Search Documents

By A. Desbiens, M. Maldonado, R. del Villar, Aguilera. R.

This work details the application of a multiple model approach to estimate frother concentration in flotation processes. The methodology consists of identifying a set of linear dynamic models representing the effect of gas rate on the collection-zone gas holdup at different known frother concentrations (calibration step). An adaptive law is then obtained using Bayes' rule to evaluate the conditional probability that each model represents the observed system behavior. In this way, a frother concentration estimate is calculated as a weighted sum of model probabilities and their associated (known) frother concentrations. Experimental results conducted in a two-phase system using Dowfroth250C are promising. Modeling and analysis for MIBC frother are also provided.

Jan 1, 2009

By S. Gheibi, H. S. B. Duzgun, N. Dadashzadeh

It is widely recognized that there are various uncertainties in the analysis of rock slope stability owing to inadequate information for site characterization and inherent variability and measurement errors in geological and corresponding parameters. Therefore, reliability-based approaches that allow the systematic and quantitative treatment of these uncertainties have become a topic of increasing interest in rock slope engineering. There has been extensive reliability analysis of rock slope stability in the literature. However, all of these analyses are based on the First-Order Reliability Method (FORM). The probability of failure of a rock slope in the First-Order Reliability Method is provided by a linear approximation of the failure function. The FORM is most commonly used because it is efficient; its accuracy, however, deteriorates when the nonlinearity of limit-state function increases. A better approximation of the failure function can establish a more accurate value of the probability of failure. The Second-Order Reliability Method (SORM) overcomes this drawback with a cost of lower efficiency in terms of the number of function calls and computation expenses. Despite considerable studies of the application of the SORM in other engineering fields, a few attempts have been made in the slope stability studies. In this study, a recently published Second-Order Reliability Method with First-Order Efficiency (SORM-FOE) is implemented on a selected rock slope in Amasya, Turkey. The SORM-FOE overcomes the low efficiency of the SORM by decreasing the number of function calls. The probability of failure of both FORM and SORM-FOE are obtained and the results are compared. It is shown that, in high value of failure probability, SORM’s do not significantly affect the analysis and design. However, in very low failure probability, the discrepancy between FORM and SORM-FOE becomes pronounced. It is also shown that, where the second order methods are required, the SORM-FOE is more efficient than the conventional curvature fitting methods in terms of computational costs.

Jan 1, 2015

By G. A. Maki, P. J. Fullman, R. G. Roden

"In October 1984, Rocanville Division began using a stacking system to handle potash mill tailings. Previous to this date, mill tailings were slurried to the top of the tailings pile and allowed to debrine while flowing down the pile. With the new stacking system, slurried tailings are fed to mobile stackers. The stackers consist of cyclone packs to debrine the tailings and drag conveyors with screw discharges to deposit the tailings onto the existing pile. This paper deals with the various aspects of the project from conception to its present state.IntroductionPrevious to 1984, when the stacking project was first implemented, potash mill tailings were handled as follows. Mill tailings were first debrined to approximately 65010 solids using a cyclone cluster. The cyclone underflows were then introduced onto a vacuum scroll filter table. Here the tailings were further debrined and discharged into the disposal tank where the tailings were reslurried with reclaim brine and pumped to the tailings disposal site. At the disposal site the slurry was discharged onto the tailings pile and by a natural settling process the tailings were debrined with the brine ultimately collected in the reclaim brine ponds. The shape and profile of the tailings pile was controlled by building salt dykes to control the flow of the discharged tailings slurry. As the tailings pile grew in height, booster pumps were added to the disposal system."

