Search Documents

By L. M. Sekhukhune

The atmospheric leaching of copper-bearing matte by acidic ferric chloride solution was studied at the laboratory scale. The aim was to achieve maximum copper and nickel recovery by investigating the mechanisms of leaching, as well as identifying the effect of temperature, and concentration of ferric chloride and oxygen. Djurleite (Cu1.96S), hazelwoodite (Ni3S2), and Ni alloy were the primary phases detected in the matte. The quantitative composition of the matte was Cu 31%, Ni 50%, S 13%. Fe and Co constituted 2%, with platinum group metals (PGMs) accounting for 0.5%. A maximum nickel extraction of 98% was achieved using two-stage oxidative leaching at 90°C and 11 g/L Fe3+ as compared to 65% under non-oxidative conditions. A copper extraction of 99% was achieved in the first 45 minutes using two-stage non-oxidative leaching, and copper was recovered from solution by cementation. Three processes took place simultaneously throughout the leaching process, namely: dissolution, cementation/ metathesis, and oxidation. The leaching process was found to be diffusioncontrolled.

Jan 1, 2014

By M. Kwasniewski, M. Takahashi

Prismatic samples of a medium-grained sandstone from Slask Colliery (Upper Silesian Coal Basin, Poland) were tested under uniaxial compression, conventional triaxial compression and true triaxial compression conditions. The conventional triaxial compression tests were carried out at confining pressure (p) equal to 12.5, 25.0 and 37.5 MPa. In the true triaxial compression tests the minimum principal stress (s3) was equal to 25.0 MPa and the intermediate principal stress (s2) was 1.5, 2 and 2.5 times higher than s3. Results of the studies show that confining pressure strongly inhibited dilatant behavior of rock samples tested under conventional triaxial compression conditions; the increasing confinement resulted in the growing compaction of the rock material. The effect of dilatancy was also highly suppressed by the intermediate principal stress. While important dilatant, negative volumetric strain corresponded to the peak differential stress at low intermediate principal stress conditions, at high intermediate stresses the rock material was damaged to much lesser extent. As a result, faulting of rock samples in the post-peak region was much more violent and was accompanied by a strong acoustic effect. Les échantillons parallélépipédiques du grès à grains moyens de la mine ‘Slask’ (Bassin Houiller de Haute Silésie, Pologne) ont subi les essais de compression monoaxiale (compression simple), de compression triaxiale conventionnelle (compression triaxale de révolution) et de compression triaxiale vraie. Les essais de la compression triaxiale conventionnelle ont été effectués à la pression de confinement de 12,5, 25,0 et 37,5 MPa. Dans les essais de compression triaxiale vraie la contrainte principale minimale (s3) était de 25,0 MPa et la contrainte principale intermédiaire (s2) était 1,5, 2 et 2,5 fois supérieure de s3. Il résulte des essais que la pression de confinement inhibe fortement le processus de dilatance dans les échantillons testés dans les conditions de compression triaxiale conventionnelle; l’augmentation de la pression provoquait l’augmentation du compactage du matériau rocheux. Le phénomène de dilatance était également limité de façon significative par la contrainte principale intermédiaire. Alors que l’importante déformation volumique négative correspondait à la contrainte différentielle ultime avec les faibles contraintes principales intermédiaires, dans les conditions de fortes contraintes intermédiaires, le matériau rocheux subissait l'endommagement de façon beaucoup moins importante. En résultat, la rupture des échantillons rocheux au stade post-maximum était beaucoup plus violente et accompagnée d’un fort effet acoustique. Prismatische Probekörper des mittelkörnigen Sandsteines aus dem Bergwerk ‘Slask’ (das Oberschlesische Kohlengebiet, Polen) wurden unter der einaxialen Druckbeanspruchung, konventionellen dreiaxialen Druckbeanspruchung und der echten dreiaxialen Druckbeanspruchung geprüft. Konventionelle dreiaxiale Druckversuche wurden bei dem Manteldruck von 12,5 25,0 und 37,5 MPa durchgeführt. Bei den echten dreiaxialen Druckversuchen betrug die kleinste Hauptspannung (s3) 25,0 MPa und mittlere Hauptspannung (s2) war 1,5-, 2- und 2,5-mal höher als s3. Aus den durchgeführten Versuchen ergibt sich, dass der Manteldruck die Dilatanzentwicklung bei den Probekörpern unter der konventionellen dreiaxialen Druckbeanspruchung stark bremst; die Erhöhung des Druckes rief die ansteigende Kompaktion des Gesteinsmaterials hervor. Die Dilatanz wurde auch durch die mittlere Hauptspannung beschränkt. Während die wesentlichen volumetrischen, dilatanten Verformungen der Grenzdifferenzspannung bei den niedrigen mittleren Hauptspannungen entsprachen, bei den hohen mittleren Hauptspannungen wurde das Gesteinsmaterial viel weniger beschädigt. Im Ergebnis war der Scherbruch der Gesteinsproben im Post-Peak-Bereich viel heftiger und mit kräftigen akustischen Effekten verbunden.

