Search Documents

By E. H. Rose

The question is often pondered whether the flotation process is still an art or has become a science. The fact is that flotation is a science in so many variables that only art can blend them. It is demonstrable that no less than one hundred variables are involved in any flotation operation, most of them immeasurable on a routine basis. The behavior of every one of them is always governed by orderly and unchanging law, as no man can doubt. There is nothing truly indefinite about that behavior; the only indefiniteness is in our knowledge of it, either in general or from hour to hour in the circuit. In dealing with a simultaneous equation in, say, one hundred variables, all not only affecting the outcome to some degree but many influencing each other as well, it is small wonder that the mineral-dressing profession presents a case history of debate and controversial opinion. The statement of the subject of this symposium—a symposium on flotation machines—seems to delimit and define the matters to be considered and at least the general nature of the conclusions sought. Nevertheless, in such a meeting it is not possible to meditate upon all the variables that do in one way or another affect performance of flotation machines. To attempt it would be much like trying to operate a hundred-ring circus. Perverse variables being what they are, one could expect the elephant in ring 36 to squirt a trunkful of water at the tightrope performer in ring 37 to ruin that artist's act, just as our learning to depress pyrite in the early 1920's ruined the act of the formerly faithful old Callows. Honest Disagreements Selective flotation dates from 1922 or 1923, when several plants established their regular flotation operations on a selective basis. Since then, two decades of efforr have gone into the development of better and better flotation machines. Many have come and gone. The competition has simmered down to perhaps a dozen machines, each one of which is staunchly defended by some operators as being the best for their particular jobs, and as scornfully dismissed by at least a few others elsewhere as being positively the poorest for theirs. These disagreements are honest disagreements, honestly arrived at after plenty of sweat. In many a flotation plant, one machine has been tried out against another under conditions as fair as they could possibly be made. Sometimes the results are on a par but more often one machine shows a consistent and unmistakable margin of superiority over the other. In equally honest and enlightened tests, machine A may win over machine B in one place, and machine B over machine A by as great a margin in another. This paper purposes to identify some of the more prominent reasons why this is so,

Jan 1, 1947

By E. H. Rose

The question is often pondered whether the flotation process is still an art or has become a science. The fact is that flotation is a science in so many variables that only art can blend them. It is demonstrable that no less than one hundred variables are involved in any flotation operation, most of them immeasurable on a routine basis. The behavior of every one of them is always governed by orderly and unchanging law, as no man can doubt. There is nothing truly indefinite about that behavior; the only indefiniteness is in our knowledge of it, either in general or from hour to hour in the circuit. In dealing with a simultaneous equation in, say, one hundred variables, all not only affecting the outcome to some degree but many influencing each other as well, it is small wonder that the mineral-dressing profession presents a case history of debate and controversial opinion. The statement of the subject of this symposium—a symposium on flotation machines—seems to delimit and define the matters to be considered and at least the general nature of the conclusions sought. Nevertheless, in such a meeting it is not possible to meditate upon all the variables that do in one way or another affect performance of flotation machines. To attempt it would be much like trying to operate a hundred-ring circus. Perverse variables being what they are, one could expect the elephant in ring 36 to squirt a trunkful of water at the tightrope performer in ring 37 to ruin that artist's act, just as our learning to depress pyrite in the early 1920's ruined the act of the formerly faithful old Callows. Honest Disagreements Selective flotation dates from 1922 or 1923, when several plants established their regular flotation operations on a selective basis. Since then, two decades of efforr have gone into the development of better and better flotation machines. Many have come and gone. The competition has simmered down to perhaps a dozen machines, each one of which is staunchly defended by some operators as being the best for their particular jobs, and as scornfully dismissed by at least a few others elsewhere as being positively the poorest for theirs. These disagreements are honest disagreements, honestly arrived at after plenty of sweat. In many a flotation plant, one machine has been tried out against another under conditions as fair as they could possibly be made. Sometimes the results are on a par but more often one machine shows a consistent and unmistakable margin of superiority over the other. In equally honest and enlightened tests, machine A may win over machine B in one place, and machine B over machine A by as great a margin in another. This paper purposes to identify some of the more prominent reasons why this is so,

