Search Documents

By D. Kalumba, S. Jjuuko

"Thin Spray-on Liners resist relative small deformations (< 1 mm) between rock blocks or fragments in terms of a combination of shear, adhesive and tensile-bond strengths. Shear-bond strength addresses the ability of a thin liner to resist stresses that act parallel to the rock-liner interface. Therefore quantification of shear-bond strength is essential in the formulation of design standards and requirements for Thin Spray-on Liners. In this paper Thin Spray-on Liner support mechanisms are reviewed. In addition previous methods of Thin Spray-on Liner shear-bond testing are discussed. The paper also explains the research being carried out at the University of Cape Town to investigate the effect of different parameters on the shear-bond strength.INTRODUCTIONRock surface support is widely used to combat rockfalls and resulting injuries and fatalities in the vicinity of active faces (Potvin, 2002), where workers spend most of their time (Adams & Baker, 2002; Potvin, 2002; Lacerda, 2004). The conventional (traditional) surface support systems in underground rock support include passive methods such as mesh and lacing and active methods such as shotcrete. However, rockfall sources between 1990 and 2000 in Nevada gold mines showed a steady increase in rockfall injury associated with mesh support as shown in Figure 1 (Lacerda, 2004). The conventional methods also negatively impact the mining operations with regards to costs, logistics and mining cycle times due to large material volumes (Tannant, 2001; Ozturk & Tannant, 2010; Ferreira, 2012). Therefore, these systems need to be substituted, with enhanced methods, in order to realize the business target of the mining industry of providing the planned return on investment made without harm and within budget."

Jan 1, 2015

By H. W. Little

INTRODUCTION MINERAL deposits of Salmo map-area (Figure 1) have aroused the interest of prospectors for more than a half-century. Properties within the map-area have produced lead, zinc, silver, tungsten, and gold. Sheep Creek mining camp ranks fifth in the Province in the total production of gold, but during recent years interest has been concentrated upon base metals, and meticulous prospecting and exploration have resulted in the discovery of many large zinc-lead orebodies. PREVIOUS WORK Geological investigations of the region were begun long ago, and it is interesting to trace the development of ideas with our increasing knowledge of the geology of this complex area. The first geological examination of the rocks of Salmo map-area was made in 1859-60 by H. Bauerman (1), who was employed as geologist accompanying the first international Boundary Survey. Bauerman examined the rocks exposed along Pend d&apos;Oreille river and published a section indicating that the sedimentary rocks are probably of Palaeozoic age, and are intruded by granite of unknown age. McConnell and Brock(2), in 1894 - 1900, carried out the reconnaissance mapping of the West Kootenay Sheet, on which they outlined the Mesozoic rocks of the Rossland Beaver Mountain volcanic groups that they believed rested unconformably upon the sedimentary rocks to the southeast, which they regarded as of Palaeozoic age.

Jan 1, 1951

By D. E. Gill, A. Piche, S. Dufresne

"SOMMAIREUne méthodologie de prévision des coûuts de forage en galeries est proposée. Cette méthodologie a été élaborée pour les perforatrices pneumatiques manuelles. Elle est composée de quatre modèles: (1) un modèle de pénétration conduisant à la prévision du temps de forage; (2) un modèle d&apos;estimation de la durée de vie des fournitures; (3) un modèle d&apos;estimation de fa quantité d&apos;énergie consommée; et (4) un modèle de calcul de couts. Elle fait intervenir la résistance en compression uniaxiale de la roche du massif foré, le diamètre des trous, Ie type de perforatrice utilise, fa pression d&apos;air d&apos;opération, la longueur des fleurets, les temps morts associes au forage ainsi que le rendement des compresseurs, des perforatrices et du réseau de distribution de l’air comprime. L &apos;application de la méthodologie est illustrée à l’&apos;aide d&apos;un exemple, suivi d&apos;une courte analyse de sensibilité et d&apos;une brève discussion. ABSTRACTA drilling cost estimation methodology for underground headings is described. This methodology has been developed for percussive hand-held drills. It comprises four models: (1) a drillability model used for the prediction of the drilling period; (2) a model for the prediction of bit and rod lives; (3) an energy model; and (4) a cost model. It makes use of the uniaxial compressive strength ofthe rock drilled, hole diameter, drill type used, operating air pressure, drilling rod length, dead times that may occur during the drilling operation as well as compressor, air distribution network and drilling machine efficiencies. The application of the methodology is illustrated with an example, followed by a short sensitivity analysis and brief discussion."

