Search Documents

By Harry Morgan

ONE of the direct results of the increasing number of oil wells drilled to greater depths has been the development of new types of bits. These bits should resist the abrasive action of drilling and give the greatest footage before bit changes become necessary on account of dulled cutting edges. The loss of drilling time caused by changing bits becomes more important as the well becomes deeper, because the whole drill pipe must be unscrewed to make; each change. Under ordinary conditions the change takes: 2 1/2 hr. for round trip at 4000 ft., 3 hr. for round trip at 5000 ft., 4 hr. for round trip at 6000 ft., 5 hr. for round trip at 7000 ft. In other words, the time to change a stand of drill pipe (90 ft.) varies from 1 2/3 min. at 4000 ft. to 23 min. at 8000 ft. In general, the formation in the deeper zones is harder and dulls bits more quickly than the formations nearer the surface, therefore even a small increase of hole drilled per bit will decrease costs and increase speed of drilling.

Jan 1, 1929

By J. B. Clark, F. N. Rhines

THE A1-Mg phase diagram in the composition range from 30 to 60 pct Mg remains uncertain. Four intermetallic compounds are reported in this composition range. All of the published diagrams are in agreement as to the existence of intermediate phases near 37 and 52 pct Mg (Mgl,A1,). Confusion exists, however, as to the number and identity of the intermetallic phases present in the intervening composition range from 37 to 52 pct Mg. Mikheeva and Kurnakovl denote the existence of a phase e near 42 pct Mg. Kawakami," Reiderer? and Laves report a phase near 48 pct Mg. Eickhoff and Vosskuhler, from a critical survey of the literature, composed the diagram shown in Fig. 1, with the exception of the eutectoid horizontal of the e-phase shown at 210°C. RaynorV n a similar survey discounts the existence of the phase proposed by Ka-wakami et al.' at 48 pct Mg and reports a composite diagram similar to that of Eickhoff and Vosskuhler." This uncertainty as to the number of intermetallic phases in the A1-Mg system may be eliminated by annealing a diffusion couple of pure aluminum and

Jan 1, 1958

By H. R. Deeth

NEPHELINE syenite is a sodium, potassium, aluminum silicate rock occurring in many countries. Large deposits have been investigated in Russia, India, and Norway and in the U. S., where it is known to occur in Arkansas, New Jersey, and Wisconsin. There are extensive areas containing nepheline syenite in south-central Ontario, a region surveyed in 1905 by Adams and Barlow. By 1925 considerable interest had developed in searching for aluminous raw materials that could be used by the glass industry. This finally focused attention on the nepheline syenite described by Adams and Barlow in 1910.1

Jan 11, 1957

By F. C. Schora, H. P. Meissner

COUNTERCURRENT staged processes involving chemical reactions between solid and gas streams are becoming more common. Such operations are generally carried out in a series of fluidized beds with each bed acting as a stage. Fig. 1 is a schematic illustration of a series of stages located in a single column, with a solid stream moving down through this column from stage to stage counter to a rising gas stream. The reduction of iron oxides with hydrogen and carbon monoxide is one of the reactions which can be advantageously carried out in such a countercurrent system. Calculation of the performance of a countercur-

Jan 1, 1961

By Gerald C. Mathis

FERGUS County, Mont., shown in Fig. 1, is known for its once famous gold mines near the old towns of Gilt Edge, Maiden, and Kendall. But at Heath, a small farming community near the foot-hills of the Snowy Mountains, thousands of tons of gypsum have been mined since 1916. The value of the gold taken from the mines of Fergus County runs into millions of dollars; the value of the products made from the gypsum of the Heath mine is also in the millions. The gypsum mine will continue to produce for many years, while the gold mines are closed today.

Jan 2, 1953

By Duk-Won Park, Syd S. Peng

INTRODUCTION More than five years have elapsed since the first shortwall panel was installed in a US mine in 1972. By the latest count, 11 mines have tried the shortwall method on 34 panels. Potentially, the shortwall method (see Figure 1) offers the combined advantages of longwall and continuous mlning. But just like any other mining method, shortwall is not a panacea. It is only applicable under a set of stringent conditions. Coal operators at eight of the eleven mines are satisfied with shortwall mining, though there are only five mines presently producing coal from shortwall panels.

Jan 1, 1981

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 12, 1979

As REVISED IN CONFERENCE FEB. 17, 1931 REPORT OF SUBCOMMITTEE ON MINE VENTILATION CODE OF A, I. M. E. COMMITTEE ON VENTILATION ALFRED W. HESSE, Chairman THOMAS G. FEAR GEORGE S. RICE E. A. HOLBROOK WILLIAM A. ROWE HOWARD ECKFELDT R. V. NORRIS CADWALLADER EVANS, JR. H..1. SMITH, Secretary REALIZING, from the safety and health standpoint, the need of furnishing air of good quality to workers underground and of diluting and carrying away dangerous and noxious gases, the following code is offered to unify regulatory measures in coal mine ventilation, so far as is practicable, in the United States of America.