Jan 1, 2003

By F. Bonnet, J. Lehmann, H. Gaye

A review of thermodynamic information and models of slags, including associated software when available, is presented. The pertinence and accuracy of these models is discussed by comparison of their predictions for various slag thermodynamic properties with the available experimental data. Practical industrial applications will be illustrated by a literature review of the dephosphorization process of ferromanganese alloys and by the description of Ti behavior during silico-manganese alloys production. This latter example will show how the thermodynamic models have been used to propose a flotation treatment at low temperature to enhance TiC removal.

Jan 1, 2004

By A. P. I. Popoola, T. J. Olaniyi, A. A. Adeleke

"A laboratory froth flotation experiment was conducted on a low-grade carbonatite copper ore sample obtained from Phalaborwa in the Limpopo province of South Africa. The sample was a homogenous hydrocyclone overflow which serves as the feed to the flotation cells at Palabora Mining Company (PMC). The sample has an average copper assay of 0.59% with predominant copper-bearing minerals being chalcopyrite, bornite and cubanite. The carbonatite nature of the ore comes from the high content of calcium (28.85%) and magnesium (6.84%) minerals. Collectors used were sodium diethyl dithiocarbamate and potassium ethyl xanthate alongside Senfroth 38 supplied by Senmin. The results showed that at 200 g/t mixture of collectors (50:50), an optimum grade of 8.03% Cu in the rougher flotation concentrate was achieved at 74% recovery, while during the second flotation, 24.65% Cu was obtained at 74.4% recovery using a Senfroth 38 dosage of 6 L/t with 100 g/t mixed (50:50) collectors. The particle size and pH value of the pulp played a significant role in that the mixed collectors performed efficiently at pH above 8.3 and at room temperature while particle sizes greater than 53 µm were well concentrated when compared with those of less than 53 µm. INTRODUCTION The need for copper ore concentration research is on the rise as a result of the depletion of deposits and the advent of low-grade copper ores. Although most copper ore deposits have other valuable minerals that support their economic extraction, the increase in technological innovations as regards copper usage and applications has increased the demand for copper. Several factors influence concentration results in a froth flotation column, of which the reagent used is most influential."

Jan 1, 2015

By J. J. Geldenhuys

A colloquium on 'Developments in the Mechanization of Mining Operations' was held in, conjunction with the 1984 Electra Mining Exhibition, at the Milpark Holiday Inn in Johannesburg on 19th September, 1984. An attendance of close on 200 delegates was testimony to the popularity of the subject. The delegates included a number of visitors from abroad, including senior members of the management of foreign companies and a member of the Council of the Institution of Mining and Metallurgy, United Kingdom. Both the local and foreign press was also represented.