Jan 1, 1994

By William M. Luff

"The Bathurst area has recorded mining production as early as 1837, although the bulk of the production has come in recent years. Production has been mainly from the well-known massive sulphide deposits, but vein, gossan, and a variety of other deposits have also been mined. This paper summarizes the history of the mined deposits, along with tonnages and grades produced. A number of ""firsts"" have been noted in the Bathurst area. The A Zone deposit, located in the Heath Steele area, was the first in the world discovered using airborne electromagnetic methods. Heap leaching of gold from the gossan zone at Caribou was the first operation of its kind in Canada. The Keymet mine was the first base metal (lead-zinc) mine in New Brunswick. For the past few years, the Brunswick No. 12 mine has been one of the largest zinc mines in the world.IntroductionThe Bathurst area (Fig. 1) first had mining production in 1837 when copper was mined from a deposit on the Nepisiquit river (MacKenzie, 1958). The majority of the production, however, has been in recent years from massive sulphide deposits, but there are also other significant operations. . Table 1 is a summary of Bathurst area mineral production, showing concentrator feed tonnages and mill feed grades. The table does not include peat deposits, sand and gravel, dimension stone or rock quarries. Figure I is a general geology map of the Bathurst area, indicating deposit locations. The deposits are divided into four categories: massive sulphide, vein, gossan and other. The deposits in each category are described in chronological order of exploitation."

Jan 1, 1995

By H. Nakano

The codeposition behavior of impurities such as Ag, Bi, Fe, Ni, Pb and Sb with Cu was investigated galvanostatically at 5-3000 A/m2 using a Pt cathode at 60 °C in acidic copper (I) chloride (cuprous chloride) solution at pH1-2 containing 1.0 mol/L of Cu+ and 4.9 mol/L of Cl-. The impurities were classified into two groups: Group I (Ag, Bi) which codeposits with Cu as a metal, and Group II (Fe, Ni, Pb, Sb) which is slightly involved in the deposited Cu in nonmetal form from the electrolyte. Silver and Bi in Group I behaved as more noble metals than Cu, and significantly codeposited with Cu, showing typical features of regular-type codeposition. When Cu was deposited dendritically, the Ag and Bi content in the deposit increased with increased duration of electrolysis as a result of decreased net current density caused by increased cathode area. The current efficiency for Cu deposition in impurity-free solution was 95-100% over 100-1000 A/m2, but it abruptly decreased at above 1000 A/m2 when the limiting current density of Cu was attained. Although Fe, Ni, Pb and Sb in Group II were involved to 0.01-0.02 mass% in the deposit, they had no influence on the current efficiency or morphology of Cu.

Jan 1, 2007

By T. T. Chen

A detailed mineralogical study was carried out to characterize the products generated in a conventional copper refinery anode slimes treatment circuit. The anode slimes, which are first leached in sulphuric acid media under an oxygen pressure to dissolve the copper and much of the tellurium, were found to contain various Ag-Cu selenides, PbSO4, Ag, Au and BaSO4. The resulting Ag2Se, Ag3AuSe2, Se, Au, PbSO4, BaSO4, SnO2 and silicate-rich leach residue is dried and pelletized. It is subsequently roasted to convert the selenium to Ag2SeO3, volatile SeO2 and water soluble Na2SeO4. The roasted product, which was found to consist of Ag2Se, PbSe, PbSO4, BaSO4, Ag3AuSe2, Au and Sn02, is smelted and refined in a Dore furnace to produce a Dore metal that contains a (Ag,Au,Pd,Cu,Pt) alloy together with traces of CuO and a Cu-Pb oxide phase. Parting plant mud shown to contain AgC1, Ag, Au, (Au,Ag,Pd), Ag2Cu2O3 and Ag20, and scrubber mud containing PbSO4 and AgC1 are also fed to the Dore furnace. The Dore furnace sequentially separates a silica slag which was found to consist of Ag, Sn02, BaSO4, Pb-Sb oxide, Fe-Sb-Ni-Cr oxide and a Pb-rich silicate phase, a soda-rich slag containing Na2CO3.H2O and Na2(Se,Te)03, and a niter slag containing Na2TeO3, Na2(Se,Te)03 and a Na-Te-Se-Pb-Ba-Cu oxide phase. The Dore metal is electrorefined in Moebius cells to yield high-purity silver and a gold mud which was shown to consist of a (Au,Ag,Pd,Cu,Pt) alloy and traces of CuO. Silver is leached from the gold mud and the resulting gold sand is cast into anodes and electrorefined in Wohlwill cells to produce pure gold.

