Search Documents

By D. S. Eppelsheimer, D. N. Williams

The cold rolled textures of iodide titanium and of three samples of commercial titanium were examined using the Schulz-Decker Geiger counter technique. The iodide titanium and two of the three samples of commercial titanium showed a (0001) [1010] texture rotated 30' toward the transverse direction about an axis in the rolling direction. The third sample of commercial titanium showed a double texture. THE metals of the hexagonal system tend to deform similarly if the c/a ratios are similar. Thus titanium, zirconium, and beryllium, with c/a ratios of 1.601, 1.590, and 1.570, respectively,l should have similar cold rolled textures. The cold rolled texture of high purity iodide titanium has been described as (0001) [1010] rotated 30" toward the transverse direction about an axis in the rolling direction.' The texture of zirconium has also been reported as (0001) [1010] with a transverse rotation from the ideal position of approximately 30" about an axis in the rolling direction." This texture differs from that reported for titanium however since a continuous spread of (0001) poles toward the transverse direction was reported rather than distinct (0001) maxima 30" from the rolling plane normal. Beryllium has a texture similar to that of zirconium although the angle of transverse rotation of the (0001) poles is much less.' These three metals thus show a common type of cold rolled texture, as yet unexplained, which can be described as (0001) [1010] with various degrees of rotation toward the transverse direction about an axis in the rolling direction. Since titanium showed the greatest degree of rotation from the (0001) [1010] position, the cold rolled texture of titanium was re-examined using a semiquantitative Geiger counter X-ray technique to obtain more accurate experimental data from which a theoretical interpretation of this new type of hex- agonal rolling texture could be developed. The cold rolled textures of iodide titanium and of three samples of commercial titanium were determined. Table 1 gives the analyses of the titanium samples. Experimental Procedure Preparation of Samples: Prior to the final rolling operation each of the samples was given an initial reduction of approximately 50 pct and annealed to remove the gross effects of any previous treatments. Samples were annealed in vacuum, high purity helium, and air to determine whether annealing atmosphere had any effect on the cold rolled textures developed. All samples were annealed 1 hr at 800°C. Grain size determinations were made using the formula, 1.075 in which n is the number of grains counted in an area A (in sq mm) and M is the magnification of the area counted.' This formula gives the diameter between opposite flats assuming hexagonal grains. At least three areas containing more than sixty grains each were counted in each grain size determination. Rockwell B hardness readings were made on the annealed samples. The results of the measurements of

Jan 1, 1954

By G. T. Higgins

PREVIOUS workers1,2 have found evidence of exaggerated grain growth or secondary recrystallization on annealing sponge zirconium at temperatures high in the a, phase field, but no details of the orientation relationship between the secondary grains and "as-recrystallized" matrix were reported. In other hexagonal metals, namely dilute Mg-A13 and Cd-zn4 alloys, secondary recrystallization has been observed in which the secondary grains are related to the primary recrystallized structure by rotations about the c axis. These rotations are thus comparable with the rotations about the (111) axis observed in the secondary recrystallization of fcc metals. In the current work secondary recrystallization has been observed on annealing iodide zirconium at 800°C and the associated changes in crystallographic texture have been examined. The material employed was arc-melted iodide zirconium of the following composition: Impurity O H Fe Hf Pb I Ni C1 A1 ppm by wt 130 5 230 98 23 28 200 39 30 This was received as 0.25-in. plate, and, prior to the annealing studies, was cold-rolled to 0.040 in. Specimens 1 in. sq were chemically polished and annealed for various times at 800°C in a vacuum better than 5x 10-6 Torr. For metallographic examination specimens were first chemically polished and then anodized8 to enhance contrast between the grains when examined under polarized light. Changes in crystallographic orientation associated with the development of secondary grains were followed by (1011) and (0002) pole-figure determinations using a conventional Schulz goniometer in reflection. Filtered Cr Ka radiation was employed and great care was taken to avoid spurious re- sults due to the close proximity of the Bragg angles for the (1011) and (0002) reflections. Figs. 1 and 2 illustrate the change in grain structure on annealing at 800°C. After 24 hr the structure has ceased to be equiaxed due to the development of certain grains in preference to others. It is notable that the secondary grains do not grow to the extent observed in sponge zirconium.1,2 This appears to be due in part to the fact that normal grain growth is inhibited in the less pure sponge zirconium, with the result that the driving force for secondary recrystallization remains high, while at the same time the number of grains able to develop in the presence of the impurities is also smaller. As a consequence, in sponge zirconium those grains that do develop preferentially are able to grow into the fine -grained matrix without impingement, while in iodide zirconium the preferential growth of many grains leads to early impingement. The pole figures determined for specimens annealed for 5 min and 24 hr at 800°C are illustrated respectively in Figs. 3 and 4. These indicate that the dominant feature of the initial recrystallized texture consists of basal planes at an angle of 321/2 deg to the sheet surface, with a (1120) axis lying parallel to the

