Search Documents

By J. L. Buckley

A survey of previous underground mine fires revealed a number of reported fires may have been caused by malfunctioning stationary electrical equipment. Therefore, an evaluation of conventional fire protection systems was conducted to determine their usefulness in the protection of this equipment. To simplify the problem and facilitate the handling of data, the under-ground mine was divided into nine work areas. Representative combustibles and associated hazards characteristic of each area were identified. Conventionally available fire protection systems were then examined and evaluated to determine engineering and cost feasibility, effectiveness and reliability for the development of fire protection guidelines which could be used within the nine areas of interest.

Jan 1, 1976

By Jack L. Henry, Davis E. Traut, L. R. Penner

The Bureau of Mines conducted solvent extraction batch tests to evaluate the usefulness of neodecanoic acid ( NDA) for extracting Co 3+ from ammoniacal leach liquors high in ammonium sulfate . This work is an outgrowth of previous Bureau research in which technology was devised for the recovery of cobalt , nickel , and byproduct copper from domestic laterites . The previously devised technology uses an oxidative ammoniacal sulfate leach to treat the laterite , and nickel and copper are then recovered from the leach solution by solvent extraction and electrowinning . This report deals with the subsequent solvent extraction of cobalt from the nickel - copper raffinate solution . The results showed that about 70 pct of the contained Co 3+ can be extracted batchwise at pH 8 using NDA ( a 10 - carbon - chain highly branched carboxylic acid ) . However , NDA had a solubility of approximately 0.6 to 0.8 g / L in aqueous raffinate following extraction , and this high solubility makes it impractical for use with alkaline solutions that are low in cobalt . In addition , the extracted cobalt species ( predominately cobaltic hexammine ) is not amenable to the electrolytic recovery of cobalt metal because of its extreme stability . This fundamental prob-

Jan 1, 1965

By W. W. Adams

Three hundred and twenty-eight mines and quarries, representing 36 States, took part in the twelfth yearly accident-prevention contest conducted by the United States Bureau of Mines and known as the National Safety Competition. Four underground mines and one open-cut mine (which represents the quarry and open-cut mine group), each the leader in its group, were awarded the ?Sentinels of Safety? trophy. Relative standing in the contest" was determined by the number of days lost from accidents in proportion to the total number of man-hours worked. Since 1925, when the National Safety Competition was inaugurated, an increasing interest has been taken in it by mining and quarrying companies as a means of stimulating mine and quarry safety by competition among similar plants. Each participating plant can, on a basis of its standing and record in the contest, determine to what extent its safety program is succeeding or to what extent it needs strengthening. With this information, each company that has a low standing in the contest can intensify its safety-promotion efforts the following year to obtain a lower rate and possibly win the trophy or achieve honorable mention in the competition. Except for 1929, the National Safety Competition of 1936 represented more man-hours of employment than any other year since the yearly contests began.

Jan 1, 1937

By David E. Siskind

A Bureau of Mines survey of noise from quarry production blasting was conducted at seven crushed-stone quarries, providing information on close-in noise generation, comparative instrumentation, and evaluation of the sound levels as related to blasting parameters and existing State and local noise standards. The results from this preliminary survey will be useful in the design of a complete investigation of the problem of noise from blasting. There exists an immediate need for technical guidelines for noise pollution control agencies presently working on the regulation of impulsive noise sources. This survey and results from previous work by other researchers are used to derive interim recommendations on weighting scales, generated sound levels, and instrumentation. These recommendations are based on the limited data presently available and may be modified with subsequent investigation of noise generation, propagation, structural damage, and human tolerance.

Jan 1, 1974

By B. W. Madsen

The Bureau of Mines conducted a large-scale (6.4 t), long-term (2,165 days) test to gain a better understanding of the leaching characteristics of chalcopyritic ores. An ore sample containing 0.77 pct Cu was leached in a fiberglass column by downward percolation of acidified ferric sulfate solutions. Three sets of leaching conditions were investigated: (1) ambient temperature leaching, (2) elevated temperature (50° to 60° C) leaching, and (3) elevated temperature leaching after inoculation with thermophilic bacteria. Leaching at ambient temperature resulted in a copper extraction rate of 0.44 pct per 100 days. Increasing the temperature to 50° to 60° C resulted in decreased activity of natural mesophilic bacteria, and the leaching rate decreased to 0.22 pct per 100 days. The pH was lowered from 2.0 to 1.6, and nutrient solutions that contained thermophilic bacteria were added. This procedure resulted in an increase in the ferric-to-ferrous iron ratio and an increase in the copper leaching rate. However, the increased leaching rate was not sustained, and 120 days after inoculation the bacterial activity declined, the ferrous iron content increased, and the copper leaching rate decreased.

