Search Documents

By E. R. Gilbert

Klopp et al. have reported data on tensile and creep properties of are-melted and electron-beam-melted tungsten. We would like to point out some similarities between their creep results and ours on are-melted and powder-metallurgy tungstenand offer some alternate interpretations of the data which lead to different rate-controlling mechanisms. Klopp et al. observed extensive transient creep in the 2250" to 3500°F temperature range where the acthetivation energy is 106,400 ± 3300 cal mole-1. They suggest cross slip as the possible rate-controlling mechanism since "cross slip may occur only by the movement of screw dislocations, and not edge dislocations, thus allowing only partial recovery of the strain hardening and resulting in a continuously decreasing creep rate, characteristic of transient creep.'' Our tests on are-melted tungsten and powder-metallurgy tungsten displayed an extensive transient creep stage in the same temperature range but they also displayed a steady-state creep stage. The stress levels and strain rates of the two investigations, 1.4 to 7 kg mm-2 and 10-7 to 10-4 sec-1 for that of Klopp et al. and 4.5 to 10 kg mm-2 and 10-8 to 10-4 sec-1 for those of Gilbert et al., are overlapping. The activation energy for creep of our powder-metallurgy tungsten is 105,000 cal mole-1. This close agreement with the value found by Klopp et al. suggests that the same mechanism may be common to both types of materials. It may be possible to gain some additional insight into the rate-controlling mechanism by applying the analysis made by conrad22 in terms of the activation volume. The value for the activation volume depends upon the dislocation mechanism and may be used to help differentiate between various dislocation mechanisms. The activation volume for cross slip is 10 to 100 b3. Values determined from our data were 130 to 220 b3 which are in better agreement with the range of 102 to 104 b3 for nonconservative motion of jogs. Values determined from data of Klopp et al. are 240 to 1040 b3. We suggest that the rate-controlling mechanism for creep in this temperature range may be nonconservative motion of jogs assisted by enhanced diffusion along grain boundaries or dislocations. This model requires an activation energy lower than that for self-diffusion as is observed. If this is the controlling mechanism, a higher activation energy which is closer to that for self-diffusion might be expected for tests conducted on specimens with reduced grain boundary area, i.e., larger grain size. In support of this premise we have conducted tests on speci- mens having one to three grains per cross section for which a higher activation energy of 130,000 cal mole-1 was observed. Also, in agreement with results of Klopp et al., a faster creep rate resulted from the increased grain size and probable decreased dislocation density. Further argument against the cross slip mechanism is based on the constant activation energy we obsserved over the range of 5.0 to 10 kg mm-2,21 whereas the activation energy for cross slip displays a significant stress dependence.23 In addition to this, the powe on the stress term for the strain-rate dependence appears too high for cross slip. The values for tungsten fall in the range of 4.5 to 7 (Klopp et al. and Ref. 21) whereas values of approximately 2 are observed in creep by cross slip for hep metals.24 At temperatures from 3300° to 4000°F, Klopp et al. observed an activation energy of 141,000 ± 4000 cal mole-' which is less than that for self-diffusion, 153,000 cal mole-1, 25 and less than that reported for high-temperature creep of powder-metallurgy tungsten by Green:' 160,000 cal mole-1. Klopp et al. suggested that recovery of strain hardening by dislocation climb is the rate-controlling mechanism in this temperature region. Actually an activation energy larger than that for self-diffusion is predicted by this model if the temperature dependence of the elastic modulus27 is taken into consideration. Klopp et al. attributed this lack of correlation to the compositional differences between powder-metallurgy tungsten used by Green and their own arc- and EB-melted tungsten. It is our position that the value of 141,000 ± 4000 cal mole-' represents a transitional value between the higher and lower activation energies and does not represent a discrete mechanism of deformation. If the tests had been extended to higher temperatures the higher value of activation energy would have been observed as has been demonstrated by both our analy sis'' of isothermal test data by GE-NMPO28 and differential temperature tests28 on are-melted tungsten. The activation energies determined (170,000 and 160,000 cal mole-1) were greater than that for self-diffusion and are in better agreement with the value found by Green. The model of dislocation climb is associated with ; activation volume of 1 b3 according to Conrad.22 The activation volume calculated for the creep data of fou independent investigators in the temperature range where the activation energy for creep is near that for self-diffusion (Klopp et al. and Refs. 26, 28, and 30) is 110 to 2800 b3 and is in the range suggested for nonconservative motion of jogs. In the case of tungsten this mechanism may be preferred over that of dislocation climb. Sincere appreciation is expressed to Messrs. J. E. Flinn and F. L. Yaggee for the helpful discussions and suggestions in the preparation of this communication.

