Search Documents

By Malcolm J. McPherson

Within the world of mining health and safety, increasing attention is again being given to underground fires and explosions. This paper reviews the effects of open fires in mine entries on the ventilation system, and outlines current methodologies of attempting to control such a fire. The particular hazards of a fuel-rich fire are discussed. There appear to have been no really significant advances made in methods of extinguishing mine entry fires in the last several decades. The final section of the paper introduces research that is investigating the simultaneous production of an inerting, cooling and quenching atmosphere by means of a dense water fog.

Jan 1, 1993

By Bradford F. Townsend, Gary Peach, Roger Rothenburger

From the experience of the authors on recent large infrastructure Design-Build projects this paper reviews major lessons for Contractors and Owners in the delivery of large Design-Build infrastructure projects and some major pitfalls and warnings to both Owners and Contractors. The paper is written from both the Design and Construction perspective. A case history is presented that details the approach employed to ensure a quality project consistent from the initial design phase through construction and outlines the strategy used to guide the Design-Build process to an acceptable completion. Suggestions are made for Contractors and Owners for handling the Design and the Construction elements of Design-Build contracts.

Jan 1, 2003

By N. P. Reddy, Y. J. Wang

Stall or aerodynamic stall of axial flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1993

By St. E. Deák

Mining activities involve excavation from underground to the surface of large quantities of ore (e.g. uranium and its disintegration products) (Dumitrescu, 2002, 2007). Material with limited content of uranium, deemed as sterile or low-radioactive is mainly stored on the surface. These wastes modify the configuration of the disposal areas and affect the quality of the environment and the landscape. This paper presents both analytical and numerical models related to stability assessment of uranium mining waste dumps. It is focused on the calibration procedure of the numerical models, in order to minimize risk error during stability prediction and avoid long term environment pollution.

Jan 1, 2008

By G. Pierson

Explanations for commodity price levels (or movements) commonly focus on the fundamentals of supply and demand otherwise they are simply assigned to speculative activity. Comparisons of metal-price histories to monetary and other economic data support the argument that the supply of and demand for money are no less important in the determination of price than are the supply and demand of the commodity itself. That these relationships should exist is evident in the price identity and they are consistent with monetary theory. The patterns developed have limited usefulness as predictors, but their recognition is essential for the construction of price scenarios for planning purposes.

Jan 1, 1998

By R. K. Rajamani, R. Verma

In ball milling the rates of breakage vary primarily with the size distribution of powder in the mill. Using an approximate solution to the batch-grinding equation, the acceleration and deceleration of breakage rates of all individual size classes are determined when the grinding environment is varied. Experimental results with limestone and copper ore show time-dependent breakage rates under both dry and wet grinding conditions. The effect of grinding additives on breakage rates is also studied. In general, breakage rates increase for coarse sizes and decrease for fine sizes with an increase in the fines present in the mill. Such variations have strong implications in closed-circuit grinding.

Jan 1, 1992

By Shoung Ouyang, Pinnaduwa H. S. W. Kulatilake

Available literature on the topic is reviewed. Methods are suggested to improve the presently available techniques to perform probabilistic modeling of shear strength parameters for rock discontinuities. The Mohr-Coulomb model and a power law model are used as strength criteria to model shear strength of rock discontinuities. Use of various regression techniques for point estimation of shear strength parameters from direct shear data are discussed. Goodness-of-fit tests for bivariate beta and bivariate normal distributions are developed, and the applicability of them to represent the distribution of shear strength parameters is tested through examples. Both distributions seem to have potential to represent the statistical distribution of strength parameters.

Jan 1, 1986

By M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology for estimating gold recoveries in gravity-separation circuits is presented. The methodology makes use of a population-balance model. The model represents gold liberation, breakage and classification behavior and applies preconcentration and recovery performance curves to gravity-recoverable gold. The derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and from a projected application. The methodology makes it possible to estimate the performance of a gravity circuit having a large gold circulating load and a relatively-low unit recovery (e.g., a jig) or having a high recovery on a bleed of the circulating load (e.g., a Knelson Concentrator).

