Search Documents

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

By D Stephenson, N R. Steward

“TerraFlowingTM” is a dewatering process that addresses both the value proposition of Tailings as a Resource™, and the safe storage of tailings. “TerraFlowingTM” incorporates two stages of cyclone dewatering followed by centrifugation of the final dilute tailings stream. In this process three dewatered tailings streams are produced; a primary cyclone underflow, a secondary cyclone underflow and a centrifuge pulp. These three streams can be combined, or used, in various configurations to achieve different outcomes. The ability to vary the cyclone and centrifuge operations and configuration enables this process to deal with tailings feed variations in particle size distribution and mineralogy and deliver consistency, or design variations, in particle size distribution, tailings solids concentrations and recoveries. Water recovery can be up to 85% of the total water in the tailings with a stackable final tailings product achieved if the three tailings streams are combined in the maximum solids concentration configuration. The primary cyclone can be operated to deliver a particle size distribution suitable for tailings storage facility embankment construction or alternatives such as concrete structures or shotcrete for support. The secondary cyclone underflow and centrifuge pulp is suitable for beaching deposition within the tailings storage facility.

Jul 1, 2021

By M H. Randell, J B. Haines

The Honeymoon Uranium Project comprises the Honeymoon Deposit,Goulds Dam Deposit and Yarramba Prospect in the Southern Lake Fromeregion, South Australia. Both the Yarramba Prospect and HoneymoonDeposit (which includes Honeymoon and East Kalkaroo orebodies) arelocated in the Yarramba Palaeovalley. The Goulds Dam Deposit is about75 km north west of Honeymoon, in the Billeroo Palaeovalley. Exploration for sediment-hosted uranium began in the area in the late1960s, culminating in the discovery of Honeymoon and Goulds Dam inthe early 1970s. In 1982, a 25 L/s demonstration plant was built atHoneymoon to confirm suitability for in situ leaching. The project was put on hold in 1983 due to changes in government policy. Southern Cross Resources Australia Pty Ltd acquired the project in mid 1997. Roll-front deposits form from a migrating geochemical cell, anadvancing reduction-oxidation interface between oxygenateduranium-bearing groundwater and its reduced aquifer host. The source of metal is uranium-anomalous granites, which were eroded fromsurrounding ranges. The weathered granites and resultant sediments are stripped of uranium by oxidised groundwaters, to form solutions carrying uranyl carbonate complexes. The solutions percolate down-slope through permeable sand zones until contacting a reduced environment where uranium precipitates. Uranium mineralisation occurs interstitially between and as thin coatings on sand grains, usually in the form of uraninite or coffinite. The palaeovalleys (previously termed palaeochannels) are incised intounderlying Cambrian/Precambrian basement rocks and filled withsemi-consolidated, largely un-cemented, Tertiary sediments of the Eyre Formation. The late Palaeocene to middle Eocene Eyre Formation is the basal unit of the Tertiary succession in the Callabonna Sub-basin of the Lake Eyre Basin. Further to the north, the Lake Eyre Basin overlies the Jurassic-Cretaceous Eromanga Basin, which comprises much of the Great Australian Basin. Eyre Formation sediments are in turn overlain by the late Tertiary Namba Formation and terrestrial Quaternary units. At Honeymoon, the Eyre Formation includes immature, pyritic,carbonaceous sands and gravels interbedded with lignite andkaolinite-illite-montmorillonite clays. It was deposited by braidedstreams during epeirogenic uplift of the Olary Ranges, accompanied bysubsidence of the Lake Eyre Basin. The Eyre Formation comprises aconsistent stratigraphy of interbedded sand and clay units that arecontinuous over the Honeymoon Deposit but with local variationindicating some hydrological connection between aquifers.In the Honeymoon orebody, uranium occurs within coarse-grained,pyritic sands where the basal sand pinches out between overlyingcarbonaceous clay and the southern palaeovalley slope. Its characteristics are typical of the well-developed, planar limb of a roll-front uranium deposit. Zonal changes related to the reduction-oxidation interfaces across the deposit are readily observable. The orebody extends for nearly 1000 m along the valley margin, is 400 m wide at its maximum and averages about 6 m in thickness. The East Kalkaroo orebody also lies near the southern margin of theYarramba Palaeovalley. It extends discontinuously for approximately 3.5 km and averages 200 m width, with significant uranium present in the Middle as well as the Basal Member. The Billeroo Palaeovalley extends northward for 40 km sub-parallel tothe western side of the Benagerie Ridge, is up to 5 km wide and hasgently dipping banks. Eyre Formation within the palaeovalley isconcealed beneath 90 m of Quaternary and Namba cover, isapproximately 40 m thick, and is sub-divided into three upward-finingunits, which are remarkably similar to the Yarramba Palaeovalleysequence.