Jan 1, 2007

"Eastern Canadian thermal coal mined at Minto, New Brunswick, and in western Cape Breton at St. Rose, Inverness County, Nova Scotia, contains 6-8 per cent sulphur. Both coals are high volatile bituminous. types. The Minto coal averages 18 per cent ash, 7 per cent sulphur and has a Btu rating of 11,900 per lb. Pyritic sulphur accounts for 75 per cent of the total sulphur and the remainder is largely organic; the amount of sulphate sulphur is negligible. This means that in a 7 per cent sulphur coal, 2 per cent is organic and 5 per cent pyritic sulphur. Pit-head St. Rose coal contains approximately 10 per cent ash, 7 per cent sulphur and 11 ,800 Btu/lb. The distribution of sulphur is different to that of Minto coal because about 12 per cent sulphate sulphur is present. Thus, a 7 per cent sulphur coal would contain 4 per cent pyritic, 2 per cent organic and 1 per cent sulphate sulphur.The iron sulphides, pyrite and, to a lesser extent, marcassite occur over a wide size range from large sulphur balls to crack fillings, lenses, and individual crystals and framboids. Coarse-grained pyrite and sulphur balls are easily separated during washing. It is the fine grain sizes, intimately mixed with the coal constituents, that are difficult to separate. Quantimet analyses of the fine grains in coal from both localities showed that about 50 per cent were smaller than 30 micron(1).No efforts have been made to wash the Inverness coal of Nova Scotia and in 1980 washing ceased in New Brunswick. Previously, the Minto coal was processed in an antiquated jig circuit which reduced ash from the strip operation run-of-mine value of more than 20 per cent to less than 18. More effective removal of ash and sulphur could clearly be obtained. Laboratory tests on both Minto and St. Rose coal have shown that ash rejection rates of 40 to 50 per cent at yields of 70-80 per cent were possible(2), Little information on sulphur removal was available."

Jan 1, 1981

By G. D. Hibbard

New regions of material property space can be accessed by combining microstructural design at the nm-scale with architectural design at the µm- or mm-scale. In the first case, large strength increases associated with grain size reduction to below 50 nm have driven extensive research efforts into the development of nanocrystalline materials [e.g. 1-3]. For many potential structural applications, however, the density of a nanocrystalline material is just as important as its strength. In fact, reducing the density is more important than increasing the strength for certain weight specific materials performance indices, and it is especially critical for applying structural nanomaterials in the aerospace and automotive sectors. We have developed a new type of structural nanomaterial wherein the effective density of the parent metal is reduced by more than an order of magnitude by incorporating an internal periodic cellular architecture of open space. In one example a low density cellular nanocrystalline material was created by electroforming nanocrystalline Ni around a rapid-prototyped acrylic photopolymer microtruss, Figure 1 [4]. Microtruss materials have periodic cellular architectures that are specifically designed to undergo stretching-dominated deformation as opposed to the bending-dominated deformation in conventional open cell metal foams [5,6]. This new cellular nanocrystalline hybrid material combined the structural efficiency of microtruss architectures with the ultra-high strength that can be achieved by grain size reduction to the nm-scale. Although it played a critical role as a cathode support during the initial stages of nanocrystalline electrodeposition, the polymer core did not contribute significantly to the inelastic buckling resistance of the composite metal/polymer struts and it may therefore be desirable to remove it post deposition by means of chemical dissolution or thermal decomposition [4]. Nanocrystalline electrodeposition can also be used to reinforce conventional cellular metals (Figure 2), creating new types of cellular composites such as metal/metal microtruss hybrids [7-10] and metal/metal foam hybrids [11,12]. For example, nanocrystalline Ni-Fe alloy sleeve thicknesses of up to 400 µm were used to reinforce an aluminum alloy microtruss that had been fabricated using a stretch-bend approach; the nanocrystalline sleeves had the effect of increasing the microtruss strength by up to a factor of twelve and the specific strength by a factor of three [8]. Alternatively, much thinner sleeves can be electroplated to produce structural coatings. In one example, a nanocrystalline Ni coating was designed to provide both corrosion protection and inelastic buckling resistance [10]. Because the ultra-high strength material was optimally located at the furthest distance from the neutral bending axis, only a thin coating of 50 µm was needed to double the inelastic buckling resistance of the 1.13 mm x 0.63 mm cross-section plain carbon steel struts [10]. Overall, the mechanical performance increase that can be obtained through electrodeposition depends on a complex interaction between the starting cellular architecture and the nanocrystalline sleeves.

