 400 pounds of slag, or as much as one man could manage to pull or push on a smooth, hard surface. When these slag-pots on wheels were first introduced, the daily capacity of a lead or copper blast-furnace hardly reached 30 tons of smelting-charge. With furnaces of this size, and even when the capacity had been doubled, this kind of slag-pot answered well enough. All the improvements made were in the construction of these pots and not in an increase of their size, which was limited by the weight which one man could handle. But the size of the furnace went on increasing. The daily consumption of one furnace rose gradually to 75 tons, 100 tons, and even more. The writer had occasion to construct some of these furnaces, which, in their day, were among the largest, if not the largest, of the water-jacketed kind then in existence. A water-jacketed furnace will always smelt more in the same time than a furnace with brick walls. Already, in those days, the slag-removal from these enlarged furnaces received due attention by the writer. The removal of 60 tons of slag in 24 hours, in pots holding only 300 pounds each, will require 400 pots to be filled in 24 hours; and when the amount.of slag increases to 90 tons, 600 pots will be required. That is to say, in the last case, 25 pots in each hour, or 1 pot each 24 minutes, will have to be put under the slagspout, filled, pulled away, and replaced with another. This will involve too much hurry for any degree of comfort, convenience

Jan 1, 1896

By C. H. Mathewson, Robert Maddin, W. R. Hibbard

A SATISFACTORY mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.1 Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.3 EXPERIMENTAL PROCEDURE Half inch rods of alpha brass (nominally 70 pct Cu, 30 pct Zn) * were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.' In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pct nitric acid solution. The back-reflection Laue technique as described by Greninger5 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buerger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1948

By Robert T. Howard, Morris Cohen

IT has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkin1 has shown that the compositions of two coexisting phases in a a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanalysis.3 Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantitative way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of, this research could not be treated satisfactorily by other quantitative tools, such as specific volume,4 magnetic,5 dilatometric,6 electrical resistance7 or x-ray measurements.8 It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. LITERATURE SURVEY Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1947

By Ira B. Joralemon

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

By Ira B. Joralemon

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

By Ira B. Joralemon

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

By C. A. Stetefeldt

The iron-ore deposits worked by this Company occur in lenses 200 to 1000 feet long and 5 to 80 feet wide, and stand at an angle of from 65' to 75, with a vertical height of 250 to 500 feet, other lenses occurring below. A number of the deposits were first worked as open pits, which in some cases were carried to the depth of 150 feet, when, owing to the weakness of the walls, underground mining was adopted. While the ore was being removed from the open pit, shafts mere in several instances sunk into the foot-wall, the intention being to mine the ore with breast-stopes of an approximate height of 20 feet, followed by underhand-stopes of the same height, leaving floors between of the necessary thickness to support the walls, or to effect the removal of the ore by means of what is known as the stall system. As the work progressed, however, it was found that the walls (which are of chlorite) were too weak to permit the working of breast-stopes 20 feet high, there being frequent heavy falls of ground from the hanging and, in some instances, from the foot. The plan of following breast-stopes with underhand-stopes was, therefore, abandoned. By working breast-stopes only, but little more than one-half of the ore could be removed, and that only at an excessive cost, the ore being so hard that power-drills with 3 1/8-inch pistons . and 6-inch stroke, working under 60 pounds of compressed air, are able to drill but 8 feet in ten hours as a yearly average, while from 6 inches to 2 feet is a common result of ten hours' drilling. It was plain that some other system of mining must be adopted, and it was proposed to sink by levels of 75 feet, carrying in the cross-cuts from the shafts and working out the ore each way from the shaft from foot to hanging, and from 15 to 20 feet in height. When this has been done, drift-sets consisting of caps and legs are set up the whole length of the opening and connected with the cross-cut; the necessary openings for ladder-ways and chutes or mills are timbered from

