Search Documents

By E. R. Borcherdt

IT is notable that the first large-scale mine operation equipped entirely with detachable bits was the Badger State mine of the Anaconda Copper Mining Co. in Butte, Montana, just 30 years ago. This mine in 1922 was producing approximately 1200 tons of ore per day. Much of the data presented in C. L. Berrien's article1 describing the development and installation of the Hawkesworth detachable drill bit were obtained from these operations. As in any pioneering effort, no precedent existed and many difficult problems required solution, so that the changeover to detachable bits at all Butte hill mines was not completed for 6 years. There was widespread disbelief as to the probable efficiency of the new installation.

Jan 2, 1953

Dubbed "Freeport's Mission Impossible" by the trade press, the company's Ertsberg mine in West Irian nevertheless shipped its first concentrates in December 1972, ahead of schedule. This is a new and great chapter in the history of Freeport Minerals Co. and its contractors. Exploration and construction were only possible by moving equipment and supplies by helicopters. This work was carried out by Petroleum Helicopters, Inc., of Lafayette, La. At the peak of operations six machines were in service manned by 11 pilots and supported by 10 mechanics. During the month of August, with work in full swing 1,604 tons were moved, including 3 DC-6 tractors requiring 18 trips each; flying hours for the month were 636.

Jan 1, 1973

By William E. Ford, Edward Salisbury Dana

The NATIVE ELEMENTS are divided into the two distinct sections of the Metals and the Non-metals, and these are connected by the transition class of the Semi-metals. The distinction between them as regards physical characters and chemical relations has already been given (Art. 453). The only non-metals present among minerals are carbon, sulphur, and selenium; the last, in one of its allotropic forms, is closely related to the semi-metal tellurium. The native semi-metals form a distinct group by themselves, since all crystallize in the rhombohedra1 class of the hexagonal system with a fundamental angle differing only a few degrees from 90°, as shown in the following list :

Jan 1, 1922

By E. K. Olson

Eagle Mountain mine of Kaiser Steel Corp. began production in 1947 when the direct shipping ore contained 51-56% Fe. The high grade, wide ore face and low stripping ratio ores were rapidly depleted and Eagle Mountain required processing plants for upgrading and more efficient mining equipment. During 1970-71 total annual pit tonnage averaged 56 million tons of material ranking the Eagle Mountain Mine as the fourth largest in the country. Ore production averaged 12.5 million tons requiring a stripping ratio of 3.5: 1. During this period mining activities were scheduled for a three-shift, seven-day operation. The present mining rate is about 30 million tpy on a two-shift, five-day schedule.

Jan 12, 1972

By Colin Fink

TANTALUM and columbium occur together in tantalite and columbite ores, which may be considered as ferrotantalate (FeTa206), with part of the iron and tantalum replaced by manganese and columbium respectively, the general formula, therefore, becoming (Fe, Mn)O.(Ta, Cb)205. The ratio of tantalum to columbium is not fixed; the amount of tantalum may vary from one-third to three times that of columbium. Minerals having a high content of tantalum are called tantalite, while those possessing larger amounts of columbium are classified as columbite ores. These minerals are found in pegmatites and often occur in veins associated with cassiterite and wolframite, and may contain small amounts of tin, tungsten, titanium and silica.1

Jan 1, 1931

By R. A. Wyman

KYANITE schists in the Sudbury area have been generally described by Haw,1 who has also given particular information on preliminary treatment of three large samples from Dryden township, Ontario.2 Kyanite, garnet, biotite, quartz, and feldspar comprise the main ingredients of this ore. Kyanite is the valuable mineral. About 5 ½ tons of -35 +200 mesh product, made by dry rod milling, screening, and separation on the Exolon magnetic separator, were available for treatment by flotation. Magnetic separation had effectively reduced garnet and biotite so that flotation feed consisted essentially of kyanite, quartz, and feldspar, the kyanite content averaging 32 pct and representing about 86 pct of the kyanite in the original ore.

Jan 1, 1958

By J. R. Billingsley

The Sunro mine, operated by Cowichan Copper Co. Ltd., under lease from Sunro Mines Ltd., a Cominco subsidiary, is located on the south end of Vancouver Island. Exploration and limited development before 1960 established the existence of twelve mineralized zones. The "B" and "C" orebodies of the River zone contained an estimated 937,000 tons of 1.80r/, copper plus approximately 35 cents per ton of precious metals. On reviewing the indicated tonnage and the exploration possibilities in the River zone and the other eleven zones it was decided to construct a 1500-tpd mill. In August 1961, excavating of chambers for a crushing plant and concentrator located underground near the River zone began.

