Search Documents

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The addition of nitrogen (0.10 to 0.20 pct) to Fe-Cr-Ni alloys of simulated commercial purity results in a real displacement of the u phase boundaries to higher chromium contents. The effect is small for the (Y + s)? boundary, but is pronounced for the (y + a +s)/(y + a) boundary. Although there is an indication of an exceptionally large shift of the n boundaries to higher chromium contents, especially in steels with nitrogen over 0.2 pct, the major portion of this apparent shift results from the fact that carbide and nitride precipitation cause "chromium impoverishment" of the matrices. The effect of combined additions of nitrogen and silicon to the Fe-Cr-Ni phase diagram is demonstrated also. Nitrogen can nullify the effect of about 1 pct Si in shifting the (y + o)/? phase boundary to lower values of chromium at all nickel levels from 8 to 20 pct. NItrogen can nullify this U-forming effect of about 2 pct Si at the 8 pct Ni level, but not at the 20 pct Ni level. The alloys studied were in both the cast and the wrought conditions. There are indications that the u phase forms more slowly in the cast alloys than in the wrought alloys if both are in the completely austenitic state. The presence of 6 ferrite in the cast alloys accelerates the formation of U. Cold working increases the rate of o formation in both cast and wrought alloys. THE major improvement in Fe-Cr-Ni austenitic alloys in recent years has been in the addition or removal of minor alloying elements to facilitate better control of corrosion resistance, sensitization, and heat resistance. One shortcoming of the austenitic Fe-Cr-Ni alloys, which never has been completely circumvented, is their propensity toward u formation. In the AISI-type 310 (25 pct Cr-20 pct Ni) and type 309 (25 pct Cr-12 pct Ni) steels, sufficient amounts of u phase can form, if service or treatment is in a suitable temperature range, to cause severe embrittlement. Also, there is a growing conviction that this phase may be contributory to some unexpected decreases in the corrosion resistance of certain of the 18 pct Cr-8 pct Ni-type steels. The present paper discusses the effect of nitrogen additions on the location of the (r+u)/d and the (y+a+u)/(y+a) phase boundaries in the ternary Fe-Cr-Ni system, for cast and wrought alloys of simulated commercial purity, and in similar alloys containing up to about 2.5 pct Si. The objective is to define compositional limits for alloys which will not be susceptible to u formation when used near 1200°F (650°C). An excellent review of the early studies of the u phase in the Fe-Cr-Ni system has been compiled by Foley.1 Rees, Burns, and Cook2 have determined a high purity phase diagram for the ternary system, whereas Nicholson, Samans, and Shortsleeve3 are- stricted themselves to a portion of the simulated commercial-purity phase diagram. Both groups of investigators show almost an identical position for the commercially significant (y+u)/y phase boundary. Further comparison of the work of the two groups indicates that, below the 8 pct Ni level, the commercial alloys have a decidedly greater propensity toward u formation than the high purity alloys. The two groups of workers agreed that both the AISI-type 310 (25 pct Cr-20 pct Ni) and the type 309 (25 pct Cr-12 pct Ni) steels are well within the (y+~) region and that the 18 pct Cr-8 pct Ni-type alloys straddle the U-forming phase boundaries. Nicholson et al.3 showed, in addition, that these boundaries shift toward lower chromium contents if greater than nominal amounts of silicon or molybdenum are added. The effect of nitrogen on the location of the s phase boundaries in the Fe-Cr-Ni system has not been known with any certainty. In 1942, an approach to this problem was made by Krainer and Leoville-Nowak,' but at that time they apparently were unaware of the slow rate of s formation in strain-free samples and aged their samples for insufficient times, e.g., 100 hr at 650°C (1200°F) and 800°C (1470°F). For this reason, it would be expected that their (y+ u) /y boundary would be shifted toward lower chromium contents (restricted ?-field) when equilibrium conditions were approximated more closely. Procedure for Studying the Alloys The alloys used were prepared in the following way: Heats of 200 lb each were melted in an induction furnace. A 5 lb portion of each heat was poured into a ladle containing an aluminum slug for de-