Jan 1, 1947

By E. H. Rose

THE question is often pondered whether the flotation process is still an art or has become a science. The fact is that flotation is a science in so many variables that only art can blend them. It is demonstrable that no less than one hundred variables are involved in any flotation operation, most of them immeasurable on a routine basis. The behavior of every one of them is always governed by orderly and unchanging law, as no man can doubt. There is nothing truly indefinite about that behavior; the only indefiniteness is in our knowledge of it, either in general or from hour to hour in the circuit. In dealing with a simultaneous equation in, say, one hundred variables, all not only affecting the outcome to some degree but many influencing each other as well, it is small wonder that the mineral-dressing profession presents a case history of debate and controversial opinion. The statement of the subject of this symposium-a symposium on flotation machines-seems to delimit and define the matters to be considered and at least the general nature of the conclusions sought. Nevertheless, in such a meeting it is not possible to meditate upon all the variables that do in one way or another affect performance of flotation machines. To attempt it would be much like trying to operate a hundred-ring circus. Perverse variables being what they are, one could expect the elephant in ring 36 to squirt a trunkful of water at the tightrope performer in ring 37 to ruin that artist's act, just as our learning to depress pyrite in the early 1920's ruined the act of the formerly faithful old Callows. HONEST DISAGREEMENTS Selective flotation dates from 1922 or 1923, when several plants established their regular flotation operations on a selective basis. Since then, two decades of efforr have gone into the development of better and better flotation machines. Many have come and gone. The competition has simmered down to perhaps a dozen machines, each one of which is staunchly defended by some operators as being the best for their particular jobs, and as scornfully dismissed by at least a few others elsewhere as being positively the poorest for theirs. These disagreements are honest disagreements, honestly arrived at after plenty of sweat. In many a flotation plant, one machine has been tried out against another under conditions as fair as they could possibly be made. Sometimes the results are on a par but more often one machine shows a consistent and unmistakable margin of superiority over the other. In equally honest and enlightened tests, machine A may win over machine B in one place, and machine B over machine A by as great a margin in another. This paper purposes to identify some of the more prominent reasons why this is so,

Jan 1, 1944

By M. R. Hatfield, F. J. Vosburgh

IN a recent article,† it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell-to keep it cool enough for safety and comfort and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a carbon tube nominally 2 5/8 in. o.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a 15-kva. transformer operating

Jan 1, 1941

By C. V. Millikan, Herbert F. Beardmore

Declining Productivity Index, as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. If not recognized, it may be interpreted as representing an unsettled or unstable condition in a producing well. It forms the basis of a number of predictions as to future performance compared with the performance of wells in which the productivity index does not decline. The nost important of these are that: (I) the rate of oil production will decline more rapidly, (2) the gas-oil ratio will usually increase abnormally, (3) the amount of water ultimately produced will be negligible, if any, (4) stop-cocking will increase current production and decrease gas-oil ratio. When such relative well performance is indicated, it follows that certain reservoir performance and operating practices may be anticipated: (I) disappointing recovery, (2) longer natural flow, (3) no active water drive, (4) better evaluation of acidizing, shooting and reworking, (5) intermittent operation of wells, (6) smaller pumping equipment required. It is significant that the basis of these important predictions is bottom-hole pressure tests that can be made immediately after completion of the wells. Introduction "'Productivity index" is the number of barrels of oil produced per day per pound per square inch of differential pressure between the reservoir and the bottom of the well. "Declining Productivity Index," as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. Productivity index can be determined only when the rate of production can be stabilized. In most wells the rate of production and bottom-hole pressure are easily stabilized to give a constant productivity index for a period of many hours. A few produce so erratically as to preclude probability of an acceptable test in the usual sense. A satisfactory productivity index can be determined in some wells only by gauging the production accurately by hours, measuring the bottom-hole pressure continuously, and from these data calculating the productivity index for successive hours. Such figures frequently will have a decreasing value—that is, a declining productivity index—and when plotted on double. logarithmic cross-section paper with productivity index as ordinate and time as abscissa will be a straight-line curve. The angle between the curve and the abscissa is referred to as the rate of decline. Declining productivity index may appear to be the result of change in permeability to oil due to decreasing saturation of oil and increasing saturation of gas in the reservoir. It is possible that such is in fact the cause, but if so, more is involved than merely relative saturation of oil and gas. This seems evident because the rate of decline in productivity index is substantially the same regardless of the pro-