Jan 1, 1967

By A. K. Mukherjee, J. E. Dorn, J. D. Mole

Investigations were carried out on the effect of polyslip on the strain hardening of aluminum single crystals. The orientations investigated were those lor which the tensile axis was in the [001], [111], [112], and [012] directions plus another for which the Schmid angles for {111}(110) slip were 1 deg. The experimental data were analyzed on a model based on the intersection of dislocations with particular emphasis on the effect of polyslip on the activation volume for inter-section. It is shown that the rate of strain hardening inreases for those orientations wherein attractive dislocation intersections occur and that those orientations which produce the greater number of such intersections exhibit the greater strain hardening. Good correlation of the data is obtained with the concept that attractive junctions, as proposed by Saada, Play an important role in accounting for the rate of strain hardening. EXISTING concepts on the nature and cause of strain hardening in fcc metals have been deduced principally from experiments on the deformation of single crystals under single slip. The effect of crystal orientation on the shapes of the stress-strain curves for single slip have been summarized by seegerl and more recently by Clarebrough and Hargreaves.2 Tensile specimens whose axes fall near the center of the [001]-[011] line of the standard triangle of the stereographic projection exhibit the longest range of easy glide (Stage I) and the lowest rates of linear hardening (Stage 11) whereas specimens whose axes lie near fie [001]-[111] line of the standard triangle have limited or no easy-glide range and exhibit somewhat higher linear strain-hardening rates. Specimens whose axes lie near the [001] or the [ill] poles do not exhibit easy glide and have the highest rates of linear hardening. Kocks3 has shown that the highest rates of linear hardening Occur under Polyslip when the tensile axis coincides with the [111] or the [ 001] pole. Since the rate of strain hardening is sensitive to specimen orientation and the incidence of polyslip, these relationships might help to discriminate between various dislocation models for strain hardening in fcc metals. Previous attempts to analyze the effect of orientation on strain hardening,1"3 however, did not provide a unique answer to this problem. Consequently the present investigation was undertaken wherein additional data, particularly that for the effect of polyslip on the activation volume for intersection, was also determined in order to provide more complete information on the details of strain hardening. Whereas analyses of these data reveal that several recommended models for strain hardening are at variance with the facts, good correlation of the data is obtained with the concept that attractive junctions4 play an important role in accounting for the rate of strain hardening. I) EXPERIMENTAL APPROACH seegerl demonstrated that slip in fcc crystals at low temperatures is dependent on thermally activated intersection of glide dislocations with forest dislocations. This has been confirmed by tests on single crystals of aluminum by Mitra, Osborne and Dorn5 and on polycrystalline aluminum by Mitra and Darn.' Thus in accord with Seeger's theory, the shear strain rate, ?, below a critical temperature, T, is where .V is the number of points of contact per unit volume between forest dislocations and glide dislocations, A is the area swept out per successful intersection, b is the Burgers vector, v is the frequency of vibration of the segment of the glide dislocation undertaking intersection, U is the activation energy for intersection, k is Boltzmann's constant, and T is the absolute temperature. For aluminum, which has an extremely high staeking-fault energy, the constriction energy is negligibly small and therefore the activation energy decreases practically linearly with the stress according to as will be recomfirmed later, where Uo is jog energy at the absolute zero, G and Go are the shear moduli at the test temperature T and O°K, respectively, L is the spacing of the forest dislocations, t is the applied shear stress for slip, and tGo is the stress field that must be surmounted athermally.

Jan 1, 1965

By Arthur L. Walker

DURING my trip around the world last year, covering a total of 45,000 miles, I saw many things of especial interest from an engineering viewpoint. Sailing from New York, I went through the Panama Canal, down along the west coast of South America, then over the Peruvian and Bolivian Uplands; thence to the celebrated copper mines of Chile; across the Andes, to Buenos Aires, then to Rio Janeiro; across the Atlantic to Lisbon, Portugal; through Spain to the Rio Tinto mines; across southern Europe to Italy; thence to Alexandria and Cairo; up the Nile to Assouan, to Palestine through the Suez Canal, Red Sea and across to Bombay; up to the country of the Moghul Emperors; then to Calcutta, from which point I shipped to Singapore, as having crossed the Equator twice, I wished to shake hands with it again; thence to Shanghai and Pekin; up to the Great Wall of China, back to Nanking and up the Yangtse to Hankow; then back and eastward across the Pacific Ocean. The climatic changes were sudden and severe; there was winter where, for me, it should have been summer and vice versa. The weather man was very kind, however, and until I was near the Aleutian Islands there were only three rainy days in a total of 220.