Jan 1, 1967

By G. W. Form, W. A. Spitzig

The effects of hydrogen and vacuum shtering treatments on the physical and mechanical properties of arc plasma-sprayed tungsten were inuestigated. Temperatures examined ranged from 3000" to 4000°F in vacuum and 2000" to 3000°F in hydrogen for both single and duplex sintering cycles. Densities of 92 pct of theoretical density were obtained when a long-time hydrogen treatment at 2000°Fpreceded sintering in vacuum at 4000°F for 4 hr. This cycle also produced the highest ualues for modulus of rupture and bend angle. The results of this investigation point out the desirability of using a low-temperature long-time hydrogen treatment prior to a high-temperature vacuum sinter for arc plasma-sprayed tungsten. ADVANCES in the development of arc plasma-generating equipment have provided a high-temperature heat source that makes the fabrication of tungsten shapes possible by a metallizing process. Tungsten in the as-sprayed condition is very brittle. It has a density between 80 and 85 pct of theoretical density, a lamellar structure with elongated pores, and a high interstitial impurity content. To improve these properties, sintering treatments can be applied to the as-sprayed material, similar to those used for the densification of compacted tungsten powder. However, in view of the differences in the density and microstructure of as-sprayed tungsten as compared with compacted tungsten, responses to sintering were expected to be different. EXPERIMENTAL PROCEDURES The tungsten powder used in this investigation had a particle size varying from 3 to 13 p with an average diameter of 8p. The impurity level was less than 0.1 pct. The arc plasma spraying was done with an F-40 Thermal Dynamics Corp. plasma jet. Spraying was performed in air and thus required cooling of the substrate by an air blast in order to minimize oxidation. The spraying parameters employed in the fabrication of all specimens are listed below: Power input, kw 12 Arc-gas flow, cfh 95N2 + 5H2 Powder feed rate, g per min 33 Powder carrier gas flow, cfh ION, Spray distance, in. 3 Traverse rate, in. per min 30 Mandrel speed, rpm 100 Nozzle orifice, in. 7/32 These values of the spraying parameters correspond to optimum conditions ascertained in a previous study. Sintering was conducted at 3000°, 3500, and 4000°F in vacuum (< 0.1 Hg), and at 2000 and 3000°F in hydrogen. Duplex sintering treatments investigated are listed in Table I together with the designations that will be used for reference throughout this paper. The samples were fabricated by spraying onto a copper mandrel which was removed prior to sintering. The specimens used for the sintering analyses had the shape of small hollow truncated cones 1 in. high with an inside diameter varying from 0.500 to 0.125 in. and a wall thickness of 1/8 in. Specimens for bend testing were taken from hollow hexagonal prisms 1-1/2 in. high with a 1-in. diam across the flats and a wall thickness of 1/8 in. The bend-test specimens were ground to the dimensions 0.085 by 0.350 by 1-1/2 in. Prior to bend testing 0.0025 in. of stock was removed from each surface by electro-polishing. Density measurements were made by the water-displacement method. In addition, a porosimeter was used to determine the amount of interconnected porosity for representative samples. Strength and ductility were determined from recorded values in transverse bending using a cross head speed of 0.020 in. per min. The load was applied at the midpoint of a 1-in. span. The deflection data reported herein refer only to the plastic portion of the total deflection. RESULTS AND DISCUSSION The as-sprayed samples had a density corresponding to 83 pct (l pct) of the theoretical density of tungsten. Fig. 1 shows a representative as-sprayed tungsten structure.

Jan 1, 1964

By Raymond Edmundson

BARITE probably was first mined in the United States in 1845, when a small deposit was operated in Prince William County, Virginia1. The next state to produce barite was Missouri, and according to Weigel2, mining began about 1860. Virginia was the leading producer during the early period of barite mining, but by 1893, Missouri was producing almost an equal amount3. From this date, Virginia, although not the leading producer, furnished large quantities of crude barite until oper-ations gradually declined about 1907. Since 1910, there has been only one producer in Virginia. It is not known when barite was discovered in each of the Virginia areas (Fig. 1), but it is reliably reported that mining on a commercial scale began in Campbell-Pittsylvania counties about 1874; Smyth County in 1877; and in the Russell-Tazewell area about 1890. Barite is widely distributed in Virginia, occurring in nineteen counties. The localities that contain material of some economic value have been grouped into six areas (Fig. 1), each designated by the county or counties in which the barite is found. As many of the smaller areas show a similarity in geologic occurrence, they will be considered in this paper as two major groups; namely, Appalachian Valley and Piedmont Province. The first group, which includes the barite deposits of Russell, Tazewell, Smyth, Botetourt and Roanoke counties, lies northwest of the Blue Ridge and its foothills and southeast of the Appalachian plateaus. The other group includes deposits from the Blue Ridge on the west to the western margin of the Coastal Plain, in Campbell, Pittsylvania, Bedford, Grayson, and Fauquier counties.