Jan 1, 1893

By W. A. Ver Wiebe

The year 1938, with a production of 58,784,250 bbl. from 18,790 wells shows a slight recession from the high peak of oil production reached the previous year, when slightly over 68 million barrels of oil was marketed. The previous high peak had been reached in 1917 with a total of 45,451,000 bbl. Another still earlier peak was reached in 1904, during which year slightly less than 5 million barrels was produced and sold. The production of gas, on the other hand, probably reached a new peak during 1938 with a total of over 60 billion cubic feet. This peak, however, was not the highest peak, for during the year 1908 over 80 billion cubic feet was produced. Between these two high peaks the production dropped down to 16 billion cubic feet in the year 1921. The number of wells drilled during the year totals 1569. This figure is somewhat lower than the figure given in several trade journals because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly three-fourths (or 1107) of the total number of wells were completed as commercial oil wells (915 in western and 192 wells in eastern Kansas). The commercial gas wells completed number 50, of which 4 are in eastern Kansas and 46 in western Kansas. The remaining 412 completions include 130 dry holes in eastern and 282 dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year accounted for 70,000 bbl. of new oil for eastern and 1,220,000 bbl. of new oil for western Kansas. It is interesting to note in this connection that the number of wells completed in the state rose gradualIy to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918 when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak in 1937, the low point was reached during 1931, with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a new area whether it should be called a new pool or a long extension of an

Jan 1, 1939

By F. S. Sinnatt

This paper is the outcome of an extended investigation carried out in association with Dr. L. Slater. The inquiry had been continued in various directions and a number of results are quoted from an investigation recently completed by S. H. Jenkins. In projecting the work some five years ago, the author had in view a general attack on the problem of the spontaneous combustion of coal from an angle that had received little attention. The basic idea was to obtain a "slow motion study" of the active combustion of coal. This included an examination of the conditions prevailing in a mass of coal at the moment when active combustion ceases. It was thought that, if the factors governing the extinction of combustion in coal could be definitely established, it might offer an explanation of the manner in which the spontaneous combustion of coal originates. The inquiry arose from a detailed study of the properties of fusain that the author began in 1918. Fusain seemed to possess characteristics quite distinct from the coal with which it was associated, for if it were collected into a heap and one portion were heated by a small flame the combustion would traverse the whole mass. This combustion was not accompanied by smoke and passed slowly through the heap of material. Later, it was found that coals, including anthracites, would behave in a similar manner provided they were in the form of powder and that the particles were smaller than a certain size. The limiting size of particles is a definite characteristic of the coals investigated. In view of the fact that fusain exists with coal in a state that enables it to undergo this particular form of combustion, it must be assumed, sometimes, to play a definite part in the spontaneous combustion of coal in the goaf (waste). Tables 1 and 2 contain the analyses of samples of dust collected from a mine and from a dust collector. Some idea of the degree of fineness of the particles of fusain may be obtained from a study of the analyses of the dust from the dust collector; 80 per cent. of the dust would pass through a 200-mesh screen while the fusain was concentrated in the finest dust. The material that passed through a 90-mesh screen contained 54 per cent. of fusain while that between a 30- and a 90-mesh only con-

Jan 1, 1925

By W. A. Ver Wiebe

The year 1938, with a production of 58,784,250 bbl. from 18,790 wells shows a slight recession from the high peak of oil production reached the previous year, when slightly over 68 million barrels of oil was marketed. The previous high peak had been reached in 1917 with a total of 45,451,000 bbl. Another still earlier peak was reached in 1904, during which year slightly less than 5 million barrels was produced and sold. The production of gas, on the other hand, probably reached a new peak during 1938 with a total of over 60 billion cubic feet. This peak, however, was not the highest peak, for during the year 1908 over 80 billion cubic feet was produced. Between these two high peaks the production dropped down to 16 billion cubic feet in the year 1921. The number of wells drilled during the year totals 1569. This figure is somewhat lower than the figure given in several trade journals because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly three-fourths (or 1107) of the total number of wells were completed as commercial oil wells (915 in western and 192 wells in eastern Kansas). The commercial gas wells completed number 50, of which 4 are in eastern Kansas and 46 in western Kansas. The remaining 412 completions include 130 dry holes in eastern and 282 dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year accounted for 70,000 bbl. of new oil for eastern and 1,220,000 bbl. of new oil for western Kansas. It is interesting to note in this connection that the number of wells completed in the state rose gradualIy to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918 when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak in 1937, the low point was reached during 1931, with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a new area whether it should be called a new pool or a long extension of an

