Search Documents

By Philip U. Santacroce, James H. Meinholz

One-half of the $607 million Conveyance construction portion of the Milwaukee Metropolitan Sewerage District's Water Pollution Abatement Program is completed or under contract. 12,200 m (7.5 miles) of tunnel boring machine (TBM) driven rock tunnel from 2.5 m (8.0 ft) to 9.9 m (32.3 ft) diameter has been completed. This paper presents a review of TBM performance and a discussion of the pertinent geological conditions of the area.

Jan 1, 1987

By Kurt Burg, Allen Reicks

Tapered clamping devices have been used successfully over the years to transmit torque and bending loads from conveyor drives to conveyor belts. Proper design and application is important in the successful operation of these key components. This paper includes a historical review of component design and application and an overview of the important dynamics and limiting factors. Actual applications and simulation models are used to demonstrate the correct use of these devices.

Jan 1, 2002

By Joe Scheuering, Don Poulter, John Trirnble

Closure of the Grey Eagle Mine tailings impoundment is an example of closing a "wet" tailings impoundment at the cessation of milling operations. This paper presents a summary of tailings cover design and construction, tailings deposition sequences to facilitate closure, construction schedules, costs, and post-closure monitoring. Permit requirements which influenced the design and construction of the tailings are summarized. The performance of the cover and post-closure monitoring issues are also discussed.

Jan 1, 1995

By F. Allen Meek

The Upshur Complex of Island Creek Coal Corp. consists of approximatly 35.000 acres of both surface and deep mine researves located in Upshur County West Virginia. The principle seams on the researve are the Middle and Lower Kittanning. Other mining in the area during the late 1960's and early 1970's produced surface mines that exhibited severely acidic drainage characteristics both during the mining phase, and after reclamation was completed. The Buckhannon River, the principal drainage for the area, is a high quality, lightly buffered stream, that is periodically stocked with trout. Because past mining had caused post mining acidic discharges and the Buckhannon River was a valuable recreational resource, mining permits for the area were put on hold by regulatory authorities, until solutions to the acid mine drainage questions could be addressed. In 1978, the director of the West Virginia Department of Natural Resources appointed a Task Force consisting of Industry, Regulatory. and Academlc participants. This Task Force was charged with gathering information and evaluating field procedures used during mining to prevent acidic mine drainage. In 1979, the group published a document titled "Suggested Guidelines for Mining in Potentially Acid Producing Overburdens" which summarized material handling and mining procedures that could be employed to help prevent the occurrence of post mining acid mine drainage. In 1982, a Technical Advisory Committee was appointed consisting of well known researchers in the field of acid mine drainage prediction and prevention. The group was charged with the task of conducting research in the field of acid mine drainage prevention. Mining conducted at the Upshur Complex between 1979 and 1986 employed various acid mine drainage preventative techniques recommended in the suggested guidelines manual and techniques concurrently being researched by the Technical Advisory Committee. Costs for the various techniques were documented and the resulting post-mining water monitored. The results of these evaluations are used by Island Creek in the planning of future mining operations in potentially acid prodcuing environments

Jan 1, 1991

By Peter Moser, Michael Hitch, Michael Tost, Susanne Feiel

"Impact and Benefit Agreements (IBAs) are intended to be a negotiated agreement between an industrial proponent and a community, local or regional citizens’ organization. Although the elements have grown over the past two decades from a simple agreement to exceedingly complex legal frameworks, the intention remains the same: to outline the roles and responsibilities of the two stakeholders and the natural resource development on their lands beyond environmental assessment. These agreements were born out of comprehensive indigenous land claims and have become the cornerstone of community engagement today in most indigenous nations. In the case of mixed communities, those that have beneficiaries of land claims and those who are not, social acceptance remains uneven and reflective of an unequal distribution of decision-making power (political ecology). This Differential Social License can cause conflict and a breakdown of the societal fabric that binds communities of diverse populations, resulting in inequality, fictitious wealth generation and failure of infrastructure. This paper presents a case study of how the development of Differential Social License developed in the Hamlet of Cambridge Bay, Nunavut as a result of an IBA negotiated between Tahera Diamond Corp. and the Kitikmeot Inuit Organisation in 2004 for the Jericho Diamond Mine.Introduction / Background Social license (social license to operate or SLO) has become an essential part of the social governance ‘toolkit’ demanded by mining stakeholders in today’s world. Stakeholders are now insistent that companies operate more closely under the tenets of sustainable development and provide for an increased level of community participation. Social license is not simply a matter of communicating with a community, to earn its consent for or acceptance of a project. It requires that we engage with the individuals and organisations who ally themselves with communities, or who sometimes side with dissident factions of a community. SLO is a process associated with and informed by political ecology or the recognition that unequal decision-making power exists amongst stakeholders."

