Search Documents

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By Robert J. Willard

This chapter includes tables from 1983 that were not available in time for publication of the 1983 Minerals Yearbook, but does not include corresponding tables for 1984. The value of raw nonfuel minerals produced in the United States during 1984 was estimated at $23.2 billion, an increase of $2.1 billion over the value for 1983. This is the second consecutive year that the value has increased, and except for a decrease in 1982, the value for each year has increased since 1971, or 12 out of 13 years. In 1984, 16 out of 21 metal commodities increased in output while 5 metals decreased; 14 metals increased in value and 7 decreased. Of 46 nonmetal commodities. 37 increased in output while 7 decreased and 2 remained unchanged; 35 nonmetals increased in value and 11 decreased. These statistics are grounds for continuing the cautious economic optimism expressed in 1983. Despite the note of optimism, however, numerous problems plague the mining industry, weakening its stability and inhibiting its growth potential. The problems are a complex mix of international and domestic factors that have been building in the recent past, but have become even more troublesome in 1984.

Jan 1, 1985

By J. H. Weber

This Bureau of Mines publication describes the hardware system and software package for the semiautomatic acquisition and automatic processing of high-resolution mass spectrographic plates. The semiautomatic data acquisition allows a tenfold saving of time compared with manual data acquisition. Automatic processing of the high-resolution data to yield exact masses, intensity, and the corresponding empirical formulas is accomplished by efficient programming on a small, inexpensive, programmable calculator system.

Jan 1, 1974

By Syd S. Peng

The design of retort interchamber pillars is important in determining surface stability over in situ retort mines and to the health and safety of miners, particularly with respect to possible escape of heat and toxic gases from retort chambers. Stress distribution in retort interchamber pillars, roof, and floor was examined with the aid of linear, finite-element analysis using data from experimentally determined mechanical properties. Properties determined included elastic moduli, strength, and creep constants in laboratory tests on core covering a 100-foot depth interval in the oil shale from the Piceance Basin in Colorado. The most critical stress concentration was found in the rib side of the interchamber pillar at a height above the floor line of 1.25 times the width. Guidelines for pillar design that consider pillar strength, creep, and retorting temperature effects are proposed.

Jan 1, 1981

By C. P. Bowie

[Frequent accidents in the transportation and. handling off petroleum and its more volatile products, serve as a reminder that this is indeed a hazardous undertaking and should always be conducted with due caution. On October 4, 1920, vapors in the held of the British tanks steamer G. R, Crowe became ignited and, caused an explosion which, it is reported, killed 5 men, injured. 40 others and endangered the lives of some 300 more. On November 10, 1920 the Morgan, Line freighter El Mundo was almost totally sot destroyed in New York harbor by fire caused by an explosion of gases in a fuel-oil tank. These two disastrous explosions emu emphasize the ever- present danger attending the use of petroleum products. This is also shown by the frequent occurrence of minor fires and explosions, caused by careless handling of baseline, which result in loss of life or serious injury to railroad employees, to oil-tank drivers, and to individuals in various walls of life. Statistics indicate that the lighter cuts of petroleum products, because of fire hazards, are dangerous, and are so considered by the railroad and other transportation companies. According o the Bureau of Explosives (Bar-eau of Explosives Report No. 13 p. 7) during 1919 transportation of gasoline in the United States resulted in 172 accidents, causing 2 deaths and 31 injuries, and a property loss to the extent of $687,966. Among the causes of ignition, an open light in the vicinity of the container stands out most prominently.]

Jan 1, 1920

By Paul T. Allsman

THIS CHAPTER reviews the highlights of developments in mining technology during 1956 and presents a special report on the design of mine openings in stable ground. This special report is presented each year in an endeavor to stimulate use of the scientific approach to the solution of problems related to mining technology. Assuming that the literature on mining technology reflects trends in mining, it appears that two areas of activity were given most attention in 1956. One was research on mining technology,4 and the other was improvement of transportation, particularly trackless transportation, both at surface and underground mines.

