Search Documents

By W. C. Smith

Even with conservative mine planning, rib instability can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation. sporadic zones of progressive rib instability were detected that culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1991

By Lawrence D. Ramspott

A test of retrievable geologic storage of spent fuel assemblies from an operating commercial nuclear reactor is underway at the Nevada Test Site (NTS) of the U.S. Department of Energy his generic test is located 420 m below the surface in the Climax granitic stock. Eleven canisters of spent fuel approximately 2.5 years out of reactor core (about 1.6 kW/canister thermal output) were emplaced in a storage drift along with 6 electrical simulator canisters. Two adjacent drifts contain electrical heaters, which are operated to simulate within the test array the thermal field of a large repository. Fuel was loaded during April-May 1980 and initial results of the test will be presented.

Jan 1, 1981

By Kenneth A. Pietila

The thickening and dewatering characteristics of refuse slurries are as variable as the coal mining operations and preparation plants that create them. This paper discusses these characteristics based on field studies at a number of mine sites. The connection between bench and full scale performance is confirmed with the design, construction and operation of an integrated 18m (60 ft) diameter thickener and 2.5 meter belt filter press system in Western Kentucky. The data from this system are presented.

Jan 1, 1984

By B. T. Field

Pyroprocessing systems range from low temperature dryers to high temperature reactors. The materials and process requirements cover a broad spectrum. It is not the intent of this paper to do a detailed examination of individual processes and equipment, since that can be found in a multitude of other sources; rather it is the intent of this paper to examine the key process variables and offer empirical guidelines to assist in a user?s overall evaluation.

Jan 1, 1998

By Fumio Wada

Kuroko deposit is a stratabound massive sulphide and sulphate deposit associated with Miocene submarine volcanics and has been considered to be a prototype of meta- morphosed Palaeozoic and Precambrian equivalents. Since the discovery of Uchinotai deposit of the Kosaka mine in 1959, Dowa and other mining companies have conducted intensive exploration work in the Hokuroku district of northeastern Japan. Dowa has been placing its first priority on the exploration of Kuroko deposits and made a series of remarkable successes in finding the Kuroko deposits, i.e. Uchinotai, 1959; Matsumine, 1963; Uwamiki, 1966; Fukazawa, 1969 and Ezuri, 1975. It is emphasized that our successes have resulted from the proper application of exploration technologies accumulated through our experiences. Firstly we defined the Kuroko horizon and favourable felsic volcanism based on the detailed structural and volczno-stratigraphic study of the Hokuroku district, and then delineated the promising areas by means of the quantitative evaluation of geophysical, geochemical and mineralogical parameters such as the magnetic susceptibility and contents of alkaline and alkaline earth metals in the foot wall dacites and clay mineral assemblages of both hanging and foot wall pyroclastics and dacites. Practical application of these techniques is essential to our routine Kuroko exploration.

Jan 1, 1982

By S. Mohanan, C. R. Kumar, S. K. Bhoja, T. Venugopalan

"A pressing issue that has often been the topic of discussion in iron-making operations in India is the high content of alumina in the country’s iron ore deposits. The presence of alumina has hampered production by affecting slag fluidity, and thereby the hot metal quality. Iron ores from Indian mines are generally rich in hematite, with traces or small amounts of goethite/limonite, kaolinite, gibbsite and quartz reported from time to time. In day-to-day production, emphasis is placed on checking the chemical analysis of product samples, but the true solution to the alumina problem lies in estimating the mineralogy of the ore samples. We developed a mathematical model, based on singular value decomposition, to predict mineralogy from classical chemical analysis. We then used X-ray diffraction patterns, scanning electron microscope analysis, and grain counting with an optical microscope to determine actual mineral compositions and to test the values predicted by the model. The results indicate that with regular calibration, the model can be used as a simple, fast and effective tool to predict on a regular basis the mineralogy of multiple samples.IntroductionIndian blast furnaces use high-grade iron ores (as lumps or as sinter) and coke (obtained from the destructive distillation of coal) as raw materials for the production of high-quality hot metal to be converted into different steel products through the Linz- Donawitz process. The iron ores are mainly sourced from the Singhbhum region of Odisha and Jharkhand states, the Bailadialla region of Chattisgarh state and the Bellary region of Karnataka and Goa states, and are mainly classified based on size as (1) lump ore (fed directly into blast furnaces), (2) fines (converted into sinter/pellets and fed to blast furnaces) and (3) slimes (< 0.15 mm; currently dumped in huge slime ponds). Any variation in the quality of the ores supplied results in variations in the production trends of hot metal."