Jan 1, 1955

By Alexander R. Troiano, Taylor Lyman

Studies of the transformation of aus-tenite at constant subcritical temperatures have been numerous since the work of Davenport and Rain.' Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of aus-tenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. Experimental Procedure Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8 -in. round bars. Bars were softened at 650' to 700°C. before the specimens were cut. Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examinatioll of partially reacted specimens, Thees specimens were approximately 1/2 by 1/4 by 1/8 in. ill size, specimens of the 9 per cent cr steel were held 10 to 12 hr, at 1200°to 1225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 1/2 hr. at 12ooOC. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. So. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed ill Table I. X-ray Methods Constituents were identified and mar-tensite axial ratios determined from Debye

Jan 1, 1945

By L. L. Swift

AT the present time there are four base metals being used for automotive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows in some types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and preventing overheating and rapid wear of parts. Less plasticity is required in a bearing metal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coefficient of friction. Under most operating conditions the friction depends on the unit pressure of the bearing, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the hearing., The hardness of, the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual constituents was developed to, fill this need. MICROCHARACTER The Bierbaum microcharacter2.3 measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground. so that it is the corner of a cube, and mounted

Jan 1, 1938

By C. E. Julihn

Technology concerns the ways of doing things; mineral technology the ways of performing operations required for obtaining minerals from the earth and extracting their valuable constituents for man's use. At any particular time, technology is relatively fixed, as everyone tries to adopt the way of doing things that has proved most profitable; but improvements evolve from minor changes here and there, and occasion- ally entirely new methods are discovered. Technologic improvement thus characterizes any long-time view of the mineral industries. Its test lies always in reduction of costs; there is no other incentive for the adoption of new methods. Reduction in cost of producing metal from ore decreases, in turn, the amount of metal that must be obtained from ore in order to pay for its production. An advancing technology thus is characterized by utilization of ores of lower and lower grade. A very important result of this is an increase in the gross quantity of metal obtainable at any price level, since the earth's crust contains vast amounts of very low-grade ores and relatively insignificant amounts of very high-grade ores. Technologic advances have, therefore, been the means of rendering the metals both cheap and abundant. Though concern as to possible exhaustion of the world's ore deposits is warranted, it is conceivable that a transcendent technology of the future might supply metal requirements from what we

Jan 1, 1932

By L. L. Wyman

SINCE the presentation, by the writer, of the initial paper on the embrittlement of copper,1 the subject has been investigated further along two separate lines. The first series of investigations involves the "double-deoxidized" copper, while the second series is devoted to single deoxidizers other than those used in the investigations reported upon last year. The object of these experiments is to develop a type of copper that will show the minimum of detrimental effects after having been exposed to alternate oxidation and reduction. The fabrication of this material necessitates the use of alternate oxidizing and reducing atmospheres, at temperatures ranging up to 900° C. Following this treatment it is essential that the soundness and strength of the copper be unimpaired, even in sections of only a few thousandths of an inch in thickness.

Jan 1, 1932

By H. S. Jerabek, Charles S. Barrett, Robert F. Mehl

The precipitation of the nitride Fe4N from the solid solution of nitrogen in a Fe and of the phosphide Fe3P from the solid solution of phosphorus in a Fe both lead to the formation of structures that may be easily identified as Widmanstatten figures, within the meaning of the term as used in this series of papers. A complete solution has been obtained for the figure formed by Fe4N. The structure of Fe3P, however, is not fully known and a complete solution of this figure thus cannot be obtained; nevertheless, a study of this figure has furnished some new information. Precipitation of Fe4N from Alpha Solid Solution of N in Alpha Fe Constitution of System Iron-nitrogen A knowledge of the constitution of the whole of the Fe-N system is unnecessary for this work, though the recent studies by Eisenhut and Kauppl and by Lehrerz have clarified most of the moot points; it is sufficient for our purpose to state that a Fe of high purity dissolves 0.42 per cent of nitrogen in solid solution at the eutectoid temperature, 591' C., and that this solubility decreases at first rapidly and then more slowly until at room temperature the solid solubility amounts to approximately 0.1 per cent nitrogen.3