Jan 1, 2001

By J Beniscelli

Some words to honour Pedro:Pedro was among the few persons with a very high level in geology modelling, resource and reserve estimation, geometallurgy development, sampling theory applications and a deep understanding of the mining industry needs. He had brilliant ideas about new developments on economic geology. He was always looking at the long-term and proposed challenging questions a decade in advance on their solution.The fundamental aim of geometallurgy is to add economic value to the mining of mine resources by timely providing information and knowledge about the relevant metallurgical variables represented by their space models. In this manner, geometallurgy allows obtaining the optimal design of a project, mitigating processing risks, optimising and supporting production plans and identifying and assessing mining business opportunities.This paper describes the conceptual framework and geometallurgical definitions and some of Codelco’s experience during the last 15 years.

Sep 5, 2011

By S D. Dessureault

In large coal strip mines, there are many different processes at work: stripping, overburden removal using trucks/shovels, cast blasting, slot dozer pushing, more fragmentation and further truck/shovel benches. A key component to each of these steps is the use of machines. In modern operations, most machine costs are tracked within Enterprise systems that transact costs and repair work order management. Similarly, in contemporary mines most machines are tracked using technology that provides precise performance measures for each key process. Such technologies include productivity monitors on draglines, dozers and drills and fleet management systems for trucks and shovels. Linking these two sources of seemingly disparate data û costs and performance by machine û would allow for the precise calculation of unit costs by specific machine. This is similar to an activity-based costing system, except in this machine-based system, calculations are made at an even finer granular level. There are many uses for such an integrated information system in mine planning and performance management, both in real-time and through historical analysis.A real-time fleet costs (FLC) measurement process was developed as part of a larger blending-related, multi-million dollar project centred on a centralised remote control room developed at the University of ArizonaÆs Mining Information Systems and Operations Management Mine Control Center. The FLC component of the overall blending system would allow a mine controller to manage the equipment fleet by viewing its cost in real time and, when mixed with other revenue-related components, the exact profit. For example, a mine controller may show high utilisation while still maintaining a production surplus. This could occur, for example, if the equipment is driven long distances. This might appear in traditional performance metrics as æhigh production performanceÆ, but in reality may prove less profitable. This paper discusses the technical development of the FLC, its deployment and its impact on controller performance, and compares mine profitability before and after its application.

Sep 26, 2011

By C Robertson, J Campos

The South African mining industry first experienced en-masse use of electronic detonators in the Narrow Reef environment using AELÆs ElectrodetÖ pre-set delay system. In recent years, programmable systems such as AELÆs SmartdetÖ have also established their position, and within both AEL and the mines there has been important learning around the strengths and weaknesses of these systems. In general, the fixed delay systems tend to be more easily appreciated by less-skilled work teams, and are very well suited to simple layouts, especially long, narrow blasts. However, development of programmable row controllers and series delay inserts has greatly expanded the field of usefulness of these systems while retaining most of the simplicity of use. The programmable systems are immensely flexible and therefore able to function under any condition, but require a higher level of discipline and knowledge. Much has been done to address this issue and make the systems user friendly, so the systems have converged to some extent. These systems are both valuable tools for achieving control over blasting in underground and surface applications. The choice of system is very dependent on the prevailing conditions. Accurate timing with electronic enhancements continues to show an increasing range of benefits to mining operations. There is a strong parallel with non electronic initiation systems which helps to understand the appropriate use of the systems.

