Search Documents

By W. B. Boggs

This is a rather comprehensive subject and cannot be thoroughly covered in the short rime allowed for its presentation. This article will touch only upon a few of the chief points of the difficulties encountered in recovering copper from brass shell cases in a primary smelter which was not designed to treat scrap metals. Owing to the fact that the plant is at present (Dec., 1946) closed, and our tests were not completed, full details of the results are not available. As is well known, most primary smelters are situated near the mines in the interior of various countries and are not close to seaports or large industrial and railway centres. Consequently, iris unusual for a primary smelter to be asked to treat scrap metal of any kind. When so required, iris obvious that the primary smelter is at a great disadvantage, for the simple reason that it probably has to pay the freight on the scrap from the seaport or industrial centre to the smelter and then also pay the freight on the recoverable metal from the smelter to the refinery, or seaport or industrial centre. Another disadvantage is that a primary smelter is not equipped to sample and unload the scrap nor bas it usually the equipment adaptable for treating the scrap efficiently, as the plant bas been designed to handle large tonnages of ores and concentrates. This short paper will describe some of our difficulties> and how they were corrected. However, it might be advisable to state briefly some of the methods used in treating brass shell cases in other plants. In the first place, a brass plant producing new brass- especially those producing brass billets for extrusion to make brass tubes or rods, or to be drawn into wire, or making brass cake to roll into brass sheets- generally insists upon using new electrolytic copper and zinc and is opposed to using any scrap or secondary brass . Consequently, such a plant usually will not treat brass shell cases. Therefore, the usual procedure is to ship brass shell cases to a secondary smelter, where it is generally sorted, melted, fire-refined, and returned to the market in the form of a high or low brass ingot which can be sold to brass foundries for making brass castings. This evidently is the cheapest and simplest method. Another method is to ship to a smelter which is a combination of a primary and secondary smelter attached to or near an electrolytic refinery. In plants of both these types, that is a primary smelter with Cottrell dust collectors or a combined primary and secondary smelter with Cottrells or a bag house, the zinc may be wasted. However, if a bag house is used, some of the zinc is recovered, but it is usually contaminated with other metals and further processing is required to recover it.

Jan 1, 1947

By Mohamed Sassi, I. Kolo, R. L. Sousa, R. K. Abu Al-Rub, Manhal Sirat

"Fractures induced by folds are pivotal in hydrocarbon exploration, ground water transport and harnessing of geothermal energy. This is because of the need to predict and understand fracture propagation in reservoirs which have folded rock formations. Despite its prominence, there is a lack of reliable numerical models for simulating fractures resulting from rock folding. This is partially due to the difficulty involved in fracture modelling. As a contribution to fold-fracture modelling, this work applies a coupled plasticity-damage model to rock fracturing and anticlinal folds. Parametric studies on a single folded layer give insight into the fold formation and behaviour. The anisotropic continuum damage model which considers both tension and compression is formulated using the power damage evolution law. For ease in formulation, strain equivalence hypothesis is adopted whereby the strain is the same for both damaged and undamaged configurations. Lubliner plasticity yield criterion is adopted for plastic deformation. The model is coded in Abaqus user subroutine UMAT and is applicable to quasi-brittle materials.INTRODUCTIONThe understanding of fractures in the earth’s crust helps in the prediction, evaluation and characterization of fractured reservoirs, whether they are petroleum, geothermal or underground water reservoirs. This is partly because reservoir permeability and stability are dependent on fracture properties (Nelson, 2001). To achieve this, various approaches have been developed to analyze reservoir rock fractures. These could be grouped into (a) discrete approaches – where the rock mass is represented by a finite number of well-defined components and (b) continuum approaches – where the mathematical assumption of an infinitesimal element is made (Jing, 2003). Ivanova (Ivanova, 1998) comprehensively studied fracture systems in nature and highlighted folds as one of the major geologic settings that produce fractures. Naturally occurring folds in reservoirs sometimes compound fracture analysis. It might not be clear whether the fractures formed before, during or after rock folding. Fractures formed during the folding process are expected to show stress orientations related to folding and are thus of primary concern in rock folding simulation. It could be argued that there are no numerical models that as"

