Search Documents

The scope of this paper has been restricted to the manufacture in Australia of seamless steel tubing, as the subject of buttweld tubing has already been dealt with by A. N. Hamilton in a paper delivered before the Institute in 1935.The earliest attempts to produce seamless steel tubes were based on the extrusion of lead piping, a process developed by Thomas Burr in 1820. However, the problems associated with the extrusion of white hot steel had to await the metallurgical knowledge of the twentieth century, and these early attempts were unsuccessful.The years 1840 and 1845 were noteworthy for the introduction of the first practical methods of making seamless steel tubes. In one process, a large circular plate was 'cupped' in a vertical press; in the other, a round steel billet was pierced for its entire length.The product from both these methods was then elongated by repeated reheating and rolling over an internal mandrel, in a circular pass mill.At this juncture, it should be noted that every process developed for the manufacture of seamless steel tubing can be divided into two parts. In the first part of the process, attention is centred on the conversion of the heated bloom into a short, thick-walled, hollow cylindrical forging; this product is then elongated in the second section of the process. It will be noted that these two sections are actually quite distinct, and in practice numerous methods exist for carrying out both functions. The first stage is generally referred to as 'piercing', the second stage being termed 'elongating.' In this paper, the author proposes to outline the various methods adopted for piercing and elongating; the reader is asked to note that although certain methods of piercing are almost invariably associated with only one method of elongating, the distinction between the two functions is, nevertheless, a vital one and should be noted accordingly.

Jan 1, 1947

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2008

By Huafu L, Ruishi N, Hongnian Y, Qinglong Z, Yangshen S

The Dongshan terrane was first recognized in 1984 (Guo,et al., 1984, 1989) as an old continental crust block of migmatized granitic gneiss in the Southeast Coastal Hercynian-Indosinian orogen, and it was thought to have occured on Dongshan Island, which has an area of less than 100 km? Recent research work has shed much light on the geology of the Dongshan terrane.The Dongshan terrane is approximately 40-50 km wide and 380 km long, trending NE. It runs from the region of the mouth of the Ming River through Putian and Huian Counties, Amoy and Dongshan island of Fujian Province to Nanao island of Guangdong Province, bordering the southern segment of the coastal region and coastal islands of Fujian and eastern tip of Guangdong Province. The Dongshan terrane is divided from the Zhejian-Fujian Mesozoic Volcanic Mountain Chains by the Changle-Shaoan fractural zone, and its eastern boundary is covered under water in the Taiwan Straits.

Jan 1, 1990

By Cole RT

The cultural ages of man have been defined in terms of smelting and hence as a prerequisite, mining for example the iron age and the bronze age. There could be no separation of the man from his role as the technologist (miner/ smelter) for his early metal working efforts were to enhance survival. In the millenniums since, the artisan specialist developed and the technologist emerged. The process is a sort of technical natural selection. From the generalist hunter, gatherer, miner, metalworker we advanced over the centuries with great 'steps for mankind' to the series of specialists each largely intent on securing his/her technical functions from the curious assaults of other tribal members. The relevance of all this to the theme, 'Past, present and future of the Victorian mining and metallurgical industries', is simply that people have always, and will always, be the moving force in our industries. It is the effectiveness of people now and in the future that this paper addresses.

Jan 1, 1982

By R Gaze, J Horton

Block models generated with all linear interpolation algorithms contain inherent smoothing that typically results in an underestimation of grades and overestimation of tonnes in resource estimates. For mineral deposits that are anticipated to be exploited by underground mining methods excessive smoothing may result in materially misleading estimates of Ore Reserves. To account for smoothing in the open pit mining environment recoverable reserve techniques such as indicator kriging and uniform conditioning are employed to provide non-spatially located proportions of the large blocks above the cut-off grade. These models are not suitable for underground mine planning where the actual location of material above cut-off is required to design its extraction. To correct for excessive smoothing it is proposed to modify the ordinary kriged block estimates a posteriori using an affine correction with a local variance adjustment factor. The proposed methodology is demonstrated for a base metal deposit during a feasibility study.

