Search Documents

By F. F. McINTOSH

STEEL is a general name applied to the alloys of iron and carbon. These alloys always contain , other elements such as manganese, silicon, sulfur, and phosphorus. Manganese and silicon are usually considered to be alloying elements. Sulfur and phosphorus are regarded as impurities. Tradition has damned them both and, in addition to classifying them as impurities, has established the general impression that many of the ills of steels are the result of the presence of one or both of these elements. Metallurgists are inclined to question the soundness of this tradition. The fact that one blast-furnace plant is devoted entirely to the production of ferro-phosphorus which is used to rephosphorize basic open-hearth steel, and that sulfur is added to many heats of steel, indicates that these so- called impurities might also be classed as alloying elements, and that the tradition which damns them may not be altogether fair and well founded. A critical search through the technical literature on the effect of phosphorus on steel will disclose many references to its harmful effect. Most of these are general in character, but there has been a strong tendency to accept this traditional belief in the harmful effect of the element.

Jan 1, 1926

By L. C. Glenn

IN the preparation of this paper the writer has drawn freely upon the writings of Orton, Munn, Shaw, Mather, Miller, Hoeing, St. Clair, Jillson, and others, as well as upon his own personal knowledge of the fields of both states. It is to be regretted that certain data gathered by him and his assistants last fall are not available for publication. OIL IN TENNESSEE A few wells drilled for brine for salt making in Tennessee between 1820 and 1840 obtained oil, but no definite search was made for oil until just after the close of the Civil War. Active drilling was then begun in Overton and counties southwest of it on the eastern half of the Highland Rim. A number of strikes were made at shallow depths in the basal part of the Mississippian but the wells were soon exhausted and abandoned. Drilling was revived, about. 1892, when the Spurrier district in Pickett County was developed and was followed by the Riverton district in the same county in 1896. A pipe line was laid from the Wayne County, Ky., fields and about 60,000 bbl. of oil were run before a very heavy slump in the production, a failure to find an extension of the field, and excessive local taxation caused the removal of the pipe line in 1906. There was then no production in Tennessee until the discovery, in 1915, of oil near Oneida, Scott Co., at about 950 ft. (289 m.) in fissures in the Newman or St. Louis limestone. This field, however, soon failed and was abandoned. In 1916, oil was found at Glen Mary, Scott Co., in the Newman limestone at a depth of 1232 ft. (375 m.) A number of wells have since been drilled there, some of which were dry while others, close by, were producers. The largest one yielded, at first, about 340 bbl. per day and produced for several months, when it suddenly went dry. Several of the first wells began at 6 or 8 bbl. per day and are still maintaining that

Jan 1, 1920

By H. K. Shearer

North Louisiana (including all townships north of the Louisiana base line) had a year of normal development in 1940, marked by the discovery of two shallow oil fields producing from the Wilcox formation in La Salle Parish and a large increase in drilling in the old Caddo shallow field. This renewal of shallow drilling activity led to a somewhat unexpected increase in the number of wells drilled, although the total footage and average depth continued to decline, as in several preceding years. Well completions and depth statistics for 1940, with previous years for coinparison, are as follows: Wildcat producers in 1940 include the discovery oil wells in the Olla and Nebo fields; also three gas wells in the vicinity oi the Olla field and a shallow gas well, which opened a new field or extension in the Greenwood area of Caddo Parish. This table illustrates the lack of important deep discoveries since 1937, in which year the Rodessa, Lisbon and Cotton Valley fields were being actively developed. Operators have been forced to return to the old type of shallow drilling, which necessarily means smaller producing wells. Oil production in 1940 was 24,381,760 bbl., a decrease of 867,880 bbl. from 1939, or 3.44 per cent. The newly discovered fields of La Salle Parish produced over a million barrels, and other increases worthy of note were at Cotton Valley, Caddo, Sligo and Sugar Creek. The greatest decrease was again at Rodessa, although this remains the principal producing field. Geological Names Revised Deep drilling during 1940 did not provide a great deal of new geological information. However, by agreement of a majority of the members of the Shreveport Geolog- ical Society, the names of some of the Lower Cretaceous formations have been revised in the interest of greater clarity and in order to make the descriptions agree better with the facts discovered in recent years. The geological section is discussed in detail and reasons for changes in nomenclature are stated in a recent publication by Ralph W. Imlay. Although not yet in universal use among field men, the new names are employed in this report and accompanying tables, as

