Search Documents

The declining grades of surface deposits have re-confirmed the need for greater production rates. Large scale production requires increased investments in expensive and sophisticated equipment. The key to successful operations can depend entirely on proper equipment utilisation and in this program of research at the Department of Mining and Metallurgical Engineering, University of Queensland, much emphasis has been placed on the analysis and improvement of this aspect of a load-haul-dump operation. For a model to be successfully integrated into a mine engineering function and readily accepted by mine operating personnel, it has to offer more than just results. The concepts used in its design and construction must include sufficient detail to enable engineers to apply it usefully and with confidence.

Jan 1, 1979

By Leszek W. Lunarzewski, Adam L. Lunarzewski, Raymond C. Pilcher

The Floorgas and Roofgas simulation programs are used to identify strata relaxation zones and their boundaries, to assess active gas sources from coal seams and gas¬bearing rocks and to determine relevant gassiness prediction coefficients for any local longwall. The paper shows that by use of the print-outs from the Floorgas and Roofgas programs the following benefits are achievable: • identification of the shear and gas discharge zone positions in the floor, strata relaxation angles and various gas discharge zone positions in the roof, which are both relevant to local geological and mining conditions • optimisation of cross-measure drainage hole length, location, number and angle of inclination calculation and definition of gas make prediction coefficients such as the release ratio from adjacent coal seams, specific gas emission during longwall extraction and the relationships between gas make, longwall width and coal production levels.

Jan 1, 1995

By Subash Chander, B. Arnold

Many developments have occurred in coal flotation with regard to increasing recovery from the flotation circuit and its impact on overall coal preparation plant recovery. This includes innovative design of flotation circuits, equipment modification and development, methods of enhancing the use of reagents, effect of slimes, and recognizing the effect of water chemistry. This paper will review recent advances and present some guidelines to improve process efficiency.

Jan 1, 2005

By J. G. Groppo, B. K. Parekh

Column flotation testing was conducted on the flotation feed slurry obtained from a preparation plant located in the Southern Illinois coal basin. The column flotation tests were conducted using three different bubble generating devices: a static sparger, a gas saver and a foam jet. Each of these devices was tested with three different types of frother and various column operating variables to provide maximum combustible recovery, minimum product ash and maximum pyrite rejection. The results show that column flotation provided improved flotation performance, in terms of combustible recovery as well as ash and pyrite rejection, for each of the bubble generating devices. However, the effectiveness of each bubble generating device was dependent on the type of frother used. Alcohol frothers were most effective for use with the static sparger, somewhat less effective for the foam jet and ineffective for the gas saver. Glycol frothers were effective for all three bubble generating systems, providing high combustible recovery (>90%); low clean-coal ash (4-6% ash) and high pyrite rejection (70-80%).

Jan 1, 1994

By James E. McTurk, Sheldon B. Bland, Roger E. Melley

During the first fifteen years of operation at the Syncrude facility in northern Alberta, numerous improvements have been made in the field of ore conveying. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about with the use of detailed field evaluation. This paper outlines some of the programs which have been run to optimise belt and system construction, and conveyor performance and utilization.

Jan 1, 1993

By P. Somasundaran, C. C. Harris

The power consumption of stirred-media mills was studied using an approach developed from work on stirred reactors. Evaluated were the relationships of factors such as stirring speed and impeller and tank dimensions on the torque required to rotate disc and pin impellers immersed in dense particulate media. Data collected under carious experimental conditions were analyzed. The results were summarized and presented in the form of characteristic plots, general equations and dimensionless group correlations involving power and modified Reynolds numbers. Special attention was directed towards the rheological properties of the media, which was considered a non-Newtonian liquid, and hence the equation of power-law liquids was employed. A procedure for estimating the parameters of effective viscosity and scale-up guidelines (with respect to power consumption) are proposed.

Jan 1, 1996

By A. Unal, R. L. Grayson

The use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments are reviewed, and the specifications of some of the past and currently available systems are presented. The advantages and disadvantages of using various frequencies, system configurations and specific components, including their construction standards and capability, are also discussed. The remaining challenges to the more widespread use of RFID systems for personnel and vehicle tracking are identified, and recommendations concerning the operating environment capabilities are detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency are discussed.

