Search Documents

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

By P Khalkho, M Singh

Rock masses when subjected to uniaxial or triaxial cyclic loading (eg in hydraulic running tunnels, during retrieval and injection of oil and gas from storage underground caverns and haulage roads), the material has a tendency to fail in fatigue. In order to design safe and reliable underground structures, the determination of brittleness under such loading conditions becomes a pre-requisite. Brittleness influences strongly the failure process and makes the rock mass behaviour complex under different tunnelling and mining activities. Brittleness Index is a term to quantify the brittleness feature of a specimen. In the present study, an attempt has been made to quantify the brittleness of jointed specimens using different brittleness criteria. The joints of the model jointed specimens were oriented at an angle of θ=15° normal to the loading direction, each having three different JRC’s=2–4, 12–14 and 14–16. The specimens were tested under triaxial conditions in incremental complete cyclic test scheme performed at displacement-controlled mode. Different brittleness criteria were used ie stress-strain dependent brittleness index, Young Modulus approach and energy-balance based mechanism. It was observed that energy-balance based mechanism which consider the post failure behaviour is more descriptive to reflect the whole variation of brittleness from sheer brittleness to ductility.

Nov 29, 2022

By M Nehring, M Kizil, P Knights

Mining and beneficiation can be described as sequential processes of separation of valuable minerals from waste. There is a great deal of interest in how the industry can be more effective – and efficient – with these processes. In particular, many mining companies are looking towards digital technologies to improve precision mining practices; that is, the targeted identification and separation of valuable ore from waste during the mining process. Greater precision will help unlock the value in many complex orebodies that are currently considered Tier 2 or 3 deposits. CITATION: Knights, P, Kizil, M and Nehring, M, 2018. Selection of precision surface mining methods for complex metalliferous orebodies, in Proceedings Complex Orebodies Conference 2018, pp 31–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A E. C Peres, P R. M Viana

The role of flotation columns in comparison with conventional mechanical flotation cells is discussed under the scenario of Brazilian flotation technology. All iron ore concentrator circuits commissioned since 1990 incorporated column only flotation technology in rougher, cleaner, scavenger configuration. Columns were also added to existing circuits, especially at the cleaner stage. Columns were also incorporated to phosphate ore flotation circuits operating mechanical cells. In two phosphate concentrators, columns substituted for all mechanical cells. Columns perform the cleaning stage in a large sulfide copper concentrator, following rougher flotation in tank cells. Scavenger of the cleaner tailings is performed in tank cells at this plant. Other ores that are concentrated in flotation columns include graphite, talc, lead-zinc sulfide, and a zinc hydrometallurgical residue for silver recovery.

Jan 1, 2005

By A Geldenhuis, M Hagger, J Maree

Disposal of mine water is a worldwide problem occurring in the coal and gold as well in the metal ore mining areas. Since southern Africa is a (semi) arid region, mining effluents should be treated to qualities such that they can be used for agricultural purposes or that they can be discharged in river system. Studies have shown that partly treated acid mine water can be used for irrigation. A copper mine in Botswana plans to use 5 M/d of treated mine effluent for the irrigation of agricultural product. The results of this study showed that when applying the biological sulfate removal technology the produced sulfide precipitated the metals in the mine effluent, such as nickel, Zn and Mn, to metal sulfide (MeS).

Jan 1, 2003

By J-P Franzidis

Mill operators have traditionally been forced to rely on grade-recovery curves and overall flotation rate constants when analysing proposed improvements to plants. This has led to loss in money and time when a proposed change that showed potential in laboratory scale tests failed to show improvement in the plant. Frequently, this is a result of the operators being unable to gain insight into how and why the proposed change affected the flotation performance. This is due to the classical models not including any description of the subprocesses of flotation and their individual contribution to the overall flotation performance. A new flotation model has been developed as part of the AMIRA P9 project that separates the flotation process into subprocesses and includes the contribution of both the pulp phase and froth phase to the overall flotation recovery. It is not possible to determine the individual components of this new model on traditional pilot plants as they lack the required flexibility and scale. Therefore a new pilot plant has been developed known as the Floatability Characterisation Test Rig (FCTR) that has the flexibility and features required for the determination of the flotation subprocesses. The flexibility and features of the FCTR also make it an ideal tool for investigations into many different aspects of flotation research. These include the effect of reagents, grinding, and power on the flotation performance. This paper will describe the methodology for using the FCTR in these fields of research and highlights the advantages of using the FCTR over traditional methods.