Jan 1, 1939

By A. E. Martin, Gerhard Derge

IF the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of diffusion, and electrical conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented as Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags of the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. REVIEW of LITERATURE In 1906 Aiken1 obtained a patent for a continuous process of producing iron electrolytically by passing a direct current through a bath of FeO-SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the, Institute itself has five major awards to make annually for excellence in technical papers, as follows The Robert W. Hunt Medal and Prize, The J E Johnson, Jr Award, The Lewisohn Platinum Prize to senior members, and the James Douglas Medal ROBERT W HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules 1 The award shall consist of two prizes, first of a gold medal, second of a sum of money, a certificate to accompany each prize The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee consider¬ing the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improve¬ment of production and quality of material. 3 A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval 4 The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute 5 The recipient of the award shall be designated "The Hunt Medallist " This prize is administered by the Iron and Steel Committee

Jan 1, 1923

By A. Andreas

New Mexico, after several years as the sixth ranking oil-producing state, was surpassed by Illinois and for 1939 ranks seventh in the United States. Oil production for 1939 was 36,746,840 bbl. Production for 1938 was 35,510,176 bbl., a gain of 0.033 per cent. Production for the year would have been greater had there been a pipe-line outlet for the Vacuum field. The complete shutdown during the latter part of August covering a period of 15 days meant a production loss of over 1,500,000 bbl. of oil. Daily production allowable as set by the Oil Conservation Commission has followed very closely the recommendations of the Bureau of Mines. It has been found that the recommended allowables as quoted by the Bureau of Mines do not always reflect the actual demand, as there is a considerable lag hetween the recommended amounts and the current demands. During the year the various operating companies have done considerable remedial work in setting packers to reduce the gas-oil ratios in the various fields. Six new fields were discovered in New Mexico during 1939; three in Lea County, two in Eddy County and one in Chaves County. In the early part of 1939 a committee composed of the various engineers and geologists recommended subdividing the old Artesia area into various producing pools. This division was accepted, therefore the total number of producing fields in New Mexico is considerably greater than the number of fields in 1938, but does not represent new fields discovered during the year. The southeastern area continues to he the largest producer of oil. During the year 2,716,551 bbl. were produced in Eddy County and 33,690,996 bbl. in Lea County. Total production ill the northwestern part of the state, which includes San ,Juan and McKinley Counties, was 338,293 bbl. At the beginning of the year the daily average nonmarginal well allowable for Lea County was 48 bbl. At the close of the year it was 49 bbl. The daily average production for the year was 97,313 bbl. During the year, 659 wells were drilled in the state, of which 565 were producing oil wells, 15 gas wells, 6 carbon dioxide gas wells and 73 dry holes. Summarized at meeting; manuscript received at the office of the Institute March 18, 1940. * State Geologist, member of New Mexico Oil Conservation Commission, Santa Fe, New Mexico.

Jan 1, 1940

By A. Andreas

New Mexico, after several years as the sixth ranking oil-producing state, was surpassed by Illinois and for 1939 ranks seventh in the United States. Oil production for 1939 was 36,746,840 bbl. Production for 1938 was 35,510,176 bbl., a gain of 0.033 per cent. Production for the year would have been greater had there been a pipe-line outlet for the Vacuum field. The complete shutdown during the latter part of August covering a period of 15 days meant a production loss of over 1,500,000 bbl. of oil. Daily production allowable as set by the Oil Conservation Commission has followed very closely the recommendations of the Bureau of Mines. It has been found that the recommended allowables as quoted by the Bureau of Mines do not always reflect the actual demand, as there is a considerable lag hetween the recommended amounts and the current demands. During the year the various operating companies have done considerable remedial work in setting packers to reduce the gas-oil ratios in the various fields. Six new fields were discovered in New Mexico during 1939; three in Lea County, two in Eddy County and one in Chaves County. In the early part of 1939 a committee composed of the various engineers and geologists recommended subdividing the old Artesia area into various producing pools. This division was accepted, therefore the total number of producing fields in New Mexico is considerably greater than the number of fields in 1938, but does not represent new fields discovered during the year. The southeastern area continues to he the largest producer of oil. During the year 2,716,551 bbl. were produced in Eddy County and 33,690,996 bbl. in Lea County. Total production ill the northwestern part of the state, which includes San ,Juan and McKinley Counties, was 338,293 bbl. At the beginning of the year the daily average nonmarginal well allowable for Lea County was 48 bbl. At the close of the year it was 49 bbl. The daily average production for the year was 97,313 bbl. During the year, 659 wells were drilled in the state, of which 565 were producing oil wells, 15 gas wells, 6 carbon dioxide gas wells and 73 dry holes. Summarized at meeting; manuscript received at the office of the Institute March 18, 1940. * State Geologist, member of New Mexico Oil Conservation Commission, Santa Fe, New Mexico.