Jan 1, 1985

By R. Zivojinovic, S. Vujic

The structural age of the capital mining machinery, representing a part of the system of the Electric Power Industry of Serbia, has been dictated by the initiation and development of open pit coal mines. For example, the oldest bucket wheel excavators were installed some thirty-four years ago, and the average life of the relevant machinery exceeds twenty-two years. Operation of both capital equipment and machinery has direct effects on economic and business activities of open pit mines, and consequently forced us to make a decision and study thoroughly the problem of establishing the optimum exploitation life of capital mining equipment at the open pit coal mines of the Electric Power Industry of Serbia. The aim of this paper is to define and discuss the relative problems as well as to find out the possible solutions and establish the methodology for estimating the optimum exploitation life of machinery. The study was successfully carried out by a team of scientists engaged from and coordinated by the Department of Computer Science of the Faculty of Mining and Geology, University of Belgrade. This paper presents the key observations covering the subject problem. Keywords: Mining, Opencast exploitation, Coal, Optimization, Exploitation life, Capital machinery, Electric power industry, Dynamic programming.

Jan 1, 2003

By K. -H. Lux, Z. Hou

ABSTRACT: It is well known in underground mining and waste disposal that the development of excavation damaged zones (EDZ), and thus, hydraulic pathways, is closely related to the excess in the corresponding damage boundary (= long-term strength) of the rock mass and the resulting damage. By integrating short-term and long-term strength, dilatancy, damage and healing into the newly extended Hou/Lux constitutive model for rock salt, it is possible to treat the tertiary creep, to identify the EDZ around underground facilities and to predict the time-dependent development of the EDZ in rock salt. Under in-situ conditions, the EDZ of a 37-year-old drift at the Sondershausen salt mine and the EDZ around a drift dam in rock salt are numerically examined. The numerical analysis gives satisfactory results. RÉSUMÉ: Dans les exploitations minières et le stockage souterrain des déchets, le développement des zones endommagées et fracturées (EDZ – excavation damaged zone), créant des chemins préférentiels pour écoulement, est étroitement lié au contexte géotechnique et à la méthode d’excavation. En intégrant la résistance court et long terme, la dilatance, l’endommagement et le colmatage, le nouveau modèle rhéologique Hou/Lux pour le sel gemme est capable de traiter le fluage tertiaire, d’évaluer l’extension de l’EDZ et de prédire l’évolution de EDZ dans temps autour des ouvrages creusés dans le sel gemme. L’EDZ d’une galerie datée de 37 ans dans la mine de sel de Sondershausen et les EDZ autour de barrage des galeries dans un sel gemme ont été modélisées. Les résultats numériques fournissent des résultats satisfaisants. ZUSAMENFASSUNG: Bekanntlich ist die Entstehung von Auflockerungszonen und damit hydraulischen Wegsamkeiten in der unmittelbaren Umgebung um bergmännische Hohlräume mit der Überschreitung der entsprechenden Schädigungsgrenze eng verbunden. Unter Berücksichtigung der Bruchfestigkeit, Schädigungsgrenze, Dilatanz, Schädigung und Verheilung kann das Stoffmodell Hou/Lux das Verhalten des tertiären Kriechens beschreiben, die Auflockerungszone im Salzgebirge ermitteln und ihre zeitabhängige Ausdehnung vorausberechnen. Mit diesem Stoffmodell werden die Auflockerungszonen einer 37jährigen Strecke in der Salzgrube Sondershausen und die Auflockerungszonen um ein exemplarisches Abdichtungsbauwerk im Salzgebirge numerisch untersucht. Dabei werden zufriedenstellende Berechnungsergebnisse erzielt.

Jan 1, 2003

By I. R. Firth, D. L. Taylor

Metal mining operations, in particular gold mining operations, use intensive ore control procedures in order to manage the extraction of ore zones from benches containing both ore and waste material. Typical grade control procedures rely on blast hole samples to indicate ore grade. Statistical techniques and geological controls are then used to create two-dimensional polygons, which indicate zones of material designated as ore. These ore-polygons are calculated using pre-blast material locations and are generally not corrected for rock movement caused by blasting. This lack of correction appears to exacerbate the material mischaracterization problem of sending ore to the waste dump and/or waste to the mill. One Nevada gold mining company has estimated that this could be a $10 million per year problem for their operations. Using a simplified vector field algorithm, a method of taking point movement data and interpolating post-blast positions for all nodes in a polygon has been developed. Currently working in 2-dimentions (X-Y), this algorithm utilizes the movement vectors calculated from pre-and post-blast positions of targets placed in a blast, to generate a spatial transformation function for any point on the bench. This transformation is then applied to the nodes of the ore-polygons to produce modified dig lines ore polygons reflecting distortion and movement resulting from the blast. The method as implemented uses common mine planning routines and is performed using the Surpac software suite. The method may be adapted to use any pre-and post-blast point movement data available, and most mine planning suites include the simple interpolation algorithms used. Keywords: Blast movement; Ore control; Open pit blasting; Grade control