Jan 1, 2009

Plenary Address Zinc is a trace element in all igneous rocks and its background geological occurrence roughly follows iron but at much lower concentration. Living matter reflects this abundance and zinc is an essential trace element for complex life forms. Thus, environmental issues include zinc deficiency in soils and/or water - and thus in local diets - and zinc toxicity evident in natural or modified ecosystems. Increased knowledge of the role of zinc in plant and animal metabolism emphasises the need to manage, within guidelines based on naturally occurring abundances, the concentrations of zinc in water, spils and in the food chain. Although recognition of the natural variability of zinc concentration provides some basis against which environmental protection standards might be set, the measure of environmental `pollution' is more commonly taken as the degree of change to natural, background levels, attributed to the particular land or water use activity. Environmental constraints on mining, processing and usages of zinc may have less to do with actual

Jan 1, 1993

It is self evident that in many cases mining disrupts communities, however, community reaction to mining varies enormously. This is due to a whole host of factors, some physical, some financial, some political and some a direct result of the projected mining company attitude towards the community at large. Physical and political factors are increasingly being dealt with realistically and financial aspects are to a significant extent determined by profit margins. If the acceptable profit margin canÆt accommodate all necessary costs (which now includes a variety of community considerations unheard of even a decade ago), then the project is just not viable. Despite major commitments now made by many mining companies to their affected communities, corporate attitudes, and their projection, remain as the most outstanding factor in mining project development where real gains can still be made in effectively reducing social risk. This paper addresses both international and domestic experience gained in managing this aspect of mining development risk, including initiatives implemented by multilateral institutions.

Jan 1, 2003

It has long been recognised that applications of the Net Present Value (NPV) investment decision making methodology can have serious deficiencies in situations where investment can be delayed and, once made, various options allow increases or decreases in the level of output. NPV valuation can undervalue the project if it does not incorporate future flexibilities or ""options"". It is important to realise that a proper valuation of a project (ie, valuation of its future cash flows) must incorporate an analysis of optimal future decisions involved in managing the project. Current valuation cannot be divorced from a consideration of future decision making. There is now a considerable amount of literature, mainly academic, identifying and exploring ways of remedying these deficiencies in the application of NPV. While the necessity of period by period analysis is sometimes acknowledged, little if any practical illustrative model building has been published to date, aside from algorithms using continuous time stochastic processes which deny access to the uninitiated.

Jan 1, 1994

By Sudharto RT

Sulphides of Cu, Pb, and Zn occur in quartz veins associated with a quartz monzodiorite stock at Gunung Limbung, West Java. The mineralization was polyphase and occurred at depths of less than lkm. Wall- rock alteration is extensive and typically consists of an outer zone of propylitization and an inner zone of potassic (K-feldspar- rich) alteration. Sporadic argillic altera- tion is probably of supergene origin. A variety of elements were mobilised during hydrothermal alteration and Ba in particular shows mared enrichments in the potassic zone. Fluid inclusions in the vein quartz indicate that temperatures of mineralization were within the range 250-3900C and that two fluids with differing chemistry were involved. One fluid had high Ca/Na ratios and a low overall salinity, the other had low Ca/Na ratios and a moderate salinity. The former is probably of meteoric derivation, whilst the latter had a magmatic origin. Precipitation of the sulphides was probably brought about by mixing of these fluids.

Jan 1, 1987

Government geoscience may be categorised by objective under three headings: Applied Research for Geoscientific Framework Studies, Resource Inventory, and Technical Advice. In Queensland, the Department of Resource Industries is active in all three categories. Under the program-based management system adopted in 1987, three Programs, namely, Geological Survey, Mineral Resources Development, and Energy Resources Development and Utilisation, have geoscience responsibilities.Prime responsibility for geoscience resides with the Geological Survey Program, which provides a geoscientific framework for mineral and energy exploration and the development of the State. Simply stated, the Program goal is to provide geological information when and where it is required. Geological Survey work also encompasses aspects of resource inventory and technical advice, complementing the work of the other two Programs. This role has a 122 year long tradition, for geoscientists of the Geological Survey have been engaged in investigations designed to facilitate the identification and utilisation of the mineral, water and energy resources of Queensland since 1868.