Jan 1, 1958

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

2. Preliminary Study - Initial Probing 2. 1 Introduction Initial probing of the mine passage is required prior to the emplacement of the sealant material or deployment of the seal checker system. Factors which are of interest in sealing and checking include a. size and condition of the mine passage b. location of the borehole with respect to the ribs c. the presence of water flows d. the proximity to an intersection The importance of each of these factors depends strongly on the sealant material. Because the sealant material had not been selected at the time of the initial probing study, a broad survey of probing techniques was conducted. The capabilities and limitations of each technique as they applied to probing through the borehole were identified. To facilitate this comparitive evaluation, Table I was prepared which lists all passage conditions which might affect the emplacement of sealant material in the passage. The most satisfactory techniques for observing each condition of interest are listed together with the effects of the observation on the sealing operation. Table II summarizes the environmental conditions likely to be encountered in the passage being probed and the physical

Jan 1, 1973

By D. B. Dow

The appearance of water in an oil field is the forerunner of various difficulties, and probably represents the greatest technical problem that the producer must face. Water conditions bear-directly on the quantity of oil recovered, and the length of the life of a field. Presence of mater increases the cost of operation, for example, gifting costs. On account of the corrosive action of oil-field waters on pumps and other equipment, frequent replacement of equipment is necessary. Furthermore, water may affect the marketability of the oil produced, as detrimental emulsions of water in oil (?B.S.?, "cut oil", etc.) are often formed. The writer has recently completed a study of oil-field emulsions. The present paper deals with the factors responsible for the formation of emulsions. This will be followed by another dealing with methods now utilized for dehydrating oil-field emulsions, and by a third dealing with the physical chemistry involved in the formation and resolution of such emulsions.

Jan 1, 1925

By Raymond B. Ladoo

"The increasing realization of the fire hazards involved in the use of wooden shingles caused the National Lumber Manufacturers' Association to beginsome five years ago a search for a suitable fire-resistant paint. The problem was submitted to the Educational Bureau of the Paint Manufacturers' Association of the United States and work was started by Mr. Henry L. Gardner at the Institute of Industrial Research, Washington D.C. in collaboration with Dr. Herman von Schrenk, a timber expert of St. Louis.The results of this,work have been described by Heckel, in ""Asbestos"", (Heckel G.B., Asbestos in the Paint Industry, Asbestos, Vol. 2, July, 1920,pp.- 5-10).,,who gives the following formula for one of the colors as typical: It will be noted from this formula that ""asbestine"" forms 33% of the total liquid pigment by weight or 31.8% of the solid constituents. Hockel in the article referred to describes this paint,as ""asbestiform"" and assumes since ""asbestine"" is magnesium silicate it must be the chrysetile variety of ""Asbestine"", however, is not asbestos but is a trade name for a fibrous variety of talc mined in the Gouverneur district, St. Lawrence County, New York. This rather natural error persists through the article and credits asbestos with many desirable properties which are characteristics of talc."

Aug 1, 1920

By J. M. Riley

A fluorometric method using morin in an alkaline-buffered chelating solution has been developed by the Bureau of Mines for determining beryllium in ores and mill products. Apparatus for measuring fluorescence intensities of the beryllium-morin reaction is described. Preparation of the sample for analysis consists essentially of digestion with sulfuric, nitric, and hydrofluoric acids, fusion of the residue with sodium carbonate and sodium borate, Solution of the melt with sulfuric acid, and proper dilution. Chemical separation of other ions is usually unnecessary. The method rave reliable beryllium determinations on samples in the 0.01- to 0.37-percent BeO range. The method is particularly applicable to low-grade beryllium ores; however, semiquantitative beryllium determinations have been made on beryl containing 12.0 percent BeO.

