Search Documents

By A. Sainato, S. J. Kravits, G. L. Finfinger

This report describes a project conducted by the Bureau of Mines in which the accurate directional drilling of a borehole was demonstrated with the objective of intercepting a designated target. The project was conducted at Navajo Dam in northern New Mexico at the request of the Bureau of Reclamation. Borehole survey and drill logs are provided in an appendix. The trajectory of the demonstration borehole was designed to intercept a 5-ft-radius target at the final or "punchout" distance of 885 ft. The elevation of the borehole at this distance was within the target; the borehole punchout coordinates were 8.81 ft southwest of the target. As a result of the demonstrated accuracy, the Bureau of Reclamation has contracted the accurate drilling of boreholes as long as 600 ft from the inside of a short tunnel, to control water seepage in the right abut- ment. This resulted in a substantial cost savings compared to the orig- inal plan of constructing a longer tunnel and drilling 150-ft boreholes.

Jan 1, 1987

By E. R. Palowitch

Coal wasted with mine refuse represents losses in overall recovery of merchantable coal to the mine operator and a concomitant reduction in domestic reserves of available coal. Fraser, Kelley, and Graham3/ in studying the available coal in mine refuse in the Pittsburgh district of western Pennsylvania have estimated that at least 1 ton of mine refuse is produced for each 10 tons of merchantable coal and that 20 percent of this mine refuse might be recovered as salable coal by mechanical cleaning. SUMMARY This investigation dealt with the mechanical recovery of coal from wine refuse by a dense-medium washery employing pulverized mine rock as the dense medium and operating at a rate of 175 tons per hour. Two types of mint refuse were tested: Freshly mined and that .which had been mined 2 years before and piled on a waste dump.

Jan 1, 1955

By M. J. Sapko

The pressure and flame development of the methane-air-nitrogen system was investigated in the Bureau's l2-foot-diameter sphere to define buoyancy effects and to develop relationships for predicting venting requirements. Pressure rise (?P) is defined as a function of time (t) and nitrogen dilution and is shown to deviate noticeably from the cubic law (?P = kt3), depending upon the period of combustion and the mixture composition. Corresponding flame speed (Sf) and burning velocity (Su) data are given which show that Sf is time dependent and that Na dilution has a greater effect than air dilution in inhibiting the flame propagation. The Su data agree with "accepted" values and are unique in that they are based on much larger flames than those used in other investigations. Downward propagation limits are shown to depend mainly upon buoyant forces, which can affect the burning of even stoichiometric CH4-air systems. Theoretical expressions, based on the mixture burning velocity and expansion ratio, are given for predicting the venting requirements for ignitions of hydrocarbon-air-nitrogen mixtures in spherical or cubical enclosures.

Jan 1, 1976

By V. A. Nieberlein

The purpose of this investigation is to determine the reserves of columbium (niobium) minerals in Arkansas and to develop metallurgical methods for concentrating the minerals and extracting the metal. The columbium resources of central Arkansas were explored by drilling and trenching, and a number of samples were taken. On the basis of this exploration the known reserves of the metal were estimated to be over 78,000,000 pounds. The reserves could possibly be extended by additional exploration to 150,000,000 pounds.

Jan 1, 1954

By G. H. Wigton

This paper, describing the concentrator practice of the Chief Consolidated Co., is one of a series being prepared by the United States Bureau of Mines. The concentrator adjoins the town of Eureka, Utah, in the Tintic mining district. The Chief Consolidated, Eureka Lilly, Plutus, and Grand Central mines, all of which are owned or controlled by the Chief Consolidated Mining Co., are the principal sources of milling ore. The ore is transported from mines to mill by railroad. Although all the mines are within 3 miles of the mill, the railroad distance varies from 1 mile to 12 miles.

Jan 1, 1930

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing cloy reining, crushing, and grinding methods and costs at various operations throughout the United States. These Toners are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production casts. Although the publication of total production cants might not be advisable in sore instances, yet a knowledge of operating costs is essential to the technical discussion end study of the methods employed. The attention of the reader is specifically coiled to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The following report deals specifically with the methods employed by the Clay City Fire Co., Uhrichsville, Tuscarawas County, Ohio.

Jan 1, 1936

By John J. Henn

As part of the U.S. Department of the Interior programs on rutile, authorized by the Office of Emergency Preparedness in June 1967 under provisions of the Defense Production Act, the Bureau of Mines reviewed available literature on major proposed processes for producing rutile substitutes. The processes are grouped according to the major processing step, and important operating features are described. Sixty-one references are cited.

Jan 1, 1970

By Lloyd Williams, H. K. Gibbs, William L. Crentz, J. W. Miller

"Reserves This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds.Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal are estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Scott County, as determined by this investigation, is 52.4 percent. This percentage is based on the total thickness of coal in the bed (less partings three-eighths inch or more thick) rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Scott County, the recoverable reserves of coal are estimated to be 39 million tons as of January 1, 1954.Coal Analyses Chemical analyses of coal samples taken for this study show that the coal in Scott County is of high-volatile a bituminous rank except the Upper Pioneer bed, which is shown to be high-volatile B bituminous. The Pewee bed shows typical low-sulfur characteristics. The high ash and sulfur in the Big Mary are characteristic of that bed. The Poplar Creek is moderately low in ash and sulfur in areas where there is no parting in the bed."