Jan 1, 1924

By R. J. Lloyd

INTRODUCTION The Mount Isa Mine is a large modern underground mine located in North-Western Queensland, Australia. Two ore types are mined and treated separately. Currently silver-lead-zinc ore is mined at the rate of 2.6 million tonnes per annum and copper ore at the rate of 4.6 million tonnes per annum. The silver-lead-zinc orebodies are mined by sub level open stoping and cut and fill methods whilst all copper ore is extracted by various forms of sub level open stoping. The mining operations are highly mechanised and utilise diesel powered load-haul-dump units of various sizes, two and three boom face drilling jumbos, electric-hydraulic rotary-percussive ring drills, in-the-hole hammer drills, rotary blasthole drills, raiseborers, battery/trolley locomotives, a large fleet of rubber tyred service and supply vehicles plus light rockdrills mounted on airlegs, rail mounted overshot shovels and battery and diesel powered locomotives. All stoping production ore is extracted with diesel powered load-haul-dump units. The ore is tipped into orepasses which connect to the main rail haulage levels. On the haulage levels electric battery/trolley locomotives are used to pull rakes of bottom dump or side dump trucks which feed the ore into primary crushers. Following two stage crushing the ore is conveyed to the shaft and hoistod to surface in bottom dump skips. Each ore stream has its own rail transport system, crushing stations and hoisting shaft feeding separate concentrators. This paper will consider some aspects of the role of equipment and machinery in the growth of the mine, will discuss in some detail the machinery and equipment in use today and will conclude with a look at some possible developments in mining equipment for the future, with particular reference to the Mount Isa Mine. A summary of mining equipment in use at Mount Isa is given in the Appendix. THE PAST Silver-lead-zinc ore was discovered at Mount Isa in 1923 and within a very short time many small mines were being developed. However the rich surface ore traces did not continue and by 1928 Mount Isa Mines Limited had acquired sufficient leases to plan for a large scale mine to exploit the low grade orebodies. At this early stage it was recognised that the mine would need to adopt the most mechanised mining techniques then available in order to overcome its twin disadvantages of low graaes and extreme remoteness. The Company introduced bar mounted drifters and overshot shovels to replace hammer and tap and hand shovelling in development work and by 1930 headings were advancing at the rate of 30 metres per week. In keeping with the concept of mechanisation the early engineers designed the Man and Supply shaft with a very large, for those days, cage compartment measuring 3.8 m x 3.4 m. This shaft was the main means of access into the mine for 36 years until the K57 shaft (now R62 shaft) was commissioned in 1966. Man and Supply is still in regular use. Production commenced in 1931 at an annual rate of approximately 660 000 tonnes of silver-lead-zinc ore. The mine was mechanised to an extent which was previously unknown in Australia; whilst the concentrator, smelter and power house utilised the most modern and efficient equipment available. Even so, the mine was very near to closure on several occasions and did not return a dividend to its shareholders for many years. Production levels remained at or slightly below 660 000 tonnes until a separate copper ore streani and mill was commissioned in 1953, doubling the existing production levels. The first underground crushers were installed at this time. Production rates expanded in the years between 1953 and 1973. By 1960 production reached 2740 000 tonnes of ore. In 1965-66 total production was 3650 000 tonnes and in 1973 the production rate plateaued at the current level.

Jan 1, 1981

By C. C. Nitchie, G. S. Brooks

With the gradual depletion of the natural-gas pools of the Kansas district, together with the uncertainty of further cheap fuel developments, some of the western zinc companies turned to the coal fields, attracted by their permanency and the success of the Matthiessen & Hegeler Co. and the lllinois Zinc Co. Being then confronted with the problem of using a relatively high-priced fuel, although the ultimate supply was very great, the fuel economies of the kilns and furnaces became of far more importance, and the more modern equipments, as a result, embodied distinct gaias in this phase of the business. In addition, there have been some pronounced advances in the actual making of gas from these coals. Increased efficiency in gas making has contributed its hare to lowering costs and those plants located in the higher priced fuel districts have probably been obliged to study these economies somewhat more closely. Naturally, many beneficial changes have resulted in both practice and apparatus in these sections. On certain western coals, for instance, the actual saving in fuel consumption has been 50 per cent. By this is meant that, where about 1.75 tons were burned to smelt 1 ton of oxidized ore, 0.7 to 0.9 ton is now required. While comparisons by T. R. Ingalls1 of fuel economies in smelting in this country and Germany before the war may, in general, be correct, they do not appear to do justice to the more progressive American practice. It is doubtful whether German plants were substantially bettering these fuel ratios. Data furnished by Bender and Frams do not afford records averaging less than 0.9 ton coal per ton ore on materials from 40 per cent. to 50 per cent. zinc. Fuels As producer fuel, Illinois, Indiana, and Kansas coah offer a wide range of material, although varying much in their amenability to gasscation. The proper fuel for each plant can only be determined after com-