Jan 1, 1990

By P. Van Marcke, X. Sillen, G. J. Chen, I. Troullinos, A. Dizier, J. Leysens, X. L. Li, J. Verstricht

"In Belgium, Boom Clay is considered as one of the potential host formations for the disposal of the High Level radioactive Waste (HLW). The URL HADES at 223 m depth at Mol site was constructed in order to study the feasibility of HLW disposal in Boom Clay. Since 1995, the URL R&D programme has focused on large scale demonstration tests like the PRACLAY experiment.The PRACLAY in-situ experiments include a set of three tests: The gallery and crossing test, PRACLAY Heater test and PRACLAY seal test. The main aim of the Heater test is to study at a large scale the thermal impact of a HLW repository on the host rock. The test is housed in the PRACLAY gallery. A hydraulic seal, made of compacted swelling and low permeable bentonite annular ring was installed at the intersection between the heated and the non-heated part of the gallery. The primary objective of the seal is to provide undrained hydraulic boundary conditions for the Heater Test.The PRACLAY gallery was constructed in 2007 and the hydraulic seal was installed in 2010. The bentonite is hydrated by natural and artificial process. The swelling, total pressure and pore pressure of the bentonite are continuously measured and analysed by numerical simulations to get a better understanding of this hydration processes. The performance of the seal is tested systematically by means of gas injection breakthrough tests and permeability tests at interface bentonite / Boom Clay and in the Boom Clay around the seal.The PRACLAY Heater will be turned on at the end of Oct. 2014, since a sufficient seal swelling has been attained to fulfill its role for the PRACLAY Heater test. This paper will focus on the PRACLAY Seal test: How we understand the process behind the hydration of the bentonite and how we test the performance of the bentonite seal."

Jan 1, 2015

By P. Reyes

The start up and operational optimization of the No. 3 Oxygen Plant at the Caletones Copper Smelter of the Codelco - Chile El Teniente Division is summarized. In addition, the economic impact of such optimization on the production cost of oxygen and others aspects associated to the operational robustness as well is detailed.

Jan 1, 2007

By M. Feinendegen, Ph. Siebert, C. Clauser, K. Willbrand, M. Ziegler

"Three institutes of RWTH Aachen University collaborate on laboratory tests and numerical simulations of hydraulically driven fractures in igneous rocks. The project´s target is to enhance the understanding of hydraulic induced fractures for deep geothermal energy exploration. Based on the idea of creating new discrete fractures in hot dry rock (HDR) reservoirs, the current project stage deals with this process on a laboratory scale. Especially for this purpose, a new testing facility has been developed and laboratory tests are performed to verify a hydraulic fracture propagation code based on the extended finite element method (XFEM). The testing facility enables us to initiate and propagate fractures in large samples of dense rock under triaxial confining pressures and to monitor the fracture propagation by extensive measurements. This contribution gives a short introduction to the project‘s background and mainly focusses on the test facility, the experimental procedure and exemplary results.INTRODUCTIONThe most efficient technique to increase the permeability of subsurface rock is to initiate and open fractures by applying hydraulic pressure from a packed borehole-section and to inject fluid into these fractures to propagate them. Since its first use in petro industries to enhance the production of wells in natural gas and oil reservoirs, the interest in targeted creation of hydraulic fractures has increased exponentially. As the key technology to the extraction of unconventional gas from shale, hydraulic fracturing (HF) became a major topic in a heated public debate. Based on the fact that a fracture tends to propagate in a direction perpendicular to the minimal principal stress, hydraulic fracturing has become an established tool for estimating geological stress states in almost any depth. Enhanced geothermal systems (EGS) in HDR reservoirs use engineered fractures as a heat exchanging system for a cycling fluid driving a power plant."

Jan 1, 2015

By M. Kellner

Due to continuously growing resource demands and increasing requirements for sustainability, safety and environmental protection on the other hand, the mining industry is being subjected to these additional requirements. Over the past few decades progress has been made in all topics. In 1987, the United Nations published the following in the Brundtland Report: ?development that meets the needs of the present without compromising the ability of future generations to meet their own needs.?[5] The term ?Blue Mining? means to work sustainably, economically, ecologically, and efficiently while also improving ergonomics, for example by increasing automation. An example of how mining can actively be involved in energy management will be shown. Initial evaluations of underground cavitites were done for purpose of energy storage. The planning and construction of underground pump storage plants both in active and inactive mining operations was also investigated.

