Search Documents

By V Kainulainen

Sandvik Tamrock Corp has developed an underground rock flow simulation tool OPTIMINEÖ which is a direct simulation tool for matching suitable technology in rock material flow for underground mine layouts and production requirements. The tool gives the possibility of determining intersections, limitations and critical points in the layout and working procedures at an early stage of a new mine/mining area planning process. The tool combines the supplier machine knowledge with operational know-how and mine environment. It can be used for identifying the effect of an individual incident such as the effect of one additional turn in a continuous loading cycle to the daily capacity. This paper discusses the way the OPTIMINEÖ simulation tool operates, the benefits and restrictions, and reviews how it simulates some example cases and how the mines benefit from the tool in maximising the performance and optimising the mobile fleet, scheduling work and fine-tuning the layout.

Jan 1, 2000

By Thomas L. J

A series of tests on rock stress measurement devices used with the overcoring method indicated that improvements could be made in their construction. A prototype inclusion cell was developed with strain gauge rosettes bonded to a 0.05 mm thickness stainless steel sheet which was formed into a cylinder around two end pieces. The finished diameter was slightly larger than previous cells so that the thinner plate and the reduced annulus of Araldite cement in the installation borehole gave a better response in the laboratory than the other cells tested, especially in simulated bedded rock. It was less affected by inhomogeneity and temperature changes. Its high sensitivity should make it suitable for both absolute stress measurement and field monitoring. A table of comparative readings is given for the new cell and for four other devices used in simulated in-situ rock conditions.

Jan 1, 1992

Scale build-up in titanium palladium alloy spent electrolyte heat exchangers in the residue treatment plant commissioned at Risdon, Tasmania in 1971 was shown to be a mixture of manganese dioxide and anhydrite (CaSO4). The manganese dioxide was deposited as a result of thermal decomposition of permanganate ions present in the spent electrolyte. It was shown that deposition of manganese dioxide and associated anhydrite scale could be prevented by prior reduction of permanganate ions to the manganous (Mn++) state by the addition of ferrous ions. In the plant this was conveniently accomplished by injecting into the inlet line to the heat exchangers sufficient zinc plant solution containing ferrous sulfate to decolourise the spent electrolyte. This action prevented deposition of such scale for another 21 years, until the heaters were finally decommissioned in March 1992. Measurements indicated that addition of the reducing solution lowered the anodic potential of the titanium alloy by 200 - 300 mV (depending on the solution resistance), but that it was still +300 to 400 mV with respect to a standard calomel electrode. It was shown that, if necessary, a small impressed current could be applied to provide anodic protection. Before scale deposition was overcome by the addition of ferrous sulfate solution, badly scaled heat exchangers were cleaned by recirculating a solution of hydrogen peroxide in spent electrolyte or dilute aqueous sulfuric acid, after laboratory testing of a variety of possible solvents for the scale. Corrosion tests indicated that attack on the titanium alloy by the acidic peroxide cleaning solution was insignificant.

Jan 1, 2005

By P T. Hick, T J. Cudahy, M S. Caccetta

Dust derived from mining and handling of ore has been identified as a major concern for the mining industry in Australia and may be critical to the future viability of some resource industries (CSIRO, 1999). Operational techniques to derive accurate measurements of anthropogenic dust on vegetation and infrastructure are necessary for the long-term management and monitoring of the environment surrounding mining operations. Airborne hyperspectral VNIR-SWIR systems can potentially provide these monitoring data. This paper outlines a method developed for deriving quantitative measurements of dust quantity on mangroves using remotely-sensed airborne hyperspectral data. The results show that it is possible to detect and quantitatively map iron oxide dust distribution using properly calibrated airborne visible to short wave infrared (VNIR-SWIR) data.

Jan 1, 2002

Modelling of Synergistic Effect of Cyanex 302 and D2EHPA in Zinc Solvent Extraction A comprehensive model is presented to predict the synergistic effect of D2EHPA and Cyanex 302 on co-extraction of zinc and manganese. The experimental results indicated that pH, temperature and the extractants ratio have strong effects on the extraction process. Correlations were proposed to predict the distribution coefficient of zinc and manganese between two phases at different conditions by multiple linear regression. The correlations were simplified by eliminating less important terms by analysis of variance. Optimum conditions (ie pH, temperature, extractants ratio and aqueous to oil phase volumetric ratio) for obtaining maximum separation of zinc from manganese at different zinc concentrations and number of extraction stages were determined. For finding the optimum condition genetic algorithm was used. Comparison the model estimations and the experimental data show that the presented model has good ability to predict the behaviours of zinc extraction system over Cyanex 302 and D2EHPA.

