Search Documents

By Edward L. McHugh

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 5-acre Zwagg Island Wilderness Study Area (OR-12-14) in order to evaluate its identified mineral resources. The study area is located in Curry County, OR, immediately west of Brookings. There is no evidence of mining activity on or near Zwagg Island, and no mineral resources were identified. The steep-sided, flat-topped island is normally accessible from the mainland by way of a sandy beach. The island consists mainly of marine sandstone, mudstone, and conglomerate of the Jurassic Dothan Formation. Dothan Formation sandstone has been used locally as construction material. Rock along the coast has also been used for construction of jetties to improve harbor access; additional work has been proposed at the port of Brookings. Although suitable for other construction uses, stone from Zwagg Island would probably not meet physical requirements for jetty stone. Development of a stone resource on the island is unlikely.

Jan 1, 1987

By H. A. Doerner

"The pure mineral chromite, FeO.Cr203, consists of ferrous and chromic oxides, chemically united in equal molecular proportions. Unfortunately, pure chromite as defined above appears to be a rare exception. In most chrome ores the mineral may be considered a combination of spinel, MgO.Al203, and chromite, with the latter predominating. The ratios between the four common constituents Fe0, Mg0, Cr203 and A203 vary greatly, and other minor constituents such as TiO2 and. Fe203 may also be present.In the mechanical concentration of chromite ores the maximum grade of concentrates that can be produced is thus limited by the composition of the chrome minerals present. Pure chromite contains 68 per cent Cr203, but the Cr203 content of the chrome minerals in commercial ores varies between 45 and 60 per cent and the average is not far from 55 per cent.Chromite is usually associated with serpentine. Other silicates, quartz, dolomite, magnetite, ilmenite and other iron Minerals are frequently present.The amenability of a chrome ore to concentration, depends upon the kind and amount of the various gangue minerals present and the amount .of crushing necessary to separate the chromite from them.A relatively small amount of chrome ore is concentrated by milling. In most cases the mine product is simply hand-sorted. Such chrome deposits as are known in the United. States can not be worked in this way on account of one or both of the following conditions: High cost of labor and finely disseminated impurities. There are, however, several deposits in the United States, Canada, and Alaska which may be able to compete with imported or by efficiently utilizing modern ore-dressing and milling methods."

Nov 1, 1930

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

Unlike other types of mining accidents, where an incident generally involves only a few workers, the danger of a mine fire extends to every person working in the underground environment. Mine fires can trap or kill those working underground by blocking avenues of escape and rapidly creating heat, asphyxiating gases and toxic fire products that can quickly spread throughout the mine. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate and improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Because wood is the second most abundant fuel available during a coal mine fire, it was decided that a series of large-scale wood crib fire tests was needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.1

By J. A. Kost

The objective of Contract J0295041 was to determine if the addition of a surfactant (wetting agent) to the water used for dust control in underground coal mines results in the reduction of airborne dust. Laboratory wettability tests, including the capillary rise test, a coal dust sinking test and zeta potential measurements, were used to select a coal seam/surfactant combination for in-mine testing. Four surfactants were selected for underground testing: Surfynol 465, Aerosol MA-80, DC-13, and Dustallay. The underground tests in the Lower Kittanning seam, Indiana County, PA, involved a Wilcox Mark 20 auger mining system, equipped with spray nozzles located on the cutting augers, Conflow venturi sprays, and a spray manifold. Respirable dust samples were provided by MSA Model G personal samplers and Simslin II instantaneous dust monitor; total airborne dust samples were provided by MSA Model G samplers with UNICO filter cassettes. Based on data obtained from 24 test periods surfactants, as compared to plain water, reduced the airborne respirable dust an average of 27 percent and total airborne dust an average of 36 percent.