Jan 1, 2015

By R. Chen, K. Xia

In deep mining activities, blasting induced compressive stress wave would be reflected as tensile wave at a free surface around the openings, which would facilitate the tensile failure of the deep rock since it is much weaker in tension than in compression. It is thus critical to understand the dynamic tensile failure of rocks subjected to static tension for deep rock engineering applications. A modified split Hopkinson pressure bar (SHPB) system is adopted to load Brazilian disc (BD) samples statically, and then exert dynamic load to the sample through stress wave generated by impact. The pulse shaper technique is used to generate a slowly rising stress wave and thus to facilitate the stress equilibrium of samples during each test. Five groups of Laurentian granite (with tensile strength of 12.8 MPa) BD samples under the pretension stress of 0 MPa, 2 MPa, 4 MPa, 8 MPa, and 10 MPa are tested under different loading rates. The result shows that the dynamic tensile strength of the rock decreases with the increase of pre-tension stress, which is easy to understand because pre-tension stress weakens the rock sample. It is also observed that under the same pre-tension stress, the dynamic tensile strength increases with the loading rate, revealing the so-called rate dependency that is common for engineering materials. Furthermore, it is found that the loading rate sensitivity of the rock increases with the increase of pre-tension stress. A qualitative explanation for this phenomenon is that more microcracks are generated and activated under higher pretension stress, resulting in a more viscous material. Based on the results, an empirical equation is proposed to fit the data and explain the dynamic tensile behaviour of rock under pre-tension stress. A physical model is used to simulate the dependency of the dynamic tensile strength of rock on the pre-tension stress and the loading rate, which is shown to be in good agreement with the experimental results.

Jan 1, 2015

By A. E. Dyment

In formulating an explosive for any specific set of conditions, various factors must be taken into consideration. Is it to be subjected to water or moisture? .If so, it must be designed to have an inherent ability to resist water. Is it to be used in confined spaces underground, where ventilation is limited? If it is, it must possess qualities enabling it to form, upon explosion, the minimum quantity of noxious gases, such as carbon monoxide or oxides of nitrogen. Is it for use where low temperatures may possibly prevail? If so, it must be capable of resisting such temperatures without freezing. Is it for use where dust or inflammable gases may be present? If it is, then it must be so formulated as to produce, upon detonation, a flame of the lowest possible temperature and the shortest possible duration, in order to lessen the chance of ignition of such gas or dust. This is actually the essential property of a permitted explosive, and it is undoubtedly the most important characteristic of an explosive which is to be used in gassy or closed-light mines. This being the quality that distinguishes permitted explosives from other types, it is interesting to investigate the ways and means by which the low-flame-temperature characteristic is obtained . Generally speaking, such explosives are so designed as to contain comparatively small quantities of nitroglycerin and relatively large quantities of the strength-producing salt, ammonium nitrate. This ingredient does not develop as high a temperature upon explosion as does nitroglycerin, so its presence, in large measure, in place of nitroglycerin results in an explosive which has an inherent low-flame-temperature characteristic, as opposed to one which is .made up largely of nitroglycerin, which would ordinarily be in the high-flame-temperature class. Additions are also made of flame-quenching salts such as sodium chloride, ammonium chloride, and up to a certain limiting percentage of sodium nitrate. These salts, with the exception of the last, do not ordinarily take an active part in the explosive reaction, being present primarily to absorb heat liberated by the reacting ingredients.