Jan 1, 1990

By Morrison RD, Simmons CJ

A bewildering array of process control instrumentation is currently available for mineral processing plants. For sequencing control, special purpose microprocessors or the process control computer can be used. Where continuous control is required, then the choice is between pneumatic controllers, electronic controllers, shared display micro- processor systems and direct digital control. The benefits of each system are discussed and the advantages of using direct digital control in mineral processing plants are outlined. The factors which need to be considered when selecting control systems for new plants are listed. Instrumentation systems designed by Fluor Australia are used as case studies to illustrate the selection process. For established plants, conversion to direct digital can be advantageous, and case studies are given. However, replacement of existing systems requires justification based on a productivity improvement which will allow the control equipment to be paid for within a specific time period. Productivity improve- ments maybe assessed in terms of increased

Jan 1, 1978

By A Quigley

The Northside Storage Tunnel Project in Sydney includes over 20 km of TBM driven tunnels, over 3 km of declines and major caverns and pump rooms. The paper describes methods used for design on the project. Emphasis is given to the refinement of the use of empirical rock mass classifications, and to the use of discontinuum numerical methods.The use of empirical rock mass classifications in Sydney sandstone has usually led to conservative design because the systems are based on a random orientation of joints in the rockmass. Because the joint sets are usually oriented in a way that is beneficial for tunnelling, limits must be placed on the parameters used in the classifications system. The paper discusses these limits and the derivation of the parameters.The use of numerical methods in Sydney sandstone is discussed. Continuum methods have their uses, but discontinuum methods are preferred. The use of UDEC has been validated against a previous project, the New Southern Railway. Recommendations are given for UDEC models.

Jan 1, 1999

In the humid, subtropical climatic conditions, typical of Papua New Guinean high-lands, auriferous carbonate-quartz lodes and stockwork veins of the Upper Ridges mine at Wau, have weathered in situ forming manganese dioxide-quartz wad flatmakes and veins. Vein assemblages and sulphidized host breccia have been chemically weathered to 20-25m depth, and microscopic grains of electrum (550-600 fine) formerly enclosed in carbonate, sulphide and quartz have dissolved in the oxidizing alkaline fluid. Coarse secondary electrum, crystalline and dendritic, is concentrated by manganese dioxide and at the base of chemical weathering. Fineness is unchanged, eliminating the possibility of gold and silver migration as a chloride complex. Experimental tests on the stability of thiosulphate, and its ability to dissolve gold and silver from colloid, crystal and synthetic alloy confirm that secondary electrum at Upper Ridges is most compatible with precipitation from (Au,Ag)(S203)23-; a complex readily destabilized in the presence of MnO., or with decreasing Eh.

Jan 1, 1984

Proper technical appraisal of a coal deposit and the determination of optimum open- pit mine design can only be made after detailed examination of a number of interrelated geographical and geological factors. Initial evaluation of the geography and the overall attitude of the coal measures can often determine the most likely coal mining technique. Conclusions reached in the early stage of the investigations frequently dictate the quality and quantity of particular types of data required from further drilling of the deposit. In many cases, insufficient information relating to the overall engineering aspects of a coal deposit is derived from drilling. Little or no attention is paid in the exploratory phase to such things as the specific gravity of selected overburden samples, floor conditions, clay content of the overburden and selected strength tests on cores. This is a direct result of geologists treating coal deposits purely in geological terms without sufficient consideration being given to the engineering parameters required for a proper evaluation of the deposit.