Jan 1, 1980

By John Kosek

The electrochemistry of carbon monoxide, nitric oxide and nitrogen dioxide was investigated at a variety of electrode materials in different supporting electrolytes. A portable detector for carbon monoxide was developed using a porous gold anode in perchloric acid supporting electrolyte. This detector has two full scale ranges, 0-100 ppm and 0-500 ppm. A portable detector for mixtures of nitric oxide and nitrogen dioxide was developed using a porous silver cathode in sulfuric acid supporting electrolyte. Nitrogen dioxide was determined in the gas stream by electroreduction. The nitric oxide in the gas stream was oxidized to nitrogen dioxide by passing it over Cr(VI) on firebrick. Electroreduction gave the sum of NO + N02. Analog circuitry was used to display the amounts of NO and N02 separately. Two ranges were available for each gas. They were 0-10 and 0-50 ppm for NO and 0-2 and 0-10 ppm for N02.

Jan 1, 1979

By F. Albayrak

This report is a study of the impact of Federal laws and regulations on the domestic supply of metallic and nonmetallic minerals. The study was confined to pertinent environmental legislation and the recently enacted Federal Mine Safety and Health Act of 1977. Emphasized were the legal requirements placed on individual selected mineral industries, and the economic impact of these requirements. A certain amount of attention was also directed to the particular environmental and health and safety problems generated by selected mineral industries. The study also pinpointed a list of major problem areas having significant impact on the domestic mineral supply.

Jan 1, 1978

The above referenced contract between Badger Manufacturing Corporation and the U. S Bureau of Mines was executed June 30, 1975, as a result of the request for proposals for innovative machine concepts. We selected the cutting machine category because of the obvious lack of technical progress in this field for many years: Phase I of the contract required blasting fragmentation tests to determine proper blasting patterns for use with the auger-type kerf cutting machine. Phase II required design concept development for a machine capable of cutting a circular void as an aid to blasting.

Jan 1, 1975

By Daniel Ng

The U.S. Bureau of Mines-Michigan Technological University mine ventilation mainframe program was successfully adapted for execution in a personal computer (PC). The hardware requirement can be as modest as 256 kilobytes (33) of random access memory (RM) and two floppy disk drives. A version compiled for a PC possessing 512 Kb RAM has arrays dimensioned to accommodate 512 separate mine airways and junctions, and it contains all the features and capabilities of the original version. It has successfully analyzed all the ventilation networks tested, including a very large commercial mine (404 airways, 237 junctions, and 5 fans). In all cases the PC version produced practically identical results as obtained from the mainframe computer. In all respects, the PC version performed the same as the mainframe version with the exception of execution speed When a numerical coprocessor is employed, execution time can be reduced by more than 50%.

Jan 1, 1989

By D. A. Stanley

The Bureau of Mines conducted laboratory-scale experiments to determine whether or not surface waters with a high organic content could be purified sufficiently to be used to replace the natural high-quality deep well water currently being used in the silica flotation step of phosphate rock beneficiation. Waters abundant in organic matter were collected from two central Florida streams, flocculated with a cationic polyethylenimine polymer, and processed in a sand filter. This treatment removed most of the organic materials from the water. Untreated surface water, treated surface water, and distilled water were used to compare the flotation response of the acid insolubles in an amine flotation circuit. Surface water treated with PEI-1000 was shown to be as effective as distilled water for the acid-insoluble-flotation step. Flocculation and filtration can therefore produce water suitable for amine flotation of quartz, which would permit substitution of surface water for deep well water.

Jan 1, 1981

By W. G. Phillips

This report presents results from a study whose objective was to evaluate noise control options for existing equipment used in metal and non-metal processing plants. This equipment performs 3 basic functions, crushing, grinding to a point where the product can be liberated from the waste, and agglomeration A the product. Specifically, the study was directed towards taconite processing since the extreme hardness of taconite results in high noise levels and in considerable maintenance of the processing equipment. Both of these factors make this process a very challenging noise control task. Plants processing other ores use similar equipment, consequently the results of these studies should he applicable to a wide variety of plants. The report presents the source diagnosis and potential retrofit noise control treatments for fine screens, mills, crusher sizing screens, and vacuum disc filters. Estimates are make of the noise reduction from each treatment. The report concludes with recommendations for future research on each piece of equipment.