Jan 1, 2000

By Y, Li Jianxiong, Hu Hua, Gu Desheng

After having briefed the technical and economical advantages of continuous mass mining in underground metal mines, the authors discuss the four stages of research and development of continuous mass mining in China. The four stages are: vibrating ore drawing in a stope, continuous mass mining in a stope continuous mass mining without rib pillars in an area and continuous mass mining in whole mine. The authors briefly review the research achievements of the first and the second stage; Combining the key national research project of the æNinth Five Year PlanÆ ù æThe experiment and research of continuous mass mining without rib pillarÆ, the authors introduce in detail the technological condition of mining, the design ideas of continuous mass mining, the design scheme of mining, the technology of mining. the equipment of mass mining, the chief research achievements and so on. The success of research of continuous mass mining without rib pillar indicates the arrival of the third stage of research. The introduction of continuous mass mining will promote the technology revolution of mining in China remarkably. The authors also point out that the development direction of continuous mass mining of the 21 century is continuous mass mining in whole mine, which is the fourth stage of research.

Jan 1, 2000

By T Galvin

Drilling and blasting at Westside Mine near Wallsend, NSW, has presented a challenge for Orica Explosives, Australia. The colliery produces 600 000 tonnes of steaming coal per year from two seams using surface mining techniques. Tapping into underlying coal will greatly improve the yield, but there are many issues which make this an enormous challenge. Hunter Valley Earthmoving engaged Orica Explosives to supply the explosives products and to provide much of the blasting expertise that is needed on the minesite. Hunter Valley Earthmoving and Orica Explosives have proven to be an outstanding, unified technical team on this project. The success of the team is based on good communication, progressive attitudes, extensive expertise in blast design and most importantly, care and accuracy in implementing the agreed upon designs.

Jan 1, 1999

Industrial minerals and rocks (alternat ively called non-metallic minerals) are those- which are economically important because of their desirable physical or chemical properties rather than their metal or energy content. They are divided into nine classes: structural, pig- ments, process aids, ceramics and refractories, chemical source minerals, abrasives, foundry minerals, gem stones, electrical minerals. Development of deposits is influenced by the dominance of marketing,by the required range of products, the-need for specialized process- ing, place value, and the transportation and distribution of high-bulk, low-cost commodities. Evaluation is different from that of base metals because of differences in geological occurrence, sampling methods, testing, treatment, placing a money-value on the material and the importance of export markets.

Jan 1, 1973

Mount Isa Mines Ltd. annually extracts 5.6 million tonnes of copper ore from the 1100 Orebody. All production is by longhole open stoping, with an increasing emphasis on pillar recovery. Drilling and blasting prac- tices have been modified to allow more efficient pillar extraction, with the evolution of a "core and shell" approach. Blast design occurs at the stope design stage, while individual blast preparation is based on detailed ring plans. A programme of blasting research involving surface and under- ground vibration monitoring and fragmentation assessment has been car- ried out in conjunction with production personnel. Drilling and blasting practice in the orebody must continue to evolve with continued research, to suit changing conditions and take advantage of new technology.

Jan 1, 1988

Mount Isa mine is the largest underground mine in Australia and is located 2,000 kilometres north-west of Brisbane. This mine has been in continuous operation since 1931 and in 1986/87 the silver/lead/zinc stream achieved the peak annual mining rate of 4.7 million tonnes. At present about fifteen different steeply dipping stratiform orebodies are being mined to maintain an annual production rate of around 3.0 million tonnes. Out of these, only two orebodies (2 & 5) are amenable to sub level open stoping (SLOS) type bulk mining methods. This year only 150,000 tonnes are scheduled from pillars and remnant areas but in future, more sources will be required to meet the budget production targets.

Jan 1, 1990

The advantages of coordinate geometry in design and construction of underground works are apparent for reasons of flexibility, security, computer operations, survey error analysis, and the use of numerical techniques for setting out and checking works. Integration with National or State survey systems is useful in the long term, both at design, construction and future works stage. Equipment and methods are available which permit "absolute" monitoring of structures and strata over long periods,to close toler- ances. This work can be carried out in the limiting urban environment. Rapid data acquisition by semi-automatic devices, or photogrammetry, utilizing electronic data processing is capital inten- sive, but provides more data than analogue surveys (i.e., setting out centre lines) and becomes more attractive with increased labour Costs.

Jan 1, 1976

By Burgess J

Present practice of lead-zinc flotation at North Broken Hill Limited is described and factors influencing plant objectives and performance discussed. Mineralogical examination of final flot- ation products showed mineral liberation to be 94T complete and size by size metal recovery tables indicated a need for finer grinding to improve lead and silver recovery, but coarser grinding to improve zinc recovery. A steady grinding circuit, at constant ball mill power and cyclone overflow pulp density, is found desirable for satisfactory flotation circuit operation because instabil- ity in the grinding circuit inevitably leads to flotation instability and as a consequence less than optimal flotation operation. Remov- al of the variable lead flotation middling product from the grinding circuit decreased grinding instability.

