Search Documents

Refractory gold concentrates often contain sub-microscopic gold that is encapsulated within the crystal matrix of iron sulphide minerals such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically, by oxidative processes such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pre-treatment processes is usually the oxidation of the sulphides to elemental sulphur, sulphur dioxide gas or sulphate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as down stream operating costs. Iron sulphide minerals break down completely during pressure oxidation, and dissolve in the sulphuric acid solution that is generated from oxidation of the sulphides. This liberates the tiny gold particles that were originally trapped in the sulphide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulphate, but this is rapidly oxidized to ferric sulphate, which then hydrolyzes and re-precipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200OC) the formation of hematite is favoured. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200OC), the formation of basic iron sulphate is favoured. If the ore or the leach solution contain significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favoured. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulphate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulphates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulphate; the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant, and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

Refractory gold concentrates often contain submicroscopic gold that is encapsulated within the crystal matrix of iron sulfide minerals, such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically by oxidative processes, such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pretreatment processes is usually the oxidation of the sulfides to elemental sulfur, sulfur dioxide gas or sulfate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as downstream operating costs. Iron sulfide minerals break down completely during pressure oxidation, and dissolve in the sulfuric acid solution that is gener-ated from oxidation of the sulfides. This dissolution liberates the tiny gold particles that were originally trapped in the sulfide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulfate, but this compound is rapidly oxidized to ferric sulfate, which then hydrolyzes and reprecipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200°C), the formation of hematite is favored. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200°C), the formation of basic iron sulfate is favored. If the ore or the leach solution contains significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favored. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulfate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulfates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulfate: the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

By T. Veneroso

Comminution is the process by which rock or ore is reduced to a size where the liberation of the minerals is maximized without changing the chemical or physical properties of the rock. Comminution accounts for about 50% of all energy that mines use (Klein et al., 2018). Growing demands from stakeholders and shareholders for sustainable development and CO2 reduction will increase the need for energy-efficient comminution. Ores with different mineralogical characteristics, textures, strengths, apparent stiffness, and mass-specific fracture energies need to be processed with a specific, new, and efficient comminution technology to increase the production and profitability of mining companies. The adoption of crusher wear parts built with new materials, such as non-Hadfield manganese steel or synthetic materials or traditional manganese with wear-resistant components, could improve the efficiency of the crushers, reduce downtime, increase production, improve the desired P80 (the aperture through which 80% of the product will pass) product size distribution, and enhance mine safety.

Feb 1, 2023

By V. Rastogi

Acid rock drainage is the result of exposure of sulfidic materials, such as pyrites and sulfidic ores, to air and water. The oxidation of these sulfides is catalyzed by more than a million times by the bacteria Thiobacillus jerrooxidans and close families. Inhibition of these bacteria can mitigate 98% or more of the acid loading generated. This can be achieved by the use of certain surfactants that are selectively bactericidal to the lithotropic acidophilic bacteria. Bactericides are used in two ways. As periodic or continuous treatments for prevention of acidification of material actively handled and moved, and in controlled release form for reclamation where treatment sets up a change in site microbiology to replace Thiobacillus jerrooxidans with heterotrophic bacteria and creates a stable site without need for further treatments. Use of bactericides begins with laboratory testing of the site material to qualify the site for bactericide treatment and dosage determination. Site specific treatments are designed for active sites and reclamation. Once acid production is controlled, solubilization of metals is correspondingly reduced. Results and economics of use from active and reclamation sites are presented.

Jan 1, 1995

By M. Akram

Stability assessment of entry roofs is an essential precursor to all underground design. Both multi-seam interaction and longwall mining can subject entries to radical changes in the surrounding stress field. Such loading changes frequently produce instability and failure in the roof, floor and pillars. Roofs are shown to be vulnerable to stress-induced failures, particularly when the load is unsymmetrical. To predict the effects of changes in stress field, roof failure conditions under increasing loads were studied using finite element analysis and body loaded photoelastic models. A large range of geologic conditions were evaluated and incorporated into the model using Monte Carlo methods. Entry analysis using the model showed the roof to be particularly vulnerable to shear with the location of the failure site changing to meet loading and geologic conditions. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Based on this research a roof stability model SESAME was constructed for roof stability evaluation under specified loading conditions.