Jan 1, 1947

By Feng Tianran, Lu Shijie, Shen Zhengchang, Han Zhibin, Tan Ming

"As a kind of non-metallic material, high-purify quartz sand has been widely used in many fields. Flotation is a popular way to process quartz sand. But it is in difficult position for flotation to get high-purify quartz product due to large amount of coarse particles contained in the feed. In this paper, a design principle of special flotation cell for high-purify quartz sand has been put forward base on ore property analysis and laboratory test, and the pilot scale special flotation cell has been developed to meet the requirement of the quartz sand flotation process. The special flotation cell for high-purify quartz sand is featured by middle positioned impeller, false bottom and draft tube, which could decrease the rising distance of mineralized bubble and strengthen the circulation capacity of the lower part of the flotation cell. Hydrodynamic study indicates that high air dispersion degree and strong lower slurry circulation could be produced by pilot scale special flotation cell, which is helpful to create a suitable hydrodynamic environment for quartz sand processing.INTRODUCTIONNatural quartz is a non-metallic mineral, which is widely used as raw material in multiple industry process (Shifu, 2006). High purity quartz, especially containing more than 99.9% silicon dioxide, is characterized by high temperature resistance, small thermal expansion coefficient, highly insulating and so on. The demand of high purity quartz has been rising along with social and economic development, now high purity quartz is widely used in the field of photovoltaic industry, electronic information, communications and aerospace industry.Quartz is a kind of main rocking-forming minerals in the nature. There are seven genetic types, such as natural crystal, quartz sandstone, quartzite, vein quartz, konilite, natural siliceous sand, granite quartz (Baolei, Shuilin, & Dianchao, 2012). The natural crystal is primarily used as raw material to refine high purity quartz, but it is not available for two reasons. On the one hand, the natural crystal is extremely expensive and poor in resources reserves, which can not satisfy the need of large-scale industrial production. On the other hand, the chemical component of natural crystal is instability, it may lead to low stable product performance in large industrial applications, and it is also difficult to achieve raw materials standardization. Therefore, there are a lot of studies to search for other technological methods to obtain high purity quartz from other genetic quartz types."

Jan 1, 2016

By Marc Tardif

"The way alarm information is provided to an operator can make a huge difference in the minutes following an upset. Process alarms are often looked at as a way to help avoid catastrophic failure and serious accidents. But knowing that mineral processing is so energy consuming and that raw material is not consistent, all small upsets should also be seen as a catastrophe because they can have significant impact on product cost and quality.This paper will demonstrate how it is possible to use data from process alarms to provide operators with real time, value added information that will help them take the right decision at the right time and in turn, reduce unplanned downtime by 20 to 80% and incidents by up to 50% (number and cost),and optimize energy and capacity usage.In the era of Big Data, living in a world where we are submerged with information, one of the biggest challenges is to find the right information at the right time.Alarm rationalization projects will often focus on alarm quantity, but alarm quality is also very important. It is possible, by following a simple 6-step process to turn “alarms” into truly valuable information for operators. Based on known standards (ANSI/ISA 18.2 and EEMUA 191), this process will capture the knowledge of the best and most experienced operators and process engineers, and make it readily available to everyone, right on time, when it matters the most.INTRODUCTIONWhen spending some time in a modern control room, it is easy to notice the huge quantity of information that is available to the operator. Modern operation stations feature multiple screens with HD capability. These screens display information like process display, history trends, alarms and events list, maps with geo-located information, images from live cameras, etc. However, it is harder to assess whether all this information is really helping operators: Is all the information relevant? Are process screens overcrowded? Is the information easy to understand? Does the operator know what to do with all the information? Are there too many alarms?"

