Search Documents

By Reynold Q. Shotts

CHEMICAL methods, based on the relative rates of oxidation of fusain, bright coal, and dull coal by nitric acid, have been devised to determine these coal components.1-4 Results obtained by oxidation methods for fusain have been checked against results obtained from microscopic methods5, 6on duplicate samples of the same coals, but to the author's knowledge this has not been done for bright and dull coal components. For this reason it is not certain that the two methods of analysis identify essentially the same chemical or physical units. It would be highly desirable to see results of the application of both methods to duplicate samples, but in the absence of any such data the author has attacked the problem indirectly. From the U. S. Bureau of Mines samples were obtained of three Alabama coals which the USBM had analyzed optically and reported on over the past 30 years. These samples were subjected to analyses by oxidation rate methods. Results of this work, and comparisons with the USBM analyses, have been published." This was the first indirect approach to the problem. The present report attempts a second indirect approach by way of internal validation. By nitric oxidation samples of two whole coals were carefully analyzed for fusain, bright coal, and dull coal. One coal was analyzed in duplicate. Duplicate portions of each of the coals were divided into three density fractions by means of heavy liquids. A duplicate portion of one of the coals was divided by sieving into three size fractions. Each fraction was analyzed by oxidation and its percentage composition calculated in terms of fusain, bright coal, and dull coal. Because the weight percent of each fraction was known, a material balance calculation for the whole coal was also made. The resulting reconstituted analysis of the whole coal could be compared to that determined by direct analysis. In addition, specific reaction rate constants were determined for each component and for each whole coal or fraction. Arbitrary reactivity indexes were calculated by dividing by 100 the sum of the products of the percent of each component in the coal and its specific reaction rate constant. The resulting figure was an average reactivity index for each coal or fraction. Weighting the reactivity indexes for each fraction by the percent of the fraction in the coal gave a reactivity index for each whole coal which could be compared to that calculated directly from the whole coal analysis. If oxidation analyses really delineate definite physical entities within the coal, or even definite groups of similar entities, reconstituted analyses calculated from fraction analyses should check closely those made of the whole coal. It probably is true that optical methods identify and describe a greater variety of components than do chemical methods and that variations are wide in the appearance and quantity of those components identified optically. Chemical methods based upon differences in oxidation reaction rates would of necessity be less discriminating, as between similar components, than would optical methods. The procedures followed for oxidizing the samples, analyzing the residues, plotting and calculating the percentage of each component, and calculating its specific reaction rate constant have been fully described.'-' In brief the method originally proposed by Fuchs et al.1 for the determination of fusain consists of the oxidation of small samples of coal in boiling 8N nitric acid in a condenser-fitted flask. After boiling for periods of 1/2 to 4 hr, the unoxidized residue is filtered and washed. The washed residue is treated with normal sodium hydroxide, diluted, and allowed to stand for several hours. The resulting brown liquor is removed, and the filtered residue dried, weighed, ignited, and weighed again. The ash-free residue is expressed as a percent of original dry, ash-free coal. The percent residue is plotted against time, and the extrapolation of this line to zero time gives the percentage of dry ash-free fusain present in the original sample. The shape of the resulting time plots has been explained' by the assumption that they are the result of two different types of reaction, the first part representing a first order reaction with rate a func-

Jan 1, 1956

By A. J. Jacobs, J. W. Spretnak, R. Speiser

The activities of nickel in liquid iron-nickel solutions containing from 10 to 90 at. pct Ni were measured over the temperature range .1510° to 1600°C. A special function was devised whereby activities can be computed by a graphical integration using the results of chemical analyses on the vapor phase alone. The liquid solutions studied exhibit negative deviation from Raoult's law, but they approach ideality as the temperature is raised from 1510° to 1600°C. The maximum heat of solution is less than -8.0 kcal per mole. The entropy of solution is less than —2.5 kcal per mole deg at 1510°C, and changes negligibly as the temperature is raised. The liquid iron-nickel solutions do not follow regular solution behavior. THE activities of the components of a liquid alloy system can be determined in favorable cases from the partial pressure of the vapor in equilibrium with the liquid alloy.' Assuming that the vapor over the alloy behaves as an ideal gas, the activity of component i is given by the expression, Where the superscripts 1, v, and o signify the liquid, the vapor, and the pure component, respectively; the f's are the fugacities, and the P's, the pressures. The quantities Pi and Pi can be determined by the