Jan 1, 1920

By W. O. Philbrook, K. M. Goldman, G. Derge

T. Rosenqvist—The most interesting point in this paper is the observed transfer of iron into the slag in the initial stage of the desulphurization process, after which the iron again is reduced to the metallic state. The authors interpret this observation as showing that the sulphur enters the slag as an iron-sulphur compound which subsequently is decomposed by the slag. The present writer has previously suggested the following equation for the desulphurization process: S + O2- ? S2- + O For equilibrium in the blast furnace the oxygen potential is defined by equilibrium with graphite and CO of 1 atm pressure: C + O ? CO [2] During the desulphurization process the reactions proceed in the direction of the arrows. If one assumes eq 2 to be significantly slower than eq 1, the transfer of sulphur into the slag, in accordance with eq 1, will build up a local oxygen potential at the metal-slag interface very much higher than that corresponding to the value defined by eq 2. This is possible because the equilibrium oxygen potential in eq 1 is high as long as the sulphur content in the slag is low. This oxygen potential will again be able to oxidize some iron: Fe + O ? Fe2+ + O2- and an increase in the iron content of the slag will be observed. Adding up eqs 1 and 3 one obtains: S + Fe ? S2- + Fe2+ The net effect is thus in harmony with the experimental observation but is obtained without assuming any close ties between the sulphur and iron atoms during the process. Furthermore, it follows from eqs 1 and 2 that when the sulphur content in the slag increases, and equilibrium with C and CO is finally approached, the local oxygen potential at the metal-slag interface will decrease, and the iron in the slag will be reduced back into its metallic state. C. E. Sims-—The data and conclusions presented in this paper are thoroughly convincing in establishing the mechanism of sulphur transfer from iron to slag as in a blast furnace. The evolution of gaseous CO in step 3 of the reactions given on p. 1112 makes the process virtually irreversible. Assuming that the process is similar in slag-metal systems other than in the blast furnace, it is readily seen why free CaO and re-ducing conditions so greatly favor desulphurization. On the other hand, the very effective desulphurization obtained in oxidizing slags when strongly basic, must be attributed to the relatively high stability of CaS as compared to FeS. The ease and simplicity with which the reactions of classic chemistry agree with the experimental data and explain the mechanism is noteworthy. The concept of molecules of FeS, soluble in both phases (metallic iron is not soluble in the slag), migrating from the iron to the slag and there reacting with CaO, which is soluble only in the slag phase, is clear and uncomplicated. This is likewise true for step 3. Those who would deny the existence of molecules or molecular-type combinations in liquid iron, must strain to provide a mechanism so lucid. In the absence of molecules, the Fe and S exhibit a remarkable collusion. L. S. Darken—The investigation and interpretation of rate phenomena in the range of steelmaking temperatures is a difficult task. Most of the laboratory investigations of steelmaking reactions have been concerned with equilibrium. Having determined the equilibrium, our attention naturally focuses next on the mechanism and rate of approach to equilibrium. The authors seem to have contributed substantially to our understanding of these factors for the case of sulphur transfer. I should like to ask the authors whether they consider that the sulphur transfer reaction is diffusion controlled as many high-temperature reactions seem to be. If so, it would seem reasonable to suppose that the slow diffusion step of the process is the transfer across a pseudo-static layer or film similar to that considered in heat flow problems. As the diffusivity and fluidity are smaller for the slag than for the metal, it may tentatively be assumed that the sulphur gradient exists in a thin layer in the slag adjacent to the slag-metal interface and that the metal and the main mass of slag are each maintained uniform by convection. On this basis the amount of sulphur transferred across unit area per unit time is D p (?S%)/100 ?1, where D is the diffusivity, p the density, (?S%) the difference in percent sulphur on the two sides of the layer, and ?l is the layer thickness. At the beginning of the experiment the main body of the slag and hence one side of the layer contains no sulphur; therefore (?S%) may be replaced by (S%), the sulphur content of the slag at the slag-metal interface, which in turn is equal to L[S%] where [S%] is the sulphur content of the metal and L is the distribution coefficient. The rate of transfer thus becomes DpL[S%]/100 ?l, which the authors designate K[S%]. Equating these two quantities and setting D = 10-6 cm2 per sec, p = 3 g per cm3, L = 40, and K = lo-+ g cm-2 sec-1, it is found that ?l, the film thickness, is about 0.01 cm—a value of the order of magnitude of that found in heat transfer problems in liquids. The uncertainty of the numerical values used leaves much to be desired, but at least it can be said that this calculation tends to support the proposed model involving diffusion through a film. Although this does not seem to affect the general argument, I should like to call attention to the fact that the diffusivity3 of sulphur in hot metal is found (on conversion of units) to be about 10-4 cm2 per sec rather than 104 cm2 per sec as stated by the authors. The three equations written by the authors to express the steps in the overall process of sulphur transfer may alternatively be written ionically as only two Fe + S = Fe++ + S-- Fe++ + O-- + C (graphite or metal) = CO (gas) + Fe where the underscore is used to designate the metallic phase; ionic species are slag constituents. After the authors have so neatly demonstrated that iron and sulphur transfer together (at least initially), this fact seems almost self evident; from eq 4 it is seen that if sulphur acquires a negative charge during transfer