Jun 1, 1956

By J. W. Town

This report summarizes the results of laboratory investigations conducted by the Federal Bureau of Mines to obtain hydrometallurgical information on the dissolution of mercury sulfides from ores, flotation concentrates, and pure mercuric sulfides. Statistical methods were used to design the experiments and evaluate the resulting data. Studies demonstrated that cinnabar is readily soluble in sodium sulfide, partly soluble in potassium sulfide, and essentially insoluble in ammonium sulfide. Additions of sodium hydroxide or potassium hydroxide to sodium sulfide solutions increased mercury extraction slightly; when either was added to potassium sulfide or ammonium sulfide solutions, mercury extraction was equal to that of sodium sulfide. Tests at the Albany Metallurgy Research Center showed that sodium sulfide would completely dissolve chemically pure mercuric sulfide, more than 95 percent of the cinnabar in 5-percent mercury flotation concentrates, and 60 to 90 percent of the cinnabar in low-grade ores. The double-leach tests showed that potassium sulfide would dissolve over 90 percent of the arsenic in mercury-arsenic products and 1 to 10 percent of the mercury; then sodium sulfide-hydroxide solutions would dissolve 80 to 90 percent of the remaining mercury and 5 to 10 percent of the arsenic.

Jan 1, 1961

By M. L. Whisman

Three samples of waste lubricating oil were re-refined by processes developed by the Bureau of Mines and reformulated with additives to meet designated requirements for viscosity and service. Quality-defining bench-scale tests were used to compare and evaluate the quality of these three motor oils, eight commercially re-refined lubricating oils, and three new lubricating oils. Most of the re-refined oils studied could not be distinguished from new oils by the bench tests used to define quality. There was some evidence, however, that one and perhaps more of the re-refined products investigated might not meet all of the quality standards of new lubricating oil, suggesting the need for better quality controls by re-refiners.

Jan 1, 1974

By Doerner H. A.

From thermodynamic calculations Maier predicted that zinc oxide and methane would react at specified temperatures substantially according to equation (1). (1.) ZnO + CH4 = Zn (gas) + CO + 2H2. Other reactions that may take place are (2.) CH4 = C + 2H2. (3.) ZnO + CO = Zn (gas) + CO2. (4.) ZnO + H2 = Zn (gas) + H2O. Maier predicted that 870°C would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C. Theoretical considerations indicate that reaction (1) is reversible: this is supported, but not proved, by experimental data. The other reactions are known to be reversible. At low temperatures reaction (2) requires a catalyst and it is slow below 1000°C. Reactions (3) and (4) are rapid, but the equilibrium constants are such that only small concentrations of CO2 or H2O can be produced below 1000°C. Maier calculated that CO2 should not exceed 0.5 per cent at 870°C., and the calculation for water vapor gives a still smaller order of magnitude.

Jan 1, 1931

By C. W. Owings, L. D. Tracy

"IntroductionMany bituminous coal-mining companies have inaugurated extensive safety Programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania.Story of the ExplosionAt about 10 o'clock on the night of the explosion an examination was made in No 2 butt left and parallel off 7o. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of Po. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 18 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air an explosion occurred.The helper dropped to the floor and was burned about the face and wrists. The machine operator ran down the entry and was more severely burned about the face, neck, and arms. He later developed pneumonia and died. Both men reached the door in the chute between No. 14 and No. 15 north. A pumper, who had felt the rush of air, found the men and helped them to walk outside."

May 1, 1927

By W. D. Ryan

The organic act passed by Congress in 1910 instituting the Bureau of Mines provided that the director of the bureau should promulgate such investigations as might be necessary to determine the causes of mine accidents and the best methods of preventing them. With the object of accident prevention in view, Director Joseph A. Holmes, and others who were pioneers in the bureau, conceived the Plan of having first-aid and mine-rescue training as one of the major activities of the Bureau. Out of this plan grew the first-aid and mine-rescue contests, which have been featured as an incentive for men to take courses in this type of mine safety training. The first appropriation for mine-accident investigations became available on July 1, 1908, under the jurisdiction of the U. S. Geological Survey, with Dr. J. A. Holmes in active charge. During 1908 there had been some first-aid training in the Pennsylvania anthracite field and a start made in Illinois, although there appears to be no exact information as to when or where first-aid training in the mining industry first became a reality, it is generally conceded that the St. John's ambulance corps of Scotland was one of the first - if not the first - to make the work effective. In 1911, to celebrate the establishment of the Bureau of Mines and the formal opening of the Pittsburgh, Pa., station, a first-aid and mine-rescue demonstration was conducted on Forbes Field, Pittsburgh. President William Howard Taft and many other men notable in public life were 2 resent. This was the first general national contest of the kind held it the United States; and since then there have been a number of nation-wide first-aid and mine rescue contests, as well as some which have been international in scope. There are over one hundred first-aid and mine-rescue contests of various kinds held annually in connection with mining and the allied industries.