Jan 1, 1960

By F. Keller, E. H. Dix, R. W. Graham

Aluminum alloys containing relatively small amounts of magnesium and silicon are of commercial interest because they are readily workable in the annealed form and may be hardened and strengthened by suitable heat treatment. An intermediate temper can be produced in these alloys by quenching after a Solution heat treatment and the alloy in this condition can be formed easily. Artificial aging is required to obtain the maximum mechanical properties but this aging does not cause distortion nor require elaborate heat-treating equipment. The hardening of the alloys after quenching is attributable in part to the retention of the compound Mg²Si in solid solution, while the maximum hardness obtained by subsequent artificial aging is attributed to the fact that the solid solubility of the compound Mg²Si in aluminum decreases with decreasing temperature. Considering the importance of aluminum alloys susceptible to heat treatment, it is surprising how few fundamental investigations have been carried out on the aluminum-magnesium silicide alloys. This paper deals principally with the solid solubility relations of the compound Mg2Si in aluminum and is the sixth paper of a series1 from the laboratories of the Aluminum Co. of America reporting the results of investigations of equilibrium relations in aluminum-base alloys made from high-purity aluminum."

Jan 1, 1931

By Gen-Hua Shi, Richard E. Goodman

In hard, discontinuous rocks, failure modes and stability are controlled to a great extent by the intersection of discontinuities with the excavated surface. We have solved the general problem of finding the shape and size of all blocks formed through the inter- section of any number of joints and excavation surfaces and will demonstrate a simple graphical method for determining which of these is the "keyblock." An example will explain this methodology applied to a simple open pit. The effects of slope curvature in plan or section, will be demonstrated. Finally, we will show how to determine the optimum orientations for the cut slopes. The methodology is based upon a powerful topologic theorem concerning the finiteness of spatial intersections. This paper is a companion to another dealing with underground openings in the Proceedings of the 22nd Symposium on Rock Mechanics (MIT) , July 1981. This paper discusses the rock blocks created by the intersection of discontinuities and excavation surfaces in a rock mass. It establishes principles and procedures by means of which those blocks that are finite and critically located can be identified and described. The main assumptions are the following: 1. The rock itself is assumed to be strong so that the only concern for stability is the movement of rock blocks them- selves.

Jan 1, 1983

By Hermann Irresberger

SUMMARY In the German hard coal industry, relevant parameters influencing strata control have been identified in many years of intensive research work. The research results allow the formulation of the technical requirements on the design of shield supports as a function of the geological and operational conditions the face machinery is subject to. Keys to strata control are support resistance adjusted to the individual conditions of application and the tip-to-face interval. The technology to implement these requirements in actual operation is available. The automation of the shield-advance work cycle, currently setting in, can further contribute to improve strata control. In doing so, however, we must not forget the demand for an unsophisticated and low-cost design of shield supports with high operational safety. INTRODUCTION The German hard coal mining Industry produces coal from flat and inclined seams in depths between 400 and 1,300 m. The coal is exclusively won by longwall working involving face lengths up to 280 m. The thickness of the seams being worked is between 0.7 m and 4.5 m. Coal winning is fully mechanized with drum shearers or coal ploughs; two, three, or four leg shields are predominantly used as supports.

Jan 1, 1984

By Georges Fleming

The new burden preparation plant of ARBED Luxembourg, Belval- Works, which comprises 2 large sinter strands, is equipped with a process computer connected to a comprehensive process control system. The main jobs done by the computer are the control of the raw mix composition, and thus the monitoring of the stacking of the piles at the bed-blending plant, and the optimization of the sintering process. Among the optimization criteria, quality is considered as the most important. The sinter quality, characterized by the mechanical strength and the state of oxidation, is controlled automatically. The control system which we have dev loped is highly reliable; as a result, the standard deviation of Fe++, for the control of bivalent iron, has been narrowed to 0,5 % and the standard deviation of the IS0 + 6, 3 mm index, for the control of the mechanical strength, has been kept within 1 %. Thanks to these results, the combined savings in fuel consumption at the sinter plant and at the blast furnaces have covered the total costs of the optimization project in 2 years. By applying automatic control, the optimum driving range of the sinter plant has been defined and these new guidelines are used for monitoring the sinter production.