Jan 1, 1951

By Cyril Wells

THE diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migra-tion of carbon in gamma iron occurs.1,2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with com-position, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schönert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By M. C. Fuerstenau, R. B. Bhappu

The response of beryl to sulfonate flotation was examined. The dependence of flotation recovery on sulfonate concentration, pH, and the absence or presence of various ions is also demonstrated. The response of quartz and feldspar to sulfonate flotation at various values of pH is given to. show the conditions necessary for selective separation. Finally, beryl was successfully concentrated from a natural ore using a technique devised from experimental observations on systems of pure minerals. With the possible exception of quartz, the flotation characteristics of silicate minerals are rather poorly understood. This is due in part to the com- plexity of the mineral systems themselves and in part to an insufficient amount of flotation data. The complexity of the systems arises from the wide range of chemical composition that the silicate minerals can assume. This is reflected in the variability of such physical properties as hardness and cleavage. Although the chemical composition of silicate minerals can vary considerably, a general grouping can be accomplished conveniently on the basis of the assemblage of SiO4 tetrahedra in all the silicates. That is, it has been shown that six basic groups can be obtained, depending on the arrangement of oxygen sharing between adjacent silicon atoms (or substituted aluminum). When all four oxygen atoms are shared, a framework structure such as quartz or feldspar is obtained. When three oxygens are shared, infinite sheets are obtained as in the micas and clays. When two oxygen atoms of the tetrahedra are shared, infinite chains are obtained, such as those in

Jan 1, 1963

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.1 It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anorthosite, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagioclase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a. zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized! The bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15º. The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1952

By H. A. J. Wilkens, H. B. C. Nitze

From time to time papers treating of specific cases of Southern gold-mines and mining have appeared in the Transactions of this Institute, as well as in other journals and publications. Mr. George I?. Becker, of the United States Geological Survey, made a reconnaissance of the Southern Appalachian gold-belt during the fall of 1894; the results of his investigations are published under the title of "A Reconnoissance of the GoldFields of the Southern Appalachians," in the Sixteenth Annual Report of the Director of the United States Geological Survey, 1894-95 : Part III., " Mineral Resources of the United States." Mr. Becker has treated the subject mainly in a scientific geological manner. We present this paper to the members of the Institute as requested by the Secretary last May, with the object of covering the ground from a more practical and technical standpoint. The notes for this paper were made in a large measure from personal observations, gained chiefly during the past summer on a trip through the field. In connection with this trip we collected a suite of typical hand-specimens, representing the gold-ores and wall-rock from the more important localities. This collection forms a part of the exhibit

Jan 1, 1896

Jan 1, 1925

By Robert Archer

IT is now well known that the structure of aluminum-silicon alloys can be refined in a rather remarkable manner, with consequent improvement of physical properties, by certain treatments applied to the molten metal shortly before casting. The differences between the treated and the untreated alloys are so marked that special terms are used to distinguish them, the untreated alloys being referred to as "normal" and the treated alloys as "modified." The first practical method of accomplishing this result was that of A. Pacz,1 which consists in treating the molten metal with a, salt flux of which the, active ingredient is sodium fluoride. The result can also be brought about, and in a more economical manner, by the addition of small quantities of metallic sodium (or potassium) to the molten alloy shortly before casting.2 The action of the Pacz flux evidently consists essentially in the production of free sodium by the reaction of sodium fluoride with aluminum. The changing of a normal alloy to a modified alloy is referred to as "modification' and any process for accomplishing this result is a "modifying" process. Modified aluminum-silicon alloys were introduced several years ago, and it has been demonstrated both in the laboratory and in commercial practice that it is no simple matter to produce castings having the maximum or nearly the maximum properties which under favorable circumstances can be obtained. The alloys are rather sensitive to small changes in chemical composition, and the modifying process must be carried out in a very particular manner to obtain the best results. Extensive experimental work has been carried out in the laboratories of the Aluminum Company of America with the object of determining the conditions that must be observed to make these alloys of the greatest possible