Jan 1, 1934

By F. R. Archibald, C. M. Nicholson

The present paper may be considered complementary to an earlier contribution on the same subject by F. R. Archibald and C. F. Jackson.1 It is particularly concerned with engineering and technological aspects of the operations at the Harleyville Alumina Plant during its period of operation from January 1945 to July 1946. The plant was built for and operated by Ancor Corporation, at Harleyville, South Carolina, as part of the government sponsored wartime program related to alumina production from domestic raw materials. The main purpose of the program was to secure technical and engineering data, based on actual plant experience, that might serve as a foundation for large scale production of alumina from raw materials other than bauxite. The Harleyville plant was directed specifically to treatment of clays found in very extensive deposits in the Carolinas and Georgia using the lime-sinter process developed by Ancor Corporation. It is considered that the purpose stated above has been served and this paper is to record and discuss some of the more important findings. The main factor in location of the plant at Harleyville was the presence in that locality of a rather remarkable deposit of high calcium limestone. The clay mining operation was centered near Aiken, S. C., and although a rail haul of ninety miles was involved there were, at the time, factors favorable to the Harleyville location offsetting, in part, the cost of transportation of clay, There are, no doubt, locations in the general area where clay and limestone deposits may be found in closer proximity hut they had not been proven up when the project was undertaken. Availability of power from the Santee-Copper development whose high tension line skirted the Property; ready access to rail and highway transportation; the promise, realized in actuality, of ample supply of soft water; and availability of labor supply were other factors of importance. Moreover, the general area has the decided advantage, for this type of operation, of a mild climate. Construction was begun in August 1943, and although stopped for a time priding review of the general situation that fall, it was resumed, albeit with less urgency, and substantially completed by the end of 1944. The total capital cost was approximately $3,460,000 The first alumina was turned out in April 1945 and from then until the plant was closed down in July 1946, the operations followed a succession of periods of production alternating with periods in which minor alterations were made in conformity with experience. Steady improvement was made and at the time Operations were discontinued it was considered that experience and the necessary engineering were in shape for removal of the remaining bottlenecks and a somewhat major revision in one section of the plant. Unfortunately this could not be carried out and it was necessary to discontinue the

Jan 1, 1949

By H. A. Bedworth

ALLOYS of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry1 proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche3 and Corson.4 The constitution of the system has also been recently investigated by Matuyama,5 and in the laboratories of the American Brass Co. by Smith.6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of, the constitution of copper-silicon alloys, the solubility reaches its maximum value, 6.7 per cent. silicon, between 721° and 782° C. At 852° C. the solubility is 5.25 per cent., while at 400° C. it is only 4.1 percent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent. silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By D. Harker, M. J. Murphy

THE mechanism by which age-hardening takes place is still not completely understood. The principal theories range from the extreme of "precipitation-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. PREPARATION OF FORMVAR REPLICAS OF METALLIC SPECIMENS This section is concerned with the techniques that have proved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. It is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work-very fine polishing and etching with very dilute solutions-is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. PREPARATION OF METALLOGRAPHIC SPECIMENS The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch-to approximately the depth necessary for a micrograph at 1000 diameters-usually produces a sur-