Jan 1, 1977

By Lee W. Abramson

INTRODUCTION The design of rock support for underground nuclear waste repositories requires consideration of special construction and operation requirements, and of the adverse environmental conditions in which some of the support is placed. While repository layouts resemble mines, design, construction and operation are subject to quality assurance and public scrutiny similar to what is experienced for nuclear power plants. Exploration, design, construction and operation go through phases of review and licensing by government agencies as repositories evolve. This paper discusses (1) the various stages of repository development; (2) the environment that supports must be de signed for; (3) the environmental effects on support materials; and (4) alternative types of repository rock support. Much of the information presented in this paper was derived from work conducted for Basalt Waste Isolation Project. Most of the information, however, would apply to other hard rock repositories. REPOSITORY DEVELOPMENT AND THE NEED FOR ROCK SUPPORT Repository development can be characterized by five general stages: exploration and design, excavation, waste emplacement, re trievability period, and backfilling. It is helpful to understand these phases of development to see where and when rock supports are required and how the design is verified. The description that follows is simplified. Details have been omitted, and future plans may not conform to this scenario.

Jan 1, 1984

By P. B. Liebermann

1. Haulage Tests on Coal-mine Cars THE haulage of coal from the face to the tipple is an important enough link in the production of coal to deserve its full share of study and care. In order to obtain a better understanding of mine haulage conditions, a series of tests and investigations has been made which promises to hasten the improvement of present conditions. For hauling coal through the mine and on the surface, locomotives are required, the size and power consumption of which depend on the resistance to motion offered by the mine cars. This resistance is principally caused by gravity and hearing friction. The effect of gravity can be reduced to a minimum by a suitable layout of the haulageways; that is, by arranging the grades in favor of the loaded trips, and by fixing the percentage of grade to that value which gives the lowest power consumption for loaded and empty trains. The bearing friction, which is considerably greater than is generally realized, can be easily reduced to a negligible quantity by the installation of a suitable anti-friction bearing that will stand the rough use and abuse of coal-mine service. The present investigation will deal with flexible roller bearings in comparison with ordinary plain bearings.

Jan 7, 1917

By I. N. Zavarine

The observations presented in this paper were recorded during a study of the spheroidizing process. Spheroidization of cementite in steel is either brought about to develop a set of desirable mechanical properties or is an incidental result of mechanical and heat-treating manipulations. Physical properties of steel are materially influenced by the state of the cementite. Conversion of cementite from the lamellar to the spheroidal state is usually accompanied by a decrease of hardness and of strength and by an increase in ductility. The spheroidized structure is usually considered as an ultimate step in the process of the softening of steel. The unorthodox hardening of a 3.5 per cent Ni steel (SAE No. 2330) after a heat-treatment that previously proved entirely suitable for a complete spheroidization of cementite in carbon steels led to the observations that constitute the subject of the present paper. Experimental Procedure The steels used for the experiments described were bought on the market. All were in the form of 3/4-in. round bars. Their chemical compositions are given in Table 1. The spheroidization of cementite in steels can be obtained in several ways. The method used in the present work is, perhaps, the least known. It consists of cyclic heating and cooling of steel, the temperature being

Jan 1, 1939

By I. N. Zavarine

The observations presented in this paper were recorded during a study of the spheroidizing process. Spheroidization of cementite in steel is either brought about to develop a set of desirable mechanical properties or is an incidental result of mechanical and heat-treating manipulations. Physical properties of steel are materially influenced by the state of the cementite. Conversion of cementite from the lamellar to the spheroidal state is usually accompanied by a decrease of hardness and of strength and by an increase in ductility. The spheroidized structure is usually considered as an ultimate step in the process of the softening of steel. The unorthodox hardening of a 3.5 per cent Ni steel (SAE No. 2330) after a heat-treatment that previously proved entirely suitable for a complete spheroidization of cementite in carbon steels led to the observations that constitute the subject of the present paper. Experimental Procedure The steels used for the experiments described were bought on the market. All were in the form of 3/4-in. round bars. Their chemical compositions are given in Table 1. The spheroidization of cementite in steels can be obtained in several ways. The method used in the present work is, perhaps, the least known. It consists of cyclic heating and cooling of steel, the temperature being

Jan 1, 1939

Mineral Industries education as an entity, again and again has sought recognition, always to be turned aside or ignored.1 The incident mentioned in Lost Chapter was only the first of a series of disappointments. The Land-Grant Act is camouflaged here and there in the name of progressive education. A new interpretation may be in the best interests of society in so far as the goose is not killed that lays the golden egg. The primary objective of the act is still "agriculture and mechanic arts" but mechanic arts is not alone mechanical arts or engineering. Mechanic arts was used in a broad sense as a symbol of creative effort in locating and winning the fundamentals of existence - plants, animals, and minerals - from Mother Earth, their primary processing and treatment into foodstuffs and raw materials of industry, their manufacture into useful articles of commerce, and, last, their distribution and utilization. Significantly the great agricultural industry is now at least half mechanic arts. The Association of Land-Grant Colleges and Universities has neglected the mineral kingdom shamefully. The Association embraces Divisions of Agriculture, Arts and Sciences, Engineering, Home Economics, and Veterinary Medicine but has no division relating to the mineral industries.