Jan 2, 1926

By D. Harrington

ANNUAL or necessary inspections and investigations of coal mines for various purposes were made possible through the Federal Coal Mine Inspection Act of May 7, 1941, which authorized entry to the Secretary of the Interior through the Bureau of Mines. Primary object of these inspections is to obtain information pertaining to health and safety conditions. Among the purposes for which the data are to be used, are annual reports to Congress, the publication of inspection reports, and the compilation and publication of statistics. The act states that inspections and investigations shall be made by employees of the Bureau of Mines, who shall co-operate with other bureaus of the U. S. Department of the Interior, as well as with the official mine-inspection, safety cr health agencies of the several states and territories. The act specifies that a coal-mine inspector shall have "the basic qualifica-

Jan 1, 1946

By Charles R. Keyes

the leaching of near-by rocks, had had no other result than to bring out from obscurity three certain features of practical lmport, all the labor of that controversy would have been well expended. These three points are : (1) a clear distinction between the vadose and the profound zones; (2) a determination of the manner in which the latter may be invaded by conditions of the former; and (3) an establishment of the general truth of the lateral-secretion theory when vadose conditions prevail, and of the. ascension-theory under profound conditions. In the practical consideration. of ore-deposits these generalizations are fundamental. Their wider application must be productive of great industrial advantages. Of first importance in the broader scientific survey of ore-genesis is the recognition of a sharp distinction between vadose and profound conditions. To many who listened to Professor Posepny's remarkable paper, read at the Chicago session of the Institute during the Columbian Exposition in 1893, this seemed, as Dr. S. F. Emmons has already observed, its most valuable and suggestive feature. Notwithstanding Posepny's implications to the contrary, and his vigorous berating of Sandberger's views, the immediate and lasting .effect of the . argument was really to strengthen greatly Sandberger's position. For it completely and sharply separated the lateral-secretionists from the ascensionists, raising the sphere of the former bodily above the line of permanent water-level and at the same time confining .the sphere of the latter to regions below that horizon. A little later, Professor Van Rise showed in some detail how meteoric waters may deeply invade the profound zone and carry vadose conditions into it. The zonal limitations of two great and apparently opposed agencies being thus definitely fixed, it is found that neither of the theories based thereon is susceptible of general application. If the generalizations of the lateral-secretionist be propounded solely for vadose conditions, we are able to agree with all of his more-important contentions; while there is general acquiescence in the views of the ascensionist if their application be restricted to the profound zone. Of the ore-bodies of the world that are mined to-day, the majority are essentially vadose in origin, and probably originated

Jul 1, 1910

By Thomas V. Falkie, Robert Stefanko

Much has been said and written recently about the manpower problem in the mining industry. The coal segment of the industry has been scrambling to staff and man its companies and operations in order to accommodate the current boom, and there are some interesting side- lights and developments which deserve further attention from coal mining people. This column will deal with the manpower problem in general and the plight of the professional-the mining engineer-in particular. At this point in the game, it is desirable and perhaps necessary to ask ourselves if there really is a manpower problem and, if so, how serious it is. Suprisingly, there are varying and conflicting answers to this question. If we are talking about warm bodies, then in most mining areas there is no problem. If, however, we are talking about skilled or trained people-at all levels-there are apparently serious shortages, especially in the coal industry and in the U. S. Bureau of Mines. To define quantitatively the present and future need for mining professionals is a formidable task, to say the least. Without pretending that these figures are anything but an educated guess, we feel there is an immediate need for about 1000 mining engineers right now and a continuing need for about 300 mining school graduates per year (double last year's number) for the next ten years in order to take up the slack, provide for attrition and maintain a normal growth rate. Mining companies, large and small, are just now beginning to realize that the industry is undergoing a revolution, It is no longer possible to design, build and operate coal mines by the "seat of the pants." Production demands, the new health and safety law and the inevitable new legislation on surface mining will require more engineering, more planning and new technology. There are mine operators who need mining engineers and don't even know that they need them. This could mean rough going for the small operator. It surely means that there will be a trend toward increasing the ratio of technical to nontechnical employees and the ratio of technical employees to dollars of capital towards levels comparable with other highly mechanized industries.

Jan 1, 1971

By Harvey S. Mudd

WHEN talking about Europe it is well to endeavor to keep politics and economics apart but they have become so intermingled in recent years that the discussion of one topic inevitably leads to the other. Economic influences formerly prevailed over politics but today national and international economies are governed by political forces. Commerce in raw materials, food, and manufactured products is now so restricted by governmental controls that the capacity of the world to produce and to consume, to exchange goods and to pay for them, cannot be gauged by the past or predicted by a multitude of experts. In prewar days there were some yardsticks but today there are none. Thus it is hazardous to make forecasts, for in all fields of human effort the world has been cast upon an uncharted sea.