Jan 1, 1996

By Thomas H. Hibner, Daniel Tempelis, John E. Shamma

Environmental protection of nearby resources is an issue that can not be ignored in tunnel construction. The Inland Feeder Arrowhead Tunnels Project is no exception. With keen interest from various stakeholders, Metropolitan developed a Groundwater Monitoring and Mitigation Plan. This plan provides for monitoring and management of selected water resource features within the San Bernardino National Forest along the proposed tunnel alignment. The plan specifically provides for monitoring of streams, springs, seeps, and piezometers for water temperature, pH, specific conductance, and chemical analyses, as well as flow or groundwater elevation. Metropolitan uses the data to evaluate for and manage potential impacts from groundwater ingress during construction of the Arrowhead Tunnels.

Jan 1, 2003

By Stephen Leslie

A multimedia tutorial illustrating the geology and mineral resources of Gulf Coast salt domes has been developed as a pilot project for a course on Texas geology and resources at the University of Texas at Austin. The principal objective of the tutorial is to educate students with limited background in geological sciences about a major local geologic feature and its geologic and economic significance. The content of the tutorial represents materials generally covered in 4 hours of lecture and laboratory instruction. These materials are presented using a flattened hierarchy of topics, each accessible from a central menu, including salt-dome history, salt tectonics, anhydrite and calcite cap rocks, mineral resources, and geophysical character. Information concerning salt-dome geology is communicated using interactive software; sound and animation are used throughout to reinforce key concepts. Visual aspects include field views, hand specimens, and photomicrographs that were digitized from slides. Illustrations were created using a graphics program or scanned from available archives. Each visual element has an accompanying explanation, which in many cases is linked to other parts of the tutorial. Navigation is accomplished using hyper-links or a set of unobtrusive buttons. The program includes a glossary of the major minerals associated with salt domes available as a pull-down menu and digitized video footage of the Gulf of Mexico sea floor to illustrate the active environment of the formation of the salt-dome cap rock. In addition, a group of interactive questions is presented to assess the level of mastery. Technical aspects were accomplished using a Power Macintosh ? 7100AV and a variety of commercial software. Actual linking of information was done with Authorware? 3.0 Educational, an icon-based, multimedia authoring program. Graphic illustration was done with Adobe Illustrator ?; image processing was accomplished using Adobe Photoshop?; video was cap¬tured, edited, and compressed using Adobe Premiere ?. The interactive nature of the project was designed with regard to future means of dissemination, especially on the World Wide Web. This tutorial serves as a template to build additional modules covering the entire course. A modular approach to the coding of the project and extensive self-documentation should ensure the viabil¬ity of the project by allowing other workers with moder¬ate computer skills to complete other lessons within the curriculum framework.

Jan 1, 1999

By W lethlean, Laurie Smith

When coarse gold is present in an ore, there are advantages in physically recovering this gold in the grinding section of the ore processing plant. This reduces the risk of the coarse gold being locked up in the grinding section equipment, reduces the quantity of activated carbon to be eluted and reduces the risk of gold passing out of the cyanide leaching circuit only partially dissolved. The free gold may be recovered by various mechanical means utilising the significant difference between the specific gravity of the gold and waste minerals. Frequently, sulphide minerals and ball mill attrition steel in the form of fines and chips are present in the ground ore and behave in a similar manner to the gold in the concentrating process. These materials must be removed to produce a concentrate suitable for direct smelting and several stages of cleaning, sometimes utilising different physical principles, may be required. The removal of these materials invariably results in a loss of gold from the final concentrate. The rejected materials containing significant quantities of gold are returned to the grinding section, consequently the opportunity for a high and early recovery has been lost. The quantity of gold returned to the grinding section will vary according to the number and type of cleaning stages and the physical characteristics of the materials and the gold but surveys of the gravity concentration processes suggest that it may be as high as 50%. To maximise the recovery of gold from the primary gravity concentrate, some operations batch cyanide leach this concentrate with or without additional reagents. The method of agitation and solution recovery vary. The most common method of agitation is by a high-speed propeller mixer and the least expensive but time-consuming method of solution recovery is by decantation after settling and by repeated decant washing. The pregnant gold solution is either introduced into the main ore leaching circuit or the gold is recovered by direct electrowinning. After commissioning in 1994, Union Reefs Gold Mine (URGM) experienced below expected recovery of gold from the gravity concentrate generated from the Knelson Concentrators. It was shown that the recovery into the Knelson Concentrate was high but that the subsequent mechanical concentrating techniques of tabling and magnetic separation resulted in significant gold being returned to the grinding circuit.