Jan 1, 2017

By Albert W. Evans

Introduction Engineering Health and Safety is concerned with the understanding of the complex interplay between the risk of injury with technological ,environmental, individual, organisational and legal factors. With this understanding, the design and decision making processes can be balanced with the other objectives of industry and employment to arrive at solutions which place appropriate controls on technology and other aspects of human activities to prevent disease and injury to personnel in the coal mining industry and the design of safe production machinery and ancillary equipment. Advances in the detection and diagnosis of causes of diseases and the need for engineering health and safety in the coal mining industry has increased the need for appropriate education and training. Hazards arise in many forms; exposure to toxic chemicals, escape of radio - active materials, explosion of pressure vessels, contact with moving machinery, exposure to dust, environmental dangers such as excessive noise, high temperatures and manual handling etc. As technology advances, these dangers become more complex and less clearly defined and less easily perceived. Consequently, the ways of controlling the dangers also become more complex and wide ranging. The need to educate and train people in coal mining applications of engineering health and safety has been enhanced over the last five years and courses should be established to fulfil the need for competent people to deal with the problems which modern coal mining technology creates together with the legislation that governs engineering health and safety and to carry out research and development work in the coal mining industry. Industrial Involvement The engineering health and safety experts must be prepared to take a more active part in monitoring conditions that exist in the mining industry, and not design from information obtained from the mechanical, electrical and hydraulic expertise and off-the-shelf components from other industries. Surveying and control of the operating environment must be essentially the concern of the engineering health and safety experts and, whilst it is not possible to create a perfect environment for each machine, every effort must be made to minimise failures and hence plan for designs which will maximise

Jan 1, 1986

By B. K. Baird, P. C. Satchwell

The application of cutoffs during and after pit optimization is examined for a lower-grade multimetallic copper deposit. Pit optimization requires calculation of the net revenue associated with each mining block. The calculation incorporates parameters such as metal prices, grades and expected recoveries, mining and processing costs, smelting and refining charges, and penalty element and royalty charges. Sensitivity analysis during pit optimization reveals which parameters have significant effects on the total contained resource tonnage and total contained nondiscounted revenue in the optimized pit. The cumulative effects of changing several of the more-significant parameters are investigated The application of a copper cutoff grade to a block inside the optimized pit could result in the less-than-optimal extraction of the resource. A block with a copper grade below the applied cutoff could be economic due to the presence of other metals. Conversely, a higher-copper-grade block may be subeconomic. Also discussed are the merits of applying a copper-grade cutoff, an "equivalent-grade" cutoff and a dollar-per-ton cutoff to blocks inside the optimum nit.