Jan 1, 1947

By Moshe Sheinkin, Douglas E. Julin

Large tonnage operations face many problems in adequately planning ahead for future years production. In order to maintain desired levels of production, such problems as source of tonnage, man- power and equipment requirements, tailings disposal and water requirements must be anticipated. Of course, before any of these problems can be analyzed, daily tonnage requirements and its source must be determined. Looking ahead for one year or even two or three is usually not sufficient time to adequately prepare an area for production. Because of the sequence of mining and the multilevel nature of the 42,000 tpd Climax mine in Colorado long-range planning must be on a ten-year basis. By using a ten-year base, adequate time is allowed to gain access and prepare a new level for production. Usually eight years will be required for this phase of the initial mine preparation. Once production has been started on a level and access to the area is available, three years is usually sufficient to prepare a new block for production as long as it follows in the normal sequence of mining.

Jan 4, 1967

By J. Brian Eby

As is generally understood, the word geophysics means literally ?the physics of the Earth? and the science of geophysics is therefore that which treats of the study and measurements of the various physical properties of the Earth. The broad and general study of the elastic, the gravimetric. or the magnetic properties of the Earth as a whole belongs to the general science of geophysics. The detailed application of this science to rocks of shallow depth and in small areas for the purposes of ascertaining data on their character and structural attitude gave rise to the present well-known science of ?applied geophysics.? Since the discovery of enormous new quantities of oil, gas, and sulphur has been by far and wide the principal benefaction of geo-physics in the United States, this paper will refer only to geophysical methods employed in the search for these particular minerals. The application of methods and appliances originally used for geophysical research to the solution of the practical problems of finding new oil-fields, plus the counterflow or new and highly refined techniques and Instruments from the company and consulting geophysical research laboratories and into non-economic geophysical research, has provided another case of that gen-eral cycle of events which is familiar to all scientists. That this closed-circuit flow or scientific current has been tremendously important to the whole science of geophysics is probably well known to all members of this audience, but the gen-eral status of the exploratory geophysical arts as now used In the search for new oil-fields, the scales on which different methods are being used, the magnitude of the costs involved, and the far greater magnitude of the practical results achieved may not necessarily have come so directly to your attention. It is, I understand, for this reason that this paper has been sug-gested, and I shall seek to provide the information requested by using as case-illustrations those changes in the oil-reserve picture for the United States as a whole, and for the Gulf Coast, California, and Illinois Basin regions in particular, which have occurred in the period of the past 17 years, during which time oil-field discoveries have proceeded at a rate which served to build up known and readily-available (or proven) oil supplies to a reasonable figure, and have dispelled the fears of a serious oil shortage during any period for which valid fore-casts can be made. Not that geophysical-prospecting methods have alone been responsible for this transformation, but they have an indispensable and leading part in the picture of exploration and production-to which geophysics, geology, engineering, and general technical progress have jointly made contribution. So far as the United States as a whole is concerned, its total proven, probable, and possible oil reserves (discoverable and recoverable by then-known methods) were estimated at about nine billion barrels in 1920, whereas proven reserves alone are now com-puted at about 16 billion. In 1920 the driller in ?wild-cat? territory was faced with the knowledge that for every new oil-field opened by a successful well, from 20 to 100 unsuccessful wells would have to be drilled and, in some territories, that the chances for a discovery were really less than one in 100 for new drilling, in contrast to which may be cited the record for the past year in parts of Louisiana where the 67 wells drilled opened 16 new oil-fields, that is to say, where the score of hits to misses was increased to approximately one out of four.

Jan 1, 1940

By E. E. Schumacher

IN a laboratory devoted to the furtherance of the science of communication, the breadth and variety of the problems encountered are challenging to a metallurgist. In my own long association with the Bell Telephone Laboratories, our metallurgical group has dealt with a vast number of alloys, both ferrous and nonferrous, and with many materials in the border range of metallic properties., The objectives of our design engineers embrace every phase of telephony, and the properties they desire in metals are generally unusual, frequently unique, and often conflicting. Commercial alloys have not always been available with properties to meet a special requirement in the telephone plant, and many alloys have had, therefore, to be custom-made. Anyone who has had the opportunity to observe the results of tests of all types on numerous such alloys, both commercially and specially produced, or who has taken part in the development of an alloy of some necessary, but new or unusual combination of properties, could not fail to be impressed by the frequency with which a desired goal has been reached or adequately approached through the presence of decimal quantities of alloying elements. Nor could One fail to be struck by the occasions when, conversely, of a minute amount Of impurity element has rendered an alloy useful. It is no exaggeration to state that the content be- hind the decimal point often spells success or fail-ure, and the critical content is sometimes far to the right of the decimal point as I shall later illustrate. The great effects of small additions have long been recognized and have, in fact, been described by many investigators. The importance of the minute, however, cannot be overemphasized. Therefore, in this discussion, I propose to illustrate for you some of the startling instances, drawn primarily from our own experiences, wherein small, even vanishingly small, proportions of stranger elements in otherwise common aggregates have com-pletely changed the customary pattern of behavior. No one property has a monopoly as to being dis-proportionately affected by minor elements. Nearly all properties are affected, but there is time here to include only a selected few. I have chosen, there-fore, three of general interest: strength, magnetic, and electrical properties. I shall inquire into both the mechanisms and consequences of these disproportionate effects and try to share with you the fascination and challenge of this field. Strength Properties of Lead and Lead Alloys To illustrate the effect of the minute on strength properties I have selected lead and its alloys, with which we have worked extensively for many years. Lead has the advantages of being available in quantity in a state of high purity and of being fairly easy to melt and fabricate without contamination to any extent detectable by the spectrograph. It has the interesting disadvantages of recovery and recrystallization at room temperature. Whether I