Jan 1, 2001

By S Sineva, E Jak, M Shevchenko, D Shishin

This study represents a part of comprehensive research aimed at integrating nickel into a thermodynamic database constantly developed at Pyrosearch. The behaviour of Ni in calcium-ferrite slags is considered. An integrated approach combining experimental and thermodynamic modelling methods has been employed to predict phase equilibria in the NiO-CaO-FeO-Fe2O3 system under oxidising conditions and in equilibrium with the metal FeNi phase. The compositions of liquid slags and coexisting solid solutions have been determined through the analysis of equilibrated and quenched samples by electron probe microanalysis technique (EPMA). The research results are presented in the form of liquidus projections on the corresponding phase diagrams, considering both oxidising and reducing conditions. The solubility of Ni in spinel, dicalcium ferrite and calcium oxide as well as solubility of Fe and Ca in Ni monoxide, have been examined under several atmospheric conditions. Additionally, the compositions of the NiO-FeO monoxide in equilibrium with metal phase have been studied. The experimental data not only support the outcomes of thermodynamic modelling but also validate the parameters of the applied thermodynamic models, thus confirming the reliability and accuracy of the integrated approach.

Aug 21, 2024

The law relating to the Treaty of Waitangi is developing rapidly at present. A number of separate, but related, developments can be identified.

Jan 1, 1988

By R A. Pax

Operational grinding mills emit significant acoustic emissions which are a consequence of the dynamic environment prevailing inside them. From a technical perspective, the noise presents an opportunity to determine some details of the processes occurring inside the mills. The noise generated is not random and can be attributed to a range of events that occur inside these mills, consequently non-contact acoustic determinations of in-mill behaviour provide powerful insights into the operation of primary comminution tumbling mills. To enable a logically coherent picture to be formed of the processes inside a mill, arrays of microphones have been used. This approach allows a clearer picture of the in-mill behaviour of the charge to be accessed. In contrast to single microphone approaches, usually located near the expected charge toe position, an array of microphones allows much more useful information to be obtained from grinding mill noise.This paper will discuss and present data obtained from microphone arrays positioned at the toe and shoulder locations of a mill, and how this information can then be used for the optimisation of grinding mills in real-time.CITATION:Pax, R A, 2012. Determining mill operational efficiencies using non-contact acoustic emissions from microphone arrays, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 119-126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M Khanal, J Qin, B Shen, Y Duan, X Luo

Gaining confidence in interpreting rock and strata properties of the coalmine roof is necessary for design, maintenance, modelling and optimisation of roadways supports. One of the key causes of roadway instabilities experienced in underground coalmines is an extreme variable nature (thickness, competence, discontinuities etc) of the coalmine roof. Normally, the thickness and strength of the roof are characterised with the geotechnical and geological data gathered from exploration boreholes, which are drilled often at considerable distances apart. This limited data cannot capture localised geological variations in the coalmine roof. With this background, this paper explores feasibility of using measurement while drilling concept to perform geotechnical characterisation of the coalmine roof. The parameters, for example, penetration rate, rotary speed, torque, sound, vibration, obtained during the drilling process can provide valuable insights into geotechnical properties. The paper describes the progress of the experimental work conducted at the laboratory on synthesized concrete samples representing various rock strata using a field-scale drilling machine. The samples with and without interfaces have been tested to replicate various underground roof strata. The signals returned from the drill machine, as the drill bit passes through the layers, have been analysed and interpreted to characterise whether the drill response data can differentiate various strengths associated with the rock layers. The initial laboratory results are promising as they show distinct responses of the various sample blocks in a controlled environment. The drilling data can differentiate the synthesized rock samples and detect ‘signatures’ of the roof strength variability and delineation of lithological interfaces (transitions). The weight and torque on the bit vary and show dependency on the strength of the blocks.

Nov 29, 2022

By X S. Li

The modern mechanical excavation machines have enough power for cutting hard rock. The ‘bottle neck’ which limits the use of machines for hard rock excavation is ‘cutting tool’. To cut hard and abrasive rock, CSIRO has been developing Super Material Abrasive Resistant Tools (SMART*CUT). SMART*CUT technology replaces the tungsten carbide (WC) tip of conventional pick with thermally stable diamond composite (TSDC) and attaches the TSDC tip to steel tool body with CSIRO worldwide patented bonding technology. This paper introduces the key features of SMART*CUT, compares its performance with conventional WC tipped tools, discusses the challenges faced by SMART*CUT and the further developments needed for successful application of SMART*CUT to mining industries.