Jan 1, 1977

The Permo-Triassic Bowen Basin developed during the final stages of the Tasman Orogenic Phase in eastern Australia. The basin has considerable economic value as a source of coal, natural gas and precious metals. The basin, which is of controversial origin, is preserved as a north-south trending, asymmetrical syncline bounded in places by faults. It is here interpreted as a retroarc foreland basin which developed on the landward (west) side of a continental arc associated with continent-ocean plate convergence. Initiation of the basin occurred via back-arc extension in Early Permian times, coincident with a phase of talc-alkaline arc volcanism. Early Permian, mostly marine sedimentation gave away to extensive coastal and alluvial plain depositional systems in Late Permian times, coincident with a resurgence of arc volcanism. Triassic sedimentation was almost entirely alluvial and coeval with westward propagation of thrust sheets from the eastern basin margin. Compressive tectonics climaxed in Middle to Late Triassic times, terminating sediment accumulation and uplifting the entire area.

Jan 1, 1990

By Williams SR

Column Flotation cannot be used indiscriminately. Based on extensive pilot plant experience at Lakefield Research, a number of limiting parameters have been identified for the application of column cell flotation. Parameters of importance are the use of wash water, flotable mineral content, pulp viscosity, type of mineral selectivity being sodght and degree of mineral liberation. The paper discusses when wash water should be used and the positioning of a column within the circuit as this is important to maintain a sound water balance for the circuit and prevent excessive circulating loads. Other areas of debate are pulp chemistry, very low and high weight recovery, for which the conventional column is a poor selection of equipment, and treatment of complex ores, where the separation of valuable minerals is more difficult than non-sulphide, sulphide mineral separation. Based on these observations, the application of column flotation must be carefully considered or can be optimised.

Jan 1, 1993

Nickel ores from three different mines, Digger Rocks, Cosmic Boy and Flying Fox, are treated at the Forrestania concentration plant. The ore types vary from oxidised supergene ores to primary pyrrhotite+pentlandite ores. Mineralogical investigations on the ore and process samples have been carried out in different stages of process development. One of the studies was done with the samples collected from the flotation circuit in 19 June 1994 when the Cosmic Boy ore was processed. The process products were screened, and the size fractions were analysed for the main elements by appropriate analytical methods. Mineralogy of the products was studied microscopically and composition of the sulphides was analysed with an electron microprobe. Liberation of the main sulphides in the flotation feed was determined with the point-counting method, and weight percentages of the minerals were calculated using chemical and mineralogical data. The typical sulphide assemblage of the Cosmic Boy ore is violarite, pentlandite, pyrite, pyrrhotite and chalcopyrite. Violarite dominates over pentlandite (ratio being 70 per cent to 30 per cent), and pyrrhotite is strongly replaced with pyrite and magnetite. One of the most common mineralogical features of this ore type is secondary magnetite, which occurs as narrow rims in porous violarite or in association with secondary pyrite. Serpentine, talc and chlorite are the main gangue minerals. In the milled feed (76 per cent -74 ¦m) locked particles between nickel and iron sulphides are common. About 41 per cent of total pentlandite occurs as pure liberated particles, and 33 per cent as locked grains with violarite. Liberation degree of violarite is 55 per cent, and the most common type of locked particles is violarite+magnetite, carrying about 20 per cent of total violarite. To achieve a recovery of 80 per cent for pentlandite, all the particles containing at least 50 vol-% pentlandite should be floated into the nickel concentrate. Correspondingly recovery of 80 per cent can be reached for violarite if all the particles containing at least 65 vol-% violarite are floated.

Jan 1, 1996

By J Barnes

During September 2000, Nabalco management identified the need for a corporate system to deliver its key performance indicators (KPIs). In June 2001, a need was also identified to replace the existing metallurgical accounting system. After a review of the technologies available, the decision was made to develop the systems in-house, in preference to purchasing commercial software packages. This would allow much greater control over the structure, and provide for an iterative, concurrent development process between software and key business developers. This has proven invaluable in the development process. The purpose of the KPI system is to provide a unified reporting tool for all performance indicators. These indicators include production, safety, health and environment, personnel, costs, continuous improvement initiatives and opportunity losses. All of these disparate measurements are brought together into the KPI system and used to determine the performance for each department or area. The general principles of the balanced scorecard business approach (Kaplan and Norton, 1996) are applied to achieve a performance measurement for each area within Nabalco. The new metallurgical accounting system (MA) is a SQLServer database with web page and Excel interfaces. The database is structured around daily inputs of all measurements and calculations. The data is stored and adjustments and reconciliations can be made to this data as required. The focus is on accounting rigour, with all adjustments recorded in the database to allow for full auditing. The structure of the data focuses on the five input/output streams (bauxite in, caustic soda in, fuel oil in, residue out, and alumina out). In-circuit inventory provides a secondary measurement on which to check and calibrate the MA system. The KPI and MA systems were developed using Web technologies and are available to any internet-enabled device with Internet Explorer installed. This removes the need for software rollouts and user training. This will promote the wide use of the systems throughout Nabalco and Alcan.