Jan 1, 2010

By Donald Lindell

Safety Share ?Dad receives fryer for Christmas 2009 and makes delicious sweet potato fries ?When the oil fryer was pushed back on the stove for cooling, the back edge comes into contact with the stove top controls, unknowingly activating the cooking element, family leaves kitchen. ?Faint smell of smoke from the melting plastic alerted the family; teenager arrives first and pulls the fryer forward causing oil to spill onto hot stove and burst into flames that reach the microwave ?Teen runs for sink to grab pan of water but is stopped by Dad ?Dad opens refrigerator, grabs baking soda and pours it on fire, extinguishing flames Lessons 1.DO NOT USE WATER ON GREASE FIRE 2.Where is the baking soda in your kitchen?

May 1, 2010

By Richard Hurteau

Design and validation of an integrated guidance system for articulated ground vehicles is investigated. The development of an autonomous industrial vehicle must take into the account the specific geometry of these vehicles; they can be composed of a tractor with 1 or 2 trailers or of articulated type like LHD. Moreover the tractor-trailers type vehicles can have on-axle hitch configuration or positive/negative off axle configuration. The path-tracking of a tractor-trailer vehicle in restricted space is presented and discussed in this paper. Recent results obtained in simulation and validated by experimentation are also presented. These studies can lead to better ways of maneuvering an articulated vehicle in a restricted space or automatically executing of docking and parking maneuvers

May 1, 2002

By Vincent Jourdain

Located in the James Bay Territory of Quebec (figure 1), the Clearwater property is jointly owned by SOQUEM Inc. and Eastmain Resources Inc. Exploration on the property since the early 70&apos;s has resulted in the discovery of several gold showings. Exploration work by the joint venture since 1995 has led to the definition of the Eau Claire Zone containing an indicated resource of 540 000 tonnes grading 11.1 g/t Au (8.7 g/t Au cut at 34.28 g/t Au). Hosted by the archean Eastmain Greenstone Belt, the property geology is dominated by mafic volcanics containing thin horizons of felsic volcanics and/or sedimentary rocks (figure 2). The sequence is metamorphosed to the amphibolite facies and contains two small toalitic intrusions. Regionally, the structural trend is oriented E-W but in the area of the Eau Claire Zone a second trend oriented NE-SW is also present. The first exploration work on the property was conducted by SEREM and SDBJ from 1973 to 1976. It consisted of an airborne electromagnetic survey and a ground follow-up program on several grids. This program, comprising geological mapping, geophysics and drilling, led to the discovery of the Natel showing where a drill intersection returned 8.89 g/t Au over 2.65 m. From 1978 to 1985 the area was withdrawn from staking because of the hydroelectric projects of the James Bay. In 1985, Westmin Resources Limited and Eastmain Resources began an exploration program based on a helicopterborne electromagnetic survey. Once again, a ground follow-up program was conducted on several grids. This program included a soil geochemical survey that identified a strong (up to 10 g/t) gold anomaly. Drilling of the anomaly led to the discovery of the Eau Claire Zone where resources were estimated at 270 000 tonnes grading 6.1 g/t Au at the end of 1990. In 1995, SOQUEM Inc. took an option to gain a 50% interest on the property and obtained its interest in 1998. Since 1995, two principal mineralization zones were identified on the property. The "Rosemary Zone" consists of veinlets and disseminations of pyrite and chalcopyrite within a magnetite-rich amphibolite. The mineralized zone was identified by stripping within an area of 1000 by 500 metres. Drilling indicates copper grades up to 0.32 % Cu over 49.2 m. with locally grades of 0.75 % Cu over 5.9 m. The mineralised zone is associated with QFP dykes and corresponds to a strong magnetic anomaly and a strong copper and molybdenum soil anomaly. The "Eau Claire Zone" consists principally of a set of gold bearing quartz-tourmaline veins oriented E-W and dipping at 45-50??to the south (figure 3). More than ten different veins are recognised in the zone and up to eight veins were observed in a single trench (figure 4). The host rock between the veins shows a degree of deformation similar to the regional volcanosedimentary rocks. Each vein is hosted by a unit of actinolite-tourmaline-biotite schist up to one meter thick. The veins and their hosting schist clearly cross-cut the schistosity of the hosting lithologies and the contacts between amphibolites and felsic to intermediate rocks. Usually, the veins are less than a meter thick and are composed of quartz, tourmaline and calcite. The proportion of quartz and tourmaline varies from 0 to 80% within a single vein. The veins commonly show massive, banded or brecciated texture. Sulphides, mainly pyrite, pyrrhotite and chalcopyrite, generally form less than 5% of the vein material.