Jan 1, 1940

By B. S. Blakeney, E. P. Abrahamson II

The effect of the transition elements in binary solid-solution additions upon the recrystallization temperature of iron has been investigated. All these elements immediately raised the temperature, the majority having their greatest effect in less than 0.10 at. pct. A correlation is noted between the rate of change of recrystallization temperature with atomic percent solute and the electron configuration of the solute element. THE work of Abrahamson and rant' on binary chromium-base alloys indicated that a correspondence existed between the effect of each solute element on the brittle-to-ductile transition temperature of chromium and the ground-state electron configuration of the element added. This was felt to be a bonding phenomenon and would be expected to be observed in measurements of other properties involving the breaking or exchange of atomic bonds. From this work it was postulated that a like correspondence should be found for other properties of binary alloys, such as recrystallization. This study is an effort to check this postulation using binary solid-solution iron-base alloys. Previously, the majority of recrystallization studies were carried out on steels. However, Tammann2 investigated the recrystallization of iron as effected by Co, Ni, Si, Mn, Mo, and Cr and stated that elements with the same crystal structure at room temperature as iron appeared to be more effective in raising the recrystallization temperature. Austin, Luini, and Lindsay3 studied the effects of Ni, Cr, Mn, Co, Si, and Mo on cold rolling and annealing, but noted no trend. Abrahamson and rant,' in their work on the effect of both substitutional and interstitial elements upon the brittle-to-ductile transition of chromium, have shown that the outer electron configuration in the ground state of the solute element appears to be the prime determinant of the transition temperature. PROCEDURE All alloys were made using 99.95 + pct Fe with 0.02 wt pct 0, 0.004 pct C, and 0.001 pct N. All alloying elements were 99.9 + percent pure. Metal-lographically the alloys, out to at least 0.1 at. pct, appeared to be in solid solution. Though several published phase diagrams tend to dispute this.4 All alloys were arc melted six times and cast into square 400-g ingots under an argon atmosphere.

Jan 1, 1961

The following have been compiled from information furnished through the courtesy of Dr. W. P. Haynes, of London, and Mr. T. V. Grigorescu of Ploesti, Rumania. Gura Ocnitzei was the most active field during the year, furnishing 40 per cent of the production and 50 per cent of the drilling activity. Extensions to the west in this field were made both by Concordia and Romana Americana. In these new extensions the bulk of the production comes from the Drader member of the Dacian, with an average depth of 1300 m.; the underlying third Meotic at 1700 m. has not been developed yet. In Gura Ocnitzei east no new drilling has been done in 1933, but here declining pressures have led to the extensive use of gas-lift and pumps. Ochiuri saw some small drilling activity, but production declined. Two good wells were brought in by Unirea and Astra at the close of the year. Boldesti continued to be developed on a general plan by the four major companies interested. Production was from the Meotic, which in this dome has been penetrated for 356 m. Reserves have been estimated at about 63,000,000 bbl. An important discovery in this area was the bringing in of Credit Minier No. 1 Harsa to the east of the main field and producing from the Meotic. This well came in during October, 1932, and is now making 1400 barrels. In the Moreni Piscuri field only routine operations have been carried on. The prolific sands are now declining rapidly. Ceptura also saw only routine operations. In the Arcesti field development of the Meotic continues. Seven new wells were brought in during the year and ten were drilling at the close of 1930. The field produced over a million barrels for the first time during 1933. In the other fields only routine operations were carried on. A considerable increase in efficiency of operations was noted during the year. The average drilling time has been reduced, coring programs have been amplified, and much care has been taken in straight hole drilling. The Schlumberger electrical coring apparatus is extensively used. Electric-driven rotaries have been introduced at Gura Ocnitzei. The Moniteur du Pétrole Rouman reports that the index cost of drilling one meter, taking 1929 as a base of 100, has been reduced to 32 in 1933.