Nov 22, 2011

By L Yao, J Li, C Sammut, B Li

The underground mine environment is inherently complex and hazardous, which necessitates ensuring mining workers’ safety. With the fast development of AI techniques, human activity recognition has become a crucial task to enhance daily life, especially in such challenging settings. This enables automatic monitoring and detection of the mine workers’ activities and operations on a large scale, which leads to better support of workers’ safety and welfare. Existing traditional uni-modal approaches, which use data of one single modality, suffer from low data quality and noise, so they struggle to generalise effectively in such extreme conditions (Li et al, 2022). As underground mines have extreme and complicated environments, such as dust, low light, signal interference, and rugged terrain, uni-modal approaches could not resolve such obstacles and are not suitable for real-world deployment. Multi-modal human activity recognition approaches could use data from multi-modal sources, thus capturing complementary information and producing robust and effective performance in recognising and monitoring mining activities. In this case, designing suitable multi-sensor hardware and AI activity recognition models has become a pivotal task. Producing efficient multi-modal approaches for edge deployment is another problem worth exploring.

Sep 1, 2024

Mining education in Ballarat has a long and proud history dating back to the 1870s. Today the School of Engineering continues this tradition at the University of Ballarat. The recent review of Tertiary Minerals Education by the Minerals Council of Australia has questioned the current situation regarding Minerals tertiary education in Australia and recommendations have been made regarding the future of minerals tertiary education. This paper initially examines the original recommendations made by the Minerals Council of Australia and assesses subsequent changes made to these recommendations. Secondly the paper outlines the future shape of mining education in the light of these recommendations given that they are implemented. Finally the future delivery of mining education is discussed, particularly with respect to the impact of modern technologies.

Jan 1, 2004

By A Turichshev

The synthetic rock mass (SRM) approach for modelling jointed and veined rock has been at the forefront of caving geomechanics research for years. A well-constructed and calibrated SRM model can capture the full rock behaviour at a macroscopic scale. Traditionally, SRM technology employed bonded particle models (BPM) due to their ability to model rock’s response to loading without prior specification of behaviour. The SRM modelling process requires the BPM to simulate intact rock and the subsequent introduction of fractures or veins by changing bonding characteristics between the particles. However, bonded particle materials have difficulty reproducing both the compressive and tensile strengths of intact rock. This and other limitations of BPM have been the driving force in exploring the potential of grain-based (2D) and bonded block (3D) models (BBM).This paper reports on recent work exploring the applicability of both BPMs and BBMs in 3D to the modelling of intact rock. The advantages and limitations of both BPMs and BBMs are addressed based on the results of numerical simulations using the PFC3D and 3DEC distinct element codes. The preliminary results suggest that BBMs are better suited for simulating intact rock behaviour than BPMs. Ongoing work aims to better qualify the applicability of BBMs under different conditions. This has significant implications for our understanding of rock mass behaviour in a caving environment.CITATION:Turichshev, A and Hadjigeorgiou, J, 2016. Simulating intact rock behaviour using bonded particle and bonded block models, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 453–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J Q. Shi, M Karakus, Y Liu

Predicting the spatial distribution of rock mass properties in cave mining is a critical challenge. In this study, we introduce a novel machine learning-based model to advance our comprehension of rock behaviour. This model specifically focuses on the spatial distribution of rock mass and mechanical properties, a crucial aspect of our understanding of rock mechanics. Our model is inspired by the recognition that neighbouring information serves as crucial prior knowledge for predicting the spatial distribution of these properties, wherein closer neighbours are likely to exhibit similar characteristics. To effectively capture and model these neighbour relationships, we design a neural network-based model to map the spatial locations within the data set into a new highdimensional space. Within this transformed space, we utilise Euclidean distance to identify N neighbours. Leveraging these neighbours, we introduce a straightforward yet highly effective approach—label propagation—to construct a graph that illustrates neighbour relationships. This graph not only facilitates the prediction of the spatial distribution of rock mass properties but also offers a measure of uncertainty for these predictions. We validate the proposed method using a real rock data set and showcase its efficacy in capturing intricate relationships and distributions within rock properties, enabling precise predictions across diverse spatial scales. Our results underscore the potential of machine learning-based approaches to revolutionise the field of rock mechanics, providing valuable insights applicable to geotechnical engineering, mining, and other sectors where an accurate understanding of rock properties is paramount. This model has direct practical implications, offering a new tool for geotechnical engineers and mining professionals to enhance their understanding and prediction of rock properties, thereby improving safety and efficiency in their operations.