Sep 13, 2010

By M Devia, J Rapkoch

This paper is intended to help design engineers, operating staff and plant managers understand the principles of metallurgical gas handling systems design. It also explains operating, safety and energy savings issues that the designer should take into consideration in the design of process off-gas systems for sulfide smelters. Primary smelting reactors, converters, and other off-gas sources impose challenging duty requirements on the various components of the gas handling systems. This paper reviews the design of common system components including the hood for gas capture at the system inlet, gas conditioning, gas cleaning, ductwork, dampers, hot gas fans, and the appropriate use of instrumentation and controls. The engineer must also be aware of how ductwork system effects and heat losses influence system performance. Also, the analysis of a recently-designed gas handling system will be reviewed, which includes high-strength SO2 gas from a smelting reactor, asymmetrically located Peirce-Smith converters, and a gas mixing chamber to mix the gases before they are sent to two acid plants of different sizes.

Jan 1, 2005

By Schommarz KH, Dunne RC, Goodall CM

Column cells are widely used today for the recovery of base metals by flotation. Their use for the flotation of iron sulphides has not been as rapid. Australia has pioneered the use of large rougher flotation columns. During the last six years, seven rougher columns have been installed on gold mines treating iron sulphides and the technical viability of this technology has been demonstrated. Laboratory column testwork on a gold bearing iron sulphide ore demonstrated the effects of both physical and chemical parameters. In general the large commercial columns operate over a broad range of conditions depending on the downstream treatment of the flotation concentrate. The addition of wash water to commercial columns is not universally applied and there appears to be a need for a better wash water System.

Jan 1, 1993

For decades strip mining with discon tinuously operating 'draglines and shovels has been the most economical operation method in the shallow hard coal opencast mines of Aust- ralia, North-America and some other countries. Continuously operating equipment such as bucket chain excavators and bucket wheel excavators in combination with conveyor belt systems, conveyor bridges and stackers had been deve- loped in Germany; during the last 25 years this type of equipment has been further developed in order to allow a high degree of rationaliza= tion as to opencast mines in unconsolidated overburden in Germany, in many European couh- tries, in India and in Victoria. The differing compactness of the layers to be mined, the increasing mining depth, the adverse over- burden to coal ratio and geotechnical con- ditions account for the combined use of con- tinuously and discontinuously operating equip- ment and systems. This paper is to demonstrate some projects showing the combination of continuously and discontinuously operating equipment which aims at optimizing opencast mine operations. It will be reported on the following combinations: - combined use of bucket wheel excavator/

Jan 1, 1981

By Smith P

The past 20 years have seen the replacement of hydraulic control of longwall mining systems by the neater. smaller and better controlled electronic units.Early problems of moisture and other effects on reliability were overcome to see electronically controlled supports chosen for Corrimal Colliery ten years ago. Lessons from Corrimal and elsewhere, with following improvements and sophistication led to wider use as exemplified by Meco and other electronically controlled supports used in more recent installations in New South Wales, Queensland, USA and Czechoslovakia of the total of over 80 electronically controlled support installations worldwide in the past decade. Present work is toward a fully "integrated face" of British Coal by 1993, incorporating the Meco automatic face straightening system already due for practical use in the UK later this year. However the manless face still appears to be some way off although the present minimum crews and close monitoring, including early warning, are promising stages.

Jan 1, 1991

By R Milton, D Hake, H Sprague

The North Western Sewer tunnel extends over 11.5 km in the North Western suburbs of Melbourne.The $253 million tunnel project provides a critical link in the Melbourne Sewer Network. The existing sewers fail to service the increasing demands of the growing population of the North West regions of Melbourne. This project will protect the environment and improve the standards of service of the existing system. This paper concentrates on Section three of this project, consisting of the final 4 km of the Contract, three access shafts and a cut and cover section of tunnel.Transfield Tunnelling as Head Contractor constructed the tunnel for Melbourne Water Corporation, with Enetech Streamline, formally Streamline Australia, a trading arm of Melbourne Water acting as Superintendent.Excavation of Section three of this project commenced in September 1994 and project completion is scheduled for October 1998. The tunnel passes below the residential suburb of Essendon, through some of the most challenging ground conditions ever attempted to be tunnelled in Australia.