Jan 1, 1941

By H. K. Shearer

North Louisiana (including all townships north of the Louisiana base line) had a year of normal development in 1940, marked by the discovery of two shallow oil fields producing from the Wilcox formation in La Salle Parish and a large increase in drilling in the old Caddo shallow field. This renewal of shallow drilling activity led to a somewhat unexpected increase in the number of wells drilled, although the total footage and average depth continued to decline, as in several preceding years. Well completions and depth statistics for 1940, with previous years for coinparison, are as follows: Wildcat producers in 1940 include the discovery oil wells in the Olla and Nebo fields; also three gas wells in the vicinity oi the Olla field and a shallow gas well, which opened a new field or extension in the Greenwood area of Caddo Parish. This table illustrates the lack of important deep discoveries since 1937, in which year the Rodessa, Lisbon and Cotton Valley fields were being actively developed. Operators have been forced to return to the old type of shallow drilling, which necessarily means smaller producing wells. Oil production in 1940 was 24,381,760 bbl., a decrease of 867,880 bbl. from 1939, or 3.44 per cent. The newly discovered fields of La Salle Parish produced over a million barrels, and other increases worthy of note were at Cotton Valley, Caddo, Sligo and Sugar Creek. The greatest decrease was again at Rodessa, although this remains the principal producing field. Geological Names Revised Deep drilling during 1940 did not provide a great deal of new geological information. However, by agreement of a majority of the members of the Shreveport Geolog- ical Society, the names of some of the Lower Cretaceous formations have been revised in the interest of greater clarity and in order to make the descriptions agree better with the facts discovered in recent years. The geological section is discussed in detail and reasons for changes in nomenclature are stated in a recent publication by Ralph W. Imlay. Although not yet in universal use among field men, the new names are employed in this report and accompanying tables, as

Jan 1, 1941

By George W. Sheary

Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Company's Bethlehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with 3/4-in. slotted vibrating screens. The ore is washed and screened in the mill and the plus 1/4 in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30 in, cyclones, to 1% on 100 mesh and 65% minus 325 mesh. The ground ore is magnetically concentrated by three-drum permanent type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50 ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% plus 1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica.

Jan 5, 1962

By J. H. Nead

OBJECT THE experiments herein described were undertaken with a view to investigating thoroughly the influence of carbon on the tensile and impact physical properties of carbon steel. The original comprehensive plan included investigation of a series of steels with varying carbon contents over a wide range of heat treatments. These were to be studied as to their static tensile qualities, and also their resistance to shock as measured by the Charpy impact bending test. A thorough metallographic examination was likewise included in the schedule. The Charpy tests and the metallographic examination have not been completed to date, and are accordingly withheld for another report. All heat treatments, however, have been made, and the static tensile tests have been completed. A description of the procedure of the experiment and the results thus far obtained are therefore reported herein. CONCLUSIONS No attempt is made to draw general conclusions from these experiments, but the curves and the data are submitted as being of general importance and wide applicability.

Jan 12, 1915

By Worthen Bradley

A BETTER understanding of what is happening in the domestic quicksilver industry, and what is likely to happen, can be had after reviewing some of the highlights of the past four years. Hitting the high spots in chronological order, they are: February 1939-Army and Navy Munitions Board starts investigation on civilian and war needs of certain "strategic materials," including quicksilver, with a view to recommending stock piles. Every known producer is canvassed by the end of the year.

Jan 1, 1942

By Howard Reiss, C. S. Fuller

A theoretical and experimental study has been made of those interactions between holes and electrons which influence the solubilities of donors and acceptors in semiconductors. The major portion of the work concerns the solubility of lithium in silicon doped to varying degrees with boron. This solubility increases with increasing boron content in a manner predicted by theory and exhibits the expected temperature dependence. A qualitative experiment in germanium is described which demonstrates, in accordance with theory, that doping with a donor decreases the solubility of another donor. SEVERAL authors have discussed the possibility that holes and electrons behave like chemical entities and influence the solubilities of ionized impurities, Wagner was the first to invoke this concept in connection with his studies on nonstoichio-metric oxides. He used it again in explaining the solubility of hydrogen in molten binary alloys. In a theoretical paper,' Reiss drew attention to the fact that solutions of impurities in semiconductors