Jan 1, 1956

By W. C. Hudson

"The McLeod sand pits, on the northeast side of the Little Ocmulgee River in Wheeler County, Ga., opposite Lumber City in Telfair Co., were examined by the Bureau of Mines under its war program of Investigation of Critical and Essential Minerals. The pits are about a quarter of a mile above the bridge, which is half a mile above Lumber City. Mrs. A. T. McLeod of Lumber City owns the land, including the pits. The property was inspected by an engineer of the Bureau of nines on March 8, 1945, on recommendation of Capt. Garland Peyton, director, Division of nines, Mining, and Geology of Georgia.The Mcleod pits are at the northwestern extremity of a mile-long series of old pits that were worked from about 1900 until the 1920's. The burning of the spur railroad bridge connecting the pits with the Southern Railway at Lumber City stopped mining operations. The pits on the south-east, or opposite, side of the Glennwood Road from the McLeod pits were first worked by F. L. Hinson and later, in 1921, by Mrs. n. H. Mobley. The glass sand was shipped to Tallapoosa, Ga., and Chattanooga, Tenn., where it was used in the manufacture of bottles for soft drinks. Some of the sand was used as molding and construction material. The sand was mined by hand shoveling it into wheelbarrows, which were unloaded on freight cars. The pits were partly refilled with overburden, so that it is impossible to estimate even roughly the amount of sand excavated.Analyses of samples of glass sand made years age3/ and later in 19404/ roughly check those made by the Bureau of Mines laboratory, except that in the former the iron oxide content usually was greater, attaining a maximum of 0.72 percent.The sand pits are in a valley slightly more than a quarter of a mile wide that lies along the northeast side of the Little Ocmulgee River. The land is either flat or marked by ridges only a few feet high. . A rather thick growth of scrub trees covers most of the valley. The surrounding country consists of gently rolling farm lands. The altitude of the valley is not known, but, judging by its distance from the seashore, it probably is about 200 feet. In addition to the Glennwood highway, which crosses the valley, several old sand roads lead to the pits."

Apr 1, 1946

By E. G. Davis

The flash reduction of fine iron ore in a dilute-phase system was investigated at 500° to 900° C within a heated stainless steel tubular coil. Alabama brown iron ore and Mesabi semitaconite ore were fed into the coil concurrently with reducing gases of hydrogen and reformed natural gas, so that the velocity of the gas at the reaction temperature was sufficient to entrain and pneumatically transport the solids through the coil. Reduction is very rapid with retention time of the ore in the coil varying from 4 to 15 seconds. Variables affecting reduction are temperature, ore feed rate, and gas flow or velocity. Results of the studies show that a partially reduced product (10-to 25-percent reduction) can be made which, on subsequent magnetic concentration, yields a concentrate containing 64 to 70 percent iron with a 90-to 94-percent iron recovery. Maximum reduction of 77 percent was obtained when hydrogen was used in a four-stage reduction test to yield a product containing 61 percent metallic iron.

Jan 1, 1972

By H. F. Yancey

A relatively large proportion of the coal produced in the state or Washington, especially in the coking coal areas is of fine size; hence washing by means of coal-washing tables to reduce the ash content is commonly practiced. For this reason the program of research in coal washing conducted jointly by the U. S. Bureau of mines and the College of Mines, University of Washington, has given special attention to the mechanism of the separation of coal from its impurities as affected by the coal-washing table with the object of

Jan 1, 1931

By G. L. Finfinger, J. Cervik, L. J. Prosser

The Bureau of Mines has completed an underground degasification project in which an underground piping system was used to transport methane from the coalbed to the surface. In a 10-month period four horizontal holes were drilled to an average depth of 1,450 feet. All four holes were surveyed vertically and azimuthally. In 991 days of degasification, 255 MMcf of gas was drained from the coalbed. The underground piping system proved to be a safe and effective means of transporting methane from the coalbed to the surface.

Jan 1, 1981

By W. E. Robinson

Sixty samples, selected from a 2,300-foot core of the Green River Formation in Colorado, were studied to ascertain differences in the structure of the organic material present in the oil shale samples. Emphasis was placed upon relating differences in the aromatic content of the insoluble kerogen and the alkane content of the extractable material obtained from the selected samples. The methods used in determining these differences consisted of fractionation of the soluble material, carbon and hydrogen analysis, volatile material determination, carbon residue determination, oxidation rate determination, and infrared analysis. In general, it was concluded that the organic material in this core does vary in chemical structure and that same of these variations resulted from factors related to depth of burial. Other observed changes in structure of the organic material were not depth-dependent and resulted from other factors such as source material variations, biological alterations, or ecological differences.

Jan 1, 1971

By N. N. Moebs

The Bureau of Mines air-sealed a 77-acre) above-drainage coal mine to evaluate sealing as a means of reducing the acid and metallic salt contents in drainage from abandoned mines. An approximate reduction in acidity of 150 ppm (equivalent to 193 pounds per day) and in iron of 98 ppm were directly attributed to sealing. The topographical, hydrological, and other factors involved in air-sealing are discussed, and the construction used to seal the mine is described.