Jan 1, 1936

By F. F. Lines

It is not the intention of the writer to enter into a discussion of the relative merits of the duplex process as compared with the straight scrap and pig iron process, working under the same conditions, but rather to present in a general way several modifications of the former process, and then describe the method adopted by the Maryland Steel Co., as best suited to local conditions, and also to meet the metallurgical problem presented in the removal from the iron of an unusual constituent— chromium. The principal factors to be considered in. deciding whether or not duplexing should be employed are: (1) Chemical constituents of pig iron. (2) Variety and quantity of steel to be produced. (3) Relative cost of pig iron and scrap. (4) Regularity of operation. (5) Capital to be invested. (6) An existing Bessemer plant. Having decided to adopt the duplex process, several combinations may be used, viz.: (1) Acid-lined converter with basic open hearth. (2) Acid-lined converter with electric furnace. (3) Basic-lined converter with basic open hearth. (4) Basic-lined converter with electric furnace. (5) Basic open hearth with electric furnace. The combination of an acid-lined converter with a basic open-hearth furnace is the one most commonly employed, and as it is the one best adapted to the conditions encountered at the plant of the Maryland Steel Co., we will briefly outline the advantages and disadvantages of the different methods of working. There are two general methods of blowing, as follows: (1) The charge is desiliconized and partly decarbonized in the converter. On account of the difficulty in regulating the percentage of car-

Jan 1, 1916

By C. H. Mathewson, H. M. Day

The constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 2760 C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region. Preparation of Alloys The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

By H. M. Day, C. H. Mathewson

The constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 2760 C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region. Preparation of Alloys The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

Jan 1, 1931

By John Henderson

Densities of melts 0f the lime-iron oxide-silica system in contact with solid iron have been measured by the maximum bubble pressure method in the temperature range 1250° to 1440°C and the composition range 0 to 40 mol pct lime, 15 to 100 mol pct iron oxide, and 0 to 55 mol pct silica. Densities range from 4.65 g cm 3 for wustite at 1440°C to 2.75 g cm-&apos; at 1350°C for a melt containing 30 mol pct lime, 20 mol pct iron oxide, and 50 mol pct silica. The results are interpreted in terms of a postulate that the melts can be regarded as a random array of oxygen ions in which regions of local order exist to satisfy the coordination requirements 0.f the cations. An understanding of the nature of metallurgical slags is basic to the development of a sound theoretical description of heavy metallurgical extractive and refining processes. Because these liquids are complex, direct measurements of their properties has not thrown much light on their structure. This has led to the approach of measuring the properties of simpler liquids, and building up their complexity until slag compositions are reached. In this way the density of liquid iron silicates was measured in a previous study1 and the present work represents a further stage in this synthesis. EXPERIMENTAL The technique used in the measurement of density was the maximum bubble pressure method. Details of the apparatus and procedure were similar to those previously reported,&apos; with the exception that a constant voltage transformer was used to supply the power input to the furnace and six silicon carbide resistance elements were used in place of the molybdenum winding. With these modifications melt temperature could be maintained within 1 centigrade degree during the course of a run. The silica used to prepare the melts was washed natural quartz ignited at 1000°C; wustite was prepared by air-melting A.R. grade ferric oxide in an iron crucible and lime was prepared by air ignition, at 1000°C, of weighed quantities of A.R. grade calcium carbonate, previously air-dried at 110°C. The finely ground constituents were intimately mixed in a glass ball mill prior to melting. Temperatures quoted are accurate to * 5°C and the standard deviation of the density values, calculated by the method of least squares, ranged from 0.5 to 1.8 pet. However, replicate determinations of density on different melts of the same nominal composition at the same nominal temperature did not vary by more than 1 pct, Table I, and this figure has been taken as an estimate of the accuracy of the density results. The density of carbon tetra-chloride was also measured as a check on the absolute performance of the experimental method. At 20°C a value of 1.593 * 0.002 g cm"3 was obtained; this compares with the literature value2 of 1.595 g cm"3. Results of experiments designed to measure the dependence of the density of lime-iron oxide-silica melts, in contact with solid iron, on composition and temperature are shown in Table I. Because iron sometimes precipitated in the sample during quenching, the Fe203 chemical analyses were only poorly reproducible and should be taken as a guide rather than as absolute values. Fig. 1 shows the data from various sources for the density of liquid iron silicates and Fig. 2 shows isodensity contours at 1410°C for lime-iron oxide-silica melts, calculated by graphical interpolation of smoothed curves drawn through the experimental results, together with the 1400°C results of Adachi and ogino3 and Pope1 and Esin.4 Fig. 3 shows the isothermal variation with composition of the volume of melt per gram ion of oxygen at 1410°C and Fig. 4 shows regions in which the temperature coefficient of this volume is negative, positive, or negligible (<0.005 cm3 deg-I). DISCUSSION a) Disparity Between Reported Density Results. Consider the system iron oxide-silica, the results for which are summarized in Fig. 1. Although there is some difference in the temperatures at which the various densities apply, this difference is not sufficiently large to account for the observed discrepancies. The reliability of the present results for the low-silica region has been confirmed by measurement of the density of liquid wustite by three different techniques. At 1410°C the density measured by a balanced-column method was 4.55 g cm"3, by a combination balanced-column and gas-densitometer method 4.59 g emd3, and by a pycnometer method 4.53 g cm"3. Schenck, Frohberg, and Hoffermann&apos; have also reported a value of 4.55 g cm"3 for the density of liquid wustite at 1400°C. It must be concluded, therefore, that neither Pope1