May 1, 2001

By F. Rojas, M. Sanchez, J. Palacios, O. Pavez

Copper sulfide is the main mining resources in Chile, and most of this metal is obtained via pyrometallurgical extraction in seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country. In 2002, 1,522,000 metric tons of fine copper were produced, with a notorious environmental impact due to the large amount of slag generated, including transportation and disposing problems. Therefore, there is a great interest in finding alternative uses in order to give additional value to the slag. This is a total project development concept, which consider residues as new resources where new components could be obtained, improving sustainability in mining activities and also ensuring clean production processes. Thus, the present work shows a review of copper slag characterization as well as several ways of utilization, including compact material for road and railway installation, part of admixtures in concrete.

Jan 1, 2004

By C. S. Touchard, F. Bourgeois, L. Cassayre, Julcour-Lebigue C.

Developing a hydrometallurgical process that can overcome the refractory nature of chalcopyrite (CuFeS2) to leaching still eludes the minerals industry, despite major research efforts spanning decades. The several leaching experiments of this ore in sulfuric acid tend toward the same conclusion that the precipitation of elemental sulfur or iron containing species are the main dissolution inhibitors. Describing both the electrolyte composition and the various solid phases in equilibrium for the Fe-H2SO4-H2O system is essential to overcome this issue and to find an operating window. According to the thermodynamic models and to the thermodynamic data, we demonstrate, in this study, the need to use the Specific ion Interactive Theory (SIT) model to describe complex electrolytic systems through a limited number of parameters. Hence, the binary interactions for our case study have to be defined and estimated. This work develops a methodology to determine these parameters of the SIT model up to 90°C and an acid concentration of 1 mol/kg from published data for H2SO4-H2O and Fe(II)-H2SO4-H2O sub-systems or from new experimental data for the Fe(III)-H2SO4-H2O one. This method will eventually be applied to copper systems to lead to a thermodynamic description of the complete CuFeS2-H2SO4-H2O system. INTRODUCTION A leaching process consists in the dissolution of a solid phase into an aqueous medium in order to extract compounds of interest. It is a key step in the hydrometallurgical processes used in the primary production and recycling of metal components. One of the main leaching issues is the formation of passivating layers on the surface of solid particles, whose consequence is a partial or total hindrance of the dissolution. The leaching of chalcopyrite (CuFeS2) in sulfuric acid is a prime example. No industrial solution for the atmospheric pressure leaching of this ore has been developed to date because of passivation phenomena caused by the formation of elemental sulfur or iron-containing precipitates on the surface of the particles (Li, Kawashima, Li, Chandra, & Gerson, 2013). In the 1970s, the Pourbaix diagrams established for the Cu-Fe-S-H2O system at 25°C for low concentrated solutions (Garrels & Christ, 1965; Peters, 1976) agreed that copper and iron are fully dissolved at high potential and in acidic medium (pH < 4). However, they neglected the many stable solid phases that can form in these conditions. In addition, the Pourbaix diagrams of chalcopyrite in water, calculated with two recent databases (FactPS and Thermoddem 2017) associated to FactSage and PhreeqC softwares respectively, show large discrepancies at 75°C (Figure 1). Indeed, at high potential, FactSage predicts the formation of goethite FeOOH at a pH value of 1, while PhreeqC predicts the formation of jarosite (H3O)[Fe3(SO4)2(OH)6] for pH greater than 2.5.

Jan 1, 2019

The primary arsenic minerals in the uranium ore processed at the McClean Lake Operation are rammelsbergite, niccolite and gersdorffite. During processing, a large fraction (80 - 95%) of these reduced minerals is oxidized and dissolves primarily as As5+ in the leachate solution. In the tailings preparation circuit the dissolved As5+ is precipitated as a poorly crystalline form of the mineral scorodite. Following subaqueous deposition in the tailings management facility, a temporal rise and fall in arsenic pore water concentrations has been observed. This is due to the oxidation of the residual quantities of reduced arsenic minerals initially present in the tailings sediment. The XANES (x-ray absorption near edge spectrometry) technique has shown that the As1- is gradually oxidized to As3+ and then finally As5+ in the tailings sediment. This oxidation process results in a temporary accumulation of As3+ in solution and is the source of the rise and fall in arsenic concentration observed.

