Search Documents

By Richard M. Crowell, John W. Shield, Todd J. Harvey

Facing lower gold prices, gold mine operators throughout the world are seeking ways to reduce costs for treating refractory sulfide ores. Many gold mines, currently producing oxide ores, have underlying refractory sulfide deposits and the operators could extend the mine life by processing these sulfides. Fortunately, oxidation technologies for refractory ores need not be complex nor costly. GeoBiotics, Inc. has developed heap biooxidation technologies (GEOCOAT™) for treatment of refractory gold ores and concentrates. GEOCOATTM uses simple low cost unit operations common to heap leaching of gold and copper ores. The cost effectiveness and flexibility of GEOCOAT™ heap biooxidation allows mining companies to expand operations to include refract01y ore. In addition, GEOCOAT™ can be utilized to supplement or replace existing oxidation processes such as roasting, autoclaving, or agitated tank biooxidation, and to treat a lower resource grade than is currently economic. The GEOCOAT™ technology involves coating sulfide concentrates onto sized support rocks and biooxidizing the sulfides in a heap configuration. After biooxidation the concentrate is stripped from the support rock, neutralized and leached in conventional cyanidation facilities. Ashanti Goldfields Company Ltd. (AGC) produces over 885,000 ounces of gold per year from oxide and refractory ores at its Obuasi operations in Ghana. Refractory flotation concentrates are treated in roasters and in the world's largest stirred tank biooxidation facility. In August 1998, AGC and GeoBiotics jointly constructed and operated a field demonstration heap of the GEOCOATTM process at the Obuasi operations. The heap contained I 082 tonnes of support rock and 125 tonnes of concentrate. The heap was approximately 19 meters square at the base and 3.8 meters high, and ran for 88 days after which the concentrate was reclaimed. Average gold recovery after biooxidation was 91.5% with a NaCN consumption of 8.6 kg/t. Baseline gold recovery by direct cyanidation of the concentrate was 53.8%.

Jan 1, 1999

By Jonathan M. Pachter

Introduction The Bailey mining complex is located in Greene County, PA, in the Talley Run valley. It includes two Pittsburgh No. 8 seam deep mines (Bailey and Bailey No. 2), a coal preparation plant, and two refuse areas. Clean coal is shipped from the complex by way of a 24-km (15-mile) rail spur. It con¬nects to the Monongahela Railroad in Waynesburg, PA. In early 1981, Consolidation Coal Co. (Consol) began a permitting effort aimed at building the mine. Construction began in Dec. 1981, less than six months after the first application submittal. Clean coal was produced by the Bailey preparation plant in Sept. 1984. Several factors allowed quick permitting at Bailey. Effective project planning, including early formulation of a project planning team, and identification of red flag issues helped. So did innovative responses to environmental questions, and development of environmentally sound project designs. Forming a project planning team Consol management decided that Bailey mine construction had to begin in late 1981. A project permitting team was immediately formed to see that this goal was achieved. Team members included a project manager and personnel from Consol's engineering, environmental, and operating departments. Communications among all team members was crucial in obtaining the various state and Federal environmental permits. All project permitting team members participated in weekly meetings during application preparation. Discussions at these meetings ranged from recent public contacts, to application content, to environmental design considerations. Establishing a project manager was critical to the team's success. The project manager was responsible for seeing that permit acquisition, facility construction, and operation of the mining complex proceeded on schedule. The project manager had the final word, mediated disagreements, and frequently served as project spokesman to the public. Identifying red flag issues Red flag issues are those environmental factors with the most potential for delaying the schedule or stopping the project. The first red flag issue identified was organized local opposition. This opposition had completely derailed a US Soil Conservation Service proposal to build a multipurpose dam on Enlow Fork, a short distance

Jan 9, 1985

By Michael G. Nelson, Brandon J. Peterson

Currently, decisions made by mine management are usually based on economic analysis and predetermined rating systems and tables. As financial and other constraints on mining operations become more severe, more accurate methods are required. Discrete-event simulation programs have been used successfully in many mining applications, including the simulation of open-pit, truck-and-shovel operations. However, these simulations could not model complex systems well enough to provide the detailed modeling of the haulage roads and other mining operations that is needed today. The recent advances in computing technology combined with the recent abilities of simulation to realistically simulate complex systems and visually present results in 3D have made simulation a more detailed and valuable aid in the evaluation of mining projects.