Jan 1, 1970

By Richard A. Thomas, Michael J. Sapko, Gary L. Mowrey, William D. Monaghan, Michael A. Trevits

Over the years, more than 20,000 mine seals have been erected in underground coal mines in the United States. Seals are used extensively in underground mines to isolate worked-out areas, active mine fire zones, and to control water inundations. Seals are most often built directly in the mine and can be fabricated from blocks made of wood or cementitious material. Recently, several explosions occurred within sealed areas of underground U.S. coal mines. These explosions, believed to be initiated by lightning strikes on the surface, destroyed numerous seals and caused considerable damage external to the sealed area. The National Institute for Occupational Safety and Health is conducting research to develop design guidelines, to investigate noninvasive techniques to characterize seal strength properties, and to evaluate seal test methods. As part of this work, a 30-ft wide, 16.1-ft tall and 4-ft thick seal was built in an underground experimental mine using cement and foamed water. Two types of noninvasive techniques are currently being investigated, namely the Schmidt Hammer for measuring compressive strength and ground penetrating radar (GPR) for detecting the presence of anomalies (e.g., voids, discontinuities) within the seal. Once these noninvasive tests were completed, the seal was subjected to destructive explosion testing. This study presents the results of the Schmidt Hammer tests, GPR scans, and the characteristics of seal failure during explosion testing.

By Theodore Kootz

Manufacture of high-grade ferromanganese; as a rule; requires a low-phosphorus-manganese ore with 45 to 55 percent Mn, chiefly obtained in the Soviet Union, the British Dominions, and Brazil. Also, low-manganese ores have already been used for ferromanganese production, especially in North America .and Germany. During World War I, a process was developed in which a high-phosphorus ferromanganese or spiegeleisen was prepared in the blast furnace from law- or high-phosphorus manganiferous ores, then low-phosphorus manganese slag was prepared by refining under an acid slag, and this material was, worked into a low-phosphorus ferromanganese in the blast furnace.9/ Manufacture of useful manganese ores from a phosphorus-bearing spiegel with 12 to. 15 percent Mn, 4.5 percent C,, and 0.5 percent P by slagging in a refining furnace was reported by Joseph, Barrett, and Wood.10/ The spiegel was refined to 0.75 percent Mn, 3.4 percent C, and 0.45 percent P. Thereby, a slag with about 43 to 58 percent Mn and, about 10 percent Si02, was obtained. Hotter melts gave a smaller phosphorus content in the slag than cold melts. In addition, the phosphorus content of the slag varied with the manganese content of the intermediate metal.

Jan 1, 1952

By d&apos, Kathleen J. Amico

THIS summary appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S mineral production also is included.

Jan 1, 1964

By Rudolf Kudlich

"The realization that fuel costs, high as compared with those enjoyed prior to the war, are apparently permanent, has caused steam power plant operators to apply their best efforts towards improving the fuel economy of their plants.Though they have given much attention to the reduction in combustion losses by improving methods of firing and improved equipment, and to diminishing the heat losses by more care in maintaining clean heating surfaces and tight and adequate baffling, they have almost universally neglected the waste that occurs from discarding unconsumed combustible with the boiler refuse.This loss varies between extremely wide limits, depending on the quality of the coal, the type of plant and the firing practice in general, the higher the ash content of the coal the greater will be the amount of combustible appearing in the refuse, and the losses will be greater as the boilers are driven at higher ratings. The refuse from stoker fired boilers is apt to have a lower aver-eve percentage of combustible than that from hand fired boilers if operated at the same rating, but stoker fired boilers are usually pushed to higher ratings and the combustible in the refuse will run higher.In actual operating practice the amount of unconsumed combustible in the boiler refuse may range from a few percent to as high as forty or fifty percent. In an informal statement one well known combustion engineer estimates that the average amount of combustible in the refuse from a large stoker fired central station boiler plant is about 15 or 20%. Assuming that the coal burned contains 12% of ash, and allowing for flue dust losses, approximately two percent of the coal will be lost through this channel. The operating engineer of one large modern central power plant reports that when burning coal of about the same ash content, the average amount of combustible in the refuse was in the neighborhood of 33%, en tailing a loss of approximately 4% of the heating value of the fuel fired. Where the coal used daily runs up into hundreds of tons, an appreciable economy could be effected by recovering this percentage."

Sep 1, 1924