Jan 1, 1964

By J. H. Henderson, R. J. Wygal, J. Naar

Experimental work is reported which shows that consolidated rocks and unconsolidated porous media exhibit different imbibition flow behavior. At a given saturation the imbibition nonwetting permeabilities for a rock are smaller than the drainage permeabilities. The contrary happens for unconsolidated aggregates — imbibition nonwetting permeabilities are larger than drainage ones. A similar difference is observed for the wetting phase. Imbibition permeabilities are larger than drainage ones for a consolidated rock but smaller than drainage permeabilities for an unconsolidated medium. The results of these differences are examined for two cases. 1. Flooding Efficiency — Craig&apos;s1 scheme for the computation of production history of a five-spot water flood is shown to agree extremely well with experimental results obtained when using a system packed with glass spheres if imbibition relative permeability curves are used. 2. Alcohol-Slug Displacement — Published theory 2 on oil displacement by alcohol slugs has been questioned despite the apparent agreement between predicted and observed results. The present work suggests that, if imbibition relative permeability curves characteristic of the unconsolidated media used in the early experiments had been available to make the predictions, the inadequacy of the theory would have been immediately evident. The experimental work shows that poorly consolidated formations tend to behave like unconsolidated media. Finally, it is shown that the difference in imbibition behavior is directly related to pore-size distribution and cementation. PART 1 — THE FLOW BEHAVIOR OF UNCONSOLIDATED AGGREGATES Experiments on scaled models of field reservoirs are useful for studying new displacement processes which are incompletely understood. Even when a mathematical description is possible, the solution might be difficult and complex. An answer obtained from a scaled model is extremely valuable in such cases. A great amount of work$-5 therefore, has been devoted to the derivation of scaling laws. Similarity groups have been defined which assume (1) that the relative Permeability curves of the prototype and the model are the same whether the displacement is an imbibition or a drainage process and (2) that there is a linear relationship between the capillary pressure of the model and the prototype. For practical reasons (simplicity in the preparation of models, duration of the experiments, etc.), the porous media of laboratory models are usually unconsolidated packs of sand or glass particles. Hence, unless the capillary and flow characteristics of unconsolidated and consolidated systems are identical, the model data are applicable only to unconsolidated formations. The usefulness of scaled-model studies may then be seriouslyrestricted since most oil-bearing sands are consolidated. Perkins and Collins6 suggested the use of model and prototype curves normalized with respect to both relative permeability and saturation to improve compliance with scaling criteria. Even this technique does not give a satisfactory model-prototype match. This paper reports an observation of two-phase flow in unconsolidated sands which shows that, for most displacements, "scaling" in the strict sense of the word is not even qualitatively feasible with a sand model. It provides, however, a firm foundation for testing a theory by matching it with observed performance of laboratory-size models. EXPERIMENTAL AS a part of a basic study of packed aggregates, the relative permeability of glass-spheres and sand-grain packs was measured with capillary control. The fluids were oil and air&apos; The spheres were packed in plastic cylinders 1-in. in diameter;

By -1ng. B. Stampa

Introduction The author investigates the technology available for mine flow reversibility by reversing the operation of the main fans. Air bypassing, reversed sense of impeller rotation, and blade angle overturning are indentified as the most important means of achieving the flow reversibility. The axial flow fan is studied in some detail and the important variables of fan capacity, pressure, and efficiency are compared. Although some references to rotor velocity vectors are made (Fig. 1) the subject is not presented in detail in order to stay within the paper&apos;s intent. Background Where applicable, the requirements of mine air reversibility are an important part of the overall mining operation and should be given proper attention during mine ventilation design. The need for preventing mine fires in intake shafts is the reason that, for a long time, it has been a requirement in the Eastern European countries to have the feature of flow reversibility built into all main mine ventilators. In West German coal mines, this requirement does not apply since higher priority is given to safety precautions. Some metal and mineral mines in the United States are required to have ventilation currents readily reversible in order to fight underground fires as stipulated by the Title 30, Mineral Resources, and by the mining laws of some states. From an equipment performance standpoint, assuming the validity of other flow technical data, the question of the ventilator flow reversibility is of ten related to the actual scenario of the begining of an emergency. Most of the time, the system operates within half of the design capacity only and assuming that the equivalent mine orifice is stable only a quarter of the design pressure must be produced by the fan in any event. For such an operating point, the effective gradient and energy losses can be disregarded since fire emergencies usually last for only a short period of time. Equipment Comparison Fig. 2 depicts a ventilation arrangement wherein the flow can be reversed through changing the functional position of the dampers (slideplate or blade type). Both axial or radial fans can be applied in this case. For the mine exhaust operation, slide plates (guillotines) I and I11 are opened while plates I1 and IV are closed. The flow thus encounters two reroutings, which due to the reverse ventilation flow cannot be equipped with proper sheet metal deflectors, and therefore large pressure losses result during the air reroute operation. When the intake operation is considered, the dampers I and I11 are closed and the pair I1 and IV is opened. For this arrangement, almost the same flow conditions exist as for the foregoing exhaust mode; however, one additional corner must be applied. Even if a highly efficient ventilator is used in one of the previously described systems, the additional pressure losses resulting from air rerouting plus those encountered between the planes "0" and "00" significantly affect the overall energy requirements. Illustrated in Table 1 are the relative component losses of even flows for evaluation of various detour arrangements. From the aerodynamics standpoint, when these components are being designed, serious consideration must be given to the individual levels of the pressure loss coefficient, 5. Should there be an increase in the sum of the loss coefficients due to the particular component selection such that, for example, the net change is 1.2; the resulting pressure to be produced by the fan can be calculated from:

Jan 1, 1981

By F. Twyman, D. M. Smith

Those chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates may be checked as often as desired. If, possessing these advantages, the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards 19cientific Paper No. 444. The Development of Analysis by Spectrogbaphy Fig. 1 shows, by means of photographs taken with a quartz spectro-graph, what a valuable region of the spectrum is excluded if one has a visual instrument only. Wave length 4023 is about the end of the visible spectrum, the region from 3800 to 1854 being invisible. It is easy to understand then how it is that the vigorous resuscitation of spectrum analysis which has commenced in the last few years has been associated with the use of the quartz spectrograph; notwithstanding that the most useful instrument for the general inorganic chemist to have at his elbow, after the balance, is a good visual spectrometer.(1) 1 The revival of spectrum analysis is to be attributed chiefly to the work of W. N. Hartley with his co-workers, and to A. de Gramont. Hartley,

By B. M. Larsen, W. E. Shenk, T. E. Brower

Shortly after our previous paper on this subject was printed1 we located a source of uncertainty in the results arising from the unexpected fact that hydrogen slowly reduces silica at 1100" C. in presence of iron, even when the iron nowhere touches the silica, although in absence of iron it does not do so. This difficulty has been completely obviated by the use of a small high-frequency furnace, which enables us to heat the specimen for analysis without raising the temperature of the silica vessel to a point at which any appreciable reduction of the silica glass occurs. We now describe this modification of procedure, and present some typical results obtained with it. For any given specimen of steel, the results are entirely definite and reproducible, but their precise significance is still open to some question, as indeed is true of all methods of oxygen determination SO far developed. Further elucidation of this question is to be expected from the cooperative comparison of the several methods now under way under the auspices of the Bureau of Standards at the instance of the Iron and Steel Division of the A.I.M.E. Apparatus The final form of apparatus we have used is identical with that described and illustrated in our previous paper, except for the substitution for the Globar furnace of a small high-frequency furnace actuated by a vacuum tube oscillator2 0f about 1.5 kw. capacity, and for a slight modification of the containing vessel. This transparent silica vessel is illustrated in Fig. 1 of this paper. Its enlarged portion is about 5 cm. in diameter and 13 cm. long. The silica tube for inlet of hydrogen is fused into this bulb and ends beneath the metal "bucket" holding the steel sample. This sample is in the form of fine millings. The "bucket" is suspended by a platinum wire from the cap of Pyrex glass. The high-frequency

Jan 1, 1934

By R. Norman Orava

The strain-mte behavior of. the tensile yielding and flow characteristics of arc-cast polycrystal-line molyhdenum of pidrity > 99.97 pct was investigated in the range 10-6 to 10-1 sec-1 at 243o, 293o, and 373oK for two grain sizes, 0.027 and 9.098 mm. For 0.998 mm, the strain-mte dependence of the lower yield stress can be described by a straight line of the jowl a, = a + 0 log e over the whole range of strain rates examined. However, for 0.027 mm, the data fit several consecutive linear relationships of the above form. The previous association of these different linear regions with different rate -controlling mechanisms is questionable for molyhdenzdm. The senlilog strain-rate dependence of the yield stress is consistent with Hahn&apos;s model for yielding when the stress dependence of the mobile dislocation density, pr, is taken into account. Since p&apos;, from rate -cycling experirnents, is found to be relatively insensitive to stress for single crystaIs, the obserzied log-log dependence of their yield stresses is also in agreement with the model. A correction for the stress dependence of p&apos; changes the activation oolurrze for yielding from a zero to a more realislic inverse function of stress where the Peierls mechanism is believed to be rate-controlling. The gmin-size dependence of the lower yield stress is not a monotonic junction of strain rate. RECENT experimental evidence&apos; has revealed that the strain-rate dependence of the tensile lower yield stress, a,, of commercially pure ni- obium and tantalum tested at room temperature can be described by several consecutive semilog relations of the form: sv =a + ß log € [1] where i is the applied strain rate and a and 0 are constant Over only relatively small ranges of strain rate. Three linear regions were found for niobium and four for tantalum. Each linear region was interpreted as being associated with a different rate-controlling mechanism on the basis of the current

