Search Documents

By Albert E. Long

Preliminary experiments conducted in 1949 with a few diamond bits in which the diamonds in the bit crowns were set in hard-vector directions indicated that a substantial saving could be effected when a high percentage of the diamonds were oriented in this-manner. It was realized, however, that many additional tests would have to be performed before a positive trend could be established and the possibility of coincidence eliminated. Therefore, a long-range series of experiments was planned to investigate various phases of the problems related to the orienting of diamonds in diamond bits. This report (the third in a series) 2/3 presents the information obtained from tests conducted to investigate more fully the effects of orienting high-grade drill bort in diamond bit crowns. In these tests, the drill bort were oriented in both hard-vector and soft-vector directions in the crowns of AX-size bits. Test drilling was done in a dike of saussuritized dacite porphyry similar to a fine-grained granite in hardness e drillability.

Jan 1, 1954

By Pedro Lilienfeld

The objective of this program was the development, design, and fabrication of six personal-sized completely self-contained dust monitors capable of real-time as well as time-averaged monitoring of the concentration of respirable particles in coal mines, in the range of 0.1 to 100 mg/m3. The operation of these monitors is based on light scattering and passive air sampling. The design stressed overall miniaturization, ruggedness, simplicity and versatility. These instruments incorporate a single-chip CMOS microprocessor to perform all signal processing, data display and storage, and timing functions. The overall dimensions of these devices are, approximately, 10 by 10 by 5 cm.

Jan 1, 1982

Treat contaminated coal mine drainage to meet EPA and State water quality requirements. Approach A model (fig. 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of abandoned mine lands (AML). The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions.

Jan 1, 1992

By Gary A. Kingston

Chromium resources in the United States are estimated at 1.8 million tons of recoverable chromium contained in 22.5 million tons of chromite-bearing material. Additional resource is presumed existent in large, but as yet undetermined, quantities of material containing less than 10 percent Cr203. No domestic resources are being mined presently (1969). Excluding transportation charges to domestic consuming areas, the total 1.8 million tons of chromim is estimated to be available, in ore or concentrate, at costs up to $0.64 per pound; 63 percent of the total is available under $0.11 per pound; and 38 percent under $0.08 per pound. It is judged that transportation from the resource areas to the existing market centers would add nearly $0.05 to the cost of a pound of chromium contained in ore or concentrate. Technically effective beneficiation methods have been developed for much of the known domestic resource, and further development might reduce costs of processing these materials. However, at present, domestic chromium resources are noncompetitive with foreign sources.

Jan 1, 1970

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

To increase safety and productivity in mining , the potential uses and hazards of rigid foam were investigated by the Bureau of Mines Experimental Coal Mine . This research resulted in the development of chemical formulations , spraying equipment , and application procedures that permit safe and effective use of urethane foams for improving mine ventilation , for reducing weathering of mine rock and steel , for constructing seals in fire areas , and for thermal insulation .

Jan 1, 1964

By Robert Hall

The Lynch Creek beryllium-tungsten prospect was investigated as part of the domestic beryllium resource studies by the Bureau of Mines. This prospect is in the Birch Creek mining district, Lander County, Nev., 9 airline miles south of Austin. A tungsten mine was operated intermittently from 1952 to 1957. Beryl was identified in the pegmatite dikes in 1960, and the lode claims were relocated. No beryl has been produced. Rocks in the area are Paleozoic sediments2 cut by pegmatite and aplite dikes and quartz stringers. Beryl occurs in random pockets, as disseminations throughout the dikes, and in occasional pockets in the quartz stringers.

Jan 1, 1962

By Peter N. Gabby

In 1990, the Bureau of Mines conducted a mineral resource investigation of the 12.321 acre Black Warrior study area, one of several proposed additions to the Sawtooth Wilderness. No identified mineral resources were delineated. There were 123 lode and placer claims in or adjacent to the study area. There is a known hot spring adjacent to the study area, but presently no geothermal leases are pending. Lode mines in pr adjacent to the Black Warrior study area have produced 4,022 tons of ore from which 1,981 oz of gold and 811 oz of silver were recovered. None of the vines are currently active. During the field study 125 rock samples were taken. Significant gold assays and favorable geologic characteristics at seven properties indicate that gold occurrences and resources with byproduct metals may exist in the study area. Two other sites yielded anomalous gold assays; however, sage favorable geologic characteristics are lacking. Presently, identified gold resources are being delineated by drilling programs in the nearby Atlanta and Rocky Bar mining districts. These districts have geologic characteristics similar to the Black Warrior area. During the field study 22 placer samples were taken. In most places where an anomalous concentration of gold was found, the stream channels are too narrow for operations other than recreational suction dredges. However. One area is estimated to contain over 2 million yd3 of gold-bearing gravels.