Aug 1, 2010

By G. E. Agar, W. B. Kipkie

"This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady state balance can be calculated for a circuit.Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative tec1nique to arrive at the steady state balance. The program is written so that a variety of circuits can readily be simulated.A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets is presented on sulfide ores, on copper-nickel separation and on silver flotation,"

Jan 1, 1978

By Arthur Brant

STEEPROCK LAKE (Figure 1) lies about two miles north of Atikokan, a village approximately one hundred and forty miles west of Fort William and one hundred miles east of Fort Frances on the Canadian National railway. The possible presence of hematite beneath the waters of Middle arm was inferred by early geological investigators (1890-1903) from the dense hematite float found on the southerly shores of this portion of the lake (1). A dip-needle survey of Middle arm, undertaken in the winter of 1930-31 by J. G. Cross, indicated two areas of high magnetic attraction which Mr. Cross thought might be due to magnetic iron oxides associated with possible hematite bodies. Bedrock could not be reached by the ineffectual hand-drilling so courageously attempted, and further work was abandoned. It was not until 1937 that Mr. Jos. Errington, of Toronto, convinced of the possibilities, determined to support Mr. Cross to the extent of several thousand feet of drilling. During the winter of 1937-38, holes Nos. 1, 3, 4, 5, and 13 were put down (see Figure 1). The first four of these holes demonstrated that the areas of magnetic attraction outlined by the dip-needle survey east of the Narrows and southwest of Elbow point were due to ash rock (2). As a result, Mr. Cross decided to investigate the bordering areas of low magnetic attraction and selected a location near the high ferruginous lime (3) point in the northeast of Middle arm. Dense, hard hematite beneath approximately 350 feet of water and clay was struck in the first hole, and, before the end of the winter&apos;s drilling, hematite had been encountered in holes Nos. 6 to 13 along a straight line 700 feet in length (see Figure 1). In the meantime, the Steerola ( 4) Exploration Company had been formed to continue development and already, in the spring of 1938, W. D. Neeland, the Company geologist, had come to the conclusion that the most probable location for possible hematite was at the ash-lime contact. Accordingly, during the summer, drilling was continued off-shore in holes Nos. 15, 25, and 27 (see Figure 2) toward possible hematite bodies inferred by Mr. Neeland.

Jan 1, 1940

By W. L. Brown

"The properties of Base Metal Mining Corporation are in Yoho Park about 2 1/2 miles northeast of Field; British Columbia; on the main line of the Canadian Pacific railway. There are actually two mines; the Monarch on mount Stephen and the Kicking Horse on mount Field; separated by the steep valley of Kicking Horse river. The outcrops of the orebodies range from 4; 900 feet to 5; 300 feet above sea-level. The concentrator is situated below the Monarch mine and is connected to the main portal by an aerial tramway. The ore from the Kicking Horse mine is conveyed by aerial tramway to a storage bin on the main highway and is then trucked to the concentrator.During the construction of the Canadian Pacific railway through Kicking Horse valley, galena float was found at the base of mount Stephen. The East Monarch outcrop was staked in 1894. The outcrop of the West Monarch ore body on the cliff face of mount Stephen was not discovered until 1916. The Kicking Horse orebodies on mount Field were discovered a few years later. In 1912, a 75-ton concentrator was erected, which operated at intervals until 1924. During this period approximately 42,000 tons were mined and milled, largely from the East Monarch orebody. In 1928, the Base Metal Mining Corporation, Limited, was formed to take over the Monarch and Kicking Horse mines. A 300-ton differential flotation concentrator was erected and production started in the autumn of 1929. In a very short time, however, the low price of metals forced the mill to shut down until August 1933. From 1929 to 1935, when the mill again ceased operation, a total of 256,500 dry tons of ore, averaging 1.59 oz. silver per ton, 9.7 per cent lead, and 12.6 per cent zinc, was mined and milled, largely from the West Monarch orebody. After a period of further underground development, the concentrator reopened in 1940 and is still in operation. From 1940 to the end of 1944, 354,363 tons of ore was milled, averaging 5.32 per cent lead and 10.47 per cent zinc."