Jan 1, 1945

By J. L. Gillson

In a brief summary of the many occurrences of fluorspar in our western states, it is not possible to go into detail in regard to the geology, mining and milling methods, and reserves about individual deposits. Rather a broad review is made of the occurrences and an analysis of how the western deposits may fit into our future domestic economy is presented. General Statement on Fluorspar Situation Fluorspar has been used for years as a flux in the manufacture of basic open-hearth steel, in foundry cupolas for melting pig iron, in the manufacture of opalescent glass and in the preparation of hydrofluoric acid. In 1880 the annual production of fluorspar in the United States was around 4000 tons per year. By 1900 it was up to 21,656 tons and between 1902 and 1908 it averaged about 40,000 tons annually. Prices were then so low, by present standards, that it seems impossible to believe now that mining could have been performed profitably at the price levels then prevailing. In 1890 fluorspar sold at the mines for $6.70 per ton, in 1901 for $5.81, in 1916 for 85.92. When the United States entered World War I, flyorspar production and price skyrocketed; the production reached 263,817 tons in 1918, with prices above $20.00 per ton, and prices were even higher in 1919 and 1920. After 1920, the domestic production fell from the 1918 level to about 125,000 tons annually and the average price dropped back to about $18.00 per ton. By 1935 the average price had fallen to $15.00, but in 1940 with a rising demand the average price of all grades had gone back up to $20.31. Today it is 75 per cent higher than in 1940 and presumably the price of acid grade at .least would be even higher if it were not for price ceilings. The first subsequent year that the domestic production exceeded that of 1918 was 1941, and the 1944 production is expected to exceed 400,000 tons, or over one and a half times that of 1918. In five-year periods, average production and imports were as are shown in Table I. Many people concerned with the consumption of fluorspar believe that the postwar period ahead will show a repetition of price trends of the last such period. They believe that imports will be again an important factor in the available supply and the price will fall back gradually toward the prewar level. The following basic factors are pertinent in analyzing this conclusion:

Jan 1, 1948

By J. L. Gillson

In a brief summary of the many occurrences of fluorspar in our western states, it is not possible to go into detail in regard to the geology, mining and milling methods, and reserves about individual deposits. Rather a broad review is made of the occurrences and an analysis of how the western deposits may fit into our future domestic economy is presented. General Statement on Fluorspar Situation Fluorspar has been used for years as a flux in the manufacture of basic open-hearth steel, in foundry cupolas for melting pig iron, in the manufacture of opalescent glass and in the preparation of hydrofluoric acid. In 1880 the annual production of fluorspar in the United States was around 4000 tons per year. By 1900 it was up to 21,656 tons and between 1902 and 1908 it averaged about 40,000 tons annually. Prices were then so low, by present standards, that it seems impossible to believe now that mining could have been performed profitably at the price levels then prevailing. In 1890 fluorspar sold at the mines for $6.70 per ton, in 1901 for $5.81, in 1916 for 85.92. When the United States entered World War I, flyorspar production and price skyrocketed; the production reached 263,817 tons in 1918, with prices above $20.00 per ton, and prices were even higher in 1919 and 1920. After 1920, the domestic production fell from the 1918 level to about 125,000 tons annually and the average price dropped back to about $18.00 per ton. By 1935 the average price had fallen to $15.00, but in 1940 with a rising demand the average price of all grades had gone back up to $20.31. Today it is 75 per cent higher than in 1940 and presumably the price of acid grade at .least would be even higher if it were not for price ceilings. The first subsequent year that the domestic production exceeded that of 1918 was 1941, and the 1944 production is expected to exceed 400,000 tons, or over one and a half times that of 1918. In five-year periods, average production and imports were as are shown in Table I. Many people concerned with the consumption of fluorspar believe that the postwar period ahead will show a repetition of price trends of the last such period. They believe that imports will be again an important factor in the available supply and the price will fall back gradually toward the prewar level. The following basic factors are pertinent in analyzing this conclusion:

Jan 1, 1948

By Robert E. Allen

The organized curtailment of California oil production is not yet one year old but during its first year it has accomplished so much that it is now firmly established as an agency of economic efficiency. The principle of cooperative curtailment has been adopted by other states and it is safe to say that the principle will continue as long as the demand for petroleum is notably less than the potential production. It' is interesting to note that this same principle of regulating supply to meet demand is now being urged for other industries, such as agriculture and mining. Since Oct. 31, 1929, when curtailment was instituted by the oil producers of Santa Fe Springs and Long Beach in an effort to avert the disaster of ruinously low prices which confronted them, there has been a constant and increasingly effective curtailment program in California. Prior to that time a notable effort toward the restriction of oil production was made under the direction of F. C. Van Deinse during the early summer months of 1929. A considerable reduction of oil output was recorded as the result of this effort, but because of incomplete cooperation and the discovery of still deeper zones at Santa Fe Springs the effort was abandoned; flush field production became unrestrained and prices soon fell to low levels. This initial curtailment movement was educational and experimental. It showed all operators a way out of their overproduction difficulties and developed the principles followed in later curtailment efforts. Thus it was that only a few days after their oil had been reduced to 60 c. per barrel, the operators of Santa Fe Springs got together and agreed to restrict their current production of more than 270,000 bbl. daily to not more than 150,000 bbl. daily. The operators at Long Beach followed the same course a few clays later and agreed to limit their production to not more than 110,000 bbl. daily. The Santa Fe Springs operators chose H. P. Grimm as umpire and director of their proration program. Neal H. Anderson was chosen umpire for Long Beach. Since that time, as the need for curtailment has increased, practically every field of the state has come under the curtailment of these two umpires. Curtailment of the Elwood and

Jan 1, 1931

By C. M. Nickerson

In times of overproduction such as the operators have been struggling against for the past several years it is the practice of the oil industry to shut in certain wells in order to reduce the flood of oil. The purpose of this paper is to present certain variations in production of oil wells when the offset wells are shut in. The scope of the study has been confined to California fields, and more especially to those of the San Joaquin Valley. The accepted definition of a shut-in well is a well where production has been suspended by closing in the casinghead arid tubing or by cessation of pumping. The immediate effect of such a procedure, of course, is to reduce the oil production from the lease, which is the result desired. However, it appears that certain types of wells vary widely in production of oil, gas and gasoline after adjacent wells have been shut in, which variation has a very material effect on the ultimate recovery of oil from the property. The increase or decrease in the oil production itself may not be of sufficient volume to occasion comment, but wide fluctuations in the gas and gasoline recovery under the changed conditions arc of the utmost importance in the future recovery of oil. The scope of this paper includes: (I) the effect on producing oil wells of shutting in offset wells, the wells being studied in three groups arranged according to their relative stages of depletion; (2) probable source of excess gas and the effect on the ultimate recovery of oil; (3) suggested procedure when wells are shut in; (4) methods that could be employed to prevent undue migration of gas from the shut-in area; and (5) the need for future studies of the situation. Three Classes of Producing Oil Wells For the purposes of this paper producing wells in California have been arranged in three groups according to the age of the well, or to the relative stage of depletion of the producing zones. The first group consists of those wells with a high fluid level, or in other words those wells whose fluid levels are a considerable distance above the top of the perforations. This type of well is in the flush period of its life and ordinarily produces