Jan 1, 2003

By M. G. Wimberger

The Merensky Reef zone, as developed on Impala Platinum?s Rustenburg Operations, displays a gradational mineralized zone, with grades decreasing from the Merensky Pegmatoid Unit into the footwall and hanging wall. A system of identifying a manageable method of defining the mining cut is introduced, termed the grade profile attenuation cut-off grade. Although horizontal grade selectivity is not applied in the mining of the Merensky Reef zone, low extraction of the orebody, due to manageable and non-manageable factors, can contribute to a reduction in revenue, even losses, due to fixed cost contributions in the mining and beneficiation of the ore. A model is proposed that integrates all variables affecting the revenue of the mining operation, including the grade profile attenuation cut-off grade, the extraction factors, commodity prices and exchange rates, utilizing numerical simulation techniques in a PC-based environment. A breakeven extraction factor for a specific cut-off grade is delivered for a range of market conditions. The breakeven extraction factor is a useful guide when designing mining layouts in structurally complex and low metal content areas. Incorporating distribution functions for individual commodity prices and exchange rates into the model provides mineral resource managers with a risk profile for individual mining areas. Shaft areas have varying grade profiles and each area should have individual models run, to prevent generalizations being made about acceptable risk levels on mining areas.

Jan 1, 2004

[Ferro Alloys Producers Association The South Africa Institute of Mining and Metallurgy www.saimm.co.za Mintek www.mintek.co.za Eskom www.eskom.co.za ]

Jan 1, 2004

By S. Erçayhan, B. Derin, O. Yücel

In the present study, the production of low carbon ferrochromium (LC-FeCr) from chromite concentrates containing 55.09% Cr2O3 and 13.06% Fe via metallothermic process was investigated. For this aim, in the experiments, the aluminothermic reduction method was applied in an open crucible. 10% CrO3 + 10% NaClO3, 15% CrO3 + 5% NaClO3 and 20% CrO3 by weight of concentrate were added to the charge, respectively and the charge was reduced with aluminium. The experiments were done with the additions of 90, 100, 110, 120 and 130% of stoichiometric requirement of aluminium. The highest Cr content in alloys was found as 71.7% at 120% of stoichiometric Al whereas the highest Cr recovery in alloys was found as 71.8% at 130% of stoichiometric Al when the both charge contained 15% CrO3 + 5% NaClO3 by weight of chromite concentrate.

Jan 1, 2004

Bateman Engineering managed the establishment of a second diamond treatment plant at the Letseng Mine in the Mokhotlong District of northern Lesotho, about 100 km from the town of Buthe Buthe. Letseng Diamonds Proprietary Limited, is owned 70 % by Gem Diamonds and 30 % by the Government of the Kingdom of Lesotho. The second plant, which commenced construction in late 2006, doubled Letseng Mines' hard rock processing capacity from 2.6 million t/yr to 5.2 million t/yr, making it the worlds' seventh largest diamond mine by throughput. Bateman Engineering provided the engineering design, procurement and construction management of the new plant.

Jan 1, 2010

By G. C. Thompson

'Increased underground extraction of coal' was the theme selected for the 1981 mining vacation school, which was held at the University of the Witwatersrand in January and February. The response of the industry to the invitation to register was so good that three separate schools of one week each were arranged between 26th January and 13th February. In terms of the total number of delegates, some 225 actually attending, the school can be described as the most successful ever organized by the Institute.