Jan 1, 1999

By Slechta JJ

The performance of a hydrocyclone treating fine coal has been examined over a wide range of feed and operating conditions.The results were expressed in terms of partition curves from which the water split to the oversize flowstream,the corrected separation size and reduced partition curves were determined-.The following conclusions were obtained. (a) The water split to the oversize flowstream was found to be dependent upon the vortex finder and spigot diameters of the cyclone and the flowrate and solids content of the feed slurry. (b) The corrected separation size was dependent on the solids content of the feed,and the vortex finder and spigot diameters.The hydraulic pressure (or flowrate) of the feed slurry did not have a significant effect.This phenomenon could be explained in terms of crowding of the particles at the Spigot.

Jan 1, 1984

By R Heath, P Rose, L Coetser

A sustained eight-year major research effort has been undertaken in South Africa to develop integrated passive water treatment systems for the sustainable removal of sulfates, while simultaneously addressing the removal of metals and acidity. The research effort addressed the problem both at a fundamental science level and at the more empirical pilot plant level. Whereas there are numerous anaerobic sulfate reducing reactors in operation on mine waters that remove some sulfate together with metals and acidity, these are typically plagued by low sulfate removal efficiency and gradual reductions in overall reactor efficiency with time. The South African research effort has focused on understanding the fundamental microbiological and biochemical reactions that occur in anaerobic reactors filled with lignocellulosic material and subjected to high sulfate water. Hypotheses have been developed that differentiate the reactions occurring in such a reactor into groups that should be individually optimised and these hypotheses have been verified through rigorous laboratory and pilot scale studies. The results of this research are incorporated into a patented multi-stage integrated passive treatment system that is capable of sustained high rate removal of sulfates, metals and acidity.

Jan 1, 2003

Engineering availability of the 120/200 tonne Wabco haulpak fleet at Mt. Whaleback was in the mid fifties and unstable. The project to achieve a reliable 66% during 1980 highlighted "plannable" maintenance, short cycle scheduling, condition monitoring, backlog control, and, above all, the importance of involving all affected people. It is not sufficient for consultants to design systems and make them work. The people who use the system must understand it, support it and "own" it. In this way, they will develop it and improve results after the outside help has been withdrawn INTRODUCTION In early 1979, PA proposed a programme to improve engineering availability of the Mt. Newman Mining fleet of 70 Wabco haulpak trucks of which 53 were 120 tonne and 17 were 200 tonne units. (Subsequently five 200 tonne trucks from Hamersley Iron were added to the fleet). The ore truck workshop was also responsible for 75 tonne trucks used as water trucks and general purpose vehicles. The need for action was clear. The fleet was achieving availability in the "mid fifties" with wide variations indicating that the fleet was becoming unreliable. Projected tonnages required a reliable 66% availability to be

Jan 1, 1982

By D R. Lueking

A technology involving separate unit processes for the generation and use of ferric ions for the oxidation of sulphidic minerals has been developed. The technology utilises a stand-alone automated bioreactor for ferric-ion generation (termed SAAB-FIG) and produces a low pH, ferric ion-rich leach liquor with a high oxidation potential. This leach liquor is then employed, in a separate unit process, to oxidise sulphidic minerals and regenerate ferrous iron that may subsequently be recycled to the bioreactor for the continual generation of ferric ions. The technique was successfully applied for the recovery of copper from chalcocite (Cu2S) and chalcopyrite (CuFeS2), as well as other ores and concentrates containing copper sulphide minerals. Coarse ore, ground ore and concentrates were treated with acidic solutions containing 8 to 12 (g/L) Fe(III) ions at a variety of temperatures. This process yielded over 50 per cent of the contained copper from both chalcopyrite and chalcocite samples. Maximum reaction rates and copper recoveries were found to be highly dependent upon temperature and pH and leach liquors containing bacterial cells displayed little difference in their leaching efficiency when compared to cell-free leach liquors.