Jan 1, 1957

By G. D. Cody, D. S. Beers, B. Abeles

The thermal diffusivity (thermal conductivity divided by specific heat) of Armco iron has been measured over the temperature range 30º to 1025ºC. The results are in good agreement with the thermal diffusivity computed from published values of thermal conductivity and specific heat, except near the Curie point and at the a to y phase transition, where the measured diffusivity undergoes rabid variations. The differences observed are ascribed to a rapid variation in the electronic thermal conductivity near the Curie point, and a decrease in the lattice thermal conductivity, at the a to ? phase transition. A major difficulty in measuring the thermal conductivity of materials at high temperatures is the determination and elimination of radiation losses. It has been shown, however, that in measuring thermal diffusivity D (thermal conductivity/specific heat) radiation losses can be taken into account exactly.' In order to test the performance of a newly designed apparatus for measuring thermal diffusivity of solids,' we measured Armco iron to an accuracy of 2 pct in the temperature range 30" to 1025°C. This material was selected since both the thermal conductivity,3'4 k, and specific heat,5 C, are known accurately in this temperature range and thus the measured values of D could be compared with D computed from the pub-

Jan 1, 1962

Each spring most secondary schools select their best student science exhibits, prepared during the preceding academic year, and send them to regional "Science Fairs", which now number over 220. Winner-finalists of these regional contests are then sent to the annual National Science Fair, conducted by Science Service, a non- profit institution for the popularization of science, for final judging. (The Fair is now known as the "National Science Fair-International" because of participation by finalists from Japan, Thailand, Germany, France, Sweden and Canada.) For the first time since the Fair was started in 1950, AIME participated in the awards presentation. Held this year in Baltimore, Md., from May 5 to 9, five members of AIME's Washington, D.C., Section consented to represent the Institute as judges. They were: Marlin J. Ankeny-Director, Bureau of Mines, U.S. Department of the Interior. Kenneth N. Weaver-Director, Maryland Department of Geology, Mines, and Water Resources. William Harper-American Petroleum Institute. Vice-Chairman, Washington Section, AIME.

Jan 7, 1964

By Leonard Austin

WHAT Colonel Dwight says regarding the treat-ment of oxidized ores1 holds true also of the silver-lead smelting operations in Utah. The ore sought for was such as would, with appropriate fluxes, yield slag, and "lead bullion," as the lead reduced from the ore and carrying its gold and silver, was called. No matte, and probably little or no speiss, was yielded, and hence there was nothing to roast, either of ore or matte. But, by 1880, when I first took hold in smelting, there was quite a production of matte at the works of the Ger-mania Smelting and Refining Co., Utah, because, by that time, ores containing some pyrite and galena were being smelted. This was due, as at the Grant Works, Denver, to the more attractive price paid for the treatment of such ores. The matte, containing about 5 per cent. copper, was accordingly heap-roasted and returned to the blast furnace for the recovery of its contained metals. By this time there had been built a long-bedded, hand-rabbled reverber-atory roaster with a hearth of about 40 by 10 ft. in size, and in this matte and ore, crushed at the sampling mill, was treated. When, in 1892, I took control of this works, called& now the Germania Lead Works, three other roasters had been added, but the prac-tice of heap-roasting continued. This had the merit of needing no equipment, and of doing good work, because the pieces that were imperfectly roasted went back upon the next roast heap. At this time, when some suitable lump ore was obtainable, I roasted in heaps, in a satisfactory way. By 1892, the Bruckner cylinder roaster had been installed, which, compared with the reverberatory roaster, reduced labor. As such a cylinder revolves, a talus of ore is formed within it and at the same time fresh surfaces are exposed to the air, but the trouble was that the air did not reach to the bottom of the cylinder. This we corrected by placing a steam jet at the fire-box end, to project the air down-ward upon this stagnant ore, thus increasing the speed and completeness of roasting without at the same time increasing dust formation. The firing, if skilfully done, gave a somewhat sintered product, but with certain ores a slight access of heat over the normal would cause accretions to form within the cylinder near the fire end. These could be cut off by running back the fire box and barring off the crusts. It was in 1895 that the Bruckner cylinders at the Arkansas Valley plant, Leadville, were giving unsatis-factory service and I was called in to investigate. The steam jet was put in use as at the Germania Lead Works, but we found that, due to the altitude (10,500 ft.), combustion was feebler than at sea level or even at 4000 to 5000 ft. Later it appears, as Colonel Dwight states, that R. D. Rhodes and Mots sought to increase the air supply by admission through perforated tiles, but the trouble was due to the air itself.

Jan 8, 1922

Lead-zinc production in Canada accounted for 19% of the total value of metals and minerals produced in 1976, says Keith C. Hendrick, president of Noranda Sides Corp. Mine production of recoverable zinc w as 1. 158 million toils of 27.4% of free world production in 1976. Slab zinc pro¬duction was placed at 472,000 tons that year. Canadian mine production of recoverable lead was 247,000 tons or 10.6% of the free world production. Refined lead that year was at 177,000 tons.