Jan 1, 1954

By M. R. Babcock

"The Rabbit Lake story began in the late sixties and will continue well into the twenty-first century. It is a story of success, of multiple ore body discoveries, of unique systems, and new methods made possible through innovative and state-of-the-art design. Two quite different geological systems host the five ore bodies mined, or slated to be mined. These two systems have yielded two distinct ore types, each with characteristic mineralogical properties and each requiring its own specific mill circuit.Emphasis on communications and our unique systems have led to a satisfactory and fulfilling work environment resulting in the historically low employee turnover which has contributed to the operation success.A comprehensive environmental study after twelve years of operation has given the Rabbit Lake Operation a completely clean bill of health. INTRODUCTIONRabbit Lake can be described as Saskatchewan&apos;s first highgrade uranium mining operation, which set the stage for the province&apos;s current role as the leader in uranium mining throughout the western world. The importance of the Rabbit Lake operations - past, present and future.LocationThe Rabbit Lake operation is located in northeastern Saskatchewan (Fig. 1)- 805 km north of Saskatoon, Saskatchewan, and 814 km northeast of Edmonton, Alberta. OwnershipGulf Minerals Canada Limited discovered the Rabbit Lake deposit in 1968. Mining operations began in 1975and were operated by Gulf until purchased by Eldorado Nuclear Limited in 1982. In 1988, Eldorado merged with Saskatchewan Mining Development Corporation (SMDC) to form Cameco-A Canadian Mining &. Energy Corporation. The new corporation is one of the world &apos;s largest uranium companies.Cameco&apos;s $1.5 billion in assets include the Rabbit Lake uranium mine (Cameco 100010); the Key Lake uranium mine (Cameco 66.67%; Uranerz Exploration and Mining Limited 33.33%); the Cluff Lake uranium mine (Cameco 20%; Amok Ltd. 80%); the Fuel Services Division at Blind River and Port Hope, Ontario (Cameco 100%); and a 100%); and a 48.75% interest in the Cigar Lake uranium deposit which is now at the test mining stage (Cogema Canada Ltd . 32.625% ; Idemitsu Uranium Exploration Canada Limited 12.875%; Corono Grande 3.75%; Korea Electric Power Corporation 2%). In addition, Cameco is involved in a number of base and precious metal explor ation projects."

Jan 1, 1989

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By J. X. Guo, A. Pindred, J. Moore

"Two modified centrifugal flotation cells (CFC), Q2 and Q3 models, have been developed for froth flotation. The operating mechanism of Q2 uses a rotating bowl to create a centrifugal force on the feeding slurry. Froth concentrate is collected on the central top of the cell and tailing is discharged along the top edge of the rotating bowl. The Q3 utilizes a vertical rotating feed pipe to introduce the feed slurry into a stationary flotation column cell. A centrifugal force is also created by a rotating pipe for the feeding slurry. Froth concentrate floats over the cell and tailing discharges through the bottom of the cell. The centrifugal force causes the flotation recovery of fine particles from CFC to be higher than from the conventional cell. The major operating variables of CFC are the rotating speed, air flow rate into feed slurry, and slurry feeding rate etc. Flotation tests have been carried out on synthetic mixtures of galena-silica and chalcopyrite-silica, as well as some natural base metal ore samples. Parallel tests were also conducted on a conventional flotation cell. The comparative test results demonstrated that both Q2 and Q3 have the advantage of higher recovery of finer than 10 µm mineral particles, which are very difficult for the conventional non-centrifugal flotation cell to recover. The grade-recovery curves produced from CFC are equivalent to or better than the conventional flotation cell. There is a potential in the future for the CFC to be employed in slime flotation.1. IntroductionA centrifugal flotation cell (CFC) was originally developed by Clean Earth Technologies [I] to separate oil from water and was subsequently applied in froth flotation. Figure 1 illustrates the design of the original CFC, in which a vertical feeding pipe is attached to the center part of a rotating drum and a stationary shell encloses it to direct the float froth and tailing discharge. The slurry flows down to the bottom of the spinning drum, gets in touch with a screen of air bubbles and then migrates outwards under the effect of centrifugal force. After the mineralized froth enters the rotating cell, it is pushed back to the inner surface. The overflowing froth is collected in the froth launder while the tailing slurry is discharged through orifices along the outer rim of the drum."

Jan 1, 1998