Jan 1, 1983

By M. L. Wang, S. R. Short, E. M. Daniloff, E. L. Petsonk, D. M. Mannino, G .. R. Wagner

"Background—It has been suggested that health related job selection is a major cause of the healthy worker effect, and may result in inaccurate estimates of health risks of exposures in the working environment. Improved understanding of self selection, including the role of airway hyperresponsiveness, should improve accuracy in estimating occupational risks.Methods—We evaluated symptoms of the respiratory tract, lung function, occupa¬tional and smoking histories, and airway responsiveness from a cross sectional sur¬vey of 478 underground bituminous coal miners and non-mining controls. Workers with abnormal spirometry were excluded from methacholine testing.Results—Methacholine responsiveness (= 15% decline in forced expiratory volume in one second) was associated in both miners and controls with reduced ventilatory lung function and an increased risk of respiratory symptoms. Miners with the longest duration of work at the coal face had a low prevalence of methacholine responsiveness, compared with miners who had never worked at the coal face (12% v 39%, P < 0.01). Throughout their mining careers, miners who responded to methacholine were consistently less likely to have worked in dusty jobs than miners who did not respond to methacholine.Conclusions—These results provide evidence that workers who are employed in dusty jobs are less likely than their unexposed coworkers to show increased non-specific airway responsiveness, pre-sumably as a result of health related job selection. Surveys of workers in which responsiveness data are unavailable may underestimate the effects of dust exposure on respiratory health."

Dec 1, 1996

The Bureau of Mines performed cratering experiments in a homogeneous granite to test scaling laws for charge weights of 0.00476, 0.0220, 0.0900, 0.304, and 1.03 lb. Agreement among the data was best when empirical scaling exponents greater than one-third were assumed. Although the analysis showed that the best empirical scaling exponents were 0.37 for crater volume, 0.38 for crater radius, and 0.39 scaling for crater depth, all three crater dimensions could be scaled with a 0.38 scaling exponent.

Jan 1, 1970

By C. A. Mehring

[This paper, which describes the milling practice at the San Guillermo concentrator of the Compania Industrial "M Potosi", S.A., located at Chihuahua, Chihuahua, Mexico, is one of a series of similar papers being prepared by the United States Bureau of Mines. The concentrator treats lead-zinc-silver ore at the rata of 2,300-2,400 tons of dry material daily and produces lead concentrate and zinc concentrate by selective flotation methods. The lead concentrate is smelted at the Chihuahua plant of the American Smelting & Refining Co., and the zinc concentrate is shipped to various European smelters.]

Jan 1, 1933

By Thomas J. Peters

The King Mountain study area is centered about 120 air km northwest of Blackfoot, and 30 air km north of Arco, Idaho. The study area makes up the southern one-third of the northwest-trending Lost River Range--the highest mountain range in Idaho. The area is predominantly underlain by Paleozoic-age marine limestone and lesser dolostone, with a relatively small inlier of silica-rich, Ordovician-age quartzite. There are vast, unquantified resources of these industrial minerals present; however, special markets need to be developed for these resources which are near enough for transportation costs to be competitive. Five prospects were found in the study area; however, only one, the Elbow quartz silica prospect, contains resources and current claims. There has been no mineral production in the study area.

Jan 1, 1993

By P. Yant, R. R. Sayers, R. D. Lieitch

"PURPOSE OF INVESTIGATIONOf more than 300 bituminous mines examined by Crichton 5 and his assistants in connection with litigation in Indian Creek Valley, Payette County, Pa., only four were found to have alkaline water. That work and many observations from of the authors have shown the general prevalence or acid drainage from bituminous coal mines. In connection with investigations pertinent to coal-mine drainage that are being conducted by the United States Bureau of Mines, it was noted with considerable interest therefore, that a mine in the Thick Freeport bed about 20 miles north of Pittsburgh had no acid water in the workings, As it was thought that this condition might be common to all mines,this condition in this bed most of them were visited, samples of the outflow and from different parts of the mine inside were examined, and such general information as was available was gathered.ACKNOWLEDGMENTSThe authors acknowledge with thanks the courteous assistance of mine officials in connection with collecting the data for this paper, and of the analytical and coal laboratories of the Bureau of Mines for analyses."