Jan 1, 2000

By G. Pierson

Explanations of commodity price levels, or movements, commonly focus on the supply and demand fundamentals of the particular commodity, or else are assigned to speculative activity. Comparisons of metal price histories with monetary and other economic data support the argument that the supply of and demand for money are no less important in price determination than are the supply and demand of the commodity itself. That these relationships should exist is evident in the price identity and are consistent with monetary theory. The patterns developed have limited usefulness as predictors, but their recognition is essential for the construction of price scenarios for planning purposes.

Jan 1, 1996

By Howard M. Graff

The Inland Steel Company operates five underground iron mines in the Lake Superior District. The two largest of these, from the standpoint of productive capacity, are the Sherwood Mine in Iron River and the Bristol Mine in Crystal Falls, both on the Menominee Range of Michigan. It is at these two mines that we have had our principal experience with belt conveyor installations underground, .At the Sherwood Mine, which has an annual capacity of about 450,000 tons, the first conveyor belt installationwas made in 1947 when conveyors were installed in the main haulage drifts on the 1200 ft, level, It was estimated at that time that approximately 5,000,000 tons would be mined from the stopes above the 1200 ft, level and. that if all this material could be moved to the shaft by belt conveyor, the entire cost of operation, including maintenance and the amortization of the equipment, would be about $,05 per ton, which was slightly more than half of what the cost would have been by conventional tramming methods employing locomotives and cars. Now, ten years later, the 1200 ft, level is almost completely mined out and we have actually removed. 5,200,000 tons and. the average cost of transporting this material to the shaft by belt conveyor has been $.095 per ton. Since there has been a substantial increase in hourly rate of pay and also in the cost of materials since 1947, we feel that the anticipated savings were very nearly realized., The 1200 ft, level installation at the Sherwood consisted of two 36" trunk line conveyors 815 feet long and 380 feet long, respectively, deliverying ore to the shaft. These in turn were fed. by three lateral 36" conveyors which paralleled the sides of the orebody, These gathering conveyors passed under draw points to which ore was brought from the stopes by mea S of scrapers or shaker conveyors, Shaker conveyors were used for a number of years in conjunction with the conveyor belt system of haulage but it was finally concluded that with this particular type of ore, the maintenance on shaker conveyors was excessive. Therefore, more recently, we have gone back to scrapers for the shorter distances and. are using belt conveyors in the scraper drifts for the longer distances. After this belt system had been in operation for about three years, it had proved to be so successful that it was decided to proceed with the same system or. a new level to be opened up 200 feet below. Instead of sinking the shaft and driving a horizontal drift to the orebody on the 1400 ft, level, an inclined conveyor drift was started near the shaft at the 1200 ft. level and driven downwards toward, the orebody at a slope of 15 degrees. The conveyor installed in this inclined drift is 36" wide, 990 feet long, is powered. by a 100 hp motor, and is capable of delivering 300 tons per hour to the 1200 ft, level shaft pocket. It is fed by lateral horizontal conveyors on the 1300 ft? 1400 ft., and 1425 ft, sub levels. Wien the inclined drift was started, the rock was scraped from the breast directly to the rock pocket at the shaft. As the distance increased., double scraping was employed, until the advance had reached 350 feet, At this point a portion of the final conveyor was installed, with a scraper slide near the breast, T e drift was then advanced be scraping on to the conveyor until a sufficient distance had been driven to permit the installation of an additional 200 feet of conveyor. This proved to be a very efficient and economical means of moving the development rock to the shaft and obviated the need of using cars or an inclined skip way, At the present time 85 percet of tie entire mine output is being mined below the 1200 ft, level and is delivered to the shaft via the inclined conveyor. The system appears to be working as well and as economically as did the conveyor systemonthe 1200 ft, level.