Jan 1, 2000

The heavy media cyclones at Argyle Diamonds are subjected to extremely abrasive service conditions and have been the subject of a development program from the time the first ore was treated in the AKl processing plant. In the past ten years the cyclones have been re-engineered from a standard DSM design, in which some components would only last four days, to the current Argyle design in which the minimum component life is 175 days. Development has focused upon the elimination of turbulence in the cyclone and combating unavoidable abrasion through the use of appropriate wear materials.

Jan 1, 1996

The original leases making up today's North Kalgurli Mines were developed by independent companies on an ad hoc basis. The major disadvantage which now arises is the varying levels of mining horizons. From Kalgurli Shaft in the south, through main Shaft and to Croesus Shaft in the north, there are three separate sets of levels. work has commenced to link the three areas with either common levels or new development which will facilitate common access and haulage via Main Shaft.Generally, the workings at North Kalgurli were established at the turn of the century. The introduction of techniques and equipment to bring the mine into the 20th Century has been difficult and slow. The general size of openings, a widespread workforce and complex ore distribution often make innovation and change more than a challenge.

Jan 1, 1985

By Hosking IA, Mirkov P

Among the solutions currently being considered for improving traffic flow in Sydney are the construction of major road tunnels, principally the Eastern Distributor Tunnels, leading from the end of the Cahill Expressway to Drivers Triangle and South of Taylor Square and the Sydney Harbour Tunnel, which incorporates sections of driven tunnel at the northern and southern sides of the harbour. The Eastern Distributor Tunnels, known as Stages 2 and 3 of the Eastern Distributor Scheme comprise: Stage 2 - A south bound two lane tunnel from north of William Street to Driver's Triangle. The southern end includes two Y junctions (locally 3 to 4 lane widths) with exits into South Dowling Street, Anzac Parade and Moore Park Road. Stage 3 - A north bound, two lane tunnel from Taylor Square to Palmer Street just north of William Street. Further details of the Eastern Distributor Tunnels are given in the paper by Baxter, Chappel and Fishburn (1986) which is included in this conference.

Jan 1, 1987

By J C. Furness, F S. Cannon

Metal casting operations are a significant source of hazardous air pollutants. In particular, high production iron foundries emit significant quantities of volatile organic compounds (VOCs) during pouring, cooling and shakeout of iron castings made in green sand molds. End-of-the-pipeline capture and destruction methods to reduce VOC emissions add crippling costs to foundries. Alternately, the incorporation of advanced oxidants (AO) into metal casting green sand systems has been shown to reduce emissions from high production iron foundries in the US, and at the same time reduce operating costs. Cost savings are driven by the benefits of AO in clay recovery systems. Emissions reductions are the direct result of cascading AO-based reactions taking place in green sand molds. This sustainable greening of the metal casting process is a prototype for the development of other AO and non-AO process-based solutions for sustainable high temperature processing of materials. Fundamentals of AO technologies will be discussed along with the performance characteristics of AO processing systems in the metal casting industry and the breadth of other processing and remediation applications for which AO technologies have the potential to be successfully employed.

Jan 1, 2002

By Floyd JM

Conventional smelting reactor systems were designed to recover only one main element from their feedstocks. They did not possess sufficient flexibility to allow optimisation of co-production of multiple values from a complex feed.New reactors such as Sirosmelt and Top Blown Rotary Converters are providing new possibilities for making separation between components and this is of great significance for the complex feeds which are becoming prevalent in the metal extraction industry.Process routes using chemical procedures which take advantage of the flexibility of these reactors will be discussed in relation to a number of possible feedstocks.

Jan 1, 1985

Organic dyes such as nigrosine and sun yellow act as depressants for carbonaceous particles in the, flotation of sulphide ores. Depression is achieved when initially hydrophobic organic surfaces are made hydrophilic by preferential adsorption of dye molecules. Experimental studies, mainly on Mount Isa ores, indicate that dyes are adsorbed as planar anionic micelles attached to carbonaceous surfaces by van der Waals and ion exchange attractive interactions. Relationships appear to exist between the amount of organic matter on the surface of ground particles, the surface area of the particles, the "saturation" adsorptions of dyes, and the degree of difficulty experienced during froth flotation.

Jan 1, 1975