Jan 1, 1978

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By Bryan R. Carmenati

This report documents the need for formal health and safety, and equipment operations training in the mine construction industry. The outlines, objectives, and training texts were developed based on the recommendation of needs of mine construction personnel, and those of Dames and Moore (Safety Analysis of Shaft Sinking operations, 1977) and Kinton, Inc. (A Training Program for Conventional and Raise Drill Construction Personnel; Phase I, 1979). The training material samples contained herein (and under separate cover in its entirety) are designed to improve the safety and production of those in mine construction. An instructor-directed presentation is recommended. The results of the study are presented in the Findings and Recommendations section of this report.

Jan 1, 1982

By Terry J. Close

A mineral resource survey of the 236-mil (611-km2) Hyalite-Porcupine-Buffalo Horn wilderness study area (RARE 11 Areas No. 1-155 G, Gallatin Divide; and H, Hyalite) between the Gallatin and Yellowstone rivers in Montana, indicates there are phosphate rock and petrified wood resources (fig. 1). The area also has some potential for oil, gas, and geothermal resources. Stone and alluvium are abundant but appear to have little potential for development because other sources are available nearer to markets.

Jan 1, 1981

By Robert J. Dompe

The objective of this program was to develop a cost effective microprocessor-based electronic image sensor system for monitoring pit slope displacement to detect and/ or predict impending slope failure in surface mines. A background study and data analysis yielded a performance specification for candidate Video Slope Monitoring Systems. A design concept was developed based on using a pair of solid state video cameras located on precision pointing assemblies. The digital images from the cameras are compared and, using electronic triangulation, slope topology is calculated. The current and past locations of operator selected features are compared to determine pit slope displacement. A proof-of-concept test was performed using a laboratory model of a pit slope. Based on the successful results of that testing it is recommended that an in-mine evaluation be performed using a full-scale prototype Video Slope Monitoring System.

Jan 1, 1982

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983

By J. R. Thoenen, J. L. Vallely, M. C. Malamphy

"SUMMARYMagnetic and gravimetric surveys wore conducted over an area of ap¬proximately 1,400 square miles in the bauxite district of central Arkansas. The primary purpose of these surveys was to discover any possible buried and hitherto unknown syenite masses favorable for the occurrence of bauxite and to determine the approximate position of the buried flanks of the known syenite masses which might offer conditions favorable for the discovery of new ore bodies.Those surveys indicated that the various syenite outcrops were domes or bosses on a large batholith and that ether similar domes occurred on the batholith but did net outcrop.Drilling on the local geophysical anomalies proved the presence of 10 buried domes, but only 2 of them were found to project above the upper surface of the Midway clays, a requisite of conditions favorable for the occurrence of bauxite ore bodies. The geophysical data indicated the approximate configuration of the buried flanks of the known syenite coutcrops, and the portions of these flanks that project above the Midway have now been outlined more accurately by drilling.The geophysical surveys have produced evidence permitting the elimi¬nation of a large area as unfavorable for the occurrence of bauxite.Magnetic surveys extending along the Midway-Wilcox contact from Gurdon, in Clark County, on the southwest to Searcy, in White County, on the northwest have proved the improbability of the existence of other syenite masses similar to those found in Pulaski and Saline Counties. A detailed magnetic survey of the Magnet Cove area in Hot Spring County has proved that the syenite mass exposed in that locality is an isolated intrusion and entirely unrelated to those of Pulaski and Saline Counties. This syenite mass does not occur under conditions believed to be favorable for the occurrence of bauxite."

Feb 1, 1945

By Earl T. Hayes

[This work represents a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of mineral physics to process metallurgy.]

Jan 1, 1941

By Earl T. Hayes

[This work represent a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of miner physics to processes metallurgy.]

Jan 1, 1941

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

Table A-1. Number of underground coal mines and samples collected for underground occupations, 1988-92 [ ]

Jan 1, 1997