Jan 1, 1981

By F. C. Harris, S. J. Gaab, J. Sattarvand, S. Duzgun

Underground mines are inherently dangerous due to potential hazards such as fires, explosions, and caving of rock. Although these events are rare, once they occur a speedy and safe egress of mineworkers is critical to survival. Static evacuation systems use exit signs or directional lines but can get obstructed or be hardly visible in smoky or dusty conditions. This paper presents the investigation of the effectiveness of a smart evacuation technology in underground mining, where a real-time guidance system leads individuals on an optimised path to the egress while avoiding danger zones, compared to conventional practices. Participants simulated an evacuation from a virtual reality mine, using the conventional system and the smart evacuation system with real-time guidance. The highest reduction in evacuation time using the smart method amounted to nearly 40% on average. Moreover, 83% of participants preferred the smart guidance system, and agreed that it could enhance safety.

Sep 1, 2021

By T. Saito, S. Murata

An original concept of JRC-diagram that can evaluate JRC and its size-effect by using a fractal model was proposed. In order to confirm the applicability of the JRC-diagram, first, JRC of the tensile fracture surfaces of a granite and a sandstone were evaluated by both the JRC-diagram and Barton's JRC-profiles, and then, it was compared with the JRC inversely calculated from the peak shear strength that is obtained from the shear test for each fracture using Barton's empirical equation. As a result, JRC evaluated by the JRC-profiles was much smaller than the inversely calculated JRC. On the other hand, it became clear that JRC evaluated by the JRC-diagram is almost the same with the inversely calculated JRC, if the size of interlocking is evaluated correctly. Therefore, for the JRC evaluation, it is thought that the JRC-diagram is more applicable than the JRC-profiles. Als ein neues Verfahren zur Bewertung des Rauheitsindexes JRC für die Bruchfläche von Felsenschichten anhand eines fraktalen Modells, wobei auch der Maßeffekt berücksichtigt wird, wird ein JRC-Diagramm vorgeschlagen. Um die Angemessenheit der Bewertung vom JRC mit diesem JRC-Diagramm festzustellen, wurden die JRC-Werte an einer Bruchfläche zwischen Granit und Sandstein sowohl mit dem JRC-Diagramm als auch mit dem herkömmlichen JRC-Profilverfahren bewertet. Anschließend wurden die durch die beiden Verfahren ermittelten Werten mit den JRC-Werten verglichen, die von den Schertestergebnissen mit Hilfe von Bartonschen Erfahrungsformel zurückgerechnet werden können. Daraus ergab sich, daß das JRC-Profilverfahren ziemlich kleinere JRC-Werte gibt als bei der Zurückrechnung, während die JRC-Werte durch das JRC-Diagramm unter entsprechender Bewertung des Ineinandergreifungsmaßes an der Bruchfläche beinahe gleich sind wie die zurückgerechneten Werte. Diese Tatsache weist darauf hin, daß das JRC-Diagramm eine bessere JRC-Bewertungsmethode als das JRC-Profilverfahren darstellt. Nous avons proposé le diagramme JRC, nouvelle méthode d'évaluer JRC qui est un indice de rugosité superficielle d'une fracture de roche à l'aide du modèle de fracturation, compte tenu de son effet d'échelle. Pour vérifier la validité de JRC évalué au moyen de ce diagramme, nous avons évalué JRC d'une fracture de roche, granite et grès, par le diagramme JRC et le profil JRC, méthode conventionnelle, et les résultats ainsi obtenus ont été comparés avec la valeur de JRC calculée en sens inverse à l'aide de la formule empirique Barton sur la base des résultats de l'essai de cisaillement des fractures. Il en résulte que la valeur de JRC obtenue par le profil JRC était assez faible en comparaison avec la valeur calculée en sens inverse alors que celle de JRC obtenue par le diagramme JRC correspondait approximativement à la valeur calculée en sens inverse à condition d'évaluer l'échelle d'endentement d'une fracture. Par conséquent, nous considérons que le diagramme JRC est une meilleure méthode d'évaluation de JRC par rapport au profil JRC.

