Search Documents

By G Simpson, S Dressler, A E. Levett

Tailings storage facilities often represent a mining operation’s most significant liability, posing serious environmental, social and safety risks. Almost all mining operations dispose of wet tailings (Valenta et al, 2023), which represents a risk of failure due to the potential for a rapid strength reduction of the unconsolidated materials leading to static liquefaction and subsequent dam wall failure. As a waste stream, tailings disposal, decommissioning and relinquishment aim to be inexpensive processes, ruling out many highly engineered solutions. Advantageously, tailings consolidation does not need to be immediate, opening the door for relatively passive, inexpensive consolidation methods that aim to gradually increase the strength of tailings over extended periods (ie years). In this paper, we present the prospect of novel in situ tailings stabilisation, learning from studies that have investigated the most erosion-resistant landforms on Earth.

Aug 2, 2023

By Kuganathan V

The processing of black coal in Australia segregates waste in the form of coarse reject and fine tailings. The coarse reject is relatively easy to handle, while the tailings can be problematic. Conventionally, the two waste materials are disposed of separately, the coarse reject in dumps, and the tailings in man-made containments. Aqueous tailings slurry is pumped to a 'wet' tailings storage, where the fine particle size of the tailings limits dewatering. Their low bearing capacity and high compressibility result in tailings deposits being difficult to rehabilitate. Disposing of the waste streams separately moves away from the heterogeneous mixture in the undisturbed ground, and concentrates potential problems with each waste stream. The feasibility and desirability of the co-disposal of tailings and coarse reject by combined pumping is demonstrated. This technique is in operation at Jeebropilly Mine and is proposed for a number of other coal mines.

Jan 1, 1992

By C Lower

An unprecedented, quantitative, deposit-scale understanding of major clay mineral distribution throughout the Yeelirrie uranium deposit has been achieved by adapting the existing HyLogger™/HyChips™ analytical technique to measure resource assay pulps. Spectral analysis via HyLogger™ and HyChips™ systems has previously been used as a small-scale geometallurgical research tool, but never before has it been quantitatively applied to an entire resource sample population for the purpose of developing stand alone block models for major clay minerals. Economic uranium mineralisation within the thin but extensive Yeelirrie?palaeochannel?primarily exists within the transition zone between a groundwater-derived calcrete and the underlying clay-quartz regolith. Early geometallurgical investigations identified that certain clay minerals could be deleterious to the efficiency of the uranium recovery process. Accurate calculation of clay mineralogy from resource assays proved too difficult due to chemical similarities between co-existing kaolinite, smectite and magnesium carbonate minerals. A relatively low-cost, efficient and accurate method of quantitative clay mineral analysis was required to measure over 70 000 resource assay pulps. After initial testing and comparison with QXRD, the HyChips™ 3-1 spectral logging system was implemented as a primary method of clay mineral analysis for the Yeelirrie uranium deposit. The resultant spatial data set allowed the interpretation and geostatistical analysis of geometallurgical domains across the deposit. Clay block models were generated and used in geometallurgical resource calculations to benefit the mine planning process.

Sep 5, 2011

The need for formalised geotechnical reporting has not been fully explored at many operations. With the continuing need to provide safer and more efficient workplaces, the requirement for good geotechnical reporting systems (as with other reporting systems) has become of greater importance.Historically, the risk from rockfalls has been the largest cause of fatal injuries in the underground mining industry. The response of the ground to mining is generally poorly documented at many mines. At Olympic Dam, it was found that the existing corporate hazard and incident reporting (HIR) procedure did not record enough specifics about geotechnical issues. A separate and more specific geotechnical reporting process was set up to address this problem.This paper examines the role that geotechnical reporting plays at the WMC Resources Olympic Dam Mine; from reporting and rectifying day-to-day geotechnical issues that affect the operation to documenting and analysing longer term trends.

Jan 1, 2004

By C Linklater, A Garvie, D Kentwell

Various Australian and international regulatory bodies (Environmental Protection Authority, 2015) require an early assessment of the geochemistry of waste rock. This usually includes estimates of the locations and volumes of potentially acid forming (PAF) materials and requires sampling of the waste rock zones as well as submitting the samples for a series of tests. We know that the required number of samples will vary depending on rock type, mean sulfur levels and spatial variability of sulfur as well as total volume. The key question is how do we know when we have enough samples?This extended abstract describes the application of geostatistical methods to examine how sample numbers and sample locations influence the preliminary conclusions that may be drawn for early stage waste characterisation.CITATION:Kentwell, D, Garvie, A and Linklater, C, 2016. Geostatistics and sample numbers from an acid and metalliferous drainage perspective, in Proceedings Life-of-Mine 2016 Conference , pp 12–15 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Fuller P. G, Dugan K. J

Artificial support can be used to improve wall stability in open pit mines. This is examined for a particular case where the factor of safety for a slope is kept constant by using artificial support as the slope angle is increased. It is demonstrated that the savings in excavation generally exceed the cost of support. However, in order to correctly judge the eco- nomic impact of artificial support on the project, all the elements relat- ing to the use of artificial support must be taken in account.

Jan 1, 1989

Methane is present in varying degrees in nearly all underground coal mining operations. At mixtures with air near 5-15% it is explosive and consequently since it is not usual for these levels of contamination to be reached in the general body of a mine ventilation system it is not unusual to experience it in specific places. On longwall faces the most used power loader is the shearer machine and because of its general shape, situation and operation it is likely that all the factors which are required to cause a frictional ignition can be present. This paper makes a general appreciation of the causes of these ignitions and methods which are and have been used to control these situations on and around these machines.

Jan 1, 1981

The capacity of chlorine based solutions to rapidly and effectively dissolve coarse gold in oxide ores is well established. The inherent advantages of chlorine are high dissolution rates (10 - 100 times those of cyanide), and low cost. The high dissolution rates mean that coarse or poorly liberated gold may be dissolved over relatively short periods and hence ore particle size may cease to be such a critical factor. The cost of size reduction to allow adequate gold liberation in order to achieve an adequate gold recovery is less of a consideration when using chlorine than in traditional plant or heap leaching cyanide-based treatment systems.Because chlorine based solutions capable of dissolving gold evolve an unpleasant vapour phase with the potential for significant chlorine losses into the atmosphere, traditional heap leaching with active solutions being sprayed onto prepared heaps is not possible. The ore must be covered and the solution may be introduced beneath that cover through prepared injection `wells' and recovered through production 'wells'. The pit is flooded with active solution beneath an overburden or cover with the solution migrating from the injection 'wells' to the production 'wells' over a period of around five - ten days.

Jan 1, 1992

By M Slight, H Lacy

In recent times, with the global mining industry’s focus on sustainable development there has been a significant focus on mine closure and rehabilitation performance and reporting through the development of the International Council on Mining Metals (ICMM), the Global Reporting Initiative and the Equator Principles. In addition, financial reporting obligations under International Financial Reporting Standards and the Sarbanes Oxley Act (2002) have also led to better understanding and improvements with industry closure performance, liability management and reporting.Under these sustainable development principles and financial reporting obligations, mining companies are required to consider mine closure planning and associated cost estimates across all life cycle phases of the mine. Internal processes have been developed within mining companies to better understand their closure liabilities and obligations and likely costs and cost estimating processes are generally developed for long-term life-of-mine (asset) planning and budgeting, financial reporting for corporate balance sheet provisioning purposes, and regulator reporting for environmental bonding and financial assurances.These days mining companies need to plan for, prepare and actually mine for closure right from the start of a project. This means that their closure and rehabilitation liabilities throughout each stage of the mine life cycle phases must be understood, planned for, managed and controlled.So how is the industry performing? Understanding of closure liabilities is improving and reflected in liability cost estimations that are recognising the likely issues to be faced at closure, but there is a way to go to ensure that the industry doesn’t add to the increasing legacy liabilities being passed onto the wider community.CITATION:Slight, M and Lacy, H, 2016. Closure liabilities – where are we at?, in Proceedings Life-of-Mine 2016 Conference , pp 28–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Else D

While the underground mining work environment may have processes and equipment considered unique, most of the broad issues likely to affect the occupational health and safety of employees are not. One such occupational health and safety issue that is common to the mining sector and most other industries is noise. Noise as an occupational health and safety issue is of national significance. Presently noise induced hearing loss costs Australia around $35 million per year on compensation claims experience alone. Noisy equipment and work environments are still being tolerated in parts of the mining industry as `part of the job'. Where work has been undertaken in noise management, considerable emphasis has been placed on either industrial hygiene monitoring programs or the provision of hearing protectors to miners working on or around noisy equipment.Opportunities for more cost-effective and long term methods for controlling noise exist. Ready to apply solutions to noise problems in the mining industry are available, but for many mining operators this information is often difficult to obtain. To overcome this problem, the SHARE program collects and distributes solutions to occupational health and safety problems. The program aims to help organisations to close the gap between what is known about solving health and safety problems and what is actually being applied at the shop floor level: Recent developments have incorporated the SHARE program concept into worksite hazard management projects that involve the participation of employee representatives, front line supervisors and engineering personnel. Besides providing workforce members with an increased understanding of hazard management skills, the SHARE in-house program results in the implementation and sharing of solutions to health and safety problems by the program participants.

Jan 1, 1992

By G Anderson, V Lawson, P Voigt

Glencore operates zinc concentrators at both Mount Isa and McArthur River. Both orebodies have a history of complexity and required the development of new technologies to maximise the value from these long-life assets. The Mount Isa orebodies were plagued since operations started in 1931 with complex mineral textures making separation challenging and many areas uneconomic. Examples are given in Figure 1 with different grain sizes from the same orebody in different areas. The McArthur River deposit, located in the Northern Territory, was discovered by Mount Isa Mines geologists in 1955 (Logan, Murray and Williams 1990). The extremely fine-grained nature of the ore was quickly recognised and the difficult separation of the minerals was soon obvious. The geographical, metallurgical and economic factors resulted in the orebody not being developed until the technologies for the mineral separation had been developed. The development of the IsaMill allowed for an economic mineral separation flowsheet to be developed and ore treatment commenced in May 1995 (Nihill, Stewart and Bowen 1998). CITATION: Lawson, V, Anderson, G and Voigt, P, 2018. Developing technologies for a complex orebody, in Proceedings Complex Orebodies Conference 2018, pp 116–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Badal R

Rock Discontinuities ("joints") affect blasting results. An investigation was carried out to understand if blast parameter such as spacing needs to be altered with the change in joint direction. Small scale laboratory studies in jointed limestone blocks have been carried out. It is shown that optimum spacing is variable with the "joint" orientations. Evidence is presented from field studies in four limestone quarries supporting laboratory studies. Reasons for success and failure of widespacing technique is also provided. Only with suitable orientations of "joints: widespacing is successful.

Jan 1, 1990

By Cutmore NG

The moisture content of iron ore is important in handling, stockpiling, transport and further processing operations. Typically these ores contain both `free' and `bound' moisture, the latter being moisture that is not removed in a conventional laboratory determination of moisture by air drying at 105¦C, and it is the free moisture that is important in dust control and ore handling. The CSIRO Division of Mineral and Process Engineering has previously developed and commercialised gauges, based on capacitance and microwave techniques, for the on-belt determination of moisture in coal and minerals. However, these gauges determine total moisture, and have a different sensitivity to free and bound moisture in the material analysed. Consequently, the accuracy of determining total or free moisture alone may be significantly affected by variations in the bound moisture content. An investigation has been carried out on the simultaneous determination of free and bound moisture in iron ore fines (

Jan 1, 1993

The Mount Sisa orebody on Misima Island, P.N.G., consists of goldsilver mineralisation associated with massive carbonate and amorphous iron-manganese oxides in fractures and breccia matrix. The orebody forms the northern extension of the Umuna deposit, which lies within a three kilometre strike length of a northwest trending, 300 metres wide, high angle fault zone. The structure is deeply oxidised, with the magniferous oxide material resulting from oxidation of carbonate. The wallrocks are metamorphosed basement psammopelites and basic volcanic rocks, extensively intruded by microgranodiorite. These are dominantly epidotised and sericitised. The precious metals are associated with anomalous Cu, Zn, Pb, Mn, As, Ba, Ga, Sb, and Mo. Many of the features of the Mount Sisa mineralisation are characteristic of volcanic-hosted epithermal deposits of western North America.Lithologic and textural gradation is observed between the carbonate hydrothermal breccia-fill at Mount Sisa, and the quartz dominated brecciafill and dilational fracture-fill mineralisation which forms most of the Umuna deposit to the south. This gradational relationship is analogous to that in the Amethyst-OH vein system at Creede, Colorado, where it is shown to be indicative of deposition from laterally migrating fluids.

Jan 1, 1988

By Tagawa H

In Japan, geological condition do not only vary in a wide range of strata but are also extremely complex with the existence of faults and aquifers. With respect to rocks, in particular, it is very rare that homogeneous rocks are distributed uniformly. In general, geological conditions are distributed in a wide variety, ranging from earth, sand, soft and medium rocks to hard rocks. Under these geological conditions, when planning of the tunnel construction is to be made out, either blasting method or tunnel boring machines must be selected taking into consideration the geological structures along with the designed tunnel route,' possibility of encountering aquifers, hardness of rocks anticipated and also, the adjacent environ- mental conditions. In the process of select- ing an excavation method,, it is important to make a comparative investigation between the above two methods considering the advantages and disadvantages with regard to the respective operating efficiency, economical efficiency and the conditions and scope of application as well. Furthermore, in addition to these considerations, the recent environmental restriction, which does not allow the blasting in the surroundings of residential areas, must also be taken into account. Because of this, in some cases there is no alternative but to use a static excavation method or a tunneling machine even when these are less efficient than blasting.

Jan 1, 1987

By K Hobbs

Mining is experiencing a difficult period of low profitability and declining productivity. To achieve sustainability, mining companies are challenged with improving output, quality and safety while decreasing costs. At the same time, organisations are having to manage a workforce in which individuals no longer accept a traditional style of management, employees prefer more flexible employment, and diversity within teams is becoming the expected norm.Increasing organisational diversity has been shown to have a positive impact on performance and therefore sustainability. Gender diversity and equality between working men and women is the area most studied in this regard. Executives are becoming more aware of the correlation between gender diversity and performance with some larger organisations having dedicated resources to increase the number and status of women in their organisations. Despite this, limited improvement in gender equality is apparent globally over the last decade with some industries, including mining, going backwards. So why is this the case and what other strategies are available?In 2015, the United Nations Women National Committee Australia (UN Women NCA) in conjunction with Autopia released a white paper discussing the lack of visible change in gender equality despite the widespread implementation of merit-based personnel management strategies. Using research from around the world and thoughts from influential government, education and business leaders, the paper ‘Rethinking Merit’ debunks the myth of the meritocracy. It provides a number of recommendations for organisations committed to improving their performance and sustainability through diversity, including a variety of real-life company examples, instead of relying solely on merit-based decision-making.This paper takes the recommendations of ‘Rethinking Merit’ and applies them to the mining industry. It shows the relevance that rethinking merit has for the industry and why applying the recommendations can result in an increase in diversity, therefore enabling greater performance and sustainability of mining companies. This paper provides case studies from Aurizon, Iluka Resources and BHP Billiton and, as a guide for managers, a generic diversity strategy designed to be implemented alongside traditional merit-based personnel management techniques.CITATION:Hobbs, K, 2016. Rethinking merit for a sustainable mining industry, in Proceedings International Mine Management Conference, pp 139-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

The Rock Mass Rating (RMR) and Rock Mass Strength (RMS) classification systems for jointed rock masses are briefly reviewed, with particular reference to their use in slope stability studies. A correlation is provided between the results obtained from the two classifications and an equation is presented tentatively defining the RMR value for long-term stable slope angles. The validity of the equation is discussed in general terms in the context of slope stability problems commonly encountered in Western Australian open pit gold mines.

Jan 1, 1992

By Bruce P, Luyendyk

The South Island of New Zealand comprises a collage of distinct tectonostratigraphic terranes. Some tectonic models predict that these terranes formed on or near the margin of Gondwanaland. However, geologic evidence suggests that some of these terranes may be exotic. Over 400 samples from 30 sites were collected from the Brookstreet terrane within the Takitimu Mountains. The section includes the early Permian Takitimu Group and the late Permian White Hill Intrusive Suite. Over 80% of the rocks show a partial or complete regnetization in the present field due to recent acquistion of VRM. Although some remagnetization of the Takitimu Group occurred during the emplacement of the White Hill Intrusives, both early and late Permian direction have been isolated. These directions indicate a mid-latitude origin for the Brookstreet terrane, and suggest a strong clockwise rotation between early and late Permian time. A published paleomagnetic result from the younger, but related, Murihiku terrane suggests that the Brookstreet terrane was sutured to the margin of Gondwanaland by the late Triassic, or that the Brookstreet and Murihiku are two distinct terranes.

Jan 1, 1987

By B J. Beven, A Vatandoost, J Young, S Campbell-Hardwick

The intrinsic value of iron ore depends on its physical and chemical characteristics. For example, silica and alumina are unwanted elements, downgrading iron grade and adversely affecting high temperature processing, attracting penalties in smelter contracts. For this reason, an informed knowledge of processing characteristics and product quality of the ore is valuable and cost effective during mine planning and processing.Ore variability is a significant factor that affects metallurgical behaviour and efficiency of ore processing equipment. Ore of sufficient chemical and physical quality needs to be modelled, mined, processed and usually blended. Feed and product assays are commonly used to assess potential ore upgradability. However, assays alone cannot be all informative of actual processing response given the variability of the physical properties of the ore.This study investigates the potential benefit of implementing a geometallurgical approach during the commissioning stage of the Kings deposit, part of the Solomon Iron Ore project in Western Australia. Kings drill hole database information, ie geological, textural and geochemical data, together with the results of metallurgical test work were used for geometallurgical analysis and modelling. Three main ore types were identified at Kings, namely channel iron deposit (CID), bedded iron deposits (BID) and Detrital Iron Deposit (DID). Additional classifications were utilised to better characterise these units in terms of their physical properties.Bulk sampling for each ore type was carried out across the deposit for metallurgical testing. Multivariate statistical models were developed for prediction of product quality for each geometallurgical unit. A new approach for modelling yield based on ore upgrade factors is introduced. These models were then applied to the Kings regularised mining model to assess product quality across the mining blocks and to plan product stockpiling and blending strategies.CITATION:Vatandoost, A, Beven, B J, Campbell-Hardwick, S and Young, J, 2013. A geometallurgical approach for iron ore product evaluation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By S Mitra, D O’Dea, N Barrett, T Honeyands, P Zulli

The steel industry continues to explore and demonstrate technologies that decrease its greenhouse gas emissions, especially in blast furnace ironmaking where alternate operating conditions will be required. As the furnace has been optimised over many years, it is approaching the minimum fuel rate possible with coke and Pulverised Coal Injection (PCI). Alternative operating conditions are therefore required to further decrease greenhouse gas emissions. Because of this, hydrogen has been proposed as a reducing agent in the blast furnace. Injection of hydrogen through the tuyeres was assessed using a comprehensive 2D blast furnace global model. The model was calibrated to a blast furnace operating with PCI as a base case and various approaches to hydrogen injection assessed, with a particular focus on displacing PCI. The maximum hydrogen injection rate of 19.5 kg H2 per tonne of hot metal was predicted, limited by decreases in the raceway adiabatic flame temperature and top gas temperature. Internal blast furnace conditions, such as gas composition and reduction degree were also predicted. Holistic analysis was performed to estimate the effectiveness of hydrogen injection on reduction of greenhouse gas emissions. Based on these results, the changes in blast furnace operation and emissions under hydrogen injection are discussed.

Nov 8, 2021