Jan 1, 2002

By Walker BV

Mining activity has been an integral component in the New Zealand economy since the early days of European settlement. Recently in common with other Pacific Rim countries there has been a resurgence of investment in gold. A sustained and increasing exploration effort has resulted in the rapid development of alluvial gold mining operations, a number of hard rock gold discoveries, and a general optimism about New Zealand's prospectivity. New Zealand's attitude to mining development, in particular hard rock gold mining is influenced by high environmental values and a concern, largely through absence of examples, that modern mining may not perform to community standards. While these environmental concerns are wide spread there is a growing realisation that gold mining, if properly managed, can take place within acceptable environmental standards and that it has the potential to contribute significantly to New Zealand's economy. New mining developments have an important role to play in this process. The mining industry in New Zealand is now at a crossroads. Having invested substantially and confirmed the potential for gold mining developments it has found itself in a rapidly changing economic environment as the Labour Government puts in place a number of fundamental economic reforms. The reforms are intended to free up the economy removing the rafts of subsidies and protective measures which have stultified initiative and growth. A fundamental reform of the public service has been initiated including corporatisation of trading activities and the establishment of a Department of Conservation to administer estensive areas of Crown land. Both petroleum and mining taxation are being reviewed with the intention of creating a more neutral competitive environment. Mining legislation is also being re-examined with both efficiency and equity objectives. While the current environment is characterised by uncertainty and rapid change, the outcome will be a more market-oriented stable policy environment, to the mutual benefit of the industry itself and the New Zealand Community.

Jan 1, 1987

By Mingmin Dou

The behaviour and deportment of indium during the precipitation of sodium jarosite from Fe2(S04)3 - Na2SO4 solutions were investigated. Indium is readily precipitated with sodium jarosite, and the extent of In precipitation increases as the In concentration of the solution increases. It was shown that In 3+ substitutes for Fe 3+ in the jarosite structure to form a nearly ideal solid solution series. On a molar basis, the precipitation of Fe is slightly favoured over that of In, and the difference is reduced as the pH increases. Sodium jarosite precipitation becomes kinetically rapid at temperatures >70¦C, but increasing temperatures in the range 70 to 150¦C affect neither the relative precipitation of In and Fe nor the composition of the jarosite product. Low Na2SO4 concentrations result in reduced product yields and jarosite precipitates in which H3O' > Na+. The hydronium-rich precipitates have reduced In contents. Increasing the ZnSO4 concentration of the solution slightly increases the quantity of jarosite formed and results in the incorporation of -0.3 per cent Zn in the jarosite structure. Otherwise, the presence of ZnSO4 has no significant effect on the composition of the jarosite. Seeding accelerates the rate of jarosite precipitation but has a negligible influence on the deportment of In. The jarosite precipitation reaction at 98¦C is relatively rapid and near-steady state conditions are achieved in - 6 h even in the absence of seed. The initially precipitated jarosite is slightly enriched in In with respect to Fe. The ferric ion concentration of the solution has a significant influence on both the amount of jarosite formed and its composition. In particular, the jarosites precipitated from dilute Fe3+ media have significantly enhanced In contents. Hence, it may be possible to recover - 25 per cent of the dissolved In, at the 1000 mg/L level, in a jarosite precipitate assaying - ten per cent In by the controlled oxidation-precipitation of sodium jarosite from a ferrous sulphate processing solution.

Jan 1, 1993