Jan 1, 1964

By J. L. Sepulveda, R. F. Yap, R. Jauregui

INTRODUCTION The Third Theory of Comminution, oftentimes called the Bond Theory, was first published by Fred C. Bond in 1952. Since then, it has been widely used in the milling industry to size crushing and grinding equipment as well as to predict and evaluate their performance. Although two other comminution theories were advanced almost a century earlier, one by Rittinger, 1867, and the other by Kick, 1885, their use was limited because they did not agree with actual commercial comminution systems (Bond, 1961). According to Bond&apos;s Third Theory, the work input is proportional to the new crack tip length produced in particle breakage, and equals the work represented by the product minus that represented by the feed. For particles of similar shape, the crack tip length is equivalent to the square root of one-half the surface area, and the new crack length is proportional to [(1/vT - vF)]; where P and F are particles diameter of product and feed, respectively. For practical calculations, the particle diameter can be expressed in terms of the 80% passing sizes, P and F, respectively. Therefore, the work input is given by, [10 _ 10&apos;, W = Wi [7P_7F(1)] Where W = the energy input to the mill, (kwh/t) Wi = Work Index, (kwh/t) P = square sieve opening which 80% of the product passes, (microns) F = square sieve opening which 80% of the feed passes, (microns) Equation (1) is the mathematical statement of the Third Theory, or the Bond equation. Numerically, the work index is the energy required in kwh/t to reduce a given material from theoretically infinite feed size to 80% passing 100 microns. The work index of a particular material is determined in the laboratory by conducting the standard Bond grindability test. Bond developed separate tests for the rod mill and the ball mill. The simplified test method described in this paper, which is used at Anaconda Research Center to approximate the work index, is an alternative procedure to the ball mill

Jan 1, 1982

By W. C. Clarke

An empirical study of the nature of the embrittle-ment which occurs in martensitic and semiaustenitic precipitation hardening stainless steels upon exposure at temperatures of from about 550" to 875°F has been undertaken. This work was aimed at determining cazusation and means of controlling this phenomenon. A commercial copper bearing precipitation hardening alloy was used as a basic material for study. The effect of heat treatment variables was studied as was the effect of variations in analysis. It is concluded from the evidence that martensitic and semiaustenitic precipitation hardening stainless steels are subject to 885°F ernbrittlement similar to that observed in the straight chromium stainless steels. A characteristic of precipitation hardening stainless steels which has limited their use in certain applications is that they embrittle when held at temperatures in the range of from about 550" to 900°F. This is true to a more or less degree in all currently available alloys, either the basically martensitic type or the semiaustenitic type. The rate of embrittlement varies markedly with exposure temperature, being low at 550" to 600°F and in-creasing as the temperature increases. In spite of this embrittlement, these alloys with their unique combination of high mechanical strength, reasonable toughness, and good corrosion resistance are used in many hundreds of applications. Nevertheless, there are potential applications where the embrittle-ment described is a limiting factor. The purpose of this investigation was to study the embrittlement of these alloys and to find a way to control or eliminate it. GUIDELINES USED IN PRESENT WORK The work reported in this paper is based on a study of 17-4 PH*, a very widely used alloy. It has been used *Trademark of Armco Steel Corp., licensor. in pressurized water and boiling water atomic reactors operating at about 550°F for a number of years. As the life of such equipment is extended or operating temperatures are raised, the possibility of embrit-tlement becomes of increasing concern to materials engineers. Much investigation work was done with respect to the use of 17-4 PH at 550°F. K. C. Antony&apos; states "Such estimation" (of an activation energy for the diffusion of chromium in iron) "would indicate W. C. CLARKE, Jr. is Senior Research Engineer, Advanced Materials Division, Armco Steel Corp., Baltimore. Md. This manuscript is based on a talk presented at the symposium on New Developments in Stainless Steel, sponsored by the IMD Corrosion Resistant Metals Committee, Detroit, Mich., October 14-15, 1968. significant secondary aging is improbable at temperatures less than 700°F within normal component service life". This statement is modified however by the recognition of the accelerating tendencies of applied stress and internal stress as well as the possible effect of irradiation. In this investigation of 17-4 PH, the H 1100 (1900°F-1 hr oil quench or air cool + 1100°F-4 hr-air cool) condition was used, partly because this condition is normally used in atomic reactors. As shown later, the precipitation hardening temperature has no real bearing on the rate of embrittlement. An exposure temperature of 800°F was selected since embrittlement at 800°F is rapid, permitting development of relative data in time periods of 400 to 500 hr. For those not familiar, a nominal present day analysis of 17-4 PH is: C Mn P S SiCrNiCuCbN 0.04 0.30 0.015 0.015 0.60 16.00 4.30 3.25 0.23 0.030 TYPICAL BEHAVIOR OF 17-4 PH Figs. 1 and 2 show the behavior of a commercial heat of 17-4 PH under the conditions defined. Characteristically, 800°F exposure causes a rapid drop in Charpy V-notch impact strength. Tensile and yield strengths gradually increase and a gradual loss of elongation and reduction of area occur, accompanied by an increase in hardness. Notched tensile strength increases to 125 hr exposure and then sharply decreases after exposure for 500 hr. The notched vs un-notched tensile ratio remains virtually constant to exposure for 125 hr (1.67 to 1.56) but drops to 1.15 after 500 hr. Tensile ductility is not alarmingly affected even after much longer exposure times than these. For example, samples aged at 1100°F for 1 hr exposed at 800°F for 4000 hr showed a drop in elonga-tion of from 13 to 11 pct and in reduction of area of from 58 to 37 pct. Notched impact is the property SmIgth KSI 3JJ[/__________^UTS-Nrteh 260 ;/- 240 —^ 200 UTS-Smooth________._, o ioo mo Sob" m Too Hours Exposure Fig. 1—Effect of exposure at 800°F for various times on notched tensile strength and smooth tensile and 0.2 pct yield strength of 17-4 PH in the H 1100 condition.