Jan 1, 1958

By A. O. Drysdale

From a mining point of view the Portland Cement Industry falls logically into the Industrial Minerals Division. Portland Cement manufacture requires four principal materials, lime, silica, alumina and iron. The usual source of lime is limestone. Silica sources include clay, shale, quartz, sandstone and sand. Alumina is usually provided by selecting a silica source with a suitable alumina content such as clay and shale. "Cement Rock" is occasionally found in which all four ingredients are found in natural combination or sufficiently close that only minor adjustments are required. In the absence of iron oxides a white cement can be produced. All raw materials used in Canada contain some iron and in most plants further minor quantities of iron are added to promote fluxing, hence the typical grey colour of Portland cement. The modern period in cement manufacturing started in 1824 when Joseph Aspdin of England patented a process for the manufacture of a modified hydraulic cement which he called "Portland Cement". Hydraulic cements are cements that harden under water. Although natural cements, made by calcining and grinding natural argillaceous limestone were produced in Canada as early as the 1830's, Portland cement was not produced in Canada until 1890, about 18 years after it was first made in the United States.

Jan 1, 1964

By Emil Szaks

[A great number of papers have been presented at various Engineering Society meetings on the Unit Train subject. Moat are descriptions of facilities that have been constructed or are abort to be built. Many describe the facility as being the World's fastest, newest, largest, incorporating the latest technology and so forth, Many are duplications of installations that have been recently constructed, sort of carbon copies but perhaps arranged differently. The trend has been to incorporate loop tracks, rotary dumpers, indexers and, of course, the snivel coupler equipped unit train. How that the energy crisis has increased the use of coal, there has been a tremendous Increase in applications for permits to construct rail to river coal loading facilities. This paper is different. It does not describe any single existing facility, but is given to alert prospective terminal owners and engineers that there are items that require considerable study and evaluation beside merely selecting an indexer, car dumper, stacker, ship or berg loader and so on. An important item is the selection of the railway car which in turn can affect the selection of the method of loading and unloading. Let us list a few of the items that should be considered and discuss the areas that require examination:]

Jan 1, 1979

By S. Tyson

The American Coal Ash Association, Inc. (ACAA) is an organization of producers and marketers of coal combustion byproducts. Since 1968, the goal of ACAA has been to gain recognition and acceptance of ccbs as an engineering material on par with competing virgin, processed and manufactured materials by advancing ccb uses that are technically sound, commercially competitive and environmentally safe. The use of ccbs is affected by local and regional factors including production rates, processing and handling costs, transportation costs, availability of competing materials, seasonal adjustments, and the experience of materials specifiers, design engineers, purchasing agents, contractors, legislators, regulators, and other professionals. An annual, survey of coal-burning electric utilities is conducted by ACAA to determine the quantities of ccbs produced and used in the USA. In 1993 approximately 88.5 million tons of ccbs were produced in the form of fly ash, bottom ash, boiler slag and byproduct from flue gas desulfurization (FGD). Approximately twenty-two percent of the combined production of these byproducts was used, while the remaining portion was deposited in disposal areas. The major markets for ccbs include cement and concrete products, structural fills, road-base layers, mineral filler in asphalt, grit for snow and ice control, blasting grit and roofing granules, grouting, coal mining applications, and waste solidification and stabilization.