Jan 1, 2016

By H. Staton, V. Suontaka, E. Sharifi

"Flotation circuits are typically controlled using on-line elemental assays obtained from the slurry lines. In base metal applications, X-ray fluorescence (XRF) analyzers are the most common instruments for elemental analysis of the slurries. Eagle Mine has been utilizing a Courier XRF Analyzer since 2014. Typically, in XRF analysis, the sampling rate is 10-25 minutes which is good enough for manual process control. In 2018, Eagle Mine upgraded the Courier XRF analyzer with the Rapid Measurement module that is based on reflectance spectroscopy. This option reduces the sampling rate to 10-15 seconds, while maintaining the superior accuracy of the XRF analyzer. This paper presents the results from implementation of Rapid Measurement at Eagle Mine.INTRODUCTION Eagle mine is an underground mine producing nickel and copper concentrates. Eagle Mine is owned by Lundin mining and located in the Upper Peninsula of Michigan, USA. The Humboldt Mill, previously an iron ore processing facility, was refurbished in 2014 and is used to process the ore and produce separate nickel and copper concentrates. Approximately 2,000 metric tonnes of ore is milled per day. Ore is processed using a conventional crushing followed by single stage ball mill and flotation. Nickel and copper concentrate are transported to facilities in North America via rail car. A bulk copper-nickel concentrate is produced by separating the copper and nickel minerals from gangue material by flotation. The copper-nickel bulk concentrate is reground, followed by one stage of cleaning to reject further gangue minerals. The bulk cleaner concentrate is then subjected to a final flotation stage where the copper and nickel minerals are separated from one another through the addition of lime. Final concentrate grades are 14% Ni and 2% Cu in the nickel concentrate and 31% Cu and 0.8% Ni in copper concentrate."

Jan 1, 2019

By H. M. Giegerich

"INTRODUCTIONThe Red Dog Project in Alaska is being developed by Cominco Alaska, a subsidiary of Corninco Ltd. of Canada, and the Nana Regional Corporation, one of the 12 native corporations created by the Alaska Native Claims Settlement Act of1971.The State of Alaska is also a very key part of the project through its financing of the transportation system for Red Dog. Red Dog will be the third, and largest, of Cominco's Arctic mining developments in the past thirteen years, after the Black Angel Mine in Greenland, which started up in 1973, and the Polaris Mine in the Canadian Arctic, which began production six years ago in 1982.Red Dog is one of the world's great mineral deposits, with a unique combination of large size, high-grade, and a waste-to- ore ratio less than I: I, which will make it the world's largest, and one of the lowest cost zinc producers, when at full production. The present mineral reserve is estimated to be 85 million tons , at a grade of 17.1010 zinc, 5% lead, and 2.4 ounces per ton of silver. Based on the current production forecast, this will give a mine life of almost 50 years, and the deposit is still open in two directions, although the structure is becoming thinner at depth. As well, there is a satellite zone about one mile south of the main deposit which could contain up to another 8 million tons of mineral at Red Dog grades or better. This is not presently included in the reserve due to potential processing difficulties.In relation to other zinc deposits, Red Dog is the second largest ever discovered, smaller than the original Broken Hill deposit in Australia, but larger than Cominco's own Sullivan Mine in British Columbia, which is number three. It is quite possible that, when the area is adequately explored, Red Dog will be number one."

Jan 1, 1989

By Peter N. Calder

Long range mine planning involves developing a mining sequence that schedules the extraction of the ore and waste materials within a final pit limit. The objective is to define a sequence that best meets the defined strategic objectives. The main steps in the creation of an open pit mine plan are the final pit limit design, the design and sequencing of the mining phases, equipment selection and operating cost estimation. Flexibility is the key strategic element in developing a mine plan. Planning the extraction sequences and rates for the various mining areas is a challenging and demanding activity. It is often necessary to consider numerous alternative strategies and what if scenarios. The number of alternatives that can be studied with limited manpower and time resources is restricted. In order to investigate strategic aspects of mine planning, a system to generate workable mine plans rapidly is required. The concept of Visual Mine Planning is that the engineer can visualize the current plan, easily change a component of the plan, such as the annual cut-off grade schedule or the production rate within a particular Phase, and immediately see the effect on the mineralogical and cash flows. If the desired result is not achieved, a change is made and the effect is again immediately seen. This paper presents results of research in this area conducted at the Pontificia Universidad Católica de Chile. The work includes the examination of cut-off grade strategy, sequencing, blending, stockpiling and shovel-truck fleet requirements using simulation.