Jan 1, 1970

By D. V. Edmonds, C. J. Beevers

Tensile tests were carried out on a! titanium containing 850, 1250, and 2700 ppm 0, and up to -500 ppm H. The tests were performed at -196", -78", 20°, 150°, and 300°C at a strain rate of -1.0 x 10??3 sec-1. Increasing oxygen content, increasing grain size, and decreasing test temperature resulted in enhanced embrittlement of the a titanium by the hydrogen additions. Metallographic observations showed that this can be correlated with the influence of these parameters on the introduction of cracks into the a! titanium by fracture of titanium hydride precipitates. CRAIGHEAD et al.1 reported that the hydrogen content normally found in commercial-purity a! titanium (60 to 100 ppm) was sufficient to cause a substantial lowering of the impact strength, and they attributed this embrittling effect of hydrogen to the precipitation of titanium hydride. Lenning et al.&apos; found that in commercial-purity a titanium there is an almost complete loss of impact strength at about 200 pprn H, which is approximately half the value needed to eliminate the impact strength of high-purity a titanium. They also showed that the presence of 3000 ppm hydrogen reduces the room-temperature tensile ductility of commercial-purity material to a value of the order of 10 pct; the corresponding hydrogen concentration for high-purity titanium is over 9000 ppm. It thus appears that the detrimental effect of hydrogen on the mechanical properties of commercial-purity titanium becomes evident at much lower hydrogen contents than for high-purity titanium. The main difference between the two types of a titanium might be expected to be the higher level of interstitial impurity in the commercial-purity grade. Jaffee et a1.3 studied the influence of temperature and strain rate on the hydrogen embrittlement of high-purity and commercial-purity ! titanium. In general, the behavior was the same for both materials; embrittlement was enhanced by decreasing temperature and increasing strain rate. Recent results from tests on commercial-purity a titanium containing 850 ppm O and varying amounts of hydrogen up to -500 ppm showed that the degree of embrittlement by hydrogen is intimately related to the fracture characteristics of titanium hydride precipitates.4 The present paper considers the interrelationship between the mechanical properties and micro-structural features of commercial-purity a! titanium containing 850, 1250, and 2700 ppm 0 and varying amounts of hydrogen up to -500 ppm. 1. EXPERIMENTAL PROCEDURE Three types of commercial-purity titanium supplied by IMI* were used in the investigation, and for the *Address: Witton, Birmingham 6, United Kingdom. purpose of this paper are designated Ti 115, Ti 130, and Ti 160. The principal impurity elements are given in Table I. The material was received in the form of 12.7 mm diam bars having a fully recrystallized structure. Tensile specimens with a round cross-section of 4.5 mm diam and a gage length of 15.2 mm were machined from the bars. In order to develop the same grain size (mean linear intercept of grain boundaries) in each of the three types the specimens were annealed under a dynamic vacuum of <10?5 mm Hg, Table 11. Specimen hydriding was carried out in a modified Sieverts apparatus;&apos; hydrogen was taken into solution at 450°C and after holding the specimens at this temperature for 24 hr they were furnace-cooled to room temperature at an average rate of -100 C deg per hr. By this method nominal hydrogen contents of 0, 50, 100, 250, and 500 ppm were introduced into specimens of Ti 115, Ti 130, and Ti 160 (100 ppm (wt) -0.5 at. pct). The actual hydrogen contents were calculated from the weight differences obtained by weighing the specimens before and after the hydriding treatment. Tensile tests were carried out at temperatures of -196", -78", 20°, 150°, and 300°C on a 10,000 kg In-stron machine at a nominal strain rate of -1.0 x 10-3 sec-1. Fractured specimens were sectioned in planes parallel to the tensile axis, mechanically polished to 0.25 µm grade of diamond paste, and then attack polished using a solution containing by volume 99 parts H2O, 1 part HF, and 1 part HNO3. Although the latter treatment unavoidably opened out cracks and voids visible after mechanical polishing, it did reveal the grain structure, titanium hydride morphology, and deformation twinning structure.