Jan 1, 1929

By J. D. Davis

On May 15, 1936, Congress authorized the Bureau of Mines to conduct certain studies, experiments, and investigations of subbituminous coal and lignite .4/ Appropriations were made in July 1937, and since that date an active investigation has been underway to complete the provisions of the act. Part of the investigation has included a comprehensive survey of the known properties of the lower-rank non-coking coals, and provisions were made to obtain more data on certain varieties. In line with this plan, a typically subbituminous coal was selected for an extended series o tests in the standard Bureau of Mines-American Gas Association unit,5/ at the Central Experiment Station. This particular noncaking coal was the first one of its rank that ha& been tested in the apparatus; for this reason the results are of particular interest because the testing apparatus was originally designed for use in studying the coke- and gas-making properties of coking coals. The test as described below has been developed by the Bureau of Mines since 1927 through a cooperative agreement with the American Gas Association.6/ Ninety to 180 pounds of coal is heated in a circular retort, 13 to 18 inches in diameter, at wall. temperatures ranging from 540°C. to 1,110°C. in 100°C. steps. All products axe collected and measured; their physical and chemical properties axe then carefully determined to ascertain the gas- and coke-making properties of the coal.

Jan 1, 1939

By C. C. Knox

In Kiowa County, Okla., extensive deposits of clay are closely associated with pre-Cambrian anorthosites and gabbros. Investigation by the Bureau of Mines, including 1,723 feet of auger drilling, has shown the presence of very large quantities of clay containing between 20 and 25 percent alumina. All of the material contains large amounts of impurities, and even the best clays, selected for their relatively low content of iron, titanium, and magnesium, are unsuitable for the production of alumina by the sulfuric-acid process The soda-lime process gave somewhat better results, the product being nearer specification for commercial alumina. The clays are not amenable to beneficiation by simple sedimentation processes, and the alumina content could not easily be increased to produce material suitable for any alumina process.

Jan 1, 1948

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

By C. A. Taylor, C. E. Munroe

"In blasting the explosion of the high explosives charge is initiated by means of a detonator. Consequently the successful operation of the whole system is, ab initio dependent upon the suitability and efficiency of the detonator used. A considerable number of methods for testing the efficiency of detonators have been devised. In a previous publication*** of the Bureau of Mines many of these were discussed after having been classified as direct and indirect methods.In 1910, W. O, Snelling, then explosives chemist of the Bureau, devised a direct method which depends on the extent to which a hard brittle material of uniform granulation, such as quartz sand, is pulverized by the explosion of the detonator when imbedded in it, and, as a container in which to carry out the tests, he devised the vessel known as the Bureau of Mines sand-test bomb No. 1. A brief mention of his work was made in a paper presented to the Engineers' Society of Western Pennsylvania.****Later Storm and Cope made a very extended investigation of this method using sand-test bomb No, 1. Their paper***** contains a detailed, illustrated, description of sand-test bomb No. 1, with precise specifications of the sand and a minute account of the technique followed, together with a discussion of the data they obtained from the tests in this bomb of 112 detonators representing each of the grades from We, 3 to No. 10, inclusive. The average of results obtained by them are set forth in the following table."

Dec 1, 1923

By Fred Hodges

This paper describing the concentrator practice of the Hurley Plant of the Nevada Consolidated Copper Co. at Hurley, N. Mex., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Hurley concentrator has a normal daily capacity of 13,500 tons of ore, and for the first four months of 1930 the heads of the concentrator averaged 1.32 per cent of copper and 3.14 per cent of iron. The recovery for this period was 83.98 per cent and the concentrates produced averaged 27.54 per cent of copper.

Jan 1, 1931

Objective: On-the-job training (OJT) is a common means of training workers. By definition, it seems relatively simple. However, to be effective, training must go beyond the simple process of following an experienced worker around the workplace— sometimes called the "follow Joe" method. NIOSH researchers spoke with human resources personnel, safety and health specialists, supervisors, experienced miners, and new miners and found that OJT was of high interest, but was rarely part of a formal or standardized program. Various training methods have evolved to ensure that a trainee will absorb the information presented rather than simply emulate what the instructor is teaching. These methods have been brought together into a published guide for developing an effective formalized OJT program. The guide (Information Circular (IC) 9479) is called "Coaching Skills for On-the-Job Trainers." It contains materials and suggestions for your company or mine to conduct a 1-day workshop for teaching OJT trainers how to be better coaches to less experienced workers. The guide was created by the NIOSH Pittsburgh Research Laboratory and a safety professional from a private mining company.

Feb 1, 2006

By G. L. Oldright

This paper is the second of a series that is to appear on smelting in the lead blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation, and to correlate the behavior of the furnace at various times with the main factors governing the operation of the blast furnace, and metallurgical losses. The writers wish to express their appreciation to the management of the International Smelting Company at Tooele. Utah, for their kind cooperation which made possible the assembling of these data.

Jan 1, 1929