May 1, 2003

By Robert Voisey, Robert J. Spencer

"LynnGold's MacLellan Mine is located about 8 km south east of Lynn Lake immediately to the east of the Keewatin River (Fig. I). The property is accessible by an all-weather road, leading north from the provincial highway 391, which links with the Town of Leaf Rapids and the City of Thompson to the south.The ore body, as outlined in the original feasibility study, is expected to produce in excess of 9.3 x IQ6 gm of gold and silver over the next 5 years. However, the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan Mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 48 km west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan Mine or relocated to Sherrin's Ruttan Operation.GeologyThe MacLellan gold ore deposit is located on the northern section of the Lynn Lake Greenstone Belt known as the Rainbow Trend. This Trend is a 40 km gold bearing rock sequence extending both east and west from the MacLellan Mine. The southern section of these two east-west trending structures is known as the Johnson Shear, this is also gold bearing."

Jan 1, 1990

By Andrea Lisjak

The mechanical behaviour of Opalinus Clay, an indurated over-consolidated argillaceous rock, is heavily influenced by the presence of preferably oriented bedding planes. The objective of this study is to illustrate a new modeling approach aimed at capturing the bedding-induced anisotropy of Opalinus Clay as observed in the laboratory and in situ. The combined finite-discrete element method (FEM/DEM) is employed as the main simulation tool. FEM/DEM is a numerical method that models material damage processes by explicitly considering fracture nucleation and propagation. A transversely isotropic elastic constitutive law is used to account for different elastic property values in the direction parallel and perpendicular to the layering, while strength anisotropy is captured using a directional cohesive fracture model. Quantitative calibration and validation of the model is based on laboratory results of indirect tensile tests and uniaxial compression tests. Emergent strength and deformation properties, together with the simulated damage mechanisms, are shown to be in good agreement with experimental observations. Preliminary results relative to the analysis of a circular tunnel show that the approach is able to reproduce the main Excavation Damaged Zone (EDZ) formation mechanisms as observed in the field.

Jun 1, 2012

By G. Langlands

"R. Tenbergen Is this flotation machine suitable in the flotation ofInco ball mill discharges where we have a coarse feed at 60% solids?Reply Experience has shown that there is not a significant increase in the wear life of these machines when handling coarse material (8 mesh) at 60% solids. A common practice in Europe is shut down on the week-ends.The material is allowed to settle and on start-up an injectic of air for 15 seconds is sufficient prior to start-up. At,mining we put our unit in the middle of a bank of 44 cells and in order to ensure severe sanding we shut the aker cell down while the remaining cells kept running. After 20-25 seconds of air the cell started without trouble.P. Mahant Is there a build-up inside the impellor shaft housing? Falconbrige Ltd.Reply There is no sand build-up but rather a scale build-up which due to a flexing action frees itself periodically. Part of the design of the machine permits a water injection into the shaft housing to free any build-up. This is done in Europe during the week-end shut down."

Jan 1, 1984

By M. P. Rennick, D. M. Burton

Abstract -The Murray Brook massive sulfide deposit, which was the first geochemical discovery in the Bathurst camp, is one of the largest sulfide deposits in the area. The massive sulfides are hosted by quartzose metasedimentary rocks in the lower part of the Ordovician Tetagouche Group. This thick succession of sedimentary rocks is overlain conformably by felsic volcanic rocks, and is structurally overlain by mafic volcanic rocks. The massive-sulfide body is polydeformed, but primary metal zoning is still discernable and may permit future exploitation of discrete lead-zinc and copper zones. Although it was discovered in 1956, the deposit was not developed unti11989, when Murray Brook Resources commenced processing of gossan containing precious metals. Recovery of gold, silver, and mercury is accomplished by indoor vat leaching on a year-round basis.