Jan 1, 1970

By L. Delisle

This work represents the first step of an attempt to test the applicability of the electron microscope to the study of subgrain structures in copper. Observations on annealed and deformed single crystals and polycrystalline samples of copper are described. IN the course of study of the structure of fine tungsten wires and tungsten rods with the electron microscope, well defined subgrain structures were observed. The size, size distribution, and orientation uniformity of the etch figures varied widely in different samples. Figs. 1 and 2, electron micrographs of a tungsten wire and of a tungsten rod, respectively, are illustrations of the difference in size and size distribution of the etch figures in different samples of the same metal. The observed differences, as pointed out in a previous paper,&apos; appeared to be related to the heat and mechanical treatments of the samples. They were also consistent with the results reported in the literature on the mosaic structure of metals.&apos; For that reason a program of research was initiated in an effort to obtain more systematic evidence of the possible relation of heat and mechanical treatments to the subgrain structure of metals as observed in the electron microscope. The purpose of this paper is to present observations made on the effect of cold work on the subgrain structure of copper. Procedure Starting Materials: Copper was the metal studied because it can be obtained in a high degree of purity, much information is available in the literature on its properties and its response to cold work and heat treatment, it shows no allotropic change, and it is sufficiently hard to be handled without great difficulty. Two groups of specimens were used: 1—single crystals cast from spectroscopically pure copper and 2—polycrystalline samples of oxygen-free high conductivity copper. Single crystals were studied because it was hoped that the elimination of a number of variables, such as grain boundaries, orientation differences, degree of purity, would simplify the problem and perhaps permit a better understanding of the phenomena that would be observed. The polycrystalline samples were designed to give a general picture of the changes considered. The single crystals were made of copper which analyzed spectroscopically to better than 99.999 pct Cu. They were cast in vacuum, by the Bridgman method, in crucibles made of graphite with a maximum ash content of 0.06 pct. The mold design is shown in Fig. 3. It permitted casting crystals of the size and shape required for the experiments, so that the danger of introducing cold work in the original samples by cutting or other machining would be eliminated. The polycrystalline samples were pieces, 3/4 in. long, cut from a rod of oxygen-free high conductivity copper, % in. in diameter. A flat surface, 1/4 in. wide, was milled along the rods, polished, and etched. The samples were then annealed in vacuum at 850°C for 1 hr. Polishing and Etching: Work previously done on tungsten,&apos; polished mechanically and etched chemically," had shown that: 1—the general appearance of the etch figures of a given sample was not altered by repeated polishings and etchings under similar conditions; 2—variations in the time of etching and the concentration of the etchant changed the definition of the etch figures, but did not alter their general size nor orientation distribution within the limits of observation. Further work confirmed the reproducibility of the subgrain structures observed in, 1—single crystals and polycrystalline samples of copper when polishing and etching were repeated under similar conditions, and 2—specimens of tungsten and polycrystalline copper when electrolytic polishing and etching were substituted for mechanical polishing and chemical etching, respectively. On the strength of these observations, it was felt that, if conditions of polishing and etching were kept constant, changes observed in the subgrain structure of a sample upon deformation and annealing would be attributable to such treatments. For that reason the conditions of polishing and etching were kept as constant as possible. The single crystals were polished electrolytically in a bath of orthophosphoric acid in water, in the ratio of 1000 g of acid of density 1.75 g per cc to 1000 cc of solution, under a potential drop of 1.6 to 1.8 V. Electrolytic polishing was selected to prevent the formation of distorted metal in polishing. The same samples were etched by immersion in a 10 pct aque-

Jan 1, 1954

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By Robert Ammon

The purpose of this paper is to present a brief sketch of the development of this hindered-settling classifier, but primarily to show the actual results obtained in practice with the classifier working on the Butte copper ores at the Boston & Montana Concentrator at Great Falls and the Washoe Concentrator at Anaconda. The writer has endeavored to be as brief as possible, giving only the essential figures showing the efficiency of the classifier and leaving considerable interesting information to be derived by the reader from the statistics given. The paper deals with the practical work of the classifier under the following heads: 1. Desliming 4.0-mm. primary feed, overflow from 0.07 to 0.0 mm. 2. Desliming 1.25-mm. secondary feed, overflow from 0.07 to 0.0 mm. 3. Desliming Huntington Mill discharge, overflow from 0.07 to 0.0 mm. 4. Classifying 2.5-mm. deslimed secondary feed, overflow from 1.00 to 0.07 mm. 5. Classifying 2.5-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 6. Classifying 4.0-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 7. Classifying middling-tailing product from roughing tables, overflow coarse tailing. 8. Classifying 2.5mm. trommel undersize, not deslimed, overflow from 0.75 to 0.0 mm. 9. Remarks on the inner feed cone. In the following pages all overflows are given in quartz dimensions; i. e., by a 0.75-mm. overflow is meant an overflow whose maximum particle is a 0.75-mm. quartz grain. By the term "slime" is meant all material which will pass through a 200-mesh screen whose average opening is 0.07 mm. The development of the classifier was commenced in the fall of 1910,

Jan 1, 1914