Search Documents

By G. F. Ayakwah

Point load strength (Is50) and slake durability (ID2) indices provide a measure of the strength and durability of rock fragments and are related to the alteration intensity and frictional resistance of the materials. Samples were collected from the rock piles, alteration scars and debris flows at the Questa mine with the purpose of examining relationships between Is50 and ID2, mineralogy, chemistry, weathering, hydrothermal alteration, and other geotechnical parameters. The Is50 from the various rock piles ranges from 0.6-8.2 MPa and the ID2 ranges from 80.9-99.5%. The Is50 and ID2 results indicate that the samples from the debris flows are stronger (average Is50= 4.0 MPa and ID2= 98.4%) than the rock-pile samples and that the alteration scar samples are weaker (average Is50 = 2.8 MPa and ID2 = 89.2%) than the rock-pile samples, but still most of these rocks are strong in terms of their Is50 and ID2. The Is50 decreases as the degree of alteration increases in some rock pile and alteration scar samples, but not in all. However, the majority of the rock fragments within the rock piles still indicate high strength, even after 25-40 years of weathering.

Jan 1, 2009

By Wen L. Chen

The steam coal quality is less stringent than metallurgical coal quality. The steam coal is prepared either by cleaning full size range of raw coal or cleaning coarse coal only, leaving the fine coal raw. The latter scheme is more cost competitive. It is particularly applicable to U.S. eastern soft coal where low ash coal is concentrated in fine sizes. For raw coal size separation, a recently developed Rotating Probability Screen, developed by the British Coal Board, may be advantageously used for easy change of raw coal separating size and to avoid screen deck plugging when handling wet and clayey raw coals.

Jan 1, 1983

By D. G. Kotlyar

Silver is an economically important component of many complex, massive sulfide ores. Current beneficiation for these ores is almost entirely by flotation. Silver recovery often is low, but little is known about the flotation behavior of the silver-bearing minerals. Floatability studies were conducted using silver-bearing tetrahedrite and lead-zinc ore. The effects of xanthate collector concentration, conditioning time, potentiostatic control of the mineral potential, and pH on mineral floatability were evaluated. The floatability of the silver-bearing minerals was shown to depend on collector concentration and mineral potential. The effect of controlling mineral potential during the flotation process is discussed.

Jan 1, 1994

By James R. Boulton

Fire detection using Carbon Monoxide sensors is based on the assumption that a rise in the level of Carbon Monoxide in the atmosphere over a fixed, predetermined ambient level is indicative of a fire. The method is simple, reliable, and effective in those mines where the only source of CO is from undesired combustion. Ambience for this purpose is defined as that level of the gas that is present on a day to day basis whose source is not a fire. In a diesel powered mine the level of CO can and does vary so widely from hour to hour and minute to minute that the selection of a predetermined, fixed level represents a compromise between sensitivity and reliability. The compromise is a best of both and worst of both situations and the computer system often resembles the little boy who cried wolf instead of a state of the art early fire monitoring and detection system. Cyprus Coal personnel have developed method of determining the ambient level of CO in the atmosphere on a real time basis and using that dynamic ambient level to determine whether or not a fire exists in the mine. The method has been given the name of Wave Trend Crossing.

Jan 1, 1991

By T. P. Meloy

The packed column flotation cell is an awesome separation device. Virtually unknown and untested, the packed column flotation cell is one of the ten most important developments in mineral processing of the 21st century. Though experimental and industrial data is limited, it is clear that the packed column flotation cell is two to three orders of magnitude better than the conventional flotation cell and one to one and a half orders of magnitude better than the open column flotation cell. With the modern packing taking up less than one percent of the packed column, column blocking does not occur. For a packed column operating 24 hours a day, 365 days a year, the estimated mean time between failures (MTBF) is one hundred thousand hours or roughly twelve years. With no moving parts, lower maintenance costs, lower power consumption and inherent operating stability, the packed column is a powerful separating machine. Because there is little meaningful data for comparing the packed column to the conventional flotation cell and the open column flotation cell, much of the material presented in this paper are guesstimates. They are disinterested guesstimate made by the authors after extensive theoretical work and reviewing the known facts. In the authors' opinion, no available data contradicts the guesstimate. The authors expect that there may be errors as large as three hundred percent. Even three hundred percent errors will not change the conclusions of this paper. The packed column flotation cell is a formidable separating device. To understand the problems of comparing the three types of flotation cells, consider the fact that the three cells may have different modes of separation. One of the authors, Meloy, believes that in the conventional cell, the primary particle separation takes place in the liquor with secondary separation taking place in the froth, while for open column flotation, all the separation takes place in the froth. However, he believes that in the packed column a large part of the separation may take place on the walls of the packing. If this is true, not only is the method of modeling each type of cell different, but the method of particle selection in the cell is different. This means that one type of cell may be better at differentiating between two different types of particles. There is a growing body of literature on open and packed column flotation. Suggested reading: (Clarke et al; Hucko et al; Li; Smith & Warren; and Yang).