Jan 1, 2015

By H. V. Scotland III

Lafarge Corporation&apos;s Texas Quarry, in Baltimore MD, achieved a substantial expansion of pit reserves by removing an inactive underground mine. The day lighting program, designed, and completed in 1997, open pit mined more than 400 meters of room and pillar workings which were originally developed to recover high brightness Calcium Carbonate. The project proved to be a challenge throughout its course as the pit plan was modified and successful daylighting techniques were developed to remove the mine without adversely affecting the safety of the operation, quality of the stone recovered, or negatively impacting the surrounding community. The design parameters and techniques developed and implemented at Texas may prove of interest to other operators as they are faced with daylighting opportunities. This article will detail the challenges we faced and the solutions which made the project a success.

Jan 1, 1999

By Boyd Eisenbraun, Dennis Murr, Milton Rojas

Approximately since 1925, the phenomena of grinding and classification of minerals with screens have been studied. In the U.S. iron ore mining operations located in the so-called “Mesabi Iron range,” magnetite processing plants have made progress in the application of high-frequency screens that have allowed them to process low-grade Taconite ores and successfully achieve the economic benefit of these minerals. In the particular case of magnetite minerals disseminated in the siliceous matrix, the main objective is to reduce the generation of particles called “middlings” with high silica contents. Commonly the primary challenge of the metallurgical task is to achieve high recoveries and iron concentrates with low impurities. To achieve this, several studies and industrial applications have shown success in this regard and not only in iron ores, but also in other minerals around the world. The study described in this paper attempts to describe some key aspects that helped develop an effective solution and list the benefits associated with this modern process design by using industry-proven technologies for minerals in Chile that have similar characteristics to the minerals of the iron belt in the United States.

Feb 1, 2025

By John S. Cummings

Although there are many geologic situations which might be discussed at a session such as this, as I considered the problem, it became apparent to me that I should discuss a situation which has been of concern to me, and should be of concern to the geologic community. As a result, the questions which I will pose, and the criticisms, have not been arrived at quickly or easily, but have accumulated through time, to the point where I feel discussion is necessary. Very briefly let me say that my criticism of geologic mapping, of conclusions reached, and objectives or lack of such, results from my association with many areas where such studies have been completed, and resultingly my inability to comprehend the system of evidence or logic which supports extensive age-formational designations. The heart of the problem is that many conclusions resulting in geologic designations are based on weak or non-existent evidence, and such should be catagorized as hypotheses. Although the geologic community as a group does not approve or disapprove of such designations, it is evident that many or most of such designations attain a "status", and arc accepted as more or less valid statements. As will be shown, the amount of specific lithologic data provided in some quadrangle mapping projects is exceedingly slim. However, of concern herein is that the type of information presented at any stage is sufficient to warrant conclusions drawn. To see the magnitude of the problem, it is probably necessary to review some basic fundamentals upon which our geologic systems are established. The United States Geological Survey has defined a "formation" as the broad unit of geologic mapping consisting of a large and persistent stratum of one kind of rock. Obviously such a designation allows that a formation could be considered "time variant" in a horizontal as well as in a vertical context. However, other definitions enable a formation to mean units

Jan 1, 1972

By W. D. Delahaut

Sampling tests performed at the Paradise Peak Mine compared various blasthole samplers and reverse circulation sampling methods. Statistical analysis of the data indicates that be-low-the-deck bag sampling produced a 24 to 29 percent error when compared to bulk sampling methods. Use of a chip pile wedge sampler reduced error to 17 percent. Reverse circulation sampling upgraded over bulk blasthole sampling by 7 percent for gold and 11 percent for silver. These results indicate that bias sampling conditions exist when small volume bag sampling is employed in production blasthole drilling.

Jan 1, 1991

By Keith Jones, Martin Knights, Timothy Watson

In 1996 a KBR (Brown and Root) led international JV was appointed to design and supervise an underground and surface package. The design of 6 km of tunnels, plus enlargements, deep shafts in glacial and sandstone deposits for the conversion of the existing LEP underground laboratory at CERN, Geneva adjacent to the Jura Mountains/Lake Geneva had to be undertaken in an operational environment and in conjunction with other underground constructions associated with the US$3bn refurbishment.

Jan 1, 2003

By J. A. Organiscak

This paper describes the research con-ducted on bit wear and respirable dust generation conducted by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy, and dust of one conical bit type when cutting coal. The objective of the USBM study was to identify qualitative bit selection guidelines for cut-ting rock; WVU&apos;s research objective was to determine optimum bit replacement guidelines. These research studies both found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1995

By John E. Anderson, Charles A. III Cravotta, Eleanora I. Robbins, E. Terrance Slonecker, Gordon L. Nord

Remote sensing is being tested for its ability to identify the severity of impact on streams that are subjected to contaminated mine drainage (CMD) in the Southern Anthracite Coalfield of Pennsylvania. Airborne digital multispectral video images of acidic and near-neutral CMD are being compared with field spectra, water chemistry, mineralogy, and microbiology. Spectral differences in the visible region of the electromagnetic spectrum are caused by the presence of schwertmannite in the acidic precipitates and ferrihydrite in the near- neutral precipitates. The acidic CMD averages 1,500 mg/L sulfate and has bacteria coated with schwertmannite; the near-neutral CMD averages 87 mg/L sulfate and has bacteria coated with ferrihydrite.