Jan 1, 1992

By Y. Obara, A. Sato

"Limestone is one of the most important mineral resources, and in Japan it is only one mineral which can be fully supplied by the domestic product. Generally limestone mines in Japan located at mountainous regions, and the combination between bench-cut method and the carry-out system using vertical shaft is widely used in the domestic mines. During mining operations, the occurrence of the blockage in the vertical shafts is very serious problem. Once the blockage in the shafts is occurred, a lot of works and dangerous procedures are necessary to solve the problems. It is thought that blockage is influenced by the cohesion and friction coefficient due to clay minerals thrown into the vertical shafts, however, the quantitative and precise reason is not revealed yet.In this study, the process of blockage occurrence was simulated by 2-Dimensional Discrete Element Method (DEM). In the 2D-DEM analysis, discontinuous circular particles are generated, and the individual movement of each particle is calculated by forward difference method. In the analysis, several typical ore distributions are applied, and the DEM analysis was conducted under the various combinations of cohesion and friction coefficient. From analytical results, it was found that the friction coefficient strongly influences to the occurrence of blockage and there were a threshold values which blockage does not occur. Several kinds of shaft shape were also simulated towards different ore size distributions, and those influences to the blockage occurrence were also discussed."

Jan 1, 2015

By D. Brossman

"The virtue of spray drying is that it is a drying method, and so far the only one by which it is possible in one operation to divide a mineral concentrate into its basic primary particles.,In so doing, each particle gets the same treatment and the result is a dry concentrate more homogeneous than any other known concentrate drying process. This is particularly good for a flash furnace requiring a bone dry finely divided feed. The spray dryer also features a very short residence time and due to the very quick operation the solids are kept cool thus preventing any risk of fire or explosions on these pyrophoric materials.There are many spray dryers now in operation in the mining industry and one of the latest applications is in South Africa where a spray dryer is treating a copper-nickel platinum concentrate which is, after drying, fed toan electric arc furnace. Experience has shown that the concentrate should contain 4% moisture for the furnace, and this is achieved by drying the concentrate bone dry and then back-mixing with thickener underflow pulp to provide an extremely homogeneous feed to the smelter. As mentioned before, mixing with pulp would be more of an advantage because we would not be evaporating water which would have to be added again afterwards.One of the first spray dryers to go in was at Western Mining Corporation in Kambalda in Western Australia. (A series of slides was then shown)."

Jan 1, 1972

By M. P. Rennick, D. M. Burton

The Murray Brook massive sulfide deposit, which was the first geochemical discovery in the Bathurst camp, is one of the largest sulfide deposits in the area. The massive sulfides are hosted by quartzose metasedimentary rocks in the lower part of the Ordovician Tetagouche Group. This thick succession of sedimentary rocks is overlain conformably by felsic volcanic rocks, and is structurally overlain by mafic volcanic rocks. The massive-sulfide body is polydeformed, but primary metal zoning is still discernable and may permit future exploitation of discrete lead-zinc and copper zones. Although it was discovered in 1956, the deposit was not developed until 1989, when Murray Brook Resources commenced processing of gossan containing precious metals. Recovery of gold, silver, and mercury is accomplished by indoor vat leaching on a year-round basis.

Jan 1, 1992

By Eugene Larochelle

The serpentine of the Eastern Townships of Quebec is more or less seamed and impregnated with chrysotile asbestos, of which we note two types: the cross-fibre and the disseminated fibre. The cross-fibre type always appears in fibres or crystals arranged parallel to one another, and disposed at right angles to the walls of the matrix serpentine. The length of fibre of these veins, which run in every conceivable direction, even crossing ?one another, varies from microscopie dimensions to three and sometimes four and even five inches. It is the principal form of asbestos found in the serpentine of Thetford Mines, Black Lake, Coleraine, and Asbestos. The disseminated-fibre type, which is the main product of the serpentine of Broughton township, in which ate located the mines at East Broughton, does not form veins, but occurs in the serpentine without any definite arrangement. There is a difference in the toughness and hardness of the rock of the two types, the Broughton serpentine being softer than that at Thetford. The disseminated-fibre section of the serpentine belt is probably more regular in its content than is the cross-fibre section. Nevertheless, it contains no 'crude,' which is the most valuable of asbestos, and the fibre is usually shorter than the cross-fibre average.