Jan 1, 1931

By Donald Towse

Geothermal energy can substitute for and compete with other fuels, but until now it has been used only in special situations where it costs much less than alternate fuels. Geothermal heat is expected to be developed where it can: (1) compete with alternate fuels, (2) replace scarce fuels, (3) be more environmentally acceptable, or (4) is especially adapted to local needs. Economic problems in development include the often high capital costs of wells and gathering systems and the long lead-times required for electric generating plants. The large investment and long payout times for large industrial uses adversely affect the economics.

Jan 1, 1977

By Arno C. Fieldner

PROBABLY no large industry in the United States is in greater need of technologic research leading to economic improvement than the coal industry. It has suffered severely from increasing substitution of petroleum and natural gas for coal and its products in the fuel markets. Part of this substitution is due to the greater convenience and suitability of liquid and gaseous fuels for special purposes, and part of it has been due to the extensive research programs conducted or sponsored by the petroleum and allied industries in the past 2 decades. A recent estimate1 places these expenditures at $100,000,000 a year.

Jan 7, 1951

By Robert F. Mehl

THE gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transforma-tion rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data, on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2 since then several important papers have appeared. Our present, knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-cen-tered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-Centered alpha lattices in tampered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: { 111 }Y//{110}a [110]Y//[111]a

Jan 1, 1937

By Dilip K. Paul, Charles H. Jacoby

The economic importance of salt domes has been recognized throughout the world, primarily because of oil and gas accumulations on their flanks, and to a lesser degree, for the value of their salt and potash. Recently they have become of value as hosts for cavities used to store hydrocarbons. In the near future we believe that their main value will be a source of geothermal energy. Although tremendous effort has been expended on the understanding of the geology and physical characteristics of the strata intruded by salt domes, relatively little energy has been exerted in the comprehension of the salt dome itself. Salt domes have long been recognized as a geological heat anomaly. With respect to other sedimentary rocks, salt is a good conductor of heat. Expressing values in 10-3cgs units, sedimentary rocks vary from 1.0 to 8.0; metamorphic rocks from 5.2 to 8.4 and igneous rocks from 3.1 to 9.8. Rock salt in its pure form has a thermal conductivity of 17. Thus a salt dome can be expected to act as a conduit bringing heat vertically from deep within the earth's crust.

Jan 5, 1974

By G. T. Hahn

On the basis of the recommendation of Lovell, Vogel, and Wernick,&apos; Fry&apos;s reagent*2 was recently c) if decoration of the dislocations by carbon or nitrogen atoms is a factor in the etch pitting. Experiments were performed with samples of a commercial 1020 steel, a vacuum-melted iron (C - 10 to 15 ppm, 0 - 20 to 50 ppm, N < 2 ppm), both annealed 4 hr at 1100°C, and a zone-refined iron (C - 3 to 5 ppm, 0 - 10 ppm, N < 1 ppm ) in the as-cast condition. Saomple surfaces were prepared by grinding to 600A grit and electropolishing. Initially, effects of etching the steel with modifications of the basic Fry composition were examined. It was found that increasing the alcohol or HC1 concentratior~ retarded dislocation pitting; reducing the acid content promoted secondary pitting. Cooling the reagent and the sample did not improve the quality of the etch pits. Best results were obtained with freshly prepared reagent modified by increasing the CuC12 content to 15 g. This composition was used in subsequent experiments. Annealed samples were etched 10 to 15 sec; cold-worked samples —2 to 5 sec.

Jan 1, 1962

By Kenneth N. McLeod, Donald W. McGlashan

In the use of free bubbles with precise temperature control and continuous pH measurement, the contact angle apparatus differs from all previous equipment. Experimental procedures differ sharply from the captive bubble method of introducing the gaseous phase in the three-phase system. When freed from the tube and captured by a solid surface, a bubble more closely conforms to the spherical ideal set up by the usual mathematical analysis of surface free energy or surface tensional relationships of the forces involved. The assembled equipment, Fig. 1, departs from the usual contact angle apparatus in providing: 1) water circulation for fixing temperature, 2) instruments to measure and record pH during testing, and 3) a system for producing and using free bubbles. The apparatus allows testing over a broad range of closely controlled conditions, and the use of free bubbles gives contact angles independent of operator manipulation, which was unavoidable in the older captive bubble method. A bubble released below the specimen rises through the liquid and contacts the mineral. If the mineral is gas-avid the bubble adheres, developing a finite contact angle.

Mar 1, 1956

By A. C. Dorenfeld

CHANGES in circuits are often made in milling operations. At the same time that these changes are being evaluated the ores are changing. Even from the same mine, the ore is usually variable as to amount and type of mineral content, degree of association of valuable and gangue minerals, amount and types of soluble salts, hardness, etc. The question then arises whether any small differences in results, after changes have been made in the various circuits, are really due to these changes or whether the variability of the ore can account for those differences. Statistical evaluation provides one method of answering the question that arises so often in beneficiation studies: Did changed results come about because of changed process, or did ore variation cause the change? In this case, data were available for statistical analysis from an operating period of 42 months, representing treatment of approximately 1 million tons of ore. During this period there had been two flowsheet changes: 1) regrind of the zinc circuit middlings was introduced, and 2) alcohol- pine oil frother mixture was substituted for cresylic acid-pine oil frother mixture. Findings are in Table I.