Sep 1, 2024

By D Beck, E Jones

The measurement and management of deformation in underground excavations is a key responsibility of geotechnical and mining engineers. A critical aspect of these roles is to ensure there is sufficient ground support capacity for the expected demand.Current methodologies for monitoring deformation and ground support serviceability-limits require measuring displacement at distinct points, or using visual observations. These current methods limit the assessment to a qualitative interpretation of deformation across the entire excavation.Recent advancements of Light Detection and Ranging (LiDar) technology permit a new method for monitoring deformation that allow a full 3D image of extended sections of an excavation to be precisely scanned. The results from the comparison with subsequent scans provide valuable information on the magnitude, direction and extent of regions exceeding the ground support serviceability-limits. This new method now provides a quantitative assessment across the entire excavation being monitored.The implementation of regular scanning has been demonstrated to be highly advantageous not only at mines with swelling or squeezing ground, but also at mines with rapid seismic induced deformation. The use of LiDar technology as a routine deformation measurement tool for geotechnical and mining engineers (and further applications) are discussed in more detail in this paper.CITATION:Jones, E and Beck, D, 2017. The use of 3D laser scanning for deformation monitoring in underground mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

Nickel WestÆs Kalgoorlie Nickel Smelter operates three Peirce-Smith converters, each processing 110 tonnes of matte per charge. The vessels are lined with chrome-magnesia refractory with a mouth traditionally constructed from steel liner plates, protected with cast refractory. Mouth refractory is damaged by molten material and the action of cleaning solid buildup off the mouth. Once damage has accumulated, the mouth must be frequently maintained with hot refractory gunning or a mouth leak may occur. Such a leak requires a 32 hour repair period. A converter mouth redesign program was undertaken with the aim of reducing the rate of mouth damage during operation, eliminating mouth leaks and shortening mouth replacement times during vessel rebuild periods. An overview of the redesign process and operational performance is contained herein.

Jan 1, 2005

By Campbell Brown G F

THE Mount Morgan mine has, from the time of its historical discovery, been the subject of investigation and speculation by geologists and mining engineers. The first examination was made by Dr. R. L. Jack, in 1884. He came to the conclusion, from theevidence then available, that nothing but a thermal spring in the open air-otherwise a geyser-could account for the formation of the ore body. This report attracted world-wide attention at the time. Since then the mine has been examined by most of the leading geologists of Australia, and by many from elsewhere. In all cases the examination has only extended over a period' of a few days or weeks, and in the light of present knowledge of the deposit we know that sufficient data could not be obtained in such a short time to warrant the statement of definite conclusions. It is not to be wondered at, therefore, that a considerable difference of opinion exists as to the genesis of the deposit. That the company considered more detailed investigation necessary is shown by the fact that some thirteen years ago it employed Mr. Charles Walker as geological surveyor on the .mine. At that time also the data available was insufficient to give satisfactory results. It is, however, a matter for comment that none of the geological reports on the property took notice of the increase of copper values in the ore with depth, though the present workings and diamond-drilling...

Jan 1, 1911

By Guo H

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack Orientation.

Jan 1, 1992

The appraisal of mineral reserves by a lender is carried out at the initial stages in developing a loan for a mine. The depth of investigations is influenced by the competence of the explorer, the type of commodity and knowledge of the geological environment. The lender looks for a reserve life which exceeds the term of the loan plus contingencies for events such as cost over-runs, adverse markets and production difficulties. The physical features of importance are discussed. Factors with direct financial implications are considered for their incorp- oration in sensitivity analyses to allow risk appraisal. When satisfied, the lender can then proceed to review cash flow forecasts, the basic strength of the project, then determine with the borrower the components and alternat- ives of a loan package.

Jan 1, 1979