Jan 1, 1945

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always-have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1951

By Henry D. Hibbard

The finishing and casting temperature of steel is a subject concerning which there is so much to learn that some temerity is required to write about it. This paper is, therefore, suggestive rather than dogmatic, though the views expressed seem now to the writer to be correct; nevertheless, they may be modified by future developments or discoveries but until then may be of some utility, particularly to beginners in the making of steel. Consideration is limited to the temperatures of simple steels, also called carbon steels, which are those in which carbon is the only element introduced for the purpose of conferring desired physical properties. Alloy steels will receive attention later. Three things largely determine what a batch of steel really will be; via., composition, casting temperature, and rate of teeming. Each has its advocates as being the most important; but they are so interrelated that each must conform to or be right for the other two. When one is claimed to be the most essential to have right, that, probably, was the one that it was found had to be of a certain description, within narrow limits, to suit the already adopted variations of the other two; that is, it was the last of the three to be brought into line. The term "casting temperature" is rather indefinite as there ale several temperatures to which the term may be applied. Most writers who have mentioned casting temperature of steel have alluded to it in relative terms. The few who have given actual temperatures, including Langmuir, Burgess, Styri, and Bash, do not give full information about them. Their results demonstrate the efficiency of pyrometers used rather than aid the steelmaker. In order to understand and use the temperatures, one should know in each case what the steel was, the stage at which the temperature was taken, whether it was usual or not, and whether or not it was right for that steel at that stage. When these

Jan 1, 1925

By J. J. Kanter

There has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-temperature steels" are meant those specifically designed for service at elevated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service. Uses of Silicon Next to oxygen, silicon is the most widely distributed and abundant of the earth's substances. Although classed as a nonmetal, it is highly important in the metallurgy of all steels, having been used for years as an efficient and economical degasifier and deoxidizer. Silicon is added to various steels in the form of ferrosilicon, generally at the end of the heat so as to avoid oxidation losses. With acid steels it is added in the furnace (also in the ladle) and generally with basic steels is added in the ladle, so as to avoid reaction with the basic lining through high-temperature acidic reaction with silica, which may be formed by oxidation of the silicon alloy. Several grades of ferrosilicon are available, containing, respectively, 15, 50, 75 and 90 per cent Si. By far the largest tonnage produced is the 50 per cent grade although the 75 and 90 per cent ferro-silicons are used as ladle and furnace additions in the manufacture of steels of high silicon content. The introduction of silicon into steel as an alloying element is well known in connection with high-yield-strength constructional steel for bridges, ships, car construction, etc., and it is also well known as an alloy-

Jan 1, 1938

By J. J. Kanter

There has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-temperature steels" are meant those specifically designed for service at elevated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service. Uses of Silicon Next to oxygen, silicon is the most widely distributed and abundant of the earth's substances. Although classed as a nonmetal, it is highly important in the metallurgy of all steels, having been used for years as an efficient and economical degasifier and deoxidizer. Silicon is added to various steels in the form of ferrosilicon, generally at the end of the heat so as to avoid oxidation losses. With acid steels it is added in the furnace (also in the ladle) and generally with basic steels is added in the ladle, so as to avoid reaction with the basic lining through high-temperature acidic reaction with silica, which may be formed by oxidation of the silicon alloy. Several grades of ferrosilicon are available, containing, respectively, 15, 50, 75 and 90 per cent Si. By far the largest tonnage produced is the 50 per cent grade although the 75 and 90 per cent ferro-silicons are used as ladle and furnace additions in the manufacture of steels of high silicon content. The introduction of silicon into steel as an alloying element is well known in connection with high-yield-strength constructional steel for bridges, ships, car construction, etc., and it is also well known as an alloy-