Jan 1, 1951

By John N. Dew, William L. Martin, `

This paper describes the results of a laboratory investigation conducted to obtain data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. Air and fuel requirements, rates of advance, com-bustion temperatures, and coke and fluid distributions are presented. The mechanism of oil recovery by in stiu combustion is discussed. Five crude oils ranging in gravity from 10.9 to 34.2"' API were prodrrced from a semiadiabatic, uncon-.solidnted sand pack by in situ combustion. Experimental conditions were varied over a wide range in order to determine the inter-relation-.ships of process variables. The mini-mum air flux requirement for self-sustained combustion was found to he less than 10 scf/hr-ft'l. The rate of advance of a self-sustained combustion zone was found to be nearly proportional to the air flux at the combustion front. The effects of presrure and injected air flux were studied in a series of experiments using a 21.2" API crude. A minimum air require-ment was observed at an air .flux of 20 scf/hr-ft'. The oil saturation con-sumed as fuel averaged 5.5 per cent of pore volume. The effect of air pressure was, found to be .small for experiments having high combustion eficiencies. This study should promote a better understanding of the problems and mechanisms involved in labora-tory investigations and field applications of the in situ combustion pro-cess. The data presented will be use- ful in the interpretation of results of field tests. When tempered with volu-metric sweep efficiencies, the data can be used in making preliminary economic appraisals of the process as applied to reservoirs containing high porosity unconsolidated media. INTRODUCTION The purpose of this work was to obtain laboratory data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. In situ combustion basically consists of (1) injecting air into a reservoir through selected input wells to create an air sweep through the reservoir, (2) igniting the crude at the injection well, and (3) propagating the combustion front through the reservoir by continued air injection. By this means, oil is swept toward producing wells in the area. The fuel for combustion is supplied by heavy residual material (coke) which has been deposited on the sand grains during distillation and cracking of the crude oil ahead of the combustion front. Recovery of petroleum by a combustion or heat wave process is not a new idea. F. A. Howard was granted a patent in 1923 on a process in which air and a combustible gas were pumped into an injection well and ignited.' Russian engineers reported on field experiments with a crude oil gasification process in 1935'. Other known early field tests include those conducted near Bar-tlesville and Ardmore, Okla., in 1942." More recently completed field tests include an inverted seven-spot by Sinclair Oil Co. in the Delaware-Childers field, Nowata County, Okla.'; a three-well and an inverted five-spot test by Magnolia Petroleum Co. in Jefferson County, Okla."."; and a test by California Research Corp. in the Irvine-Furnace field in Kentucky. The Worthington Corp. has completed a test in cooperation with the Forest Oil Corp. in Clark County, 111.l Several field tests are now in progress. Sinclair has acquired a 600-acre lease in the Humboldt-Chanute field, Allen County, Kans., and is under way with a large-scale operation. Three field tests are under way in California. The General Petroleum Corp. is conducting an inverted five-spot pattern test in the South Bel-ridge field in Kern County under a cooperative agreement with 11 other companies, including Continental Oil Co. California Research Corp. is conducting a four-well pattern test in Midway-Sunset field near Maricopa, and Richfield Oil Corp. is under way with a test in the Ojai field in Ventura County. Although the published information is valuable concerning results of field tests, little laboratory data other than that reported by Kuhn and Koch5 are available to aid in appraising the tests from a technical or economic standpoint. Engineering data needed to evaluate the process include the amount of air required per barrel of oil recovered, minimum injection rates which will support combustion, rates of advance, air required per unit volume of reservoir cleaned, amount of oil recovered, and amount of oil consumed as fuel. The present laboratory investigation was undertaken to provide these data for that portion of the reservoir swept by the combustion zone. The first phase of this investigation was exploratory in nature and was conducted at injection pressures less than 100 psig. Data were ob-