Jan 12, 1963

By H. M. Callaway

There are key words common to Government and the minerals industry, the use of which immediately spark interest, argument and confusion. Among these is productivity, a term ranking for widespread misunderstanding with mineral self-sufficiency and mineral conservation. Each interpretation of these words tends to emphasize a single aspect and either minimize or ignore the complex dynamic system of things that influence the Nations mineral productiveness. This paper1, abstracted from a monograph on lead now being prepared for publication by the Bureau of Mines, not only sheds light on the trend of productivity in the lead-zinc mining industry but it presents the basis for forming a common general notion of what the term productivity implies.

Jan 11, 1961

Bellows Connector Fabricated of chemically inert Teflon, the new bellows type connector has many pipe line applications where vibration, expansion and electrolysis exist in the handling of corrosive liquids or gases and solvents. The new connector is electrically non-conductive, flexible even at 94°F and as strong as 480°F as at 70°F, according to the manufacturer. This bellows connector serves as a [ ] vibration dampener as well as an expansion joint and connects misaligned couplings and insulates flanges electrically. End flanges of the joint are French-type envelope gaskets made integral with the joint for easy assembly between companion flanges and a tight, leak-proof seal on installation. Circle No. 1

Jan 1, 1952

By Reed S. C. Rogers, Robin P. Gardner, Kuruvilla Verghese

The development and use of short-lived radioactive tracer methods for the onstream determination of residence time distributions in large-scale ball mills is described. Tests are reported on a pilot-plant ball mill with 0.43 m diameter and 0.86 m length and on an industrial mill with 1.83 m diameter and 2.74 m length. Tests with different tracer feed sizes indicate that the residence time distributions on both mills are independent of charge particle size. Similar tests are planned for a large ball mill of 4.57 m diameter and 9.30 m length. No safety problems were encountered in these tests and none are anticipated in tests of the larger mill.

Jan 1, 1981

By W. K. Godfrey

The highest compressive strength cement has the highest bond strength in tests in which the cement is subjected to a confining pressure. After perforating, the bond strength is reduced to nearly zero when the pipe is supported by weak cement. Perforating does not affect the bond strength, however, when the pipe is supported by strong cement. Pipe supported by weak cement is damaged by perforating with expendable capsule jets, but is not damaged by perforating with the hollow carrier gun. High strength cements are recommended for oil wells that are to be perforated. Introduction The purpose of this work is to determine the effect of jet perforating on the bonding strength of oilwell cement at simulated down-hole conditions. Bond strength is a good criterion for determining the effectiveness of cement in performing its main function, i.e., that of isolating zones. According to the literature on the subject, the optimum cement strength for perforating is low and should not exceed 2,000 psi compressive strength. This conclusion was based on the appearance of bullet and jet perforations in neat and gel cements largely done in the absence of a confining pressure more than 15 years ago. Discussion Literature A relatively weak cement has been recommended in the literature as having optimum properties for perforating. In 1947, Oliphant and Farris tested bullet perforating of neat cements at various curing times.' Some of the tests were made at down-hole conditions. They reported that the optimum cement strength for perforating was about 2,000 psi compressive strength. Enlarged holes occurred when strength was too low, and the cement shattered and cracked when the strength was too high. In 1951, Morgan and Dumbauld tested bullet and jet perforating of neat and gel cements at surface conditions.' They reported that optimum cement has a compressive strength less than 2,000 psi. In their tests at atmospheric pressure, high strength cement shattered and cracked when perforated. Thus, the optimum cement strength was based on the appearance of neat and gel cement after perforating. In 1953, Clark showed a relation between cement strength and fluid shutoff.' He concluded that a 500 psi compressive strength is required for good fluid shutoff and that maximum bonding ability is developed at approximately 1,000 psi compressive strength. In 1964, Bell and Shore invalidated most of the conclu sions by the previous authors when they demonstrated that atmospheric pressure tests cannot be used to determine casing deformation and damage that will result from perforating under down-hole conditions.' They showed that the higher the hydrostatic pressure, the more restricted will be the expansion of gases generated by the charge. Less casing deformation and damage occurs under down-hole conditions than at atmospheric pressure. In recent work, Bearden et al. reported that jet perforating at surface pressure with the hollow carrier gun caused the cement sheath to shatter and crack.' The perforating, however, did not seriously affect the pressure required to leak past the casing cement bond. Only three cementing mixtures were tested, and presumably they had strengths in excess of 2.000 psi. Bearden et al. also reported that the hydraulic bonding strength increased as the compressive strength increased. Their hydraulic test showed that approximately 1,000 psi pressure is sufficient to break the casing cement bond for a well aged neat Portland cement sheath. Unfortunately, the tests were not run with a confining pressure, so Bearden et al. were merely measuring the strength of their outer 8%-in. casing. In our investigation, we measured the hydraulic bond strength of cement to pipe under a confining pressure and found that the bond strength was not limited to 1,000 psi. Cement Bond The bond strength is a good criterion for measuring the effectiveness of cement in performing its main function, that of preventing interzonal communication of fluids behind the casing. Measuring bond strength after perforating should be a good quantitative method of determining optimum cement properties, and should be a better method than that used by previous investigators,11 ' who simply observed the appearance of the cement after perforating.