Jan 1, 1938

By Benjamin Talbot

The problem of segregation and cavities in steel ingots is a subject which has given and is still giving metallurgists, engineers, and operators matter for serious consideration. This question has come more into prominence lately in the United States, due largely to the desire of railroad engineers to secure a better rail than they have obtained ill the past, as the service they demand is increasing in severity; and no doubt manufacturers will be able to meet what is required of them. The rails here are as good as those made in other countries, but the conditions of service and the extremes of climate are more Revere and consequently more breakages occur. Various reasons have been advanced to explain why rails may not be as good in quality to-day as in the past. Some engineers consider that modern methods of manufacturing, designed chiefly to obtain large output, tend to reduce the standard of excellence of more deliberate methods. Others think that 4-ton ingots are worse than those of 2 tons. Again, it is stated that the 100-ton heat in one ladle is too large, and is a step in the wrong direction in casting. My experience upon the question of the size of the ingot is that in rolling rails of from 85-to 100-lb. sections, the range of ingot is only practically such that the difference in the size does not help in the question of segregation, cavities, or blow-holes. I call attention to two ingots from work done at Pencoyd, Pa., 16 years ago. These ingots were bottom-poured, cast at the same time from the same center-runner, the one being 20 by 24 in. and the other 13 by 16 in. in size. The steel was acid open-hearth, and contained C, 0.43; P, 0.062; S, 0.069 per cent. At the same place in each ingot where seg-

Jan 1, 1914

By A. B. Kinzel

THE demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low tempera-tures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selec-tion of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low tempera-tures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120° C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937

By C. B. Post, D. G. Schoffstall

A determinatioil of the hydrogen content of molten steel by means of the Vacuum-extraction method, as reported here, consists in first casting a sample of the bath in a bomb, so that the gases evolved during solidification are trapped for analysis. A portion of the cast steel sample is then prepared and heated at a temperature of 600" to 800°C. under high vacuum, and the gaser given off during this vacuum extraction (which are shown to be hydrogen), are collected and measured. Analysis of the gases evolved on solidification and the gases in the solid sample enables an accurate determination of hydrogen in the molten steel. Fig. I shows the bomb and accessories that have been found suitable for trapping the gases evolved on solidification. The bomb is made of scamless steel pipe, approximately 7 in. long by 136 in. i.d., and welded at the bottom. An ordinary pipe cap has a vacuuni-type metal stopcock threaded and brazed in its upper end. This pipe cap fits onto the bomb by means of machined threads. A flange is brazed to the pipe at the point where the cap starts to tighten up, and a rubber gasket is placed between the flange and cap. Heavy vacuum grease is used between the flange and gasket and the gasket and cap. The weight of the complete bomb and it? interval volume is known before the sample is cast. In practice, a sample of about 400 grams of steel is poured into the bomb, the funnel quickly swung out of the way, the bomb cap spun down the threads and tightened against the gasket, and the bomb set in a pail of water to keep the gasket and vacuum grease cool. It is estimated that at least 80 per cent 01 the gases evolved from the liquid sample during solidification are trapped in the bomb."