Jan 1, 1994

By R. J. Beckman

This paper traces the history of mica mining in Alabama from 1870-1970. The decline of sheet mica production is noted and emphasis is placed on the more recent activity of scrap mica production and the development of the U. S. Gypsum Co. mica properties in Randolph County, Prospecting for weathered pegmatites of sufficient size to warrant development is a continuing challenge since most deposits are too small and all exhibit varying characteristics as to size, shape, and weathering. Quantity and quality of muscovite mica in the pegmatites is of utmost importance and its recovery during processing of the ore is described.

Jan 1, 1970

By Gerrit V. R. Goodman, Fred N. Kissell

The issue of miner safety in case of an underground mine fire has been extensively examined by both government and industry. These efforts have intensified in recent years following a number of fatal fires at underground coal mines. As a result, there is an increasing interest in the reliability of coal mine escapeways during a mine fire. This paper discusses the use of fault tree analysis for evaluating escapeway reliability. A fault tree is developed using standard logic formulations. It is later evaluated using commercially available software. The computer model uses Boolean reduction to obtain the minimal cut sets and minimal path sets of the tree. A brief analysis is also conducted to determine the occurrence probability of the TOP event. This study shows that fault tree analysis is a viable means of analyzing escapeway reliability. The cut and path sets reveal those event sequences leading to fatalities. Such information is useful in safety training and accident prevention. The probability of the TOP event shows the frequency of occurrence for fatalities in an underground mine fire. The usefulness of this value, however, is limited by the accuracy of the data for the initiating events. For mining events, the data is difficult to estimate precisely.

Jan 1, 1989

By G. Markopoulos

Thracean Gold Mining is a Greek Company specialized in gold exploration and exploitation. It is focused on the development of the advanced Perama Hill gold project, which is currently waiting approval of the environmental terms of reference from the Ministry of Environment. We have designed a mine operation that is completely safe environmentally. The mine design exceeds all the standards environmental safety set by the European Union. We are currently negotiating lasting relationships with the communities which surround the mine by creating sustainable projects within the area that will provide sources of income to the region long after the mine is exhausted.

Jan 1, 2007

The importance of factoring mining dilution into the estimation of ore reserves in an open pit mine is discussed. An example that relates the issue of mining dilution to the size of the smallest volumes that can be mined selectively is given. The relationship between the size of the selective mining units (SMUs) and the variance of their average grade is presented. The concept of variance reduction and its use in factoring mining dilution into geostatistical ore reserve estimation is described. An approach to estimate a variance reduction factor by way of conditional simulation is introduced.

Jan 1, 1998

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986

By Thomas W. Healy, David V. Boger, Yee-Kwong Leong, Lee R. White, Peter J. Scales

The concentration of mineral slurries by conventional thickening devices is discussed. The role of additives on the compression of mineral slurries is also examined. Results for a range of flocculation conditions are presented. The compression of flocculated mineral slurries is found to be highly dependent on the fundamental particle-particle interaction forces and hence, the rheology of the particulate fluid. It is demonstrated that a detailed knowledge of the properties of both the mode of operation of the thickening device and of the solid/liquid interface is required for improvement in the rate and in particular, the extent of dewatering.

Jan 1, 1995

By Howard L. Hartman

Pardon my audacity, but I feel that this is the solution, not just a solution. Further, I will be so bold as to maintain that this is the last-ditch, eleventh-hour chance for the mineral industry to solve its critical technical manpower shortage. I am not being facetious. I am convinced that there is only one solution--just as there is but one real cause of the problem. My conclusion 'is reinforced by countless talks of endless hours with people both in and out of the industry, with employers and employees, and with educators and students. While I claim no originality for the idea and have no pride of authorship, I am concerned that the industry hear and heed in time. It is quite unlikely that the mineral industry and the mineral engineering profession will willingly subscribe to my thesis or gladly buy my proposal. I am convinced, however, that it is the only course of action open to us, and the only course of action which will succeed.