Jan 1, 1992

By V. B. Dale

This is one of a series of reports covering the mineral resources of the Nation. It describes briefly most of the known tungsten deposits in Yuma, Maricopa, Pinal, and Graham Counties, Ariz. Most of those described were examined by the author. An effort was made to determine the position of the various deposits by section, township, and range and to give accurate road direction to each property from a prominent landmark. All available maps have been used in making these determinations, but in unsurveyed areas it was necessary to make approximate projections of subdivisions. The township and range numbers refer to the Gila and Salt River base and meridian.

Jan 1, 1959

By Benjamin W. Haynes

The Bureau of Mines, in cooperation with the National Oceanic and Atmospheric Administration (NOAA), has updated a 1977 NOAA report prepared by Dames & Moore entitled, "Description of Manganese Nodule Processing Activities for Environmental Studies." This updated report contains detailed flowsheets and descriptions of the five potential first-generation nodule recovery schemes now considered most likely to be used by industry; they are high-temperature gas reduction and ammoniacal leach, Cuprion ammoniacal leach, high-temperature and high-pressure H2S04 leach, reduction and HCI leach, and smelting and H2S04 leach. The first three processes are three-metal recovery schemes (Cu, Ni, and Co) with the option of Mn recovery from the tailings. The remaining two processes are four-metal (Cu, Ni, Co, and Mn) recovery schemes. All except the HCI process are assumed to use a nodule feed rate of 3 million tons per year (dry basis). Final metal products are Co powder and cathode Cu and Ni. A minor amount of Ni is also recovered as powder, and some Cu and Zn are recovered as mixed sulfides. Manganese in the four-metal processes is recovered as either manganese metal or ferromanganese.

Jan 1, 1983

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1978 and 1979 was 8831.8 million and $336.4 million, respectively. In 1978, nearly all commodities registered an increase in production and value; unit value increased for all commodities, with the exception of native asphalt and sand and gravel. Alabama led the Nation in the production of crushed marble and was second in bauxite, third in masonry cement, kaolin, native asphalt, and oyster shell, and fourth in bentonite, dimension marble, fire clay, and scrap mica. Trend; and Developments.-The Alabama State Docks at the Port of Mobile handled more than 10 million tons of bulk material in fiscal year 1978; volume dropped slightly to 9.8 million tons in fiscal 1979. Bulk materials comprise the major activity at the facility, with iron ore and bauxite being two of the major materials handled. The movement of these ores is vital to the operation of many heavy industries in the State.

Jan 1, 1981

By Douglas A. Elkins

The unique characteristics of plasmas, their current applications, and ongoing research into new applications are described. Major technical and economic problems in application of plasma technology are discussed. Examples of potential applications of plasma in extractive metallurgy are described and evaluated. The report includes a selected bibliography of articles on plasma and related high-temperature technology.

Jan 1, 1969

By G. W. Reimers

Exothermic oxidation reactions of sulfide minerals can produce self-heating situations in underground mines. If the self-heating is unchecked and the resulting heat is not sufficiently dissipated, the result can be spontaneous combustion fires. This U.S. Bureau of Mines report describes laboratory tests conducted to measure the reactivity of pyrite following treatment with additives to counter its self-heating tendencies. Thermal gravimetric analysis (TGA) and isothermal oxidation procedures were used to obtain information on pyrite ignition and the behavior of pyrite during low-temperature oxidation to ferrous sulfate. The determination of treatment effectiveness was evaluated by adding 5 wt pct of the compound to the pyrite before milling. The resulting samples were then heated in moistened air and after 24 h, the amount of pyrite oxidation determined. Results of these tests indicated that several phosphate compounds reduced the oxidation of pyrite to sulfate to about 50 pct or less compared with the oxidation of untreated sample at 200° C. Cupric sulfate reduced oxidation to about 20 pet untreated sample at 200° C. Sodium, calcium, and potassium chloride reduced pyrite oxidation to levels of approximately 15 pct or less of the untreated sample. Using only 1 pct of sodium or calcium chloride was effective in slowing pyrite oxidation to less than 20 pct of the untreated sample.