Jan 11, 1977

By H. E. Ellis, O. L. Patterson, Granville Dutton

A large-scale water-injection program for the Holt Bryant reservoir of the Delhi field has been established by means of the new automatic multi-pool analyzer. The objectives of this program were to increase reservoir pressure and eliminate a cross-dip gradient of 200 psi. Pressure increases during the first 15 months of operation have allowed for increased oil production rates of 2,600 BID or 25 per cent. To determine the required water injection it was necessary to predict natural water influx ram. Elimination of the pressure gradients required the water-injection program to account for the fluid migration and pressure interaction between segments of the reservoir. An integral part of the ana1ysis included the determination of in-place volumes of oil and gas. The operation of the automatic multi-pool analyzer in determining the water-injection program is described. New features of the analyzer inc1ude an automatic maferial balance analog and a leart-squares computer for determination of unknown reservoir properties. Operational procedures are sufficiently simple to allow direct use by reservoir engineers on a routine basis. The rapidity and accuracy with which problems may be solved permit repeated ana1yses as a check upon reservoir performance. INTRODUCTION This paper describes the use of a new analog com- puter in determining the optimum injection program for a complex reservoir. The Holt-Bryant (Fig. 1) is the major reservoir in the Delhi field of Louisiana. Production is from the Tuscaloosa at subsea depths of 2,970 to 3,286 ft. The sand dips to the south and southwest from three to five degrees. The reservoir is approximately 12 miles long and varies in width from 1/2 to 2 miles. Various calculations have placed the initial volume of oil in-place in the wide range of 275 to 355 million STB. Two small gas caps were initially present in the reservoir. The Holt-Bryant reservoir was discovered in Dec.. 1944, and was fully developed with 188 producing wells by 1948. After development was completed, an east-west pressure gradient began to establish itself. This

Jan 1, 1957

By George Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro-posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bitu-minous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By G. Sachs

According to Tammann,' the explanation of the effect of mechanical deformation in producing changes in the properties of metals is one of the most important problems of physical metallurgy, taking rank with the study of the constitution of alloy systems; and this problem has long attracted the attention of practitioner and scientist alike. Its solution was not advanced materially until Tammann2 set up his translation hypothesis with its crystallographic basis, while other hypotheses, such as the amorphous metal hypothesis of Beilby3 and Rosenhain,4 have been shown by more intensive studies to be less and less satisfactory. The principles of the Tammann translation hypothesis have proved to be useful even up to today and in spite of all of the recent accumulation of experimental data, while the differences of opinion which have arisen relate to the extent to which the hypothesis accounts for the observed changes Ïn properties and to what extent further assumptions are necessary. Stimulated by the proposals of Tammann, there soon developed a lively experimental activity which aimed at the elucidation of the structural or crystallographic changes produced by the mechanical deformation of metals. Parallel movements of crystal "blocks" along definite crystal slip planes had already been observed by Ewing and Rosenhain5 in 1900, in metals which had been moderately deformed but without shedding light on the crystallographic nature of the processes accompanying more severe deformation. The solution of this important problem was not advanced until a much later date, or until the methods of X-ray crystal analysis had become available. Shortly after the discovery of the diffraction of X-ray by crystals, symmetrical diffraction effects were

Jan 1, 1931

By H. M. Varner

Under sponsorship of the US Bureau of Mines and the Department of Energy, a new type of rotary rock drill was developed by The Bendix Corp. Originally developed for the production of holes for the installation of longer than seam height roof bolts, the flexible drill is a useful tool for many drilling applications. It allows hands-off or remote production of holes for increased drilling speed and greater operator safety in any strata suitable for rotary drilling. This paper discusses various applications and experience for the flexible drill system in coal, metal/nonmetal mining, and for civil engineering uses. Manual, remote control, and automatic roof bolter modules are also discussed.