Jan 1, 1967

By F. C. Bond

Nature of Empirical Calculations The size reduction of large tonnages of ore and rock is an operation of great magnitude. It is a necessary and important part of industry. Its development has been motivated by practical need and has followed the path of an industrial art without much help from theoretical science. Knowledge has been accumulated from experience. Trial and error established the methods; then collected data were tabulated and served as the basis for empirical equations that have been continually modi¬fied and amplified as new data became available. These equations now constitute the bulk of our present knowledge of comminution. There is no accepted scientific theory that is basic to comminution. In electrical, mechanical, and civil engineering, as well as in many other industrial activities, such theories exist and are extremely help¬ful, but rock is essentially heterogeneous, and the zones of weakness that control its breakage are thoroughly diversified. No theory has yet been discovered which can account for the variability of rock, although many attempts have been made. Empirical equations tell nothing of the why of a phenomenon, but if they are properly derived they can tell much about the how. They always represent only an approximation of behavior but never a law. In a proper empirical equation a symbol is assigned for each of the variable quantities that obviously affect the relationship. In a grinding mill these include mill diameter, mill speed, and feed rate among them. In setting up and revising an empirical equation the cardinal princi¬ple in establishing and modifying it is this: any change must be strictly ascribed to the variable which caused it. A useful empirical equation is rendered useless when a change in any convenient coefficient or exponent is made to make it fit a particular set of data, without certainty that the altered coefficient or exponent is the responsible variable in the new data. Such indiscriminate revisions have brought the use of empirical equations into some disrepute. When existing equations are changed to accommodate new data it is a good rule to make a change which gives results intermediate between the new and the old. A halfway point is usually a good choice.

Jan 1, 1985

By Randhir S. Sehgal

After some decades of lying low and being treated as a second rate fuel, coal is back in the news. Production is rising. Predictions are for an ever expanding use, and they differ only in their rates of increase. Even the FBI is involved in trying to stop fraudulent sales of non-existent coal lands and leases to the innocent. In short, we have a nearly chaotic boom on our hands. Obviously our energy production base is in the process of undergoing a major shift, and the process will present many problems. However, there is little doubt that the industry has the basic strength and organization to be able to deal with the new issues that will arise as a result of these shifts in production and use of coal. After all, it does produce nearly 800 M tpy now, and coal is the single biggest fuel for generation of electricity. This role of coal is illustrated in the table below, which shows the coal equivalent quantities of various fuels used in the production of electricity.

Jan 1, 1980

By Wang Xifu, Zhang Daxian, Zhang Youdi

In mine haulage system, the surge bunker or stockpile installed between two facilities can raise the system production capacity. The arrangement of surge bunker has great relation with the capability development of the whole haulage system and the economic benifit. In the haulage system, surge bunker plays a role of surge capacity, accident capacity and technology capacity. In this paper, the variation of the material in surge bunker is analysed while the mine haulage system is working, the calculation method of the whole output is raised. With the goal of the maximum system output, the method of deciding the rational size of surge bunker is put out. In case study, the system output in Huolinhe surface mine is calculated, thus the rational size of surge bunker in huaulage system is decided.

Jan 1, 1996

By R. R. Beebe

When an economic mineral deposit is first discovered, it is almost immediately defined in terms of tonnage and grade. As exploration and assessment continue, the initial definition is ordinarily qualified by such terms as "proven," "probable" and so on. Even at this stage, the fundamental philosophies of the discoverers may manifest themselves in conservative or optimistic views of the deposit's potential. It is unusual, however, for the philosophies to be expressed in terms of metallurgical performance criteria at such an early stage unless the ore is very unusual in its chemistry or mineralogy. Even before drilling is completed, the first mining plans appear, with or without the benefit of metallurgical test data. This is the point at which management philosophies can have some of their greatest impacts. In ideal cases, where large, uniform ore bodies can be developed and mined according to assay cutoffs, the conventional philosophy of maximizing tonnage while minimizing cost can be followed without much metallurgical difficulty. Unfortunately, such cases are rather uncommon. Even large, low-grade

Jan 1, 1991

By Jurgen H. L. Stuve, Rick E. M. Widelski

Any one who has been involved with the mining or the treatment of gold-bearing ores will agree that at the end of the total process, the quantity of gold recovered is never as much as was expected. These short falls are usually explained away by claiming that:- the original evaluation of the ore being mined was inaccurate the plant treatment process is not at its optimum theft is taking place excessive dilution occurs during mining The truth of the matter is that the gold is being "lost". During all the stages of its production, starting from the mining, right through to the smelting process, a certain amount of gold is not recovered. When a newly found gold deposit is being evaluated and the drilling data being analysed, cautionary factors are applied so that the grade is not over-stated. Once the decision has been taken to start mining and development is in progress, the exposed ore is sampled. When Again, when this data is being analysed more safety factors are used to ensure that when a piece of ground is given a block-value, the gold content is not over estimated. mining actually takes place and the ore transported to the plant for treatment, the metallurgical department also introduces certain safety factors when predicting how much gold will be recovered. This shows that the quantity of gold that one expects to finally recover is already a conservative figure. The actual quantity recovered invariably falls short of this figure, in fact, South African gold mines are satisfied when achieving a Mine Call Factor (MCF) of 85%. In the last few years a great deal of work has been carried out to investigate how this unaccounted for gold is lost and what steps can be taken to remedy the situation. Previously mined areas were re-swept using the traditional hand brush method; experiments were carried out with water jets sometimes in conjunction with compressed air and even small portable vacuum cleaners were tried. None of these methods were totally successful in recovering the left over gold but the use of vacuum systems showed the most potential. the In South Africa this has resulted in introduction of high-powered vacuum systems on the gold mines to suck-up this lost gold. These were initially introduced in the mining areas, particularly old areas, to recover any left over ore. The results proved extremely profitable, So much SO that presently, well over 120 suction systems are doing this type of work. This success encouraged plant operators to look at areas of potential loss in the plant itself. This has resulted in an increasing number of machines being supplied to gold plants mainly for clean-up applications with the bonus that the material sucked up invariably contains gold.