Jan 1, 1978

By Quast K. B, Newell R, Caterford J. H

The most common reason for gold-bearing deposits being refractory is the presence of sulphides; in many cases these interfering minerals contain arsenic, antimony, or other environmentally-sensitive elements. A number of processes have been proposed or developed for pre-oxidation of interfering minerals. In most cases developers have focussed on gold recovery and capital costs, with relatively little data on the deportment or form of these potentially harmful elements. This paper surveys recent work connected with pressure pre-oxidation processes. Data from pilot plant treatment of refractory gold materials, using the nitric acid Redox process, is discussed along with the attendant flowsheet and engineering implications. Four refractory gold-bearing materials have also been tested at the University of South Australia for arsenic and antimony deportments.

Jan 1, 1991

A numerical model of the spontaneous combustion of coal has been developed and is being used to investigate the nature of self-heating in underground coal mines. Results to date confirm the complexity of the self-heating reaction in coal and illustrate the impact of the factors such as the coal reactivity, mass and airflow through the coal pile. Subtle differences in the chemical, physical and environmental conditions and make a significant difference in the development of a high temperature self-heating or a low temperature benign condition, the subtlety escaping normal underground observations. Additional work is planned to investigate the thresholds for such factors in the development of spontaneous combustion and it the implications for detection by gaseous Products.

Jan 1, 1998

By H Nikraz, E Jamieson, D Cooling

The use of red sand as fine aggregate in concrete manufacture has been investigated as well as the use of fly ash as a cement replacement. The experimental work consisted of casting various concrete mixes including a control and comparing standard properties. Properties tested included compressive strength, splitting tensile strength, flexural strength, modulus of elasticity, water permeability, chloride diffusion, pH dependence leaching and particle morphology. The results show that the concrete strength is not significantly affected when natural sand is replaced completely with red sand. The durability tests indicated high water permeability and high chloride diffusion due to the porosity of the red sand concrete, likely due to the low slump value. Leaching tests did not exceed New South Wales EPA guidelines.

Jan 1, 2006

It has become increasingly clear in recent years that human kind has developed the capacity to alter the environment of the Earth on a global scale. The changes are often subtle. This is particularly true in the case of stratospheric ozone. Ozone is produced primarily in the stratosphere, at altitudes in excess of 20 km, initially through the action of ultraviolet sunlight dissociating molecular oxygen. According to theory as it existed up to a few years ago, ozone is removed mainly by reaction with atomic oxygen. In the unperturbed environment, this reaction proceeds both directly, and by paths catalyzed by trace quantities of nitrogen radicals. Molina and Rowland [Nature, 249, 810, 1974] pointed out that decomposition of industrial chloroflurocarbons could in-troduce an additional source of radicals to the strato-sphere. Chlorine radicals are even more efficient than nitrogen in catalyzing recombination of oxygen atoms with ozone; models suggested that we might expect reductions in the vertical column density of ozone of as much as a few per cent over the next several decades. A reduction in ozone of x¦/a, by increasing the flux of ultraviolet sunlight reaching the surface, was predicted to result in an increase of about 2x% in the number of cases of skin cancer, with other less well defined impacts on the non-human environment for life.

Jan 1, 1990

As a society, the retiring age of workers is increasing. Individuals are having to consider working to an older age (beyond 55 years), the reason being to æpay offÆ debt, maintain a quality of life or, as a bigger picture, because society simply cannot afford the aging population. The Government is encouraging and promoting those approaching retirement to work to an older age to alleviate the financial burden of an aging population. In a working context those aged 55 years and over accounted for ten per cent of the Australian workforce in 1998 with this age group expected to account for half of the growth in the workforce between now and 2016. For the 60 - 64 years which account for less than three per cent in 1998, this group is expected to account for 15 per cent of the growth in the same period. As a result of individuals who have worked all their lives and in some cases æphysically hardÆ, they do not fully enjoy their years of retirement as a time when they get to choose what they want to do rather than what they have to do. Of particular interest are the physical or health related conditions that individuals end up with and the restrictions that ensue resulting in an individual being incapacitated either physically or with respect to the state of their health.

Jan 1, 2005

By A Garg

Squeezing can occur both in hard rock and in jointed rock mass as a result of over stressing. It is related to time dependent shearing, ie shear creep and is associated with the volumetric expansion (dilation) and radial inward displacement of the tunnel surface. While planning a tunnel in hard rock under a high cover of the order of 2 km it is desirable to identify the potential squeezing ground conditions and to select appropriate excavation technique and the support measures. There are several solutions to counter balance the squeezing ground viz over excavation of tunnel profile, assessing appropriate excavation technique, provision of a ductile primary support and time for providing tunnel lining. Low drivage rates and high cost due to support failures requiring rectification arising out of poor anticipation of tunnel closures and support pressures are major problems associated with tunnelling under squeezing ground conditions. Under squeezing ground conditions, the deformation will be gradual, therefore, in order to absorb deformations yielding supports are quite useful as primary support which provide a reliable low initial support pressure and permit uniform stress relief of the surrounding rock along with preventing rock from ravelling. The paper discusses the various factors which influence the selection of appropriate excavation technique and support measures in hard rock under squeezing ground conditions.

Jan 1, 1999