Jan 10, 1954

By R. E. Maringer, A. Schwope

IT has been recognized that oxygen in minute quantities is extremely detrimental to the room-temperature ductility of molybdenum. Early fracto-graphic studies&apos; of the cast metal indicated that oxides are formed preferentially at the grain boundaries. Additional verification of this preferential segregation has been obtained from internal friction studies on poly crystalline molybdenum (average grain diameter varied from 0.039 to 0.065 mm) and from observations of the effect of oxygen on specimens of extremely large grain size. Specimens A, B, and C, of 0.040 in. diameter commercial molybdenum wire (Lot FW 13-40) were heat treated in the vacuum furnace described by Few and Manning according to the specifications given in Table I. Internal friction studies of these specimens were carried out using a low frequency (approximately 1 cycle per second) torsional pendulum completely enclosed in a vacuum tank. As the pressure of oxygen in the heat treating atmosphere changed, the portion of the internal friction vs temperature curves ascribed to grain boundary relaxation changed correspondingly, Fig. 1. The decrease in the damping capacity at high temperatures as the pressure of oxygen in the heat treating atmos-

Jan 1, 1955

By Ossi E. Palasvirta

The authors are to be congratulated for their interesting article, which thoroughly illustrates the variables inherent in filtration of taconite concentrate. The work and the conclusions based thereon largely parallel the test work done by the writer at the Pilotac plant* and the experience gained with a commercial size agitating disk filter in the same plant. At Pilotac, however, a thorough study was also made of the effect of depolarizing (demagnetizing) the filter feed, and it is the purpose of this discussion to comment on the merits of depolarization of the magnetite concentrate prior to filtering. The work at Pilotac was done in three phases: 1) preliminary laboratory testing with a circular filter leaf of 0.047 sq ft, followed by 2) plant testing using a 4-ft diam, single-disk agitating filter that was purchased on the basis of the pilot tests on the 4-ft model. In the laboratory tests depolarization was achieved by slowly withdrawin4 batches of thickened concentrate from a coil producing an alternating field of about 300 oersteds. In plant tests the standard Pilotac procedure1 was employed, wherein the pulp falls freely through the depolarizing coil.

Jan 5, 1958

By Raymond Dugdale, Fathi Habashi

There has been a recent interest in studying the action of anhydrous sulfur trioxide on ores to convert the metal values into a water-soluble form as a substitute for leaching by sulfuric acid. For example, Svenke1 converted the small amounts of uranium in slate ash into a water-soluble form by treating the material with SO, at about 600°C. Chao and Sun found that a variety of aluminum-bearing minerals could be sulfatized by SO, in the temperature range 400° to 600°C usually in the presence of a catalyst such as sodium sulfate. Kruse3 patented a process for beryllium recovery from the low grade ore in Utah by first reacting it with SO, at 560° to 750°C then leaching the product with water. In the present report, the action of SO, was examined in the temperature region 100°-300°C which was not investigated by those workers. Experimental Tests were conducted on a beryllium ore sample from Utah, the analysis of which is given in Table 1. It corresponds closely to a saponite ore type as given by Crocker et al. It was in powder form 45% passing a 400

Jan 1, 1973

By F. W. Aul, R. C. Glenn

EXTRACTION techniques are of particular importance in determining size, shape an: crystal structure of particles smaller than l000Å in steels and other alloys. However, artifacts that can arise during the preparation of extraction replicas may lead to erroneous conclusions. The purpose of this note is to illustrate some of these artifacts and the misinformation that can result from their presence. An alloy of iron with 0.8 pct Cu was investigated in the following conditions: 1) Solution treated 3 days at 925°C in dry hydrogen and quenched in water. Aged in steps to precipitate copper, as follows: heated to 700°C, held 1 day; then furnace cooled to 50O°C, held 3 days; then furnace cooled to room temperature. 2) Solution treated 3 days at 925OC in dry hydrogen and furnace cooled to room temperature. 3) Solution treated 3 days at 925OC or 17 hr at 1100°C in dry hydrogen to dissolve all copper, then quenched in water. A normal parlodion dry-extraction technique was employed after etching the specimens with super picralP or with 2 pct nital. A wet-extraction method

Jan 1, 1962

By G. S. Hume

As predicted a year ago, owing to the discovery in 1936 of crude oil on the west flank of the south end of Tuner Valley in the eastern foothills of Alberta, 50 miles southwest of Calgary, and the drilling activity that resulted, the production of crude oil in Canada during 1937 showed a very substantial increase over the previous year. The production from other parts of Canada is relatively small and shows slight variations only from year to year. The production of crude oil in Canada and the production in Alberta, the main producing Province, is shown in Tables 1 and 2.

Jan 1, 1938