Jan 1, 1999

Development of process control in the metallurgical industry over the past ten years has been highly influenced by technical advances centered on use of computers as well as on measurement and associated equipment. The discussion in this section reviews advances in computer technology, measurement devices, data input-output techniques, and their use in mineral processing for the objective of guiding application of process control principles. Advances in the next ten-year period through the 1980's can be foreseen in the cost and application of data handling facilities in the coincident fields of data processing equipment, interface and control devices, and computer programming systems. These will lead to greater acceptance in a widely expanding range of mineral processing fields. It can be predicted that process control methods now known to be effective will become more re- fined. Costs of on-stream analyzers for assays and particle data will be reduced. Continued innovation can be anticipated in measurement devices required for effecting control. Control techniques developed over the last decade in key process operations such as crushing, grinding, flotation, smelting, and hydrometallurgical processes are described in the following chapters. The general forms taken by computer process control are first outlined briefly.

Jan 1, 1979

By Thomas E. McNider

Preliminary studies were conducted at Jim Walter Resources, Inc. Blue Creek No. 3 Mine to determine the influence propane operated heaters exert on the mine ventilation system when two of three intake airshafts were heated. During initial use of the heaters, it was found that change in density caused by heating a portion of the air at two of three intake shafts altered under- ground air flow changes sufficient to be considered a violation of Part 75.322 of the Federal Coal Mine Health and Safety Act of 1969 as amended by Public Law 95.164. The primary concern was to accurately define the problem in order to derive a workable solution.

Jan 1, 1980

By Jed H. (Original by) Mosgrove

Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 ma/s (9000 cfm) of air at his last open crosscut.

Jan 1, 1981

By Michael J. Martinson, John R. Larsen, J. Warren Andrews

Measurements reported in the paper were recorded in an active Green River, Wyoming, trona mine, partly as a teaching exercise and partly to provide the mine in question with additional input data for its ventilation network program. Measurements were made: - in representative three-entry intake airways in room and pillar sub-mains; - between the lower portion of a vertical down-cast hoisting shaft and the start of an intake airway system established in a room and pillar main; - in a representative downcast section of a divided vertical shaft, and of the collar entrance loss at the top of the same compartment. Pressure differences were measured with manometers and trailing hoses, air flowrates with calibrated anemometers, and barometric pressures and wet-and dry-bulb temperatures were recorded for density determinations. Where possible, results are quoted as Atkinson friction factors, and relevant measurements are recorded in some detail to show the magnitude of fluctuations in observed pressure differences.

Jan 1, 1987

By James S. Redpath

INTRODUCTION Background Early in 1972 our firm was asked by Cominco, managers of Arvik Mines Limited, to carry out an underground exploration programme referred to as the "Polaris Project" on a zinc-lead deposit in Canada's High Arctic. We had carried out numerous projects in the far north but this was to be the first long decline driven in perma-frost. Despite the short notice it was possible to meet the quickly approaching summer shipping deadline. We were able to do this by drawing heavily on our own and Cominco's background in Arctic operations. The project was an excellent example of owner-contractor co-operation and this spirit was responsible for the success of the project. Unusual Aspects There were a number of unusual aspects of the Polaris Project which are discussed in this paper. The extremely remote location, the short shipping season, and the fact that the work was carried out in permanently frozen ground, when combined with the lack of handy fresh water and a very severe climate, make it unique in many respects. Despite these handicaps, a record was set during the driving of the exploration decline.

Jan 1, 1974

By Robert J. Watters, Peter C. Kelsall, Joseph G. Franzone

Two separate studies investigated the compressive strength of basic igneous rocks and its relation to index properties such as porosity, density and soundrave velocity. The rocks tested were weathered dolerite from S. W. England and vesicular lavas from California. In both cases strength was affected considerably by porosity. In the dolerite, strength was also affected by fissures (microcracks) which were formed in the parent rock by shearing and later accentuated by weathering. While test results show that porosity, density and sound velocity are not reliable indices of rock strength, these properties are useful in interpretation of strength test results. Index testing can be used to classify samples according to similar behavior and to recognize the influence of fissures.

Jan 1, 1986

By D. D. Runnells, D. C. Keith, G. A. Doyle, J. Tilk

Until the suspension of conventional operations in 1996, the White Pine Mine was the second-largest active underground copper mine in the United States, underlying an area of approximately 30 km2 (13 sq. miles) in the Upper Peninsula of Michigan. The mine operator intends to initiate in-stope solution copper mining by circulating a solution (lixiviant) of mine water, sulfuric acid and ferric iron through rubblized ore. As planned, the solution would be retired in the mined-out stopes following completion of the solution-mining activities. Investigations into the fate of the retired solution indicated that the solution, through time, would change from an acidic, metal-rich solution to a near-neutral, reducing solution containing much lower concentrations of metals. Investigations included reaction-path modeling (EQ3/6) and laboratory and in-mine tests. The combination of neutralization and reduction will result in precipitation of most metals, primarily as metallic sulfates, chlorides and sulfides.