Nov 1, 1932

By J. A. Eisele

The Bureau of Mines is investigating the recovery of alumina from domestic nonbauxitic resources, including anorthosite. The United States has large reserves of anorthosite, but its aluminum content is less than 50 pct soluble in acid, unless a source of fluoride is added to the acid. A flowsheet that includes leaching with HCl and fluoride followed by crystallization of AlC13.6H20 from the pregnant liquor by HCl gas injection was designed. Approximately 90 pct of the aluminum values were recovered from the anorthosite when a ratio of 0.14 mole of fluorine per mole of aluminum was used. Sodium chloride is cocrystallized with the A1C13.6H20 but is removed by water washing of the Al203 product. A material balance is given based on results of laboratory studies of the unit operations.

Jan 1, 1983

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By George L. Gates

This report presents is an evaluation by the Federal Bureau of Mines of the effect of clay-water, brine, and oil-base drilling fluids on the productivity of test wells drilled on the Umiat anticline in U.S. Naval Petroleum Reserve No. 4 in northern Alaska. Eleven, wells were drilled on the Umiat structure as part of the U.S. Navy&apos;s extensive exploration of the Reserve during 1944-53 to determine the possibilities for oil production. The Federal Geological Survey cooperated in the exploration program and has published a comprehensive report3/ on the geology of the area and case histories of the wells. The re¬port also includes the results of special studies by the Bureau in connection with the drilling and coring of well 9 with oil-base mud in hole and was the source of much of the information used in preparing this publication. Of the eleven wells, four were drilled with rotary tools and water-base mud (one of the water-base muds was an oil-in-water emulsion mud), five were drilled with cable tools with brine in the hole, one was drilled with cable tools with brine in the hole and later reamed with rotary tools and crude oil, and one was drilled with rotary tools and oil-base mud. Although all of the wells penetrated sandstones that contained oil and gas, some were productive and others were not. The latter two wells, one completed with crude oil in the hole (with some added brine) and the other with oil-base mud, had the greatest productive capacities. The wells drilled with cable tools and brine in the hole had lower productive capacities. In contrast, two of three wells completed with rotary methods and fresh-water drilling mud and the well com¬pleted with rotary and emulsion mud were unproductive.

Jan 1, 1960

By Thomas J. Albin

This U.S. Bureau of Mines report identifies potential causes of slip-and-fall accidents occurring during surface mine equipment maintenance and describes the relative roles of direct worker behavior and machine design. The relative roles of human behavior and machine design in the causation of slip-and-fall accidents were determined through analysis of accident records, observations of maintenance worker behavior, and evaluation of mine machinery. From these data, relative risk ratios were calculated. Behavior had a relative risk ratio of 1.5; machine design, specifically access systems design, had a relative risk ratio of 2.2. Of the access systems, ladders had the highest relative risk ratio, 7.0. This study suggests that accident intervention would be most profitably made in improving the design of systems used to access maintenance worker areas of mining equipment.

Jan 1, 1990

By D. A. Reynolds, J. D. Davis

"This work was begun in l928, with the cooperation of the American, Gas Association, and the Association contributed financial aid for that year and for the 4 years following. In 1933 financial aid was discontinued, but the Advisory Committee, under the able, Chairmanship of J. S. Haug, has continued to function through the years to the present date. Mr. Haug's annual reports have been published in the Proceedings of the American Gas Association. The purpose of this paper is to bring the index of coals tested by the Bureau of Mines-American Gas Association (EM-AGA) method up to date, to discuss development of auxiliary tests, and to outiline the uses to which the methods have been put in promoting the war effort.COALS TESTEDThe test methods developed with the advice of the Advisory Committee had been applied to 66 coals up to 1942, and an index giving the serial number, origin, and analyses of these coals was published as Bureau of Mines Technical Paper 637. Since this paper was published, 20 additional coals have been tested; the source and analyses of these coals are given in table 1. The table also refers to publications that have been issued. Complete series of tests at high, medium, and low temperatures,have been made on most of these coals, and blending tests with 20 and 30 30 percent of low-volatile coals have also been made at 900°C.; however a few low- and medium-volatile coals (60, 70, 74, 79, and 80) were bested,at high temperatures only. Those coals were mined in eastern Oklahoma and western Arkansas. The test work included low- and high-temperature assay tests, petrorraphic analyses, and plasticity tests since its inception; and for the last 20 coals of the series, expansion and oxidation tests have been made where applicable."