Jan 1, 1995

By George H. K. Schenck

It seems appropriate to review the history of mechanization of our underground coal mines at this time when many favorable flags are flying for this industry. It is a reasonable hope that such a review may stimulate thinking as to the directions that new technological developments are apt to take and in which members of the Society of Mining Engineers are destined to play important roles. Discussion of the relative importance of the various changes that have taken place since the advent of electric power provides the starting point. It is in the economic factors utilized that we find conditions which permit more efficient utilization of the capital committed to the industry. Concepts rather than specific items are emphasized in the following discussion because once the value of a concept, such as mechanical conveyors, is established, it then spawns many variations which are not significantly different. The shift from animate to inanimate energy has been the most important change in the modern industrial scene, including coal mining. Although introduced into coal mines for some purposes early in the period of general electrification, the coal industry adopted mechanical power relatively slowly, and 1944 was the first year in which a majority of deep-mined coal was mechanically loaded.

Jan 1, 1968

By F. Segobia, M. Portal, F. Ysla, L. Goicochea

It is our responsibility to promote responsible and sustainable mining with new generations, promoting a culture of equality and respect. To fulfill this commitment, we are working with the SME UNC Student Chapter team, Newmont Yanacocha, BRG Women and Allies and the Museo de Agua y Tierra (MAT) to carry out the “Building our future” project. It is our responsibility to promote responsible and sustainable mining with new generations, promoting a culture of equality and respect. To fulfill this commitment, we are working with the UNC SME Student Chapter team, Newmont Yanacocha, BRG Women and Allies and the Museo de Agua y Tierra (MAT) to carry out the “Building our future” project. This project seeks to instill in new generations the importance of mining, integrating sustainable development objectives. We have the participation of Newmont Yanacocha and external professionals, who share their life stories and inspire participants from rural and urban educational institutions to pursue their dreams and aspirations. We believe that this project is important because it will help new generations understand the importance of mining and its role in the development of the country, covering the economic, environmental and social spheres. Since its inception in 2022, the project has positively impacted more than 500 participants.

Feb 1, 2024

By Stanley A. Bunk, Desmond J. Bruyns

The purpose of roasting gold ores is to release for extraction, typically by cyanidation, the small particles of gold which are surrounded by refractory stone. The roasting simply opens up passages for the penetration of solution into the interior of the ore particles. This is accomplished by the removal by volatilization or formation of volatile oxides of certain constituents such as sulfur, arsenic or antimony. Temperature is an important parameter. High temperatures tend to form a dense iron particle rather than a "spongy" calcine. The dense iron particles result in lower gold recoveries. High temperature can cause melting of some components which also results in gold encapsulation. Roasting of refractory gold ore concentrates has been practiced for decades. Multiple hearth, rotary kiln and muffle reactors were first used for roasting. Fluid bed roasting provided a low capital cost, low maintenance technology with better process control and soon became the favored technology. The first fluid bed concentrate roasters were commissioned in the late 1940's. Early fluid beds were "bubbling" type. Environmental considerations did not significantly impact on the design. Feedstocks were highly exothermic and reaction rates were relatively rapid. Roasting today must compete with other technologies for treatment of refractory ores. Ore bodies which are not

Jan 1, 1993

By Donald R. East

The impacts of the economic storage or disposal of mill tailing wastes are becoming more important to the mining industry as environmental regulations become more demanding. Mill tailings have long been considered the stepchild of the extraction process and have not, until recent years, been treated as a separate entity of the mining and milling process with distinct and complex physical and chemical characteristics. As a waste product, the economic value of mill tailing is usually very small whilst economic and the environmental liabilities can significant. be Disposal of tailing is commonly identified as the single most important source of environmental impact for many mining projects.

Jan 1, 1990