Jan 1, 2002

By A. Mahtab, S. Xu, P. Grasso, B. J. Fu

The large population base, complex geology of the large land mass, and notable commercial activity have accelerated the development of underground construction market in China. The projected lengths of underground openings per year in the various sectors are: hydro-tunnels, 180 km; coal mine entries, 40 km; transport-tunnels, 300+ km. An example of the mega projects (being planned by the Government) is the water supply scheme for connecting Yangtze river to Yellow river involving 131 km of water tunnels with a diameter of 8-10m. Several large projects are highlighted in the paper with reference to the schemes for generating hydro-power, mining of coal and minerals, and constructing transportation networks. The related problems of construction and geomechanics are outlined.

Jan 1, 1995

By Yu Qixiang, Wu Yanyun, Guo Junfeng

The experience of mining coal and gas outburstprone coal seams shows that the degree of outburst danger in various coal seams and even at different parts of the same seam are quite different, and that to deal with them respectively in different ways will not noly be significant to safety but bring us remarkable economical profit, Based on the statistical data,including elght static and dynamic factors, gathered from coal and gas outburst spots at Nantong colliery in Chong Qing district of China, this paper has partitioned the degree of outburst danger of the No. 5 seam there by means of Fuzzy Clustering method. Because in the evaluation multiple indices have been considered, the result of partitioning is identical to practice and more efficient in applications.

Jan 1, 1991

By G. Wang

Industrial minerals processing has gained importance lately, not only due to its wide range of new and regular applications in processing different industrial minerals, but also due to the strict specs under which products are commercialized. Among the processes applied to industrial minerals, flotation is a leading technology. The laboratory study and commercial operation demonstrate that the sulfonated reagents are very effective collectors for industrial minerals. This paper compares synthetic petroleum sulfonate with fatty acid on iron reduction in glass sand processing and describes the effect of conditioning pH on iron reduction using synthetic petroleum sulfonate as collector, the effect of molecular weight of natural and synthetic petroleum sulfonates on their flotation performance and the enhancement made for certain products.

Jan 1, 2011

By R. V. Ramani, R. Natarajan, A. Bhattacherjee

Industries in general, and mining in particular, have become safer than ever before. However, there is a need to increase the search for the causes of mining work-related injuries and to contribute to their reduction, as required, through job redesign, work procedures and worker training. Mine accident and hazard control must be practiced in a manner consistent with the overall objectives of the mine management, which include the optimum allocation and effective utilization of the resources. The purposes of this paper are to: • present a set of analytical tools to analyze injury experience data. • apply these tools on a case study example, • discuss the results of the case study, and • identify the application limitations and the future research needs.

Jan 1, 1993

By Jeffrey C. Reid

Computer processing and high resolution graphics display of geochemical data were used to quickly, accurately, and efficiently obtain impor¬tant decision-making information for tin (cassiterite) exploration, Seward Peninsula, Alaska (USA). Primary geochemical dispersion patterns were determined for tin-bearing intrusive granite phases of Late Cretaceous age with exploration bedrock lithogeochemistry at the Kougarok tin prospect. Expensive diamond drilling footage was required to reach exploration objectives. Recogni¬tion of element distribution and dispersion patterns was useful in subsurface interpretation and correla¬tion, and to aid location of other holes. Tin was its own best pathfinder. Arsenic, also a useful pathfinder element, forms a discrete halo peripheral to tin mineralization. The arsenic halo is expressed in hand specimens by asenopyrite and/or scorodite staining.

Jan 1, 1989

By Mandira Madhuchhanda, N. B. Devi, P. C. Rath, R. K. Paramguru, K. Srinivasa Rao

An experimental investigation of the dissolution of three base-metal sulfide minerals, namely, CuFeS2, ZnS and PbS, in hydrochloric acid medium in the presence of manganese dioxide is reported. Polarization measurements and leaching studies were employed in the study. Dissolution occurred in the following three ways: by the cyclic action of the Fe3+/Fe2+ redox couple, by galvanic interaction between Mn02 and the sulfide minerals, and because of chlorine evolution from the system. The later two routes were found more effective at higher HCI levels. PbS appeared to be oxidized easily, whereas CuFeS2 was the most difficult to dissolve. ZnS dissolution fell in between PbS and CuFeS2.

Jan 1, 2002

By J. A. Dille, J. P. Hand, J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Co. to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the company's main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received additional attention in recent years. An objective that no coal shipment should exceed any contract or company-imposed coal quality specification has been successfully met. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed.

Jan 1, 1987

By D. R. Kalasky, J. M. Mutmansky, B. Kolonja

This paper considers simulation of truck dispatching systems using maximum expected production of the truck-shovel system as the measure of performance. Two analysis methods are utilized: multiple comparisons with the best (MCB) and the combination of MCB with the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. Results show that the combined procedure of MCB with CRN is the superior tool to use to reduce the total number of replications needed to ensure the specified probability of correct selection from a number of systems. In this case study, MCB with CRN reduced the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1995

By Eugene Honeycutt, David Gallagher, R. E. Melley, Nick Madison

Drummond Co. Inc.'s Shoal Creek Mine slope conveyor is the highest lift, highest horsepower, highest tension conveyor system in North America. The system has a capacity of 4950 t/h (5500 tph), a vertical lift of 360 m (1180 ft) and a total connected power of 6000 kw (8000 hp). The mine will include 2 longwall machines and 5 to 7 development sections. Annual raw production will approach 9 million tly (10 million tpy). This paper describes the early investigation of system capacity, haulage system options, and the final selection of a single flight belt conveyor. It will review the basic system de- sign and equipment selected. Also included will be some highlights of the installation of the conveyor system.

Jan 1, 1996

By M. Jawed

Coking coal reserves in India are distributed geographically in Giridih, Raniganj, East Bokaro & Jharia Coalfields (J.C.F.). 97% of prime coking coal in JCF coming through underground mines is credited to Bord & Pillar mining systems inspite of the fact that it results in heavy mining losses. The cost of mining in B & P mines has been much higher due to various factors. In this paper, O.R. model has been discussed with case study for optimizing the cost of production in operational underground mines. Also, a computer algorithm has been discussed using a schematic flowchart, which provides the trend of mining-losses 'in different mining, systems with changing design parameters and finally selects, the optimum mining system for undeveloped seams based on economic appraisal criteria.

Jan 1, 1989

By Bezalel C. Haimson

Long before excavation begins, the in situ stresses in the horizon of planned underground chambers can be measured by employing the hydrofracturing technique in existing exploratory holes. Such measurements produce the stress magnitudes and directions required for the rational design of rock structures. Two recent case histories are cited in which preexcavation stress measurements for the design of underground powerhouses proved very beneficial in the orientation of the chambers and the estimation of the stability and required support. A third stress measurement case is related to the preexcavation design of tunnels that will house doughnut-shaped superconductive magnets for the storage of electric energy. In all cases, expensive later modifications were probably prevented by measuring stresses early in the design stage.

Jan 1, 1976

By David E. Peterson, F. Merz

The Waihi Gold Mining Company Limited, Martha Hill Project was the first major hard rock mining operation following the resurgence of the mining industry in New Zealand. Because of its location adjoining a town and at the southern part of the sensitive Coromandel Peninsula, the operation received a high level of public scrutiny. Very srrict limits for effluent criteria had to be met and led to the necessity for advanced wastewater rreatment technology. The process technology selected was the copper catalysed oxidation of cyanide using hydrogen peroxide, with subsequent removal of heavy metals by precipitation and filrration. This paper discusses the adoption of environment limits together with the detailed description of the plant and design criteria. Data of the one year's operational history is also presented.

Jan 1, 1991

By H. N. McLeod, M. J. Thom

The use of cyanide in gold mining requires the careful handling and storage of cyanide rich tailings. Cyanide in groundwater can frequently be both persistent and mobile, so that tailings basins need to be designed to limit and collect seepage. Assessment of the potential environmental impact requires an understanding of the hydrogeologic regime, both before, during and after mining. Groundwater monitoring wells provide a basis for monitoring tailings pond behaviour and for assessing the impact of mitigative measures to reduce or control seepage. A case example of Cheni Gold Mines Lawyers Project in Canada is presented to illustrate the use of groundwater monitoring to determine the amount of cyanide degradation and attenuation between the tailings pond and the receiving environment.

Jan 1, 1991

By Harrie van Dijk

Feeding laterite nickel slurry into high pressure acid­leach (HPAL) autoclaves in an aggressive environment with slurries heated up to 200°C requires a special pump design. For decades the GEHO piston diaphragm pumps have been used for autoclave feeding at gold ore pressure oxidation plants with slurries up to l 77°C. Lessons learned from these installations have been instrumental in designing second generation feed pumps for processing laterite nickel with operating temperatures of 200°C and a flow rate of 400 m3/h. The Australian nickel industry is using momentarily 8 GEHO positive displacement piston diaphragm pumps. For this application six GEHO ZPM 900 "dropleg" pumps have been supplied to the Murrin Murrin project and two to Bulong.

Jan 1, 2000

By Rob Henson, Te-Lin Yau, Darryl Amick

The process industry faces tightening environmental regulations. In order to comply with these mandates, environmentally safe chemicals, such as oxygen and hydrogen perox­ide are becoming attractive oxidants. These oxidants appear benign but must be respected when involved in harsh environments. It is therefore important to address both the safety and suitability of materials selected for these environments. Otherwise, severe prob­lems, such as equipment failure or fire and explosion can occur. Laboratory and field experience will be used to discuss the perfor­mance of titanium, zirconium and Ti-45Nb alloy in piping systems for handling these environ­ments. Sealing methods for piping, pumps and valves of these metals will also be reviewed. For comparison, information on the performance of stainless alloys will be given.

Jan 1, 1993

By P. M. Lin

The problem of surface subsidence over abandoned mine lands is becoming more common due to the development of housing in suburban areas of abandoned mined lands. Subsidence can induce damage to estate properties, engineering structures and the environment. Houses, buildings, roads and utility pipelines may be fractured or broken or may collapse due to subsidence. The ground surface may be depressed and sink gradually or suddenly. The surface and subsurface water flow may be disrupted causing a change in flow pattern or depression of the water table. However, techniques for predicting abandoned mine subsidence are not yet well developed. Presently, one cannot predict when and where mine subsidence will occur. People have to wait until it occurs and then apply a suitable measure to remedy the damages.

Jan 1, 1990

By Jim V. Rouse

The decision to hold parallel conferences dealing with hazardous waste and mining waste grew out of the conviction that there were advantages to having personnel serving the two groups talk to each other, as both groups develop cost-effective and environmentally-protective solutions to present and future waste-disposal problems. There has been a certain amount of "reinventing the wheel" which could have been avoided by a better dialog between the two groups. The intent of holding the two parallel conferences is to allow for networking, to minimize future needless redundant effort. The opening session panel speakers represent expertise from both industries; I feel honored to speak as one with a history of serving both groups as a specialist in the subsurface behavior of heavy metals.

Jan 1, 1991