Jan 1, 1934

By M. L. Requa

In the fall of 1910, the Nevada Petroleum Co., operating in the Coal-inga field in California, determined to drill a number of wells with rotary tools, in order to prove conclusively the relative value of the rotary as compared with the standard rig. At that time, the rotary was but little known in California and its proposed introduction met with considerable criticism on the part of the operators and quiet opposition among the standard drilling crews. There were few men available who were competent to handle a rotary outfit, and these few had had but little experience in California fields. Machines as then built were much inferior to those now used, being lighter in construction and of a poorer quality of material. The shells encountered at depths between 1,700 and 2,000 ft. seemed to be too hard to permit of successful drilling, and at these depths the rig was changed over to standard tools and by them completed. Because of the heavy depreciation, the time lost in converting from rotary to standard, and the comparatively small profit, it was concluded that unless in the future there was some material improvement in rotary rigs, nothing would be gained by drilling with rotary tools upon this property. Little or no drilling has been done upon the property since that time, but in the meantime a large number of men have been trained in the use of the rotary; in fact, many standard-tool men have abandoned standard drilling and, starting in as roustabouts, have become thoroughly competent rotary operators. The improvements in the machinery have been such as to remove many of the objections and the rotary drilling of to-day is in every way superior to that of 1910. In contrast, a well drilled recently by the Kern Trading & Oil Co., in the east side Coalinga field may be cited. The first 2,500 ft. was drilled in 24 days and it is confidently expected that the water string will be set with a rotary at 3,400 ft.—a record obviously far beyond that made in 1910 by the Nevada Petroleum Co. The records herewith are published with the hope that some one having more recent data will publish them so that comparison may be

Jan 1, 1915

ASIDE from the John Fritz Medal, in which the Institute partici¬pates through its representation on the John Fritz Medal Board, the Institute itself has three major awards to make annually and one special prize for excellence in technical papers, as follows The Robert W. Hunt Medal and Prize, The J. E. Johnson, Jr , Award, the James Douglas Medal, and The Lewisohn Platinum Prize to senior members. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules¬ 1 The award shall consist of two prizes, first of a gold medal, second of a sum of money, a certificate to accompany each prize. The money prize shall not be awarded to -a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side m recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3 A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval.. , 4 The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5 The recipient of the award shall be designated "The Hunt Medallist " This prize is administered by the Iron and Steel Committee.

Jan 1, 1923

By B. D. Cullity

GOLD and beryllium form an intermediate phase composed of the two metals in equal atomic proportions and having the formula AuBe. According to Winkler,1 this phase probably exists in two modifications: beta, stable below about 600°C, and alpha, stable between 600°C and the melting point, about 740°C. Only the low- temperature beta form will be considered in this paper. EXPERIMENTAL PROCEDURE The gold used had a fineness of 999.75 to 999.85, balance mainly silver, and the beryllium purity was better than 99.8 pct. AuBe was prepared by melting the constituents in a beryllia crucible in an evacuated induction furnace. After melting and thorough mixing, the alloy was allowed to solidify in the crucible. No difficulty was encountered in obtaining a homogeneous ingot. Both chemical analysis and microscopic examination of the ingot showed that the alloy was essentially one phase, containing 50 at. pct gold. The alloy was quite brittle and powder samples could easily be pre- pared by grinding in an agate mortar. The X-ray diffraction patterns were made with CuK-alpha radiation in a Debye-Scherrer powder camera 57.3 mm in diameter. The film was placed unsymmetrically in the camera in order to afford a basis for am-shrinkage corrections. A sample homogenized at 5o0°C gave the same diffraction pattern as a sample taken from the as-melted ingot. GENERAL RESULTS The diffraction pattern of AuBe was readily indexed on the basis of a simple cubic lattice with ao = 4.659 ± 0.001kX. If the unit cell is assumed to contain four AuBe "molecules," the calculated X-ray density is 13.46 grams per cc as compared with the measured density of 13.55 gm per cc. The only missing reflections in the dsraction pattern are (100) and (220) (see Table I). Since these missing reflections are not those characteristic of body or face centering, the lattice of AuBe must be simple cubic. To locate the positions of the atoms within the unit cell, two possibilities had to be considered: I. The structure was disordered and there were eight positions to be filled by an "average" gold-beryllium atom. That the structure was disordered seemed unlikely since the lattice parameter did not vary with composition in alloys containing some- what more and somewhat less than 50 at. pct gold, indicating a fixed composition for AuBe.

Jan 1, 1947