Jan 1, 2002

By James Matlock

The announcement of a minable reserve of 13.6 Mt (16 million tons) averaging 0.9 g/t (0.027 oz per ton) Au and 2.4 g/t (0.71 oz per ton) Ag for the open pit-heap leach reserve at Red Mountain No. 3 in Ouray County, Colorado, by Cornucopia Resources in November 1985 brings another open pit-heap leach precious metal ore body to the production stage. With about 8.2 Mt (9 million tons) of waste and metallurgical studies showing acceptable recovery rates, low reagent consumption, and good final percentage recovery, Red Mountain is a discovery that will add to the precious metal inventory of the US. Frank Baumgaruler of Denver, CO, recognized the precious metal potential in Red Mountain No. 3 and acquired all of the old claims. James Matlock conducted a field reconnaissance over Red Mountain No. 3 independently of the Baumgartner activities and recognized epithermal alteration and mineralization in the Tertiary volcanics. He recommended acquisition of the ground and was able to obtain rights and drill six core holes for Amoco in 1982. Amoco drilled a further nine core holes in 1983, but then dropped the property. Cyrano Resources examined the data and through its consulting geologist, V.F. Hollister, acquired the rights dropped by Amoco. In 1984 Cyrano began further drilling of the ore zone demonstrated by Amoco but they were then acquired by Cornucopia Resources. Cornucopia completed development of the property and commenced the permitting process in 1986. The property was recognized as a disseminated gold deposit by both Baumgartner and Matlock, and both deserve credit for properly evaluating mineralized outcrop in the Tertiary volcanics. However, Cornucopia recognized the profit potential in the heap leach exploitation of the ores and de- serves credit for completion of premine feasibility studies. The discovery is clearly a geological one, but the premine engineering studies were essential to the conversion of the prospect to a commercial mining enterprise. The deposit lies on the circular bounding fault of the Silverton caldera. Two reprints follow that help understand the geologic setting of the ore controls.

Jan 1, 1990

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. ng of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

Jan 1, 2008

By Tony Walsh

Timely disclosure of information germane to the taking of investment decisions makes an essential contribution to ensuring the growth, efficiency and integrity of our capital markets. It is a core contributor to the maintenance of fair, orderly and transparent markets. The communication of relevant and comprehensible information to the investor plays a vital part in fostering investor confidence, thereby building depth and liquidity in our market. Australian Stock exchange Limited ("ASX") has had and continues to have a rewarding partnership with the mining industry to develop and recognise reporting standards, the JORC Code. This allows ready comparability and investor understanding of the mining investment vehicle. ASX's mining market has been successful because of the high reporting standards in the JORC Code and the high standards of professionalism and the intellectual capital that has been built up among the participants - the mining professionals, brokers, analysts, mining investors, professional advisers and the market operator. The balance of knowledge and understanding among these participants combined with the competition for capital, contributes to the standards for our mining market in a way that the market operator simply cannot replicate by market rules alone.

Jan 1, 2003

By P. N. Eksteen, G. E. Greig

The South African mining industry currently installs about 6 km per month of plastic pipes for conveying compressed air and water. Plastic pipes have a number of desirable properties and are favoured by many mining engineers because of their low mass, which facilitates ease of erection and assembly, and their excellent corrosion resistance and durability. However, they are combustible, and if involved in an underground fire can contribute to the overall toxicity of the combustion gases emitted. Furthermore, plastic pipes have the potential to conduct a fire from one part of a mine to another, and, by so doing, exacerbate an already hazardous situation. The limitations of small scale tests and the need to establish a large facility where underground conditions could be simulated was recognized by the South African mining industry. This paper briefly describes the Industry's full scale fire test facility and presents the conclusions drawn as a result of a number of full scale combustibility tests conducted on pipes manufactured from unplasticized Poly Vinyl Chloride (uPVC) and High Density Polyethylene (HDPE). Based on these findings, some practical solutions to prevent the spread of fire along the length of pipe columns of various pipe diameters and suspension configurations are presented. Recently some new and exciting developments in the field of intumescent coatings have occurred which are proving effective in minimizing the incidence of fire underground on South African mines. The potential benefits of these coatings are briefly discussed. INTRODUCTION Plastic pipes used underground on mines are predominantly in the form of protective cladding on insulated chilled water pipes and as service pipes for the conveying of water and compressed air to the workings. Plastic pipes have found wide use in the aggressive environmental conditions encountered underground due to their favourable properties relative to steel; these include being lightweight, easily installed and virtually immune to corrosion. However, plastic pipes are inherently combustible and can contribute to the overall hazard in three ways: (i) they are easily ignitable and can provide the initial fuel for a fire. (ii) once ignited, they can propagate a fire along their length and by so doing ignite other combustibles in their path, thereby contributing significantly to the overall conflagration. (iii) they can contribute to the overall heat, smoke and toxic gas emissions from a fire. While conscious of the value of small scale fire tests, the South African mining industry recognized the need for full scale testing to determine the combustion characteristics of plastic pipes under conditions closely approximating those underground and, as a consequence, a full scale fire tunnel test facility was commissioned with the objective of being able to (a), accurately evaluate the potential hazard of the various types of the plastic pipes found in mines, (b) use this information to suggest suitable fire engineering practices to minimize the hazard and (c), to practically verify the efficacy of the practices suggested. THE FIRE TUNNEL The fire tunnel is situated on a mine in the Western Transvaal and is 40 m long with a cross section of 3 m x 3 m which is typical of many haulages currently in use in South African gold mines. The ventilation drawn through the tunnel is provided by a 110 kW centrifugal exhaust fan and air velocities can be varied from 0 to a maximum of 5,8 m/s.