Jan 1, 1998

By M. T. Ityokurnbul, M. P. Trubelja

Concentrate flow rates were measured for the flotation of -100-mesh Lower Kittaning coal in a computer-controlled 0.076 x 3.5-m pilot flotation column. The variables studied were recovery zone height, airflow and solid feed rates. The specific projected surface areas of the feed, concentrate and tailing streams were determined from the measured particle size distributions. The results obtained show that the concen¬trate flow rate was independent of recovery zone height but was dependent on the hydrostatic pressure setting (measure of froth depth), gas flow rate, solid loading and particle size. New correlations for column carrying capacity and yield are provided as a function of bubble surface area flux and the specific particle projected surface area.

Jan 1, 1999

By E. H. Ahrens

This paper deals with the responsibilities of an operating geologists and the relationship of operations to exploration. It should be of interest to those soon to enter the profession, those new to pining geology and as a review to more experienced geologists. Subjects discussed include detailed geologic mapping, sampling, core logging, assaying, selection of proper map scale, posting geological and assay data, section preparation, identification of ore controls, delineation of development drill targets and geologic hazards, models and the very important topic of salesmanship. Methods and ideas, proven valid in vein, pyrometasomatic replacement and porphyry copper deposits are presented. Hopefully, these will smooth the path for new members of our profession.

Jan 1, 1992

By M. M. Veiga, M. Koehoorn

This paper reports on recently completed research that investigated the health fabric of mining communities in British Columbia (BC), Canada. The project, funded by two national funding agencies and the BC Government, and supported by numerous provincial organizations, marked a collaboration between mining engineering and health researchers. The study employed mixed-methods. First, a quantitative phase merged census, mining industry and health data to investigate the relationship between declining economic conditions and health outcomes (mental illness and stress-mediated cardiovascular disease). Second, a qualitative phase investigated community health issues associated with the mining boom-bust cycle from the perspective of health and social service providers working in a northern BC coal mining community. Third health research findings were disseminated to potential knowledge users in the hope of enhancing mine impact assessing and integrated mine planning. The paper provides a synthesis of the research methods used in this project, and highlights the main indicators used and key findings. It concludes by identifying recommendations, and future research needs considered to be of particular importance to the health and sustainability of mining communities in BC, Canada and around the globe.

Jan 1, 2011

By P. L. Webster, S. D. Thompson

Sevim and Wang (1988a) have presented a model for designing haulage systems in underground coal mines. The authors contend that their model uses a heuristic algorithm to optimize various haulage system parameters. In reality, it would be nearly impossible to optimize a haulage system, because mining plans are uncertain and often change with respect to time. Therefore, haulage system design poses both a stochastic and a dynamic design problem, and its optimization appears to be well beyond the scope of heuristic algorithms. In regard to the authors' design model and its practical significance, a number of additional issues warrant further discussion and clarification. These issues include: l) their model's alleged advantage over simulation models, 2) the correctness of their belt network design, 3) the correctness of their bunker design, 4) the necessity of their proposed bunker clearance policies, 5) the correctness of their shaft-bottom bin design, and 6) the

Jan 1, 1991

There has been some confusion over the selection of discount rates when performing stochastic simulations of a project's net present value (NPV) using risk- adjusted discounting techniques. Some argue that lower discount rates should be used when performing stochastic valuation simulations. This creates higher NPV values and improves the attractiveness of a project. Others argue that the discount rate should not be lowered for these simulations. This paper exposes the source of this confusion. It demonstrates that stochastic simulations do not remove the risk inherent in a project and, therefore-do not improve a project's value to the risk-averse investor. Risk-adjusted discount rates should, therefore, not be adjusted downward when performing stochastic NPV simulations. Stochastic simulations are, however, shown to he useful in several aspects of project valuation.

Jan 1, 1996

By Fred N. Kissell, Robert J. Timko

Safe escape from coal mine fires continues to be a concern of the mining industry. The most life-threatening fires occur outby the working sections. Because stoppings always leak some air, an outby fire may in time cause intake escapeways to become contaminated with smoke and toxic gases. Smoke and gas infiltration into intake escapeways can be minimized by raising their air pressure over that of adjacent airways. This can be done by checking off the intake escapeway near the working face. The Bureau of Mines has investigated the use of a parachute stopping as a quick-erect check curtain during mine fires, and the concept has been tested in several mines. In every instance, when a parachute stopping was erected on the section, the intake pressure went up substantially. The pressure-raising effect of the parachute persisted for up to 1200 m (4000 ft) outby. Results indicate that checking off the intake escapeway may serve as a viable way to improve safety during mine fires.

Jan 1, 1991