Jan 1, 2010

By Thomas J. Blalock

The volumetric determination of uranium according to the method of Sill and Peterson (6),3/ which uses cerate oxidimetry after the separation of interferences such as sulfides and cupferrates, has been used for some time by the Bureau of Mines and gives satisfactory results for many of the samples tested. However, in those instances where the uranium content did not exceed a few tenths of 1 percent and iron was present in the range of 10 to 40 percent (as Fe203),4/ the method was cumbersome and unreliable. The need for a more accurate procedure for the determination of small amounts of uranium in the presence of large amounts of iron, such as in shale or black sands, prompted this investigation. The Bureau desired that materials containing as little as 60 p.p.m. of uranium be assayed within reasonable limits of accuracy. One of the primary aims of this work has been to eliminate, as far as possible, the necessity for repeated cup ferron extractions.

Jan 1, 1960

By Paul M. Tyler

Syria is a federation of States under French mandate , comprising the Republic of Syria , the Lebanese Republic or Great Lebanon ( Grand Liban ) , the State of the Alouites , and the Djebel Druse Territory . Beirut is the center of government for the whole area , about 60,000 square miles . Syria is essentially an agricultural country . There is little manufacturing ; and with the exception of the production of asphalt and salt , the mineral industries have not yet risen to commercial importance . Whether this condition is due to a dearth of workable deposits or merely to insufficient exploration is not apparent . The mineral resources , as reported by various authorities , include asbestos , asphalt rock , bitumen , chromite , coal , copper , gold , gypsum , iron , lead , magnesite , manganese , marble and other building stones , nickel , ocher , pandermite ( a hydrous borate of calcium) , petroleum , phosphate rock , pyrite , salt , silver , sulphur , tin , and titanium ( ilmenitic beach sands ) .

Mar 1, 1933

By R. W. METCALF, A. G. Charles, F. M. SHORE

To furnish the information frequently requested by producers and suppliers as to the fuel requirements of the Federal Government , the Bureau of Mines , with the cooperation of the consuming departments and establishments , has collected the data herein , showing the Government's fuel consumption during the fiscal year ended June 30 , 1930. The following tables show the quantities and kinds of fuels consumed by the Federal Government in each of its departments and their principal branches , in each State , and in Alaska , Hawaii , Panama Canal Zone , Porto Rico , and the Virgin Islands . The separate departments and establishments were asked to supply information for each Federal building or other plant and , as to vessel fuel , the amount loaded at each port of supply . Fuels consumed in internal combustion engines are not included . The report does not include fuels used by Post Offices of the fourth class , since their fuels are not purchased by the Federal Government but are covered by an allowance in each case for light and heat . In some cases the data supplied represent receipts , which are approximately equivalent to consumption . The present study is believed to be the first effort to bring together the data representing the Government's requirements for the various fuels which it consumes . Figures showing the coal consumed by the Federal Government were gathered for the year 1922. These data are shown in an article by O. P. Hood and R. H. Kudlich of the Bureau of Mines , contributed as a chapter to " Industrial Coal ; Purchase , Delivery and Storage , " published by the American Engineering Council . The figures of coal consumption presented herewith are approximately comparable with those published for 1922 , a relatively small difference being due to the fact that the 1922 figures include the Philippine Islands and all other territory in which any coal was consumed by the Government . At the present time , the only data on Government fuel consumption that are published regularly are those compiled by E. B. Swanson , chief economist of the petroleum economics division of the Bureau of Mines . These are published annually by the Bureau of Mines in " Sources and Distribution of Major Petroleum Products , Atlantic Coast States , " and by the bureau in cooperation with the American Petroleum Institute in the annual " National Survey of Fuel Oil Distribution . " It is believed that the data herewith will prove of interest and value to the fuel industries as well as to Government consumers and that it will also afford a basis for measuring future trends in the use of the various fuels by the Federal Government . Figures showing the quantities of the various kinds of fuels consumed by each of the executive departments and independent establishments , are given in Table 1. It should be noted that when one organization procures and delivers fuel to be consumed by other branches

Apr 1, 1932

By Robert W. Smith

Computation of the thermodynamic properties of the reaction products in the deflagration of explosive gas mixtures has been a most valuable guide regarding the possible kinetic mechanisms of homogeneous combustion processes. Knowledge of the physically possible end states is indispensable for understanding observed deviations from equilibrium in heterogeneous combustion. However such information on dust flames is entirely lacking. To complement a Federal Bureau of Mines study of stationary graphite dust flames burning in pure oxygen,6/ this report gives examples, at atmospheric pressure and room temperature, of composition profiles in an idealized oxygen-dust flame, with both mass and enthalpy being preserved. Similar profiles can be obtained from the data of the paper for elevated temperature and pressure.

Jan 1, 1960

By Ulrich Neumann

Mining coal by employing a method called longwall mining is gaining more and more popularity in the United states since it offers many advantages over the conventional deep mining methods. Those advantages are a higher productivity, an almost total extraction of the mineral since no pillars must be left behind for support, and an increase in safety since the personnel are protected by the shield supports and rarely have to work near unsupported, exposed root. However, on some longwalls, the dust levels liberated by various equipment such as belt conveyors, chain conveyors, crushers, longwall shearers, and moving shield supports can exceed the maximum permissible limits and therefore have an adverse effect on productivity. Many attempts have been made over the past years to reduce the dust liberation by changing designs, installing various types of sprays or scrubbers, treating the mine water with wetting agents, or even using foam to catch dust before it becomes airborne. In the year 1984, the Bureau of Mines awarded Eickhoff Corporation a contract to demonstrate a water-jet-assisted cutting system for the multiple purposes of reducing dust levels, improving bit consumption, and increasing material size. During the previous phases of this contract, various trials were conducted aimed to design, build, and test d shearer loader to meet the objective of the contract. In the early stages of the research program, it was expected to see a reduction in the overall power consumption of the machine due to the fact that the high-pressure water jet would pre-cut the mineral in front of the bit. This, in turn, would then reduce the bit wear. Since there is less cutting action performed by the bit, a reduction of the dust liberation and a reduction of product fines was sought.

Jan 1, 1991

By Michael A. Trevits

During the time period from 1990-2007, there were 1601 reportable fires that occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research addressing metal/nonmetal and coal mine fire prevention, detection, management and suppression. In the metal/nonmetal area, work was focused on technology transfer and training, and research to reduce the number of mobile equipment fires and their hazards. In the coal arena, research is underway to determine the root cause of cutting and welding-related fires and to evaluate the effects of ventilation schemes relative to the spontaneous combustion risk in longwall mines. Relative to fire management, research is ongoing on remote mine seal installation and remote mine fire suppression technologies. Finally, research is continuing to develop comprehensive and usable smoke management techniques and to develop mine fire growth models, propagation, and suppression. This paper presents a summary of some of the mine fire research and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2010

By R. E. Lindstrom

A study of ion-exchange resin crosslinkage and eluant flow rate, resin-bed shape, and addition of separating ions to feed stock was undertaken to determine their effect on the separation efficiency of ion-exchange on bastna-site-rare-earth elements. Results show that 12-percent divinylbenzene (DVB) crosslinkage resin is detrimental to separation efficiency at flow rates over 2 to 5 ml./min./sq. cm.; whereas, separation with 4-percent DVB crosslinkage resin is relatively unaffected by flow rates between 2 and 10 m1./min./sq.cm.

Jan 1, 1959

By R. L. Grant

Study of the ignition of firedamp by explosives and the phenomena that underlie it is one of the long-term investigations of the Bureau of Mines. This report is the third in e series by the Explosives Branch summarizing the progress made at Bruceton in this study. The first paper described preliminary work on small, carefully controlled cannon shots the second discussed the results of suspended shots.5/ In this paper, experiments are described and interpreted that extend and support the concept of ignition presented previously. ACKNOWLEDGMENT The authors wish to thank Bernard Lewis, former chief, Explosives and Physical Sciences Division, and Guenther von Elbe, former chief, Physical Sciences Branch, Explosives and Physical Sciences Division, for their guidance and constructive interest.

Jan 1, 1954