Jan 1, 2000

By Sakir Selcuk, Brian Hamilton, Paul Zick

The 1.8 mi (2.9 km) Minneapolis-St. Paul International Airport Light Rail Transit Tunnels and Station project is comprised of the underground segments of the 11.8 mi(18.8 km) Hiawatha Light Rail Transit route in Minneapolis, Minnesota. The 21 ft 2 in(6.5 m) diameter twin tunnels were mined 65 ft beneath one of the busiest airports in the United States using an earth pressure balanced tunnel-boring machine. This paper will provide a project overview, review the major equipment selected, tunnel segment casting, and describe excavation and lining operations for the tunnels and station.

Jan 1, 2003

By Paul A. Rittenhouse

First of all, I want to thank John Dunlap for asking me to this AIME meeting in Denver. I was first introduced to Denver and The Rocky Mountains more than ten years ago and immediately decided it was one of the most attractive spots in the world. I&apos;ve come back many times since and still welcome any opportunity to return, even if it means I have to prepare and give a paper on potash. When John Dunlap gave me this assignment, he told me that the program would include papers on the geology of potash, papers on new discovered potash deposits and new mines and asked me to discuss potash from the commercial point of view. He also asked me to include a supply/demand outlook for potash. However, one thing he did not mention was "how far into the future he wanted me to look" and it seems to me the time element is a crucial factor to you who are both geologists and miners as well as to me. In your case, you have to look far enough into the future to give you time to explore, find, evaluate, develop, and bring into production a commercial deposit. My mining associates and friends don&apos;t agree on how long that takes but it&apos;s probably somewhere in the range of eight to fifteen years. But, they all agree on one thing and that is that the time required is continually getting longer. Now my time problem is just the opposite. It is "relatively" easy, and I stress relatively, to identify and evaluate the importance of the various factors that impact on both the supply of and demand for a commodity such as potash if the time period is today. It gets a little tough if one has to project into tomorrow or next week or next month. And when we start talking in terms of a year, five years or ten or fifteen years, things really get sticky and the old crystal ball becomes mighty cloudy. But we economists and forecasters are not known for our temerity so let me get on with the job at hand and take a look at the world potash supply/demand outlook.

Jan 1, 1978

By J. Castaneda, J. Schmidt

"INTRODUCTION Chino is an open-pit copper mining complex faced with intricate material routing requirements. Historically, this was challenging at the mine, in part because the shovel dig plan, haul plan, and dump plan were prepared completely separately. The mine now uses an integrated workflow for faster evaluation of schedules, which facilitates preparing balanced cutoff grade-to-equipment requirements, supports better mineral production, and improves schedule viability, while considering operational implications. Located in the state of New Mexico, Chino is one of nine Freeport-McMoRan mining operations in North America. This presentation discusses the benefits of implementing an integrated approach to tactical mine planning, and shares practical examples that were learned as Chino implemented an integrated tactical planning method. This includes improvements in completion time for preparing a schedule, minimal risk from manipulating Excel macros, data integration required to make short-term planning decisions, and better understanding of the mine plan’s effect in relation to the business’s key performance indicators. Ultimately, the integrated approach to tactical mine planning at Chino has led to production forecasts which are more achievable and reduced planning and execution variance. PROJECT OVERVIEW Chino mine is a porphyry copper deposit wholly owned by Freeport-McMoRan, the largest publicly traded copper producer in the world. Chino mine is located in Grant County, New Mexico, a short distance east of Silver City. Ore material mined from the pit today includes oxides, primary sulfides, and secondary sulfides. The mineralized material is sent to a mill, with a rated throughput of 42,000 tons per day, or to ROM leach pads with variable dumping capacities. At Chino, the short-range objective is to maximize total copper pounds sent to the mill, but no fixed cutoff grade accomplishes this for all periods. Instead, 12 different material classifications, including four sulfide classes that can feed either the mill or other destinations, and 38 cutoff bins, are aligned with the needs from operations, leaching, and the concentrator to create a schedule. Cutoffs vary from one week to another to cope with a highly intermittent ore body."