Jan 1, 1969

By Richard H. Terhune

Slag and matte, in lead and copper smelting, are, for convenience of removal, tapped into pots of small capacity, usually of paraboloid form, of cast-iron, weighing 275 to 300 pounds, and holding the same weight of slag. As in many smelting districts one ton of ore makes a ton and a quarter of slag, a large number of pots is needed to equip an ordinary plant. Sudden and frequent expansion of the solid bowl causes the pots to crack at the bottom in a few months, and the matte, a very fluid sulpliide, enters these rough fissures and speedily corrodes its way through the vessel. 1 find, from one year of practice with a slag-

Jan 1, 1887

By Magnus Troilius

The heat-calculations of gas-analyses involve cumbrous multiplications, which are apt to lead into errors. The foliowing tables and formulae have been found useful as facilitating such calculations, and therefore I hope that they will be of interest to some of the members. By "heat-unit" will, in the following, be understood the amount of heat required to raise the temperature of 1 kilogram of water l° Cent. All the tables refer to cubic meters at O0 and 760 mm. pressure. The following gas is chosen as an example: C02, - 4.0 vol. per cent. co, = 20.0 " CHI, - 3.5 " H, - 7.0 " N, - 65.5 " " 100.0

Jan 1, 1884

By P. K. Koh, L. S. Birks, J. M. Siomkajlo

Direct identification in situ of x and a phase precipitates in stainless steel is possible with the electron probe microanalyzer. Although particles in the 1 p size range are too small to yield absolute percent composition, the relative % Crfi Mo ratio can be used to distinguish the two phases with better than 95 pct confidence. Wet chemical analysis of extracted residues gives Cr/Mo ratios in good agreement with electron probe results extrapolated to the 4 to 5 p size range. WHEN stainless steels are subjected to extended heating in the temperature region around 1600°F, precipitation of the brittle 0 or x phases may occur and impair the properties of the material. Identi-

Jan 1, 1961

By Ned Kuenhold

AN equipment manufacturer swallows a bitter pill when he sees his machinery improperly in- stalled and not used to the full potential. This frequently happens with vibrating screens. Screens can be classified according to the path of vibration imparted to the screen surface. On this basis there are: 1) vertical circle or modified circle throw, 2) horizontal circle or modified circle throw, 3) vertical linear reciprocation, 4) tilted linear reciprocation, and 5) horizontal linear reciprocation. The most versatile vibration for medium to coarse sizing is generally conceded to be the vertical circle produced by an eccentric or unbalanced shaft, but other types of vibration may be more suitable for certain screening operations, particularly in the finer sizes.

Jan 6, 1957

By R. D. Caudle, Yoginder P. Chugh, V. K. Agarwala

Longwall coal mining is a growing mining technique in the United States. However, very little premining exploration data are collected presently by coal companies to 1) select coal winning equipment, 2) select and design face supports and supports in gate and tail entries, or 3) optimize operational parameters such as length, width, and orientation of face. The authors are of the opinion that much of the data needed for mine planning and design for longwall mining can be obtained during exploration. In this paper, the authors identify the data requirements, discuss how these data can be obtained during exploration, propose an exploration program and estimate the cost to obtain the necessary data.