Jan 1, 1993

By T. M. Gurr

It is estimated that in excess of one-half million chemicals are used throughout the American workplace. Hundreds of new chemicals are also being introduced into the workplace annually. Exposure to some of these chemicals can be harmful to workers and to the environment. The Occupational Safety and Health Administration (OSHA) estimates that approximately 25% of the U. S. labor force or approximately 25 million workers are exposed to one or more chemical hazards each year. OSHA has determined that this poses a serious problem for workers exposed to such chemicals. Chemical exposure may cause safety and health problems. Health problems can include a cause or contribution to heart ailments, kidney and lung damage, sterility, cancer, burns, and rashes. Safety hazards can include the potential to cause fires and explosions and other serious accidents.

Jan 1, 1989

By R. J. Matetic

The impact of longwall mining on the local hydrological regime has become an important environmental focal point. Unfortunately, only a few studies have addressed the timing and range of well fluid level fluctuations and the associated ground movement. Furthermore, even fewer studies have determined the influence of longwall mining on water quality. The U.S. Bureau of Mines is providing insight into this environmental concern through a program of field case studies. One such study was conducted in Cambria County, PA where five observation water wells were drilled above two adjacent longwall panels. In this study, three wells were completed as nested piezometers and the remaining two served as producing wells. The piezometers were positioned along a line oriented subparallel to the longwall face and were located at the centerline of each panel and over the intervening chain pillars. The piezometers were designed to monitor fluid level fluctuations in both shallow and deep water-bearing zones. Slug tests were conducted before and after mining to characterize changes in hydraulic conductivity of the respective water-bearing zones. Pressure transducers and data loggers were installed to provide continuous fluid level fluctuation data as mining developed through the study area. The producing wells were drilled to provide water quality information. One well was located directly above the centerline of a panel and the other was positioned over the panel's set-up rooms. The wells were designed to simulate domestic use and were produced daily, for four hour intervals, throughout the study. Samples of the produced water were collected before and after mining progressed through the area. In addition, an array of monuments was installed near the study wells and was periodically surveyed to characterize mining-induced surface deformations. This study shows that: a) the observed changes in ground water chemistry did not affect the potability of the water; b) short-term major water level fluctuations occur at the approximate time of undermining; and c) water level recovery begins before the process of subsidence is complete.