Jan 1, 1945

By Norman D. Fitz Gerald

The lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnecessary drilling.' While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a technique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer's good, while residual fuel oil is almost entirely a producer's good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

By Norman D. Fitz Gerald

The lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnecessary drilling.' While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a technique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer's good, while residual fuel oil is almost entirely a producer's good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

By Ian W. Wark, Keith L. Sutherland

IT has been shown' that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "standard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,2 it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator. It is not difficult to suggest an explanation for the influence of the carbonate ion in the presence of copper sulphate. The works of Picker-

Jan 1, 1939

By J. Bulina, J. T. Brown

SINCE the inception of vacuum cold-hearth arc melting of high-temperature alloys (about 4 years ago) it has been theoretically reasoned and qualitatively found that better mechanical properties are often obtained from alloys which have been melted by this practice. Mechanical properties are emphasized in this evaluation because of their importance in design. Vacuum-arc melting has an intrinsic advantage in that it creates an ingot grain structure which is easier to forge and thus leads to greater yields for the finished product. The greater yield naturally gives the process an economic basis when the cost per pound of alloy is rather high. However, the question stressed here is, does the process create an alloy with inherently better properties? There are several theoretical reasons for suspecting that it does. One is the vacuum refining which should permit lowering the content of harmful residuals with high vapor pressures. A second is the vacuum process which should preclude the formation of harmful distribution of oxides, nitrides, or carbo-nitrides, by keeping the amount of such constituents formed to a minimum. A third is the vacuum-arc cold-hearth method which prevents the possibility of pick-up of harmful elements from a refractory crucible since none is used. Fourth, the rapid solidification rate, induced by having a cold mold and only small amounts of molten metal at any one time, minimizes the segregation of elements like titanium, aluminum, and molybdenum from the top to the bottom of the ingot. This rapid solidification rate also decreases the tendency of the above elements to form undesirable phases by segregating locally. Another less frequently considered vacuum-arc melting advantage is the inherently finer-grained ingot structure which can be produced. Finer initial grain size leads to better forgeability, and means that after relatively small reductions to billets or final forged products a finer-grained material is obtained, which, by virtue of its finer grain size, would usually have greater stress-rupture ductility.

Jan 1, 1960

By Rex B. McLellan

Studies of the eyuilibrzum between ferrite and austenite with gas mixtures (CO + CO2 and H2 + CHe) have been used as a means of deducing the energy and vibrational entropy of carbon atoms in dilute interstitial Fe-C solutions. A simple model for dilute interstitial solutions is given which enables a solubility equation for the equilibrium between the gas mixtures and the solid to be deduced. This solubility equation is used to estimate the partial In this work measurements of the equilibrium between dilute solid solutions of carbon in iron and gaseous mixtures of CO2 + CO and CH4 + Hp have been analyzed using theoretical solubility equations deduced from a knowledge of the thermodynamic parameters of the gas mixtures and an appropriate model for the solid solution. The solubility equations are deduced by equating the chemical potential of carbon atoms in the gas thermodynamic functions of dilute Fe-C solutions from the measured equilibrium between the solid and the gas mixtures. It is shown that the vibra-tional entropy of a carbon atom in a and y iron is smaller than the corresponding entropy 01. a nitrogen atom in solid solution inferrite or austenite and that there is little difference between the vibrational entropies of both nitrogen and carbon atoms in ferrite and austenite. and solid phases. The chemical potential of carbon in the gas is found from a simple statistical mechanical analysis of the gas mixtures utilizing spec-troscopic data while that for carbon in the interstitial solution is found from a model in which the carbon atoms act as bound oscillators distributed in a random fashion in the solution. The solid solution is dilute enough to enable solute-solute interactions to be ignored. Thus the configurational entropy of the solution is ideal but the mixing entropy contains additional excess terms due mainly to the vibrational changes occurring on solution formation. The partial excess entropies (and the partial energies) do

Jan 1, 1965

By A. K. Knickerbocker

PRACTICALLY all underground work on the Minnesota iron ranges is done by miners working on a so-called contract wage system. This system, while it has certain advantages over the straight day's pay or company-account method of wage payment, has serious and vital defects. In view of the scarcity and demands of labor, it is important that employers of labor scrutinize their systems of wage payments carefully, not only to save losses and trouble, due to labor disturbances, but also to secure the greatest efficiency of their workmen and reduce their operating costs. It is admitted that an adequate, just, and equitable wage is the prime factor in bringing about these benefits. The wage of labor and its method of application and payment have been, and always will be, the main factors in the unrest and dissatisfaction of labor. Not only does labor want and need an adequate wage, assuming that work is adequately performed, but it wants and is entitled to a just and equitable wage. Labor must have respect for the fairness of the wage and for the fairness of the management in the application of the wage. It is conceded that the Minnesota iron miners are now, and have been, in the main paid adequately, but the inherent defects of the so-called contract system prevent any just or equitable application of this wage to the various units of the labor body. The defects of the contract system, with its obvious inequalities, favoritisms, and injustices, are cancers in the brain of labor. Every thinking miner realizes these defects and knows just what they are; the unthinking do not realize the details of the subject, but each month they are forcibly reminded of these defects through the pay envelope. As practiced on the iron ranges, however, the so-called." contract" system is not a contract and the name is a misnomer. No true contractual obligation exists.

Jan 2, 1920

By Paul M. Tyler, Oliver Bowles

The extensive employment of nonmetallic minerals antedates the use of metals, but only within the last two decades has the production of nonmetals begun actually to keep pace with the complicated activities which characterize the so-called Machine Age. The economic changes ushered in by the Industrial Revolution were reflected first in an increased demand for metals and for fuels. In the modern sense, therefore, the nonmetallic mineral industries are new and afford new opportunities for engineer and economist alike. A certain amount of caution is indicated, therefore, before attempting to apply ready-made formulas to the problems of these industries. Economics is not an exact science. In the field of production technology where the number of variables is fairly well known, the principles of economics are readily applicable, but as the student proceeds through the province of marketing into the unexplored regions of psychology and sociology he must distinguish carefully between scientific reasoning and purely metaphysical speculation, even when the latter masquerades as economics. The present paper attempts to prove no preconceived theorems and is designed primarily to stimulate careful thinking on sundry neglected phases of these industries. An attempt is made to differentiate the general problems into single aspects which afford promise of being comprehended separately; also, some fundamental statistical data are presented, but merely to indicate a method of scientific approach applicable to more intensive studies. Definition Before discussing the economics of the nonmetallic mineral industries, it is appropriate to consider what we mean when we say "nonmetallic minerals." This term, inasmuch as it is merely a negative description, is somewhat loose and ambiguous and gives rise to questions in regard to minerals that, like chromite or bauxite, are alternatively classed either as nonmetallic or as metallic minerals (or ores). The chrome ore used to make ferrochrome for steel manufacture is undoubtedly metallic in character; similar material destined for use as a refractory in the same

Jan 1, 1934

By F. F. Aplan

For the past year, MBD has been engaged in a lively discussion on a name change for the Division. To complicate things, more than one name change has been proposed! There has been much discussion on the subject, as anyone who has attended the Annual MBD Business Meeting or read [jE] knows. The position of many of our members is well known. There is, however, one group that has not been heard from. These are the future members-the present students and those even younger who are yet to elect our profession. As one who has traversed the academic-industrial interface several times, I think I am qualified to speak for this group. Before going further I think it wise to state unequivocally that our Division should adequately represent our profession. The whole profession is just too small to chop into a plethora of pieces: "I'm not a mineral processing engineer, I'm an ore dresser-well, actually, I specialize in comminution, specifically in grinding, mostly in autogeneous grinding-primary autogeneous grinding that is-and my 'thing' is really iron ores, taconites, mind you!" Enough to confuse even those that keep the faith, and certainly we can't build a profession on such narrow pieces. Either an employer can hire a professional who knows the entire profession or he can't. As more and more companies search out opportunities in the mining and metallurgical fields and as environmental considerations bring into question even our technically well proven processes and procedures, there is a greater need than ever be- fore for a well-rounded mineral processing engineer well versed in all of the process possibilities. What is needed is one who can take an ore-or municipal trash for that matter-and produce there from a valuable product by the most appropriate means. It doesn't really matter if this is done physically, chemically or thermally.

Jan 1, 1971