Search Documents

This United States Bureau of Mines study is based on a review of U.S. mine fire accidents that occurred from 1970 through 1989. Information on these accidents was obtained through investigative reports written by Mine Safety and Health Administration personnel. For this study, 260 mine fire accident reports were examined. A previous Bureau research effort established that fires causing fatalities were more likely to occur in haulage entries than at any other underground location. This study has found that the most prolific source of haulage entry fires was the inadvertent grounding of trolley wires. The largest segment (15 out of 40 trolley wire fires) resulted from not maintaining adequate clearance between the trolley wire and the vehicle. Several novel fire prevention and control ideas have evolved in response to frequently occurring fire-related problems. These included; discriminating power isolation devices, wire cutting devices, more accessible fire extinguishers, vehicle overcurrent protection, and vehicle fire suppression.

Jan 1, 1994

By J. T. Carlson

Dolomite is an objectionable impurity in phosphate ores, due to its MgO content. Even though dolomite and apatite liberate at a coarse size, the very similar densities of dolomite and apatite makes density separations difficult. However, if operated correctly, jigging can be a very efficient process. This has led to the development of a unique laboratory scale jig that allows for easy alteration of effective jigging properties. Key jigging parameters have been investigated for the separation of dolomite from phosphate ores. It was found that a pulsation rate of approximately 200 pulses/minute worked best for separating dolomite from apatite.

Jan 1, 2010

By E. Topuz, C. Patrick

Longwall face-to-face equipment transfers or moves are the largest source of nonproductive time in a long wall-mining system. Detailed planning and resourceful thinking are paramount for economical, safe and timely longwall moves. New equipment and innovative techniques are frequently tested to reduce overall more time. Determining the cost-effectiveness of these ideas is difficult since the decision is influenced by many subjective factors. A project scheduling simulation model of the longwall move process was developed to analyze and assess the economic viability of innovative transfer methods and equipment. The model provides a project-duration frequency distribution and lists of critically indexed activities and paths. It compares the monetary savings from reduced transfer time and capital costs for several ideas.

Jan 1, 1996

By William Gleason

"Komatsu has been on the cutting edge of autonomous mining for the past 30 years and the company remains at the forefront of the technology that is changing from concept to a full-fledged reality.In 1996, Komatsu America Corp. (KAC) purchased a controlling interest in Modular Mining Systems; a move that enabled both companies to expand their product lines. It was through this effort that Modular helped to deploy the first autonomous haulage system (AHS) — the Komatsu FrontRunner system. In January 2008, the first commercial implementation of the FrontRunner system occurred at Codelco’s copper mine in Chile. Since then, Komatsu has put more than 130 haul trucks into seven sites on three continents to haul copper, iron ore and oil sands and its equipment has moved 1.8 Gt (2 billion st) of material with zero lost time incidents attributed to Komatsu’s autonomous trucks. The 1.8 Gt (2 billion st) is the most of any commercial mining autonomous haulage system and there is more to come. In November, Komatsu announced that an additional 150 autonomous haul trucks will be deployed to the Canadian oil sands over the next seven years.Komatsu has continued to pioneer autonomous haulage development, creating a range of autonomous options that includes semiautonomous and teleremote options all the way up to a haulage vehicle that stole the show at the world’s largest mining equipment trade show.In 2016, Komatsu advanced the concept of driverless haul truck to a new level when it displayed its Innovative Autonomous Haulage Vehicle (IAHV) at MINExpo in Las Vegas, NV. The concept vehicle is the first mega class haul truck designed to be fully autonomous, without an operators’ cab included on the vehicle.Unlike other haul trucks, the vehicle was developed exclusively as an unmanned vehicle designed to maximize the advantages of unmanned operation. Among other advancements, it was designed to distribute equal load to the four wheels, both when the vehicle is loaded and unloaded, and adopt four-wheel drive, retarder and steering. Komatsu said it is aiming for high-performance shuttling of this vehicle in both forward and reverse travel directions, thereby eliminating the need for K-turns at loading and unloading sites."

Dec 1, 2018

By Samuel Polinsky, Lawrence W. Bierman, Wayne Perkins

[A column float beneficiation plant using 9, 8.5 foot diameter, cells was constructed by the Simplot Company and the Smoky Canyon Facility in the fall of 1986 and has been in operation since May of 1987. The float beneficiation process was developed jointly by the Simplot Company and the Bureau of Mines (Salt Lake City, Utah) which incorporates the Bureau's bubble generator design and chemistry system based around the reverse float technology, (Albany Bureau of Mines, Application of Carbonate-Silica Flotation Techniques to Western Phosphate Materials, Rule, Dallenbach , Larsen, RI8728, 1982) . This chemistry has been modified by Simplot in both patented and unpatented improvements. The objective of the beneficiation process was to reducethe A1203 content in the overall pipeline concentrate by 0.2 wt z. Therefore, a process stream was identified in the mill circuit which provided an opportunity to isolate and treat 1100 tons per day of poor quality phosphate concentrates The process allows recovery of approximately 15% of the mill concentrates, otherwise unsuitable for fertilizer production. The alternative would have been to waste this ore. Wasting would have resulted in considerable ore loss, increased mining costs and required additional products grinding. ]

Jan 1, 1989

By R. F. Yap

Although laboratory studies of tin flotation have been reported as far back as the 1920`s(1), the commercial application has only been realized within the past few years(2,3). The principal technical difficulty in the application of the process to tin ores has not been in the flotation of cassiterite itself, this mineral being readily recoverable with the common collectors, including xanthates with heavy metal ion activation(2). The difficulty has been with the depression of the gangue minerals commonly associated with tin ores, and to a lesser extent with the problems of collector consuming semi-colloidal minerals which are in some cases present. The application of sulfosuccinamate collectors to flotation of cassiterite from the Catavi, Bolivia, slime tailings has recently been described(3). The investigation which led to this successful process development included studies of other samples of gravity plant tailings as well as of lode tin ores. A common flowsheet with few significant variations was applied to most of these ore samples with acceptable results. In the following the process is described and the results of its application to samples from Bolivia and elsewhere given. Among the factors considered are: gangue depression, particle size and slime effects, and reagent and pulp density levels.

Jan 1, 1971

By Katherine Hynard, Colin Eustace

Development quarterly mine plans is generally time-consuming and requires consideration for many operational constraints and competing objectives. With lengthy turnaround times, there is often limited opportunity to adjust the quarterly plan details to account for differences between actual state of the mine operation at the time of execution and expected state at the time that the plan was developed. Actual mining task completion times can vary significantly from the expected task completion times, due to many factors. In the absence of revision to account for differences between the planned and actual state, resource allocations and mining sequences, embodied in the quarterly mine plan may no longer be the best approach at the time of execution to achieve an efficient mining operation. Simulation and optimisation tools can be used to support rapid refinements for development and execution of weekly mine plans. When initialized with an operations data feed to establish the actual state of the mine operation, optimisation models can be used to facilitate both automation and revision of the quarterly plan to produce a weekly or daily plan for execution. This approach can remove much of the manual burden of revision if the existing quarterly plan no longer represents the best approach to meeting production objectives. Following initialisation with mining actuals, simulation models can provide a representation of the range of likely mine operations outcomes. The models can be used to accelerate the planning process by providing visibility of future performance and identifying likely operational issues. They can also be used to test the robustness of the plan with respect to performance variability and response to disturbances. Following identification of issues, simulation models can also be used for evaluating mitigation measures, through automated testing of alternative plans. Integration of mine data feeds with simulation and optimisation tools enables automated optimal responses to variations between the quarterly mine plan and actuals to be tested prior to release of and execution plan and implementation. The use of simulation and optimisation in weekly mine planning will be discussed in this paper with reference to surface mining examples.

Jun 25, 2023

By Reed S. C. Rogers

There is recent evidence that high frequency screening can be a viable alternative to hydrocyclone classification for a wide variety of grinding applications. However, since high frequency screening is a relatively new development, the decision to use screens generally must be based on full scale screening tests of a slurry material of interest. In this paper the authors employ mathematical simulation models as an aid to evaluating the use of screens versus hydrocyclones for closed circuit fine grinding. This approach is validated in a pilot plant study and then demonstrated for the design of full-scale grinding circuit, including classifier cost comparisons. For the case of maximum production rates versus product size, without a constraint on fine product solids densities, results indicate that screening with Derrick sandwich type cloths can give higher grinding circuit production rates with more narrowly sized products than when hydrocyclones are used. These results are explained in terms of the bypass and Sharpness Index of the respective classifier partition curves. Classifier cost comparisons for the full scale circuit show that although the installed cost of screens is substantially higher than equivalent capacity hydrocylone operations, even modest increases in circuit capacity caused by screens; can significantly reduce total grinding costs.

Jan 1, 1985

By B. A. Kennedy

The instrumentation, monitoring, and prediction of a major slope failure at the Chuquicamata mine are described. In December 1967, pre-existing tension cracks on the south end of the east wall of the Chquicamata mine began to open. Various forms of instrumentation were installed for continuous monitoring. These systems included tension crack stakes, crack extensometers, linear extensometers, tape and transit lines, sliding wire contacts, and a seismograph. From the information obtained, the failure date was accurately predicted some five weeks before failure, enabling the mine to reroute truck and rail access; hence, causing a minimal mine shutdown of two and one-half days and preventing any injuries to persons or damage to equipment. The shape and form of the sliding mass are analyzed, as are the possible modes of failure.

Jan 1, 1970

By W. Bakiewicz

The Lower Indus Basin deposits form a substantial unconfined alluvial aquifer of excellent quality. This aquifer contains basically highly saline groundwater, overlain in places by considerable amounts of freshwater whose origin can be traced to the present and historical courses of the River Indus. In the past the main source of groundwater recharge has been direct river seepage and water tables were generally deep. Since the establishment of a perennial irrigation regime however, deep percolation from the increased irrigation supplies has predominated and the water-table has risen to within a few feet of the surface. The river system itself is being progressively developed for irrigation and very shortly a situation will arise where the entire low winter flow will be utilised. Fresh groundwater will then be exploited to supplement the surface supplies, and at the same time a drainage system, mainly based on wells will be used to stabilise the water-table at safe depths. This paper discusses some of the methods used to ensure optimum-economic development of the fresh groundwater and describes the general design philosophy evolved by the authors firms for both irrigation and drainage wells, with respect to both well configuation and operation. Water quality standards are discussed in as much as they affect subsequent use of the groundwater. A few particular aspects are considered, including that of the values of the relevant aquifer constants, the construction of wells and the determination of screen losses. A major problem solved during the Lower Indus Project investigations has been the design of wells to-produce fresh water from layers overlying saline water. This solution is also discussed.

Jan 1, 1967

By Felicia F. Peng

The plant data were collected from three streams around a dense medium drum for coarse coal cleaning operated at various volumetric ratio of medium-to-feed. The effect of the volumetric ratio of medium-to-feed (MF) and particle sizes on the performance criteria, g50 and Ep, of the dense medium drum. These measured data were adjusted and calculated for the yields and balanced relative density distributions by mass balanