Search Documents

By Glastonbury J. R

The kinetics of the direct chlorination of, zircon in the presence of carbon was studied at temperatures between 9000C and 12000 C. From the experimental data it is prop- osed that the most likely mechanism for metal oxide (MeO2) chlorination is as follows: At I Surfaceon zMeO2+ZMeCl - MeOC12 (1) At Carbon MeOC12+C+Cl MeC14+CO (2) Surface It.is envisaged that this type of mechan- ism would occur for both the zirconium and, silicon. constituents of the ore. In the above mechanism; the surface re- actions appear to be fast and not rate controll- ing. In a carbon surface deficient bed the diff- usion of oxychloride intermediate through the boundary layer to the carbon surface becomes the rate controlling step. In a zircon surface deficient bed the diffusion of oxychloride away from the zircon surface controls the reaction. This postulated mechanism can be used to ex-, plain the observed experimental effects.

Jan 1, 1973

Facies associations in the Okiduse Volcanics, woodlark island, suggest that two major volcanic centres erupted synchronously during the Middle Miocene. These centres are referred to as the Watou Mountain Eruptive Centre and the Uvarakoi Caldera. The Watou Mountain Eruptive Centre, centred on Boganuse Mountain in the Okiduse Range, was a typical, moderate-sized composite volcano (or stratovolcano). The seq-uence is readily divisible into lava (Boganuse lava unit), breccia (Nikuben breccia unit) and epiclastic (Talpas sandstone unit) dominant facies, typical of composite volcanoes. These facies girdle Boganuse Mountain and they are interpreted to represent vent, cone forming and ring plain associat-ions, respectively. These facies indicate a reconstructed volcano of approximately 1,700m height with a basal diameter of 7km. The presence of limited exposures of intrusive associated with the vent facies (Kuike'beimmicrodiorite) suggests that the volcano is only partially dissected. The Uvarakoi Caldera is a felsic volcanic system contrasting with the mafic Watou Mountain centre.

Jan 1, 1994

By Gelding P. W, van Herk H

The Cattlegrid copper orebody is a concealed thin, tabular sheet localised near an unconformity between two sub- horizontal Precambrian sandstone units. It extends over an area of 1,000 m by 500 m within a wider area of mineral- isation. The ore consists of complex sulphides and is neither massive nor disseminated. It consists mainly of irregular fillings in pore space developed between clasts in sandstone breccias, in fault zones and joints and along stratification planes. Its habit is unique amongst Australian base metal ore bodies. During the pre-development period ore was outlined by percussion holes but in studies leading to investment decisions ore reserves were manually calculated from intercepts and assay results of cores from diamond drill holes. The methods used for estimating reserves in the pre-production and production periods are described and evaluated by comparing mine production during the first five ore production years with the forecasts made.

Jan 1, 1979

By Pollard D. M

In the batch phase disengagement test, an organic and an aqueous phase are mixed together for a known period to produce a dispersion which may be either organic continuous (aqueous phase droplets) or aqueous continuous (organic phase droplets). The continuity of the dis- persion will depend upon the method of init- iating the dispersion, the conditions under which the system is operating, such as temper- ature and impeller speed, and the properties of the liquids, such as viscosity, inter- facial tension and solute content. Once the dispersion has been agitated for the required period, the agitator is turned off and the position of the coalescence interface and the sedimentation interface recorded as a function of time. This will produce a plot similar to Figure 1, where the overall dir- ection of travel of the droplets of dispersed phase is away from the sedimentation inter- face and towards the coalescence interface where the droplets coalesce with the homophase.

Jan 1, 1987

Two examples of risk assessment and risk management in action are discussed. The first is in a management context in relation to Kingsgate Consolidated LtdÆs Chatree operation in Thailand. Kingsgate has conducted an over-riding risk management program to assess and manage risk across its complete business from the Sydney and Bangkok offices through to the Chatree Mine and the companyÆs exploration group. This example addresses how Kingsgate has applied risk management, particularly to the process operation, and the benefits that have been gained. The second is in an operational context in relation to Minara Resources LtdÆs Murrin Murrin operation in Western Australia. The subject is the methodology and outcomes of a risk assessment across the Murrin Murrin operation specifically to identify and assess risks with potential impacts from $1 M to $7 M. This section of the paper then shows how the outcomes of the risk assessment were integrated into MinaraÆs strategic plan to debottleneck the plant and increase nickel production.

Jan 1, 2004

By Williams ID

Ore and coke of various size fractions (1 to 11 mm) were packed in a column (146 ó) and resistance to air flow measured under a range of conditions. Results have shown that layered charging results in an interface having essentially a directional structure the thickness of which is directly proportional to the coke and ore size ratio and whose flow resistance exceeds that of the coke layer many times its thickness. Friction factor - Reynolds number plots showed large positive departure from the Ergun equation for all components investigated whilst functional analysis and that in terms of bed constants, showed a strong dependency of the pressure gradient on bed properties and the actual particle size as well as the size ratio. It is also shown that pressure gradient in mixed beds follows previously reported behaviour and that a directional interface offers higher resistance to flow than a mixed interface having the same volumetric ore/coke ratio. Significance of results to practice is discussed.

Jan 1, 1975

By Grinbaum B, Stevens G. W, Dalton R. F

Many hydrometallurgical processes produce large amounts of acid waste. This is illustrated by the copper S/X-E/W process which produces a bleed from the electrolysis tank house in the form of a concentrated sulphuric acid stream. Currently, the bleed stream is necessary to remove impurities such as iron that decreases the efficiency of the electrowinning process. However, this comes at a high financial cost owing to large quantities of make-up sulphuric acid required. A process has thus been developed with Zeneca Specialties (UK), ICI Australia and Gunpowder Copper Co at the University of Melbourne for the recovery of sulphuric acid from copper tank house bleed liquor. The recovery process uses the method of solvent extraction. Solvent extraction has the advantage of being a well-established technology in the mining industry and will reduce the environmental impact of the S/X-E/W process, as all additional chemicals can be completely recycled. A simplified diagram of the process is shown in Figure 1. Tank House

Jan 1, 1997

The Western Australian Mining and Petroleum Research Institute (WAMPRI) was established in 1981 by the Western Australian Government as a funding and co-ordinating Institute to foster research into the mining and petroleum industry within this State. To June 1984, the Institute has sponsored 34 projects with a total notional value of $2.5 million and an actual cash commitment of $1.5 million. Strong support for WAMPRI has come from Industry with 60 companies contributing half the money needed for the research grants.The 34 WAMPRI projects funded so far cover all aspects of the mining and petroleum geosciences.Several WAMPRI projects are concerned with gold including processing technology and the development of exploration models and techniques, they are providing successful results.Although well supported by Industry there is a surprising lack of applications being submitted to the Institute in the area of mining engineering, where it is felt there is much scope for research projects.

Jan 1, 1984

By Q-c Li, G-l Gao

Cyanided tailings produced by gold processing operations may cause environmental problems, because they contain pollutants such as arsenic, sulfur and cyanide compounds. Moreover, tailings containing economic metals such as Au, Ag, Cu, Pb and Zn, are potentially valuable resources. In this article, cyanided tailings are catalytically oxidised by nitric acid in the presence of air or oxygen. The resulting solids may be leached to recover Au and Ag. The solution can be used to prepare ferric sulfate or iron pigment. Gases released in the reactions were recycled and reused by oxidation and absorption. All of these greatly improve metal recovery and the reuse prospects of cyanided tailings. Under the following conditions where the initial temperature of oxidation is 80¦C; initial concentration of nitric acid is 30 per cent (by weight); feed proportion (nitric acid to cyanide tailings mass ratio) is 3:1 and reaction time is two hours, the conversion ratio of cyanided tailings is 90.06 per cent. At the same time pyrite in the cyanided tailings is oxidised effectively, gold recovery is as high as 92.3 per cent and nitric acid loss per cycle is only five per cent because of NOx recovery.

Jan 1, 2007

INDEX OF CONTENTSIntroductionChemical compositionsNormally Cooled MattesPort Kembla mattesMount Lyell matteMount Morgan matteGranulated MattesConclusionsIllustrationsINTRODUCTIONIn a previous paper in these Proceedings(l) an account was given of the composition of some copper-lead mattes from the Port Pirie Smelters. The research programme of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research organization has since been extended to copper-iron mattes from Port Kembla (The Electrolytic Refining ana Smelting Co. of Australia), Mount Lyell (The Mount Lyell Mining and Railway Co.) and Mouilt Morgan (Mount Morga:p. Ltd.).Chemical Composition of the Mattes.The mattes examined have a considerable range in chemical composition, as is shown by their analyses (Table 1).

Jan 1, 1949

By Artone E

screening equipment installed in e Hamersley Iron operation is described, and tails of operating parameters and screening - Iia in use are given. Tests were carried out on full-size reens in the operating plants to study the Meets of mat aperture size, feed size distri 1,ution, feed rate, screen speed and throw, angle of inclination, and feed moisture content n screen performance. Sampling equipment was signed so that undersize samples could be htained from various locations along the length of the screen, thus providing information pout the quantity and size of particles passing òhro gh the screen at any point. Conclusions derived from the testwork and relevance of these to the Hamersley Iron aeration are discussed.

Jan 1, 1984

Integrated geological interpretation of aerial photographs and Landsat images revealed that the gold mineralisation at Kyauk Pahto took place in a narrow zone of tension fractures within part of a previously unrecognised dextral wrench fault system. The latter is the wider manifestation of the well known Sagaing (right-lateral) strike-slip fault which has a length of more than 1 000 km, and it demarcates the boundary between the Indo-Australian and Asian plates. A subtle, right-handed kink affects the full width of the Sagaing Wrench-fault System at about the latitude of Kyauk pahto, and the extra dilatancy imposed on the tension fracture zone facilitated episodic ingress of mineralising hydrothermal fluids by "seismic pumping".

Jan 1, 1987

South Crofty's ventilation network is large and complex. Of the total exhaust air quantity 40% enters the mine by leakage routes through old workings, this air carries high concentrations of radon gas and results in the mine becoming a classified work place under the Ionising Radiation Regulations 1985. Improvements in the control of the ventilating air and dilution by increased air quantity have reduced the average contamination to aelow-0.2 WL. The major part of the radon originates from ground water inflows and from concentrations of radium within the mine with direct emanation from rock surfaces being negligible. Of 600 kBgs-1 total radon leaving the mine 93% cannot be accounted for from known and accessible sources.

Jan 1, 1988

The gold deposits of Kalgoorlie are the most important on the Precambrian shield of Australia. Gold was first discovered.'-:.V. ,,.,.-,..Kalgoorlie in June, 1893, and olthough`the original find was of ;:...;;small extent, the prospecting activity which stemmed from it 'led to'the ciscovery.of the lodes of the Golden Mile, some three miles to the south. Th¬ production of thea1algoorlie fiold.a.t December 31st, 1962 was 80,556,572 tons -for -33.,853, 215 ounces of gold. Most of this production has come from the Golden Mile area anu Table 1 summarises the Gplueh Mile. production for periods which correspond approximately to the main phases of operation of the field.

Jan 1, 1964

By Chilman G. F, Lean P. J

The New Broken Hill Oonsolidated LImited (NBHC) concentrator was commissioned in 1952 and underwent a number of expansions over the next 25 years. In 1978, the decision was taken to expand further from 1.20 million tonne/yr to 1.43 million tonne/yr. This increase necessitated a substantial modification to an already over-taxed grinding circuit. The circuit consisted of rod mills, ball mills and rake classifiers. Plant data of grinding mill performance was obtained to develop mathematical models of individual units that could be combined to simulate total circuit performance in a number of configurations. The data provided further illustration of the validity of the perfect mixing model for relatively small increments of ball mill scale-up.

Jan 1, 1983

By M.E. Crump

Gallium occurs at above background levels in most samples collected from 11 of the major geothermal areas in the Taupo Volcanic Zone. Concentrations of Ga in the 48 samples ranged from 8 to 144 mg kg-' and varies widely from place to place within each geothermal area. Gallium is contained within the alumino-silicate structure of clay in the mud, having substituted mainly for Al. Suggested deposition mechanisms for Ga also involve co-precipitation with Sb, As, and SiO. colloids. Digestion trials, carried out to determine extraction conditions for possible commercial exploitation, showed that heating the mud to 500 -600¦C for 1 hour followed by acid/alkali treatment gave complete recoveries.

Jan 1, 1995

The process of hydraulic transport through pipelines, world-wide well known for the trans- port of fine-grain solids is also being used to a greater extent in mining for the handling of 1rimarily coarse-grain solid - water mixtures r the removal of, for instance Coal and waste mixtures after coal winning rising hydraulic monitors, lings for backfilling underground and :her tailings and flotation waste to A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining P',search Company) in Essen-Kray, GFR, to ¦urther improve this technology. The unit was :fanned and built by Krupp Industrie- and +hibau of Duisburg in cooperation with i r

Jan 1, 1980

By Tuite M. J, Woolcock L. J

The Awak Mas gold project is located in the Province of South Sulawesi, Republic of Indonesia. It is situated 300 km by road north of the provincial capital of Ujung Pandang. The capital is readily accessible by air from Australia via Denpasar on Bali or the Indonesian capital, Jakarta (Figure 1). Elevations at Awak Mas range from 850 to 1400 metres above sea level in reasonably rugged terrain. The area is covered by primary and secondary (regrowth) rain forest. The region is subject to an equatorial-type tropical climate. The annual rainfall is a high 3000 mm most of which falls in the rainy season between March and June. In the lower valleys rice, cloves and chocolate crops are cultivated. Title to the project area is secured by a Contract of Work (COW) issued to PT Masmindo Eka Sakti (MES) on 23 October 1987 by the Government of Indonesia. MES was controlled at the time by New Hope Industries group of Brisbane. After New Hope had completed initial reconnaissance exploration of the area, Battle Mountain Gold Company (BMGC) farmed-in in 1991 and earned a 60 per cent beneficial interest in MES.

Jan 1, 1996

By M Ujihira, M Komazaki, K Higuchi, D F

A diesel engine with a misfiring cylinder is likely to break down in a short time when the engine is used without maintenance. The authors have developed a method of detecting the occurrence of cylinder misfiring and specifying the misfiring cylinder by using wavelet analysis and statistical analysis on the root mean square (r.m.s.) values of two kinds of acceleration waveforms. This detection method is considered superior to traditional methods, which require several accelerometers, especially in terms of simplicity. Since the development of the method, research has been conducted on semi-automatic processing of measured signals and signal transmission from the worksite to a remote office. Field tests confirmed that 1 + 105 points of dynamic data could be transmitted through the mobile multimedia network within 15 minutes, and the time for signal processing was within 15 minutes. Final determination on the condition of a diesel engine in heavy machinery could be achieved within 30 minutes. Shortened processing time is expected by improvement of the processing software.

Jan 1, 2003

By Borgelt B. V, Perry A. J, Wellington H. K

There has been little change in the lead smelting practice at Mount Isa since 1939 when the metallurgy and general practice were outline by Raney and Blott.The purpose of this paper is to descriqe some of the operational details that have influenced the overall production. The slag fall hns been increased by the lowering of the lead content of the concentrate. Further, as it is the practice to include iron on the furnace charge and carry a higher lime content in the slag, both factors have produced notable results in furnace operations.All blast furnace gases are filtered in a baghouse and this unit is. being further extended to take all smelter gases, thus eliminating the existing Cottrell plant handling Dwight-Lloyd gases.The lead smelter was closed down from April 1943, to May 1946, during which time blister copper was produced.The report is subdivided as follows:-1. Filtering and Mixinga. Effect of calcium sulphate on cloth.b. Dwight-Lloyd charge composition.c. Main mixer.d. Return sintel sizing.2. Blast Furnace Operationsa. Introduction.b. Use of orehearth.

Jan 1, 1953