Jan 1, 1984

By Lewis Reeve

As part of a program of investigation of the properties of electric arc welds carried out in the laboratories of the A. 0. Smith Corporation, considerable work has been done on the determination of the oxygen, nitrogen and hydrogen content of different types of weld metal, employing for this purpose the so-called "vacuum fusion method." It is the purpose of this paper to describe certain improvements that have been introduced in this method of determining the gas content of metals, with particular references to the steel specimens examined in this investigation. The method and apparatus used at the beginning of the investigation were essentially those of the Bureau of Standards as described by Vacher and Jordan.' Later a number of changes were introduced which resulted in more rapid evacuation of the graphite crucibles employed and which enabled larger volumes of gas to be dealt with than could be handled conveniently in the Bureau of Standards equipment. In addition, the analyzing of the gases evolved from a melt in the same apparatus as collected was abandoned in favor of analysis outside the equipment using standard methods of gas analysis. The time required for gas analysis in the apparatus itself, as described by the Bureau of Standards, was found to be considerable, and during this time the rest of the equipment was tied up, preventing its use for the analysis of further steel samples. As a result of the modifications introduced, the time required for the analysis of a steel sample for gas content was reduced from about 8 hours to less than 3 hours. Subsequently, the whole procedure of melting the sample and collecting the gases evolved was modified so as to enable a distinction to be drawn between the easily reducible oxides such as iron oxide and the more stable oxides such as silica and alumina. At the same time evidence was obtained indicating the probable existence in the steels of other nitrides than those of iron alone and making possible their quantitative etermination.

Jan 1, 1934

By Robert Mehl

IN examining the progress of metallurgical science, the critic must remember that most of our present knowledge of metals and alloys has been accumulated through the needs of industry and commerce rather than through the desire and efforts of a large body of scientists interested primarily in developing a science of metals. The progress of metallurgy, scientifically speaking, has been irregular, and little given to the exhaus-tive exploitation of important scientific fields. The experienced engineer now recognizes the need for the development of the basic science upon which his engineering rests. In addition to the increase in knowledge which results from the normal requirements of industry, a development of the basic science of the behavior of metals and alloys is as desirable in metallurgy as in any other branch of science and engineering. The continued growth of the science of metals-as of every other science-requires studious attention to the principles that underlie the behavior of matter, with the result that knowledge in the several fields of interest should continue to increase. Among the various subjects recognized as important in physical metallurgy few have a wider significance than that of diffusion in solid metals. The phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this, the process of diffu-sion is of first importance practically. The formation of alloys by the annealing of mixed powders, first practiced by Faraday and Stodart81 in 1820 and in more recent years investigated by Masing187,189 and others, has led to the development of special alloys like Carboloy, Vascoloy-Ramet, Genelite, Elcon68, and has recently been applied to the production of noble-metal alloys for electrical contacts"'.

Jan 1, 1936

By C. Feng, C. Elbaum

AN investigation of the fracture plane of titanium, containing 0.5 wt pct to 1 wt pct 0, was recently carried out by fracturing large-grain specimens in a tensile jig at room and liquid air temperature. The experiments were carried out on strip specimens 3 to 5 mm wide, 2 mm thick and about 100 mm long. The specimens consisted of several grains, each occupying the entire cross section of the strip and extending over a length varying from 5 to 20 mm. These specimens were prepared by a method described elsewhere.' The identification of the fracture plane was possible in twelve of approximately thirty crystals investigated. In some cases severe local distortion took place near the fracture and prevented identification of the fracture plane. On, at least, three occasions the fracture propagated in a helicoidal

Jan 1, 1959

By J. Szekely

The paper discusses simultaneous heat conduction and diffusion. These problems may arise in slag-metal kinetics and in connection with rapid heating or cooling of specimens. A mathematical formulation is given and it is shown that the transients due to either the variability of the diffusion coefficient with temperature, or thermal diffusion, are unlikely to be important for molten or solid metals and slags. The negligibility of these effects is due to the large values of the ratio thermal diffu-sivity/molecular diffusivity. In many problems relating to transport-controlled metallurgical kinetics the diffusion process is accompanied by the transfer of heat; large-scale metal refining or metal reduction may be quoted as examples. It has been shown that due to turbulent mixing in these systems the relevant transport phe- nomena are best described in terms of "surface renewal models" which require the solution of the unsteady-state diffusion equation.1-1 Problems involving simultaneous diffusion and heat conduction are also encountered in the laboratory in connection with rapid heating or cooling of specimens. The effect of variable temperature on diffusion may be twofold: a) in the absence of "cross effects" the problem, due to variable temperature, is that of diffusion with a variable diffusion coefficient; b) if the Soret Effect is nonzero, thermal diffusion must also be taken into account in the formulation. Although information is available on thermal-diffusion transients in a steady-temperature gradient,4'5 little work has been done on the effect of unsteady temperatures on either the diffusion coefficient or on thermal diffusion.' In the following a formulation is given and solutions presented with a view of examining the areas where these effects may be important.

Jan 1, 1965