Jan 1, 1928

By C. F. Hews, P. N. Calder

"MIROC and The Mining Industry The Mining Industry Research Organization of Canada (MIROC), incorporated in 1975, is a non-profit organization sponsored by member companies from within the Canadian mining industry. The Canadian mining industry is a world leader in technological development and in organizational and human resources development. A prime objective within the industry is to retain this leadership and also improve its competitive position worldwide.MIROC is dedicated to support the objectives of its member companies and their common interest, and the objectives of the industry. In this context: MIROC's mission is to encourage the formulation of ideas to improve mining technology and methods by any source, and to foster the development and testing of promising initiatives in progressive steps from the early stages of conceptual and feasibility research through manufacture to delivery of new technology to the mining industry. In so doing MIROC plays an important role in the development of individuals skilled in mining research. Management ApproachMIROC's research program is driven by member companies who have interests throughout Canada. The board of directors approve projects that are acceptable to its members. While MIROC's basic research funding is provided by its member companies, about 30% of its annual research budget is now derived from royalties generated from previous research activities."

Jan 1, 1994

By Mori Fresko, Stuart M. Jones Jr

"This paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide, through the end of 2010. Updates have been solicited from all major mill manufacturers and most have responded.A review of AG/SAG mills sold to date and in the last five years indicates that the AG/SAG mill market is very healthy and the trend is larger diameter mills with high diameter-to-length ratios. Ring motors (gearless) are the preferred drives for large mills even though the power transmitted through a gear drive is expected to near 11,000 kW per pinion in the near future.INTRODUCTIONThis paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide. The list is maintained by Stuart M. Jones, Jr. (author), and is included in the appendix. This list has been the inspiration for similar papers in the past several SAG Conferences. Updates have been solicited from all major mill manufacturers and most have responded. Information from this list is compiled to illustrate the growth of the AG/SAG mill market and the use by industry and selected geographic areas. It covers the market growth through the end of 2010."

Jan 1, 2012

By I. Clauzier

"A new method of managing electricity to reduce costs andimprove profits is discussed. Before taking steps to better manage electricity, it is essential to understand the terms peak demand and energy and their effect on an electrical bill. Knowing how electricity is presently used in the plant is the important first step. This goes beyond knowing how much electricity is used at each time of day, the individual contribution of every plant process to the total plant load must be known. At this point, each process is ranked according to importance to production in order to identify possible savings opportunities. These improvements can then be implemented by simply improving operations or in some cases, through the use of an automatic control system. IntroductionIn today's competitive environment, controlling costs is becoming increasingly important. All costs associated with operation must be controlled in an effort to improve competitive position. Electricity is a cost component that can and should be managed.Although the term management can mean different things to different people, the intent is always the same: to make the best possible use of existing resources, whether labour, equipment or electricity.The simple approach to managing electricity presented in this paper consists of four steps.I. Understand Peak Demand and Energy. It is essential to understand the terms, peak demand and energy and their effect on your electrical bill.2. Know Your Present Electrical Use. The present use of electricity in the plant must be known. This goes beyond simply knowing how much is used at each time of day, to accurately knowing how each process is contributing to the total plant electrical load, and ultimately to the electrical bill.3. Identification of Savings Opportunities. With this information, energy savings opportunities for reducing the electrical bill and improving profits can be identified.4. Implementing Improvements. Having identified areas of potential savings, improvements can then be implemented in order of their significance. This could be a matter of simply improving operations, or in some eases may mean the use of an automatic control system.These four steps can result in significant dollar savings."

Jan 1, 1987