Aug 1, 2013

By W. Kempson

"Mining Companies have producing assets in increasingly diverse portions of the world. It is not uncommon that the owner, the design team, the mine contractors and the operators are all based in different countries. While these assets are always subject to the regulatory requirement of those countries there have not been international standards available to review and evaluate these assets. This becomes particularly important when considering safety critical items such as tailings dams, vertical shaft systems and autonomous vehicles to highlight a few. The work currently being completed in ISO ensures these standards will be available and will be generated by and subscribed to on an international basis, thus removing the potential for patriotic partisanship and ensuring safe and predictable systems are installed. This paper will discuss the benefits of the international standards, the structure of the teams and working groups who are generating these standards as well as the process by which the standards are generated. This will allow insight into the creation of the standard and will aim to demonstrate the “neutral” and technically strong manner in which the generation of these standards is achieved. In addition, the paper will discuss the standards which have been produced in the last five years as well as the current standards which are in place. The finale will discuss upcoming work and the timelines in which it is anticipated these will be completed. INTRODUCTION Mining Companies have producing assets in increasingly diverse portions of the world. While these assets are always subject to the regulatory requirement of those countries, there have not been international standards available to review and evaluate these assets. This becomes particularly important when considering safety critical areas such as vertical shaft systems, tailings dams and autonomous vehicles to highlight a couple. The work currently being completed in the International Organization for Standardization (ISO) ensure these standards will be available and will be generated by and subscribed to on an international basis, thus removing the potential for patriotic partisanship and ensuring safe and predictable systems are installed. The ISO/TC 82 – Mining was founded in 1955. This was an active committee until it was thought that the standards at the time were adequate and the Technical Committee was put on “Care and Maintenance”. In 2012 countries lobbied ISO to pull this committee from dormancy and restart it, this happened in in the same year."

Jan 1, 2019

By D. J. Reddish

The paper describes a case study where numerical modelling has been applied to predict potential risks associated with inflows of water in active mine workings from an overlying sandstone aquifer. The objective of the modelling was to predict the development of strata fractures and strains as the longwall panels were extracted and investigate their relationship to an sandstone aquifer. The numerical modelling study also included the investigation of the effect of mining on a fault that existed close to the start position of one of the panels. The potential effects of mining on the fault were undertaken by parametric studies adjusting properties for the fault and the relative position of extractions, which allowed the mine planner to position the panel layout accordingly.

May 1, 2003

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, L. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite by an acid pressure leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project.

Jan 1, 2004

By Dr. Rory Cameron, Dr. Terry Cheng, Dr. Nadia Mykytczuk, Ian Bedard, Kristie Tarr, Ruth Joseph

Pyrrhotite-rich tailings from Sudbury, Ontario mining activities are known to contain significant amounts of EV metals, such as nickel and cobalt.  CanmetMINING has developed a novel bioleaching process for recovering the nickel and cobalt (both critical for vehicle electrification) from tailings that incorporates partial neutralization and iron removal in the bioleaching circuit; bench- and pilot-scale tests have resulted in excellent nickel and cobalt recovery over a range of temperatures.  However, this process generates a new bioleach residue, which is heavier and more voluminous than the original tailings due to pyrrhotite oxidation and jarosite formation during the bioleaching process. This residue can be problematic for long-term disposal. A possible solution being studied for this issue is using mine backfill as a disposal mechanism.  Underground backfilling allows for effective re-purposing of mine waste, however the backfill must also be able to withstand a certain load, since in most cases it is used as an underground construction material, such as in cut-and-fill mining methods.  Therefore, the composition of the mill tailings must be such that when combined with a binding agent and pumped underground, the slurry or paste is then able to withstand a certain load within a certain period of time.  Unfortunately, high-pyrrhotite content tailings, commonly found on mine sites in Ontario and Quebec, are reactive and can easily oxidize and produce acidity and/or metal-laden drainage under some disposal conditions. This means that the pyrrhotite in the tailings can lead to acid mine drainage if stored on surface, however, it can also cause strength degradation if re-purposed in too high a concentration in underground mine backfill.  The research being done at CanmetMINING related to the bioleaching process is aimed not only at recovering nickel and cobalt from mine tailings, it is also being used in an attempt to neutralize the tailings to reduce acid mine drainage and backfill strength degradation. This paper reports on research designed to evaluate different options for transforming the bioleaching process residue into iron oxide phases, for better environmental footprints if stored on surface, as well as increased disposal possible, if re-purposed as underground mine backfill material.  

May 4, 2025

By P. J. Oakley, W. M. Thomas, S. W. Kallee, D. G. Staines

A Friction stir welding (FSW) is now extensively used in aluminium industries for joining and material processing applications. The (FSW) technology has gained increasing interest and importance since its invention at TWI almost 15 years ago. The basic principle, recent applications and the continuing development of the FSW technology are described. The paper will introduce some of the variants of FSW, such as Dual-rotation, Twin-stir(TM), and the Stir-lock(TM) technique.

Jan 1, 2006

By G. Lafont

Aug 1, 2013

By Min-Sung Kang

Excavation and earthmoving equipment mostly operate in accident-prone areas. These areas normally have rollover, confinement, and fall or may be considered harmful work areas due to demolitions and sewage removals. It is inevitable that excavation and earthmoving systems should be developed to secure the safety of operators through unmanned and remote control systems. Therefore, this research proposes a system that enables excavators to be unmanned and remote controlled without any renovation, remodeling, change, or transformation by applying attachable and separable mechanism and modules. Moreover, this research proposes the sensor module to evaluate the dynamic status without processing remodeling or transformation the existing hydraulic drive excavation system by adopting the easy attachable and separable mechanism. The study verifies this proposal based on observed possibility and feasibility through the experiments.

Aug 1, 2013

By G. F. Miller

ONLY IN THE Province of Saskatchewan is natural sodium sulphate found in Canada in amounts large enough to make recovery economically sound. Geologists have estimated that the numerous deposits within the Province contain upwards of 200 million tons of Glauber's salt. There are twenty-one deposits in the Province which contain 500,-000 or more tons and about two dozen with lesser amounts. The first recorded production of sodium sulphate in Saskatchewan was in 1918. The company concerned, and others that attempted to develop the industry in its early stages, were unsuccessful. Their failures were caused by two main factors -lack of knowledge of efficient operating methods and the unstable market situation for the finished product. Today, the situation is changed in both respects and the product, commonly referred to as 'saltcake", is a very important chemical requirement of many industries throughout the world. Before proceeding with remarks on manufacturing methods it should be stated that, although this is a general paper on the manufacturing methods and end uses of the saltcake produced in the Province, the writer is, of course, more familiar with the plants operated by Saskatchewan Minerals than with other operations and perhaps may be excused for dealing more particularly with the plants of that Compa11y.

Jan 1, 1958

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

By J. Fixter, P. Prangnell, Z. Pinter, E. Eimer, B. Chehab

"High deposition rate Wire and Arc Additive Manufacture (WAAM) can provide benefits to the aerospace industry, including a reduction in lead time, reduced material waste and, through higher solidification rates, refinement of the as-built microstructure relative to a cast material. However, candidate 2xxx series high strength alloys for this process normally require a solution treatment, which is problematic for large near-net-shape components, and age hardening to achieve maximum mechanical properties. With each layer being subject to multiple thermal cycles, exploiting the thermal conditions in the WAAM process to avoid post-build solution treatment is therefore of interest. A solutionisation model has been developed for the WAAM process, based on diffusion controlled dissolution using DICTRA, which was validated through thermal simulations combined with 2D and 3D image analysis. The model has subsequently been used to simulate the solutionisation behavior during a typical WAAM thermal cycle and to explore what could theoretically be achieved by, for example, refining the starting microstructure.INTRODUCTION There is currently great interest in exploiting additive manufacturing (AM) in the aerospace sector due to several benefits it can potentially provide; including reduced material waste, shorter product lead times and greater design freedom (Herzog, Seyda, Wycisk, & Emmelmann, 2016). However, with aluminium alloys the material properties obtained are generally inferior to those of conventional high-strength wrought products; therefore more research is required to explore the potential for exploiting the unique process conditions in AM to improve the as-deposited microstructure. A range of AM techniques are now available (Debroy et al., 2018), which differ in terms of the feedstock type and power source and it is necessary to match the appropriate technology to a particular application. This generally requires a compromise between the build rate and shape resolution. Wire and plasma-arc additive manufacturing involves using an electric arc to melt wire onto a substrate, and fabricates a part by building up overlapping layers of deposited weld beads (Addison et al., 2015; Williams et al., 2015). The benefits of this process over other AM methods are the much higher deposition rates (e.g. kg’s/hour) achievable and lower capital equipment costs relative to powder bed techniques, which makes it suitable for large scale applications. However, limitations include a lower part complexity, lower solidification rates and a greater need for post-process machining (Frazier, 2014)."