Jan 1, 1993

By Stanley Noss

One need be neither an historian nor technologist to recognize that activi¬ties related to the conversion of coal to other usable energy forms have been active for nearly fifty years. The degree of such activity and its evolution to significant commercial proportions has, however, fluctuated widely with world circumstance. For the past decade there has existed both a consistent technology evolution effort in classic R & D proportions, and a mainstream commercial acti¬vity but in rather modest proportions when viewed from the vantage point of world energy needs. But the chain of events wherein it became increasingly obvious that we were in energy trouble irrespective of world politics, spurred alternative energy source activities in the fossil fuels areas. The oil embargo of 1973-1974 made the obvious even more so and provided additional emphasis for the need of such alternatives. Yet the preponderance of these added expenditures and activities (with one notable exception which is the subject of this discussion) has been focused on the intended identification of the best or ultimate process by means of analytical and modest empirical means, whereas our circumstance dictates a bold, higher-risk effort to prove the viability of coal conversion as an industry on a real-time, real-size, real-economics basis. With such proof on hand, industry demands in all related areas will provide the stimulus, motivation and environment for all processes. There is both need and room for many who will compete for a meaningful segment of this new industry which can grow at a rate never seen before in our growth history. The single program in the world today oriented specifically toward the goal of proof of industry viability is the Energy Research and Development Administration&apos;s CBF (clean boiler fuels) Program for which COALCON is proud to be the prime contractor.

Jan 1, 1976

By Enrico Pavese, Tim Kearney, Stefan Lemke

Watertightness is of central importance in hydraulic and underground structures but has always been associated with a risk, as demonstrated by the very high impact that water inflows have on the damage of linings and infrastructure (Howard, 1991; Sandrone and Labiouse, 2011). Concrete is vulnerable to groundwater and chemical contaminants in the soil. These can leach into the pores and cracks of the concrete and degrade its integrity, causing spalling and corroding the reinforcing steel. Moisture migrating into the building can also degrade structural elements over time and lead to mold and other hazards to occupants’ health. In this connection, the demands placed on the setup and detailed design of the seal depending on the negative influence by water on the one hand and on the other hand on the function of a construction in view to its watertightness classification. Thus, the reliable functioning of a seal is of particular significance in the case of traffic tunnels, which are not easily accessible for all subsequent repairs after the construction in seepage water and especially when located in a pressure water zone (risk–cost assessment). Requirements for the long-term efficiency and quality of underground structures have increased in recent decades. Today, the standard lifetime requirement for an underground infrastructure project is 100 to 120 years and, in some cases, even higher. This calls for high increased attention to the durability of the whole structure and of each individual element. Standards, which started as application guidelines given by the manufacturers, are available in the market since the 1980s and are constantly adapted to the current developments in various technical committees. Differentiations are made between: Manufactures application guidelines, case studies or published articles Test standards for the laboratory to guideline the testing procedures (air temperature, type of test equipment, dimensions, test speed, test duration, concentration, type of liquids, monitoring, tolerances, interpretation of results, documentation, etc.), developed by committees based on material and laboratory experts Application standards, which include test standards but also the related minimum performance requirements (values) for material, processing, and quality assurance (practical tolerances), developed by committees based on a wide range of experts (e.g., designers, construction companies, applicators, manufactures, owners, test institutes, quality engineers) and therefore also based on a wide field of experience, different views and up-dated case studies. In the following there are some examples of guidelines and published information’s, ranked according to the year of issue, which are relevant for the development of waterproofing specifications in the tunnel industry:

Jun 13, 2023

By Laszlo Valentyik

Heavy media separation (HMS) is one of the most widely used gravity methods in the mineral industry. The feed is separated, according to the specific gravities, into two products; float (light) and sink (heavy) particles. The universal acceptance of the process is due to simplicity, efficiency and robustness for ease of control. However, if optimum separation is desired during the operation of heavy media plants, a delicate balance of a number of variables is essential. Among the variables, the two which are generally the most frequently checked and controlled are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media. The medium is generally made up of finely ground ferrosilicon, magnetite, galena, shale, quartz sand, clay contaminants and water. The frequently present clay in the medium acts as a stabilizing agent, since the coarse heavy medium solids (called media) would quickly settle if they were mixed only in water. Clay concentration of the medium varies between 3-7% by height (1,2). Although clay is essential for reasonable media stability, clay concentration greater than 7-8% imparts too high a viscosity to the medium, and the feed cannot accurately stratify and therefore separate into the required products. To be on the safe side, plant operators clean the medium from most of the clays, and would rather work at a lower stability than have a very viscous medium on their hands. The most recent advance in the area of consistency control rlas made by the introduction of atomized (spherical) ferrosilicon (3). This extended the upper limit of the use of ground ferrosilicon from 3.3 to approximately 3.6, broadening the range of the optimum operating conditions. A viscosity control method was also worked out by the use of low cost additives which lower viscosity while retaining a favorable low setting rate (4). Recently (5) polymers have been successfully used in oil well drilling muds then the requirements were mainly to suspend and transport cuttings during the periodic shutdowns and dril1ings respectively. The rheological properties of these polymer suspensions are such that they present an infinite viscosity to

Jan 1, 1971

By R. Aliberti, E. Comis, M. Wone

DC Water’s Clean Rivers (DCCR) program involves the construction of approximately 29 km (18 mi) of CSO tunnels in Potomac Group soils in the Washington DC area. Soils include an upper predominantly over-consolidated fine grained plastic material facies (P/A) and lower predominantly coarsegrained facies (PTX). As earth pressure balance (EPB) tunnel boring machines (TBMs) are mainly used in such soils, the correct approach to soil conditioning can make a considerable difference in TBM performance. Soil conditioning laboratory tests are often completed during the planning phase prior to TBM excavation to develop a baseline for soil conditioning, reduce risks, minimize costs, and improve performance. However, only a few basic tests are standardized to date, and conditioning regimes are fine-tuned during the mining phase. The paper illustrates the effort carried out to identify the correct soil conditioning regime for both PA and PTX facies to improve TBM overall performance and reduce ground movement during the excavation of the Northeast Boundary Tunnel (NEBT) in Washington DC.

Dec 1, 2022

By C. Beul, R. Schipper, L. Santisteban

The Garfield Mine is a legacy vanadium mine in western Colorado with multiple mine openings, waste rock piles, and adit seepages that Cyprus Climax Metals Company (a Freeport-McMoRan Inc. subsidiary) voluntarily remediated through the Colorado Voluntary Cleanup Program (VCUP). The process to obtain a No Further Action determination from the VCUP is presented. Water treatment of the adit discharge, which is not part of the VCUP, is also presented. The remedial action objectives (RAOs) included preventing direct human or biotic exposure to the waste rock and radiation emitting from the waste rock; reducing metal concentrations and radionuclide activities in adit discharge and keeping the discharge from leaving the site; maintaining the existing undeveloped character of the surrounding landscape; and eliminating the need for a stormwater permit. The design included regrading, installation of an infiltration barrier and rock cover, a diversion channel, and a biologically based passive remediation water treatment system. An initial lab-scale evaluation provided design criteria for the full-scale system, which consists of a sulfate-reducing biochemical reactor and post-treatment aerobic polishing cells. The system has been operational since construction was completed in late 2016. Results indicate that the treatment objective of 90% bulk removal of constituents of potential concern (COPCs) is largely being met. The system also provides year-round operation and non-point discharge of effluent. After 20 plus years of site investigations, the remedial action was completed in 2016 with all RAOs met and a No Further Action determination granted in 2018. INTRODUCTION The Garfield Mine is a legacy vanadium mine located approximately 11 miles north-northeast of Rifle, in Garfield County, Colorado. It was leased and operated intermittently from 1929 to 1975 but was never operated by Cyprus Climax Metals Company (Cyprus) (a Freeport-McMoRan Inc. subsidiary). Prior to reclamation, site features included: • six mine openings—five adits and a vertical opening; • two adits discharging mining-influenced water (MIW)— Adit 1 at less than 4 liters per minute (L/min) and Adit 2 at 7 to 10 L/min; • main waste rock pile (13,500 m3) and small waste rock pile (minimal volume); • debris (small structure, mattress, bottles, shells, etc.) indicating site used for recreational purposes; and, • unimproved road, which has been used to access forest fires.