Jan 1, 1950

By John D. Morgan, Sylvain J. Pirson

AN instantaneous and continuous analysis of a mineral suspension should be of great value in controlling various mineral preparation processes. Described herein is a method of analysis based on the use of high-frequency alternating current, which, under certain restrictive conditions, could be of use. THEORETICAL CONSIDERATIONS In a suspension of conductive minerals, the electrical effect primarily responsible for the variations in electric conductivity is the capacitance. In Fig Ia, let an alternating voltage E be applied across two electrodes F and F', between which are two rows (S and T) of mineral particles, all of approximately the same size, immersed in a fluid. Let the number of rows of particles between the electrodes be R and the number of particles in each row be N. If A is the area of a particle, D is the distance separating two particles, and K is a constant depending on the fluid, the capacity, Co, of the particle system will be given by: [KRA C0 ND] Referring now to Fig Ib, let R, the number of rows, be held constant, but let N, the number of particles in each row (S and T), be increased X-fold. The capacity, C1, of [ ]

Jan 1, 1947

By Ronald A. Murdock

INTRODUCTION Exxon's Highland Uranium Operations in eastern Wyoming consists of an open pit, an underground mine and a mill complex. The geology of the deposit is reviewed in this paper, and an overview of the mining operations at both the surface and underground mines is presented. Topics discussed include geology, stripping of overburden and mining of ore in the open pit, and underground development and stoping methods. GEOLOGY The Highland uranium deposit was discovered in 1968 by Exxon Minerals Company, U.S.A., in Converse County, Wyoming, 35 miles north of Douglas. The mine is located at an elevation of about 5,200 ft in a high-plains, sagebrush-covered prairie typical of eastern Wyoming. The deposit is near the southern edge of the Powder River Basin in the Paleocene Fort Union Formation. The Fort Union Formation consists of 1,900 to 3,200 ft of sandstone, siltstone, mudstone, claystone and coal beds. Siltstone, mudstone and claystone are collectively referred to as "shale" at Highland. There are many alternating layers of shale and sandstone in the Fort Union Formation; but in the Highland area, there are only three principal sandstones, known as the Highland Sand Group, which host the uranium. The combined sand thickness is about 150 ft.

Jan 1, 1983

By A. M. Gaudin, T. P. Meloy

Based on the equation for single fracture, a formula has been obtained for repeated fracture. Solution of this equation is obtainable analytically for a few examples and numerically for all others. Graphs of the size distribution equations have been obtained; they agree broadly with the experiments of others. In another paper1 we have considered a model and a comminution distribution equation for single fracture of brittle materials. Most comminuting devices, however, depend on the occurrence of repeated fracture. This is especially true of continuous cylindrical mills of the ball, tube, or rod type. But even in primary crushers there is some repetition of the breaking process, so that this paper should be of interest in connection with all comminuting devices. HALF LIFE AND PROBABILITY OF FRACTURE To facilitate the study of fracture it is useful to introduce the concept of the half life of a particle, In the ball mill, for example, we may start with 10,000 feed particles. The time, 7, by which one half of these particles have been broken is the half life of the feed under the prevailing experimental conditions. The probability of breakage bears an inverse relationship to the half life. In a ball mill, for instance, it can be shown that the

Jan 1, 1962

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

The object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,' but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding"2 method, in which a seriesr of measurements is made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is determined at a given station for various increasing thicknesses of the ground.

Jan 1, 1934

A professional and special section of the United States Employment Service, Department of Labor, has been created for the purpose of aiding officers and men who have been discharged from military service, but who, for various reasons, cannot resume their former positions, to place themselves in industry without loss of time. Its work is carried out in conjunction with the Engineering Societies Employment Bureau. The machinery of this new professional section is being set up as rapidly as possible, and an office is already in operation at 16 East 42c1 St., New York. The work in the New York State district is under the direction of Mr. Henry Bruere, formerly City Chamberlain of New York City. Dr. Thomas T. Read, Chairman of the A. I. M. E. Committee on Industrial Organization, has charge of the clearance between the State offices of the Eastern States. This service is designed for the purpose of placing not only men in the engineering professions, but for all other kinds of professional and highly trained, skilled men. Full details regarding the qualifications desired in a man should be given, so that employers may be put in touch only with such available men as will fully qualify for the positions.