Jan 1, 2018

By W. Blum

Progress made in improving the creep resistance of Mg alloys is reviewed with the emphasis on microstructural interpretation. Experimental results on the increase of creep strain with time at constant stress a measured for limited times and strains are displayed in a transparent form as creep rate-strain diagrams from which the minimum creep rate stress is safely derived. In addition, data on the thermal stress component a derived from high-precision a-reduction tests are reported. Within a simple statistical dislocation model these data allow one to quantify the relation between dislocation velocity v and a . In combination with structure evolution laws this relation serves as a basis for modeling the creep rate. New alloys have distinctly higher creep resistance than AZ91 where precipitation hardening plays a minor role. This is due to hardening by intermetallic phases which may form a continuous skeleton along the grain boundaries (e.g. Ca-alloyed AZ91) and/or submicron-sized precipitates within the grains (MRI230D, Mg-Zn-Ca alloys).

Jan 1, 2006

By L. Xia, B. Hart, J. Nigim, Z. Chen

"Grinding ore is an important step in the flotation process. Not only does grinding reduce particle size and liberate minerals, it also creates conditions for reactions to occur on particle surfaces that can aide or inhibit flotation. There have been numerous studies examining various grinding regiments and the effect on flotation pulp chemistry, including autogenous grinding and using media of variable composition. There have been however, few studies looking at the effect of variability in grinding media size on pulp chemistry and subsequent flotation. This study attempts to link changes in pulp chemistry in response to variations in grinding media size to flotation recovery. It uses probes mounted in the grinding chamber (pH, Eh, DO, and conductivity) to monitor pulp chemistry changes during grinding of a Cu-Zn ore. Surface chemistry analysis by ToF-SIMS was performed on sphalerite from the mill discharge. Activator and depressant species were monitored on the mineral surfaces and their presence was evaluated in the context of variability in pulp chemistry linked to differences in grinding media and its ball size.INTRODUCTIONIt has been widely recognised that not only does grinding reduce particle size and liberate minerals but the grinding environment has a large effect on the flotation of sulphide minerals. This effect is attributed to Eh change, iron hydroxide coating on surfaces, oxygen reduction, precipitation from solution and galvanic coupling (Grano, 2009). As early as 1960, it was reported that after grinding the ores in an iron mill the natural floatability of sphalerite was reduced significantly (Rey and Formanek, 1960). Kocabag and Smith (1985) studied on the industrial circuits showing that the depression of sulphides flotation in a steel mill is possibly due to the coating of iron oxidation products. Peng, Grano, Fornasiero, and Ralston (2003a, 2003b) found that iron contamination from grinding media plays a dominant role in depressing galena and chalcopyrite flotation. Huang, Grano, and Skinner (2006) reported the same observation in the flotation of arsenopyrite."

Jan 1, 2016

By W. A. MacWilliams, R. G. Reynolds

"This paper describes, for the first time, a patented method of extracting sodium sulphate from a natural deposit in Western Canada. The method resembles, but is not, strictly speaking, solution mining. The fact that a plant based on this method has been in successful operation since late 1969 will be of added interest. The deposit in question is located near Metiskow, Alberta, and conventional surface recovery methods could not be applied because of heavy concentrations of mud. Considerable pilot work went into the separation and recovery process on which the plant operation is based. The history of the industry is covered briefly as background to this development. Today it is clear that the method has broader application within the industry and, in concept, may generate interest in many other applications."

Jan 1, 1973