Jan 1, 2018

By Peter G. Chamberlain

Domestic mining will not produce a significant portion of the manganese consumed in the United States unless new mining and processing techniques are implemented that will enable domestic lean ores to economically compete with rich foreign ores. One mining-processing technique that appears promising for certain deposits is in situ and/or heap leaching with aqueous SO2. Since leaching offers economic advantages of low capital costs, low operating costs, and short start-up times as well as environmental and safety improvements over conventional mining-processing, the Bureau of Mines studied the leachability of manganese deposits from several districts. Manganese oxides, hydroxides, and carbonates were leached to 80 to 90 pct recovery in 7 to 40 days of leaching with a solution containing 5 pct SO2 in column leaching tests. Preliminary cost analyses of surface mining-heap leaching, block caving-in situ leaching, and shrinkage stoping-in situ leaching indicate that the products of manganese leaching may be economically produced for the chemical and electrolytic manganese industries. The easiest marketable product to obtain would be a manganese sulfate commonly used as a fertilizer amendment. Manganese carbonates and hydroxides could also be precipitated from the pregnant leach solutions.

Jan 1, 1983

By G. Blackwell

In the 1980&apos;s the Canadian surface mining industry was confronted by declining competitiveness in the face of low cost foreign producers and alternative materials. Low metal prices undermined profits for many mining companies. Restructuring, rationalization, capacity reduction, technology transfer, as well as favourable currency rates and higher commodity prices, helped revitalize the industry by the close of the decade. Now in the 1990&apos;s, however, the need to improve competitiveness for profitability has re-emerged in greater intensity. In the current climate it is considered that there are three strategies available to industry to ensure profitability: continued rationalization and restructuring; optimization of operating practice; and technology development and transfer.

Jan 1, 1993

By K. L. Gabby

Selective removal of mercury from cyanide leaching solutions while retaining silver has been a long-standing problem, due to the chemical similarity of mercury and silver. In order to be practical, a mercury removal process needs to be both highly selective and use inexpensive materials. This paper reports the use of zinc sulfide (ZnS) as a precipitant for mercury. The mercury cyanide complex (Hg(CN)4 2-) undergoes a replacement reaction with the zinc sulfide, forming insoluble HgS, while the silver cyanide complex (Ag(CN)2 -) remains in solution. Under appropriate conditions, the separation of mercury from silver is nearly quantitative, with close to 100% removal of mercury, while nearly none of the silver is precipitated.

By B. Waterman, R. Collins, V. R. K. Paruchuri, P. Gonzalez, H. Dijkman

"INTRODUCTION Mining and processing of sulfide ore bodies has the potential to solubilize sulfate. Gypsum in the host rock, as well as oxidation of sulfides during milling and processing can solubilize sulfate. Acid rock drainage (ARD) also has the potential to generate waters high in sulfate. Even after treatment of the ARD with lime, the treated water can have sulfate present in gypsum saturation levels. Most mine-sites reuse sulfate impacted water but as a mine nears closure, reuse options may be limited and water treatment becomes an option. Furthermore, sulfate discharge requirements, particularly for anti-degredation narrative standards, can be very strict. Freeport has investigated many new technologies to economically remove sulfate from these types of water. A Dutch company, Paques B.V. developed one of these technologies and it utilized biological reactors to convert sulfate into elemental sulfur in a 2-step process. In 1992 the first industrial reference of the SULFATEQTM technology was commissioned at the Nystar Budel zinc refinery in the Netherlands. PILOT PLANT TECHNOLOGY AND DESCRIPTION As shown in Figure 1, the plant contains several process steps, which can mainly be divided into the following sections: 1. Anaerobic biological system in which sulfate is reduced to hydrogen sulfide by sulfate reducing bacteria. 2. Aerobic biological system in which hydrogen sulfide is oxidized to elemental sulfur by sulfide oxidizing bacteria. 3. Solid/liquid separation in which sulfur, calcium carbonate and biomass solids are separated and dewatered. Sulfate impacted ground water is pumped to the feed water tank through a plate and frame heat exchanger to maintain the solution temperature around 95°F. A custom mix of micronutrients is dosed to the feed tank. This nutrient mixture provides essential elements for the growth of anaerobic and aerobic biomass. Urea is added to the feed tank and provides the required nitrogen source to the biomasses. The pretreated feed water is pumped into the anaerobic reactor. The reactor works on the gas lift principle. Sulfate reducing bacteria utilize hydrogen gas as electron donors and reduce sulfate to hydrogen sulfide. This reaction increases the alkalinity of the solution. Carbon dioxide gas is added in order to control the pH within working range of the reactor. Due to the low solubility of the hydrogen gas, the anaerobic gas mixture is recycled through the system. The gas mixture recycle also provides the gas lift for mixing within the anaerobic reactor."

Jan 1, 2016