Jan 1, 1986

By N. I. Fedunets

The development of variousworks on automatising of operational processes at coal¬extractive and coal-mining enterprises introduces an ever growing necessity to carry out investigations in the wide range of problems concerning the possibitity of joint functioning of different levels, which seems impossible without the use of integrated systems of passing on and prossessing the information on the basis of modern calculating machines and other means of automation. This view on the problem of automation of the enterprise operation presupposes that the structure of automated operational dispatcher control (AODC) should be very closely connected with that of integrated data processing system! In this case the AODC structure from the point of view of automation of its functions (or operations), i.e. from the point of view of informational techniques coinsides in general with the structure of dispersed information and calculating network (ICN), realizing the passing on and processing of the information as well as solving the functional tasks on the basis of local calculating networks of electrical calculating machines with correspond to different levels of AODC and located with regard to productional hierarchy of operational dispatcher control (ODC). In this approach however the use of dispersed, ICN gives opportunity to. realize the possibility of action only with realisation on the CM of algorithmic' task of ODC, when a dispatcher 'is the lastto make a final decision.. At the mining enterprises it's rather difficult for a dispatcher to make a final decision because of the great variaty of productional situations, the presence of contradictions and a number of other subjective factors which often lead to the dispatcher's mistaks causing great material losses of the enterprise. Hence the necessity arises to automize and formalize making a decision and including the expert systems (ES) into the ontour of AODC, which enables the dispatcher 2to get a neeessary advice in different situations, especially in case ofemergency on the basis of establishing the mechanism of logical layout of non-formalized data base (DB) procedures relying upon the background knowledge and experience of experts. The presently presented in this paper theory of establishing the. ISAODC on the basis of dispersed ICN and expert systems is aimed at trasformation ofoperational' tasks of the higher level into the technological ones, at solving the tasks of diagnostics and forseeing of the process of production, with a dispatcher getting an opportunity of making qualitative and effective decision concerrning the choice of operational impacts in actual time on the basis of generalization the realisation of presented conception must, as has been already mentioned, be accomplished only on the basis of the foundatoin of the united dispersed informational - calculating network of electrical calculating machines.. This includes ICN which would be operating in . different operational contours. . From what has just been said it followsthat the ISAODC Structure will conside with that of DICN (in our case) and hence all the problems of ISAODC structure would be regarded as the questions of DICN.

Jan 1, 1992

By T. L. Heidrick

Late Cretaceous-early Tertiary Cordilleran porphyry Cu-Mo districts and their consanguineous Zn-Pb-Ag-Au-W vein and replacement deposits of the Rocky Mountain region comprise one of the largest, best studied, diverse, complex, puzzling, and richest compound metallogenic provinces on earth. A concise space-time definition of intermineral plate, regional and local structure-tectonic frameworks is crucial to deciphering their diachronous metallogeny and enhancing the explorationist's odds of future discovery.