Jan 1, 1929

By R. P. Carreker, J. G. Leschen, J. H. Hollomon

THE external appearance of a crystal which has undergone plastic flow suggests that adjacent blocks of the crystal have glided bodily past one another along the slip planes. However, the great discrepancy between the shear stresses calculated to effect such a movement and those actually observed has for many years stimulated searches for more satisfactory interpretations of the slip process. Appreciable success in these efforts has been realized by assuming the presence in the crystal of various sorts of imperfections and by considering the consequences of the presence of these flaws when stress is externally applied, The theory that has received the most attention recently-that of dislocations-postulates the occurrence of small, mobile imperfections or dislocations which move through the crystal along the slip direction, each dislocation being attended by a local shear displacement of one interatomic distance. Thus only that portion of the crystal through which the dislocation has passed may be said to have slipped, Since each dislocation produces a displacement of only one interatomic distance, an avalanche or train of many dislocations would be necessary to account for the observed displacements of several hundred or thousand interatomic distances. The salient point of the theory of dislocations is the concept that a slip band does not suddenly appear in its entirety. On the contrary, it grows progressively across the slip plane as the individual dislocations successively appear and advance in a train through the crystal. However, the concept of growth is not intrinsic only to the theory of dislocations, since atomistic mechanisms other than that postulated by the dislocation theory can quite probably also describe the growth of a slip band. For instance, a slip band might resemble a disc-like interface that appeared and then grew continuously from a small size, producing a displacement that increased with the size of the disc, Whatever the precise mechanism, the concept of growth is in itself consistent both with -the observed low values of critical shear stress and with the experimental observation that slip bands. frequently do not traverse the entire crystal. The likelihood that slip bands grow implies that they must first be nucleated and that the initiation of slip can therefore be analyzed in terms of the general concepts of nucleation. Indeed, this suggestion was advanced1 several years ago, but the matter does not appear to have been further pursued. Recent advances in the theory of nucleations2,3,4 have encouraged such a treatment of the slip process. As will presently be demonstrated, this approach to the problem not only accounts successfully for the incubation periods that have been observed5,6 to precede slip but also predicts certain transient effects in the deformation process, The existence of these transients apparently has not hitherto

Jan 1, 1948

By Grover J. Holt

A detailed description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E. Hunner, M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,³ it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. † The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and paint rock," directly below the surface material and overlying the ore. Tacenite is the iron formation, a ferruginous chert with inter-bedded slate layers. :'paint rock" is a local term for oxidized slate layers inter- bedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. Stripping Practice Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer, In- the present emergency many operators are forced to forego the economies attained by year-round utilization of paper. and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges Will have to be absorbed.

Jan 1, 1943

By Grover J. Holt

A detailed description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E. Hunner, M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,³ it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. † The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and paint rock," directly below the surface material and overlying the ore. Tacenite is the iron formation, a ferruginous chert with inter-bedded slate layers. :'paint rock" is a local term for oxidized slate layers inter- bedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. Stripping Practice Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer, In- the present emergency many operators are forced to forego the economies attained by year-round utilization of paper. and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges Will have to be absorbed.

Jan 1, 1943

By R. P. Agarwala, M. S. Anand

Using residual activity technique, the diffusion of palladium, silver, cadmium, indium, and tin in alunzinum has been studied in the temperature range of 400" to 630°C. The diffusivities (in units of square centimeters per second) have been expressed as: IMPURITY diffusion in aluminum,1-9 silverand lead5 for cases of low solid solubility of the impurity in the host metal has yielded frequency factors in the range of l0-6 to l0-9 sq cm per sec whereas the activation energy is practically half the self-diffusion activation energy value. From the observed values of frequency factor, activation energy, and entropy of activation, it has been suggested' that these solutes are not diffusing by vacancy or interstitial mechanisms but by a mechanism which should be consistent with such low values of the diffusion parameters (Do and Q). However in spite of extensive work on these types of systems, the mechanism of diffusion is still not well understood. The present investigation on the diffusion of palladium, silver, cadmium, indium, and tin in aluminum has been carried out to throw further light on the diffusion mechanism in systems, where the solid solubility is very low (except for the case of silver). The results are discussed on the basis of solid solubility and the structural changes involved owing to the presence of the solutes in aluminum solid solution. An attempt has also been made to apply the existing theories of charge5-8 and size8 difference between the solute and the solvent. EXPERIMENTAL PROCEDURE Specimens (1/2 in. diam by 3/8 in. high) were machined out of pure aluminum (99.995 wt pct) rod obtained from Johnson Mattheys. They were sealed under vacuum in quartz tubes and annealed at 620° C for several hours; the grains thus developed were sufficiently large to eliminate the possibility of diffusion along the grain boundaries. The flat ends were prepared carefully after polishing as described previously,10 Radioactive nitrates of cadmium, indium, and tin and chloride of palladium containing, respectively, cd115, 1n114, sn113, and pd103 were dissolved in distilled water and mixed with 30 pct acetone. By means of a micropipet a drop of this solution was placed on a smoothly polished and lightly etched surface of the specimen. Due care was taken to see that the solution spread uniformly on the surface of specimen without trickling down its sides. Radioactive silver was elec-trodeposited using a AgCN-KCN bath. The amount of sample deposited in all the cases was not more than 0.1 µ thick. The samples were then sealed in quartz tubes in vacuum. The cadmium samples were sealed in a purified argon atmosphere to avoid evaporation. The samples were then diffusion-annealed. The temperature of annealing varied between 400° and 630°C and was controlled to ±5°C. On heating to -400°C,the deposits of cadmium, indium, and tin, which were of the order of 0.1 p in thickness, were converted to their respective oxides. The contribution of oxygen present in the lattice of aluminum due to these oxides has been calculated and found to be less than 10 ppm in all cases. Oxide method has already been used by other workers11'12 in diffusion studies without any controversy on the issue. However, in some of these investigations, metallic deposition was also tried. The diffusivities calculated from these measurements were found to agree very well with the diffusivities obtained by using the oxide method. Thus it is assumed that the measured diffusivities represent true diffusion coefficients. Since palladous chloride decomposes at about 500°C, the deposited samples which were to be diffusion-annealed below 500°C were heated in vacuum for a very short time at 500°C to allow the decomposition of palladous chloride to palladium metal. Time taken in decomposition of nitrates to oxides and chloride to metal was negligibly small as compared to the period of the diffusion anneals. The residual activity technique13 was used to study the diffusion profiles where thin layers from the specimen surface were removed by grinding it parallel to a flat surface on a 600-grade carborundum paper. The specimen was washed, dried, and weighed, the differ -ence of the weight being the measure of the thickness of the layer removed. After each such abrasion and weighing, the total residual activity on the surface of the specimens was measured by counting 0.656, 0.94,