Jan 1, 1993

By Edward D. Elkins

CalMat Co. is one of the largest producers of construction aggregates in the United States. The CalMat Reliance plant is located in Irwindale, California, and is situated on an alluvial fan formed by the San Gabriel River. The fan deposits are of Quaternary age and were derived from granitic and metamorphic bedrock exposed in the San Gabriel Mountains to the north. The sediments are poorly sorted and range in size from large boulders to clay size particles. The coarse material is hard and durable and consists of quartz diorite, granodiorite, granitic gneiss, schist and minor amounts of volcanic rock. The matrix is comprised of silty sand with varying amounts of clay. Thin silt and clay lenses occur sporadically throughout the deposit. The clay content of the matrix and the degree of weathering of the coarse material increases with depth. Based on seismic data, the alluvial fan varies from 200 to 400 feet thick and overlies crystalline bedrock. The Reliance plant was constructed in 1971 and 1972. It has a nominal capacity of 1200 to 1400 tons per hour, and typically produces more than three million tons of aggregate products per year. Alluvial fan sediments are mined from a gravel pit situated adjacent to the plant. The material is fed through a mobile, 48- by 60-inch, in-pit jaw crusher, then transported by conveyor to the main plant to be processed. The plant is modern and highly efficient. It has a typical wet and dry circuit and is capable of producing a wide range of aggregate products. To extend the life of the plant, a 9,000 foot conveyor system is being constructed to connect it to a granite quarry operated by Azusa Rock Inc. The quarry is located north of Irwindale, and is 50 percent owned by CalMat Co. The conveyor will be used to export crushed rock from the quarry to Reliance. The existing plant will be modified to process the crushed rock.

Jan 1, 1995

By A. Vaillant

Classifiers that are used to separate granular materials into a coarse and a fine stream, are considered. Fundamental Equations are presented which apply to all, such Classifiers and all feed size distributions. The practical, real Classifier is compared quantitatively with the perfect. Classifier. A Formula is introduced for the Real Classifier Selectivity, that defines what portion of each particle size is sent to the coarse outlet duct. This selectivity function is characterized by three Parameters, one of which (b) is a numerical measure of the sharpness of classification. A new dimensionless variable (J) appears in Equations and Graphs for recirculating load, product size distribution and specific surface in the classified product. This variable combines the effects of sharpness of separation, Classifier setting and fineness of a Rosin-Rammler Type feed to the Classifier. Classifier efficiency is defined, based on Specific Surface.

Jan 1, 1967

By Atsushi Sainoki

Induced seismicity is deeply related to various engineering projects entailing anthropogenic in-situ stress change in deep underground. Hence, there is a persistent demand for estimating and mitigating the risk. Significant efforts have been made in simulating induced seismicity with a variety of numerical simulation techniques; however, there are still discrepancies between characteristics of induced seismicity numerically simulated and observed in the field. One of such discrepancies is the simulation of triggered seismicity defined as seismic events caused by an infinitesimal amount of anthropogenic stress change, which is frequently observed in geological structures. The present study aims to develop a methodology to simulate triggered seismicity whilst reproducing a complex stress state in a fault zone. For the purpose, a discrete fracture network within a fault damage zone is first generated. Then, an equivalent continuum model, in which each zone has a different anisotropic compliance tensor, is constructed by employing the crack tensor theory. A fault core is simulated at the center of the model with interface elements. Using the equivalent continuum model, an initial stress condition is simulated with the boundary traction method, which results in a very complex stress state with stress anomalies due to the stiffness anisotropy and heterogeneity. Subsequently, the effective normal stress on the fault plane is decreased in a stepwise manner to induce slip. The result demonstrated that many seismic events are induced on the fault plane with a slight decrease in the confining stress, thus being regarded as triggered seismic event. Further analysis on this seismic activity shows that the magnitude of triggered seismic events is inconsistent with the amount of shear stress drop, implying that a relatively small triggered seismic event could produce a large stress drop, generating locally intense ground motions and thus inducing severe damage to the nearby rock mass.

Apr 26, 2022