Jan 1, 2013

By W. M. Kidd

INTRODUCTION Uranium mine inspection in Canada forms one element of the enforcement of the Atomic Energy Control Act; it is under this Act that all Canadian uranium mines and mills are licensed to operate. Inspection duties are carried out by a small core staff of federal government inspectors (working for the Atomic Energy Control Board (AECB)) largely supplemented by provincial mine inspectors working on behalf of the AECB. Unlike most resource extraction in Canada, uranium mining is under federal jurisdiction and consequently it was the AECB who decided in 1975 that changes in the Canadian uranium mining industry, particularly its expansion and the expanding role of the mine inspector in the limiting of exposures, warranted the offering of a special radiation protection training course. The Uranium Mine Inspector Training Course (UMITC) was first conducted in 1976 at the Elliot Lake Centre in Elliot Lake, Ontario. Subscription for the course was not limited to mine inspectors to enable union stewards, management personnel and provincial/federal labour inspectors to attend. This paper will present an outline of the course content, the format of its presentation and non-curriculum aspects of running a course of this type in uranium-producing community. The core lecturers for UMITC are drawn from the Radiation Protection and Uranium Mine Divisions of the AECB. In addition, guest lecturers are invited from universities and medical research centres together with industry professionals and government researchers. In all some twenty-four plus presentations are made over the first five days of lectures. The program topic areas, hazards, controls, measurements, record-keeping and health effects are preceded by an intensive half-day session on radiation fundamentals. TOPICS Hazards [Dust] A review of the dynamics of airborne particles including the effects of particle size, gravity and wake-turbulence on the behaviour of dust clouds. Associated topics are migrational aspects of dust particles and specific dust-generating mine operations. [Radiation] Canadian uranium mines are increasingly diverse in nature ranging from large scale low-grade underground operations in Elliot Lake to smaller high-grade open pits in Saskatchewan. Papers are presented on assessments of internal and external exposure, the metabolic pathways of ingested or inhaled radiation and the specifics of mine and mill hazards. Radiation hazards are further broken down into gamma surveys of uranium mines, radon daughter concentrations and problem areas. Controls The relationship between mining methods and the operating environment is critically important to ensuring safe working conditions. This refers to both the selection of machinery/devices, etc., and to engineering controls which are instituted to remedy problems created by new technology. UMITC examines a number of possible mining techniques, their criteria for selection and impact on the working environment. Control measures, ventilation practices and design, the need for continuous water misting and special open-pit precautions are presented. These lectures frequently conclude with suggestions for better operating guidelines for mine ventilation systems and the need for greater co-operation between the ventilation department and the underground crews. Measurements Uranium mining regulations stress the need for a high standard of exposure monitoring, statistical planning and record-keeping. [Statistics] Although many course participants are well versed in statistics, certain fundamentals are repeated and include, the concepts of mean, variance, standard deviation and standard deviation of the mean. Confidence levels, decision-making based on sample statistics and statistical records are also discussed. [Dust Measurement] Dust measurement is particularly critical in the mines where the high silica content of the ore body, such as those at Elliot Lake, results in the continuous generation of dust. Sampling practices, filtration, impaction, thermal impaction and electrostatic precipitation are explained together with the methods of counting samples to determine free silica. Konimetric and gravimetric techniques for dust sampling are compared and contrasted. [Radiation Measurements] Both collective and personal dosimetry systems are used in the Canadian uranium mining industry and lectures are presented on each. Techniques and possible sources of error are discussed for a variety of radon and radon daughter measurement methods - Lucas method, Tsivoglou and modified Tsivoglou, Kusnetz, Rolle. Instant working level meters and personal alpha dosimeters are explained in terms of calibration, maintenance, readout and estimation of accuracy. A lecture outlining dose estimation by means of bio-assay, whole-body counting and the use of TLD's concludes the topic. Record-Keeping An overview of the problems of changing limits,

Jan 1, 1981

By W. T. Plummer

• The SuperBowl is a fluidized bed, semi-continuous, enhanced gravity separator for gravity gold recovery. The market for this type of equipment has, until recently, been dominated by a single supplier. Many mineral processors have encouraged the SuperBowl designers to develop competitive equipment for obvious reasons. • The primary beneficiary of competition in this field will be the mineral processing community because legitimate competition fosters continuous improvement in product and price.

Jan 1, 1996

By R. Jovanovic

The main technological indicators of copper flotation which determine the level of revenue per mass unit of processed copper are utilization and the content of copper in concentration. This study describes the economic-technological model of copper flotation which can help determine, for the given technological and market conditions, an optimal percentage of copper in concentration, whereby the maximum revenue is achieved per ton of the processed ore in the process of flotation.

Jan 1, 2006

By T. Maniatis, T. Pickett, B. Wahlquist

Biological destruction of cyanide in mining waters has been demonstrated effective in the lab and in the field. Applied Biosciences Corp.’s ABMet water treatment technology is used in the mining and other industries for the removal of various inorganic contaminants including metals and nitrate. An aerobic ABMet-CN process has shown great promise in efficiently and effectively removing cyanide from even very cold waters. Bench and pilot data will be presented.

Jan 1, 2004

By V. Y. Kirillin, V. A. Rumjantsev, S. A. Tchesnokov, Yu A. Veksler, V. F. Kalmykov, A. N. Telgarin, A. T. Shakirov

Mining in outburst hazard seams may be safe and effective if some preventive measures, such as lowering gas and rock pressure as well as speed regulating of a continuous miner in cutting the seam would be practised. The driving speed should be optimal as the low speed lowers labour productivity but the high speed may cause gaso-dynamic phenomena. At this mine the driving speed is regulated by seismo-acoustic control of the seam condition.

Jan 1, 1985