Jan 1, 1982

By R. C. Davis, R. F. Berry, G. W. White, B. T. O’Connell, L. A. Stacha

The formation density logging tool provides a radioactivity measurement that yields formation densities in situ. The relationship between bulk density and porosity is well understood. With knowledge of grain and fluid densities, porosity may be computed from the indicated formation bulk densities in shale-free formations. The porosities thus determined may be used with a resistivity log for water-saturation determinations. One technique utilizes a density vs resistivity plut. A plot of density vs Sonic-log transit time is used for porosity determinations in shaly sands. This method is particularly suited to wells drilled with oil-base or salt muds. In shale-free formations, comparisons of density values nnd neutron-log readings are used to identify lithologr and, thus, to select appropriate values of grain density for porosity computations. Through the use of Formation Density, Sonic and neutron logs, the interpretation problems caused by complex matrix lithologies are simplified. Other applications of the Formation Density log are found in the identification of minerals in evaporite deposits and in yield determinations of "oil shales". INTRODUCTION Widespread field application has demonstrated that the measurement of formation density is a useful and revealing technique for well logging. Responding to the bulk density variations of the formation, the Formation Density log affords valuable data on the porosity, lithology and fluid content of the formations. Although not without its own limitations, the Formation Density tool may provide effective interpretation under conditions that hamper or preclude the use of other porosity devices. When used in conjunction with other devices, such as the Sonic or neutron, complex matrix conditions may be better understood, defined and evaluated. A previous paper' described the valuable contribution of the Formation Density tool in the logging of empty, or gas-filled, holes. The purpose of the present paper is to describe applications of the device in liquid-filled holes. THE FORMATION DENSITY TOOL The Formation Density tool was devised to measure the bulk densities of formations in situ. Actually, the device responds to electron density, but in the overwhelming majority of cases of interest, the electron density is very closely proportional to the bulk density. In other cases appropriate corrections can be made if necessary. Comparisons of log-derived densities with true densities for the more common matrix minerals are shown in Table 1. The tool consists of a gamma-ray source and detector mounted in a skid which, during the logging operation, is in contact with the borehole wall (see Ref. 1 for schematic). Gamma rays are emitted by the source and diffused through the formation. The number of diffused gamma rays reaching the detector at a fixed spacing from the source are counted. An increase in counting rate by the detector indicates a decrease in bulk density in front of the skid. Conversely, a decreased counting rate signifies an increase in bulk density. A measurement of hole diameter, between the face of the skid and that of the eccentering arm, is recorded simultaneously with the measurement of diffused gamma rays. Since the tool is a wall-contact device, the size of the borehole has little influence, provided good contact is maintained with the wall of the hole. Only in extremely large or small boreholes does the actual diameter become significant. However, for most accurate measurements the borehole size should be taken into account. Fig. 1 presents the departure curves for the conversion of counting rate to bulk density for liquid-filled holes of various sizes. It is of utmost importance that the skid maintain good contact with the wall of the hole. If, due to roughness or caving, there is mud between the skid and the formation, the tool will include in its response the relatively low-density mud, and the apparent density reading will be too low. Normally, permeable beds do not cave appreciably, so that reliable readings are usually available for zones of interest. Nevertheless, the caliper reading over the zone of interest should be examined for any wall roughness. When mud cake exists between the skid and the formation, the Formation Density log sees it as part of the formation. When thick mud cakes exist, a correction is required. For best results in wells having thick mud cakes,

The Mining Enforcement and Safety Administration has called attention to the increasing frequency of accidents occurring during mine maintenance and repair tasks in a recent publication. Data from the agency's Health and Safety Analysis Center have been compiled and presented in a report titled "Analysis of Injuries Associated with Maintenance and Repair in Metal and Nonmetal Mines,"* a booklet aimed at answering four questions: (1) Which pieces of operating equipment are most frequently involved in maintenance accidents; (2) Which maintenance functions are the most hazardous; (3) Which tools are most often associated with injuries; and (4) What is the comparative hazard of welding or flame cutting vs. mechanical or electrical maintenance functions.

Jan 3, 1978

By O. Saeki

Dolomite-fluxed pellets have been produced at Kakogawa Works, Kobe Steel, Ltd., since August, 1975. The pellets contain 5.5 % dolomite and have a basicity (CaO/Si02) of 1.3. By charging 30-50 % of dolomite-fluxed pellets into the two large blast furnaces at Kakogawa, a low fuel rate of 450 kg per ton of pellets has been achieved with better furnace permeability and gas utilization. Laboratory studies show that dolomite-fluxed pellets have excellent high temperature properties, and that their softening and melting-down temperatures are about 50°C higher than those of lime-fluxed pellets, and that reducibility at 1250°C is increased from 25 to 70 %.

Jan 1, 1977

By J. A. Finch, S. T. Hall

An oxidative alkaline pressure leach is shown to increase the magnetic susceptibility of coal-pyrite particles. The leach was successfully exploited as a pretreatment in the magnetic desulfurization of an eastern Canadian coal. Greater than 50% total sulfur (65% pyritic sulfur) rejection at 85% clean coal yield was achieved using a high-gradient magnetic separator (HGMS) at 1.3 T and 53 mm/s (2 in. per sec) flow rate, after pretreatment at 0.5 mot NaOH, 85ºC (185ºF), 930 kPa (135 psi) air pressure, 15 minutes retention time, and 20% solids by weight (w/w). Without pretreatment, sulfur rejection at these HGMS settings was less than 5%.

Jan 1, 1985