Jan 1, 1968

By Joe B. Alford

Founding of the Institute The advance of population and civilization in the U. S. moved through the woodlands of the East, and reached the edge of the great central plains about the middle of the nineteenth century. There the advance paused for almost a generation - ahead were vast reaches of prairie country, uncharted, forbidding, and populated by hostile tribes of the native Indians. The turmoil of the Civil War, and the readjustments following it, further delayed the advance. By about 1870, the Nation was becoming stabilized again, the conflict with the Indians was closing, and the pressure of growth was forcing population to resume its westward movement. In addition to geography, the Nation had another frontier: the development of its immense natural resources. Conditions of the time brought into sharp focus the need for coal, iron, steel, gold, silver, and other minerals. The application of engineering and science was necessary for the production of these minerals and their manufacture into products to meet the needs of a growing nation. The requirements of the time were eloquently expressed in a paper by AIME member Edmund C. Pechin in 1872 : We find, the world over, the most intense activity everywhere displayed in enterprises requiring prodigious quantities of iron. Railways of colossal magnitude are projected. . . . The growing scarcity of timber is compelling the use of iron in buildings; bridges of wonderful size and strength; huge ocean steamships; barges and boats for lake and river traffic; churches; cars, and thousands of minor articles of every shape and size. . . . The time has come when scientific research is to assume its true position - the day of "sheer force and blind stupidity," whose only protection is a high tariff, has gone forever . . . the physicist, the geologist and mineralogist; the chemist, the engineer, are as essential to success as the [blast] furnace itself. . . . There is no merely practical man, no matter how varied may have been his experience, or how long his practice, that will not benefit from the results of scientific investigation. That there is a growing sense of the importance of having thoroughly prepared scientific men in every department of business is evidenced by the institutions [of learning] that are springing up in different quarters, provided with

Jan 1, 1971

By Harry H. Angst, Reuel A. Cochrane

THE successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. ROCK FORMATIONS At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in-the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1941

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ, one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect, which penetrates into the ground and is distorted and, reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in, reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to, reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are-spared the necessity of using a messenger, because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth's gravitational field which furnishes us

Jan 1, 1927