Jan 1, 2019

A viable mineral economy requires availability of economic deposits, the ability to exploit then, and protection of the public interests. The natural tendency for each party to consider only its legitimate self interests can lead to delays or deadlocks. The paper presents several viewpoints aimed at opening each party&apos;s mind to the ideas of others in the hope that negotiations might be more reasonable and rapid for the benefit of all concerned.

Jan 1, 1979

By R. J. Sweigard

Many states are considering the need to establish or modify policy relating to the disposal of coal ash. One of the primary concerns is the impact of leachate from the ash disposal sites upon groundwater and nearby bodies of surface water. A detailed site investigation was conducted at a coal ash disposal facility associated with a power generation station. The disposal site is situated alongside a major river. Monitoring wells were installed and soil samples were taken for characterization. Groundwater models were used to simulate migration of leachate from the disposal site toward the river. Such models could be used potentially to verify regulatory compliance. This paper addresses the validation and adaptability of these models to this case and their usefulness as possible tools to be used in future environmental audits.

Jan 1, 1992

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984

By R. Mensah-Biney

The kinetics of loading of gold from bromide solution onto an anion exchange resin, PAZ-4, were investigated in a batch stirred reactor. The initial loading rate was described mathematically by a first-order reaction rate equation. The effect of agitation speed, temperature, resin particle size, resin concentration, initial concentration of gold and bromine in solution on the rate was investigated. The model described fairly accurately the loading process in terms of the variables investigated. The rate constant for the initial loading ranged from 0.5 to 1.3 x10-3 sec-1 and the half-time was 9.3 to 56 minutes. The initial rate constant increased with increasing temperature with an activation energy of 15.7 kJ/mole (3.8 kcal/mole). The rate constant was directly proportional to the concentration of the resin in solution. The subsequent reduction reaction was also modeled by the first-order rate equation and the apparent rate constant was estimated to be 3.0 x 10-6 sec-1 with a half-time of about 44 hours.

Jan 1, 1994

By S. K. Kawatra

The use of inferential particle sizing for a closed wet grinding circuit control has been practiced for several years. This paper presents a review of some inferential sizing equations developed for pilot and industrial plants using regression analysis. An analytical development is then presented showing how the general inferential sizing model arises from the nature of the classifier model. The relation between the general sizing model and the individual equations is then discussed.

Jan 1, 1982

By R. T. Richins

Coeur d&apos;Alene Mines Corporation (CDE) is a precious metals mining company. The company&apos;s three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE&apos;s gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By D. W. Alexander

In 1993, CONSOL began investigating new methods of permanently filling coal mine shafts, which after ventilation is stopped, may contain a potentially hazardous atmosphere. Fill materials such as fly ash/cement can be pumped, are non-combustible and non-incendiary but tend to flow into the mine entries. A non-flowable mixture has been developed that minimizes the volume of fill used. The paper presents our recent shaft filling experience including fly ash material properties, mix designs, field problems, placement success, and gas testing techniques.

Jan 1, 1996

By James E. Lawver

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent or at least delay mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the forms of calcined bones at least 2 000 years ago, (1) and man has used phosphate minerals as a source of fertilizers in one form or another for at least 100 years. During 1977 the world produced about 116 million metric tons of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows. Marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits, requiring an apatite carbonate mineral separation.

Jan 1, 1978

By J. Casado

This paper presents the results of an analysis and summary of relevant literature on the mechanism of cementation of metals in acidic aqueous media, with the aim of reconsidering the conventional assumptions. The simplicity of the process as a mere galvanic metal displacement is discussed, and the real effects of pH and hydrogen pressure in different cases assessed. Finally, an alternative mechanism scheme with respect to the role of hydrogen species, in agreement with reported data, is proposed.