Jan 1, 2003

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Experiments were conducted to study the influence of temperature, particle size and ore/coke ratio on the kinetics of reduction. The rate of reduction increased with temperature. The reduction of iron was completed at shorter time intervals at temperature above 1000ºC. Usually the reduction of chromium commenced after the reduction of iron was almost complete. Reduction was controlled by diffusion at low temperatures and by chemical reaction at higher temperatures. The nature of the reducing agent had a very significant influence on the rate of reduction. The study showed that chromium was converted into the carbide during reduction. Increasing the size of the reducing agent increased the rate of reduction initially. After a critical size, the rate of reduction decreased. However, increasing the size of the ore particle decreased the rate of reduction, initially. Beyond a critical size, it increased. An optimum particle size of the chromite ore and that of coke must be chosen, particularly in the production of agglomerates to achieve maximum degree of reduction.

Jan 1, 2007

By X. B. Zhao, J. G. Cai

The purpose of this paper is to incorporate the dynamic BB model of rock fracture normal behaviour into Universal Distinct Element Code (UDEC), and to conduct UDEC modelling to predict stress wave propagation across rock fractures. With the incorporation of new dynamic model of fractures, the UDEC is improved in the capability of modelling wave propagation across fractures. In this study, the case of normally incident P-wave transmission across a fracture is modelled, and the effect of dynamic normal behaviour of fracture is concentrated on. Wave transmission coefficient for wave transmission across the fracture with the dynamic BB model is obtained for various combinations of fracture dynamic parameters, as well as different wave amplitudes and frequencies.

Jan 1, 2003

By Jeffrey C. Hillman

The need to recruit locally produced engineers by the South African Mining Industry led to the Engineering Faculty at the University of the Witwatersrand developing a number of academic bridging initiatives for educationally disadvantaged students. The graduation rate achieved during the initial five years of operation by the most successful of these programmes has been on a par with that of al other students but the performance of subsequent intakes has declined to such an extent that the continuance of this scheme could now be at risk. One reason for this reduction in throughput is that many of the applicants for the increasing number of mining bursaries have been more interested in the bursary than the profession and have either failed or dropped out due to a lack of application and motivation. This will have serious consequences for both Wits and the Industry if it continues and some method of identifying unsuitable or suspect applicants needs to be introduced as a mater of urgency. It is recommended that an introductory course be set up at a working mine that would be run under the auspices of Wits, as a joint venture with industry, and include a level of academic input that would provide both bridging needs and certain first year credits. The final form of this course will require extensive consultation with al parties but needs to be completed before the end of 1996. It is further recommended that the advertising and promotion of mining careers be expanded and much improved.

Jan 1, 1996

By W. A. Gericke, B. Olmstead, I. Mc Dougall, C. F. R. Smith

A finite element model was generated of a Søderberg electrode in a ferromanganese smelter. In this model, the casing and fins were modelled explicitly, and temperature-dependent material properties were included. A two-stage analysis procedure was used, the first part being a coupled thermal-electrical analysis using an applied DC current. As the casing material was non-magnetic, the DC current was deemed sufficiently accurate for this initial analysis. The proximity effect was not considered. Thermal boundary conditions based on assumed temperature distributions in the furnace were applied. Calculated temperatures agreed well with measured values. The joule heat calculated in this step was applied as a load to a coupled thermalstress analysis. The model was applied to a comparative study of alternative materials for the casing and fins. A number of different combinations of materials for the casing and fins were evaluated in a comparative study. The position of the baking zone was used as the criterion for evaluating the potential of each material combination. Based on this analysis, some material combinations were discarded as being entirely unsuitable, whilst the two most suitable combinations will be tested experimentally in the furnace. The stress analysis was performed on the most suitable option. The practical advantage of this analysis was that a number of what-if scenarios could be evaluated and discarded prior to embarking on expensive experimental work, thus limiting the amount of experimental effort required. A mathematical model allows for the comparison of options under controlled conditions, where parameters of interest can be varied individually, with all other parameters remaining the same, a condition which is difficult to achieve in an operating furnace.

Jan 1, 2004

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007