Jan 2, 1919

By W. A. J. M. Van Waterschoot Van Der Gracht

The commercial production of petroleum in Germany is confined to the North German plain, in the Hereynian foreland, and the intramontane Permian salt basin of Thuringia, south of the Hare Mountains. Petroleum is produced in the former only in connection with salt domes, upthrust through Tertiary and Mezozoic strata of great thickness. In the basin of Thuringia petroleum is found in a Permian dolomite underlying a salt formation. It is exclusively in the peripheric zone of a few of the salt plugs in the North German plains region that commercial oil has so far been developed, notably in the following fields, all in the general region northeast of the city of Hanover: (1) Hänigsen-Obershagen-Nienhagen, south of Celle; producing from horizons in the Upper Triassic, the Middle Jurassic and the Lower Cretaceous; (2) Oberg, south of Peine; producing from horizons in the Middle Jurassic and Lower Cretaceous; (3) Oelheim-Eddesse, north of Peine; producing from horizons in the Upper Triassic, Lower and Middle Jurassic; (4) Wietze, west of Celle, where the main producing horizon is in the Lower Cretaceous. In some of these oil fields production from surface seepages was mentioned as early as 1669 (Oberg). Commercial production of importance dates only from recent time.

Jan 1, 1932

By L. W. Kempf

THE thermal conductivity of aluminum alloys is of considerable indus-trial importance. This is particularly true in such applications as inter-nal-combustion engines where one of the principal reasons for the use of these alloys is their relatively higher thermal conductivity. In spite of this, relatively few data are available on this property of aluminum alloys. The reason is quite apparent to anyone concerned with the experimental determination of coefficients of thermal conductivity. This determina-tion, in theory so simple, is extraordinarily difficult if any high degree of precision is desired. Fortunately, some knowledge of the relationship between thermal and electrical conductivity has permitted the use of the latter physical property in deducing the relative approximate-values of the thermal conductivities of metals. This fundamental relationship, first enunciated by Wiedemann and Franz1 as applying to metallic elements and later shown by Lorenz to be applicable to alloys within a single metallic system, has been of service in the industrial application of metals. The electrical conductivity of metals is easily determined with a high degree of precision. It is, therefore, quite desirable that the relationship between electrical and thermal characteristics be determined with the greatest possible precision. This paper presents data on the electrical and thermal conductivities of a number of aluminum alloys of industrial importance.

Jan 1, 1937

By Robert G. Van Nostrand, John H. Henkel

TRANSIENT potentials obtained in resistivity prospecting can be separated into two classes. The first is electromagnetic, has a comparatively short time constant, and increases in relative amplitude as the electrode separation is increased. These electromagnetic transient potentials, of which an excellent theoretical treatment is given by Yost,1 are the result of changes in the current and can be classed as differentiated signals. The second class is electrochemical, has a comparatively long time constant, and decreases in relative amplitude as the electrode separation is increased. The electrochemical signals are generated by the current flow itself and can be classed as integrated signals. The transient potentials due to electrochemical factors are the subject of this article. The phenomenon is referred to as induced polarization. Schlumberger2 was the first worker to observe induced polarization, but he was unsuccessful in attempts to apply the principles of induced polarization in electrochemical prospecting. Other workers, notably Bleil3 have studied polarization and in some cases pointed out its possibilities, but no theory has been presented that describes polarization and its time dependence adequately. It is the purpose of this discussion to present the essence of a theory to geo- physicists and to show that it leads to results consistent with experimental evidence. The theory on which this analysis is based has existed in electro- chemical circles since 1910.4

Jan 3, 1957

By R. V. Ramani, Robert Stefanko

The more stringent ventilation requirements of the 1969 Act have created a greater need for improved network analyses. More air is required at the last open crosscut (9000 cfm) and for the first time a minimum quantity is specified for the face (3000 cfm). Severe restrictions are placed on both belt and track haulage, and the intake air cannot contain more than 2 mg per cu m of respirable dust, to be reduced to 1 mg later. Larger tonnage and longer life mines are the trend today, necessitating multiple fans and shafts. Yet relatively little engineering goes into designing the mine ventilation system. In this paper a ventilation system is designed for a typical Pittsburgh block system, manual calculations are made and then checked by a computer solution. The computer is the ideal tool to try out proposed changes on paper to insure that the entire mine is properly ventilated and no costly adjustments need be made by dumping air. While it is theoretically possible to solve complex ventilation network problems by hand, it is not practical to do so because of the tremendous man-hours required and the many opportunities for errors. Thus the digital computer is indispensible to the ventilation engineer and newer improved ventilation programs are being developed to more realistically model mine ventilation networks. Suggested ventilation changes to comply with the new regulations are also critically evaluated.

Jan 1, 1973