Jun 1, 1944

By I. AITKENS

Turquoise is prized solely for its attractive color ; it is dull and opaque , wholly lacking the brilliant luster that is the chief attraction of transparent gems . The best quality of turquoise is blue , of a soft and pleasing tone , like the color of clear sky but distinctive , as indicated by use of the term " turquoise blue . " Often its value is lessened by a greenish cast ; in many stones the green predominates . A large proportion of the turquoise that is mined is utterly worthless , so inferior and unattractive is its color . The finest grade of turquoise comes from Persia , notable from Nishapur . Large quantities have been mined in the Southwestern States of the United States , and less important deposits have been found in a number of the other States .

Sep 1, 1931

By L. A. Haas

S02 reduction with CO was studied in an integral flow reactor at a nominal flow of 0.5 liter per minute. Reactant gas contained 3 percent SO2, 6 percent CO, and the balance He. SO2 conversion was determined for three different types of catalysts. The first consisted of 16 commercial catalysts used for various chemical syntheses. Only the commercial catalysts which contained transition metals in alumina removed more than 30 percent 80a at temperatures below 510° C. Two other types of catalysts were prepared in the laboratory either by pelletizing equal amounts of powdered alumina and transition metal oxides or by impregnating commercial alumina tablets with transition metal ions. Regardless of preparation techniques, Cr and Fe in alumina were the two best catalysts. The observed results suggest that an intermediate (SCO) is formed by the interaction of surface metal sulfides and carbonyls. Alumina then catalyzes the interaction of SCO with S02 to form the end products (sulfur and carbon dioxide). Over 80 percent S02 was removed at 460° C with 2 grams alumina impregnated with 2.5 percent iron.

Jan 1, 1972

A symposium on the health hazards of respirable dust in the mining and milling of talc was held on May 8, 1973, in Washington, D.C. The results of medical effects on both human and animal subjects were presented. Methods for identification and classification of talc minerals were also presented. Analytical techniques discussed included X-ray diffraction, scanning electron microscope observation, electron probe, and optical microscopy.

Jan 1, 1974

By William H. Schiffbauer

The U.S. Bureau of Mines has been investigating methods and technology that may improve safety and production when applied to existing mining machines. Toward those goals, the Bureau has developed navigation systems that provide machine positional information while in the production area. This research has been limited in the past because the Bureau had only one type of mining machine to do experiments. Addressing this problem, the Bureau, along with Carnegie Mellon University, has developed a generic vehicle emulator, in the form of a wheeled vehicle with an onboard computer, known as the Locomotion Emulator, that provides a software-selectable vehicle emulation package. Preliminary testing by the Bureau has shown that the emulator can accurately imitate the maneuvers of the software selected vehicle type. Now the Bureau can test their navigation systems on different vehicle types without having to procure each of the vehicles. This report completely describes the emulator as well as all the modes in which it can be operated.

Jan 1, 1991

By M. M. Tilman

The Bureau of Mines evaluated corrosion resistance of Split Set friction rock stabilizer mine roof bolts to aid in better prediction of useful service life. Electrochemical corrosion testing was conducted utilizing an automated corrosion measurement system. Natural and/or synthetic mine waters from four uranium and two copper mines were the test media for the two types of high-strength, low-alloy (HSLA) steels from which Split Set stabilizers are manufactured, and for galvanized steel. Tests were conducted with waters of minimum and maximum dissolved oxygen content at in-mine water temperatures. Retrieved Split Set stabilizers were also evaluated for property changes. Galvanized steel was found to be far superior to the unprotected steel in general corrosion resistance; limited tests indicate little ten.dency to pitting, contrary to behavior for the uncoated steel. Copper-bearing HSLA steel was slightly more corrosion resistant than non-copper-bearing HSLA steel. Statistical analyses resulted in development of equations relating dissolved oxygen, chloride, sulfate, and magnesium contents of mine waters to corrosion rates of the two HSLA steels (nongalvanized). An equation was developed that relates corrosion rates of galvanized steel to mine water temperature and dissolved oxygen content. Variable conditions in mine environments make corrosion damage difficult to predict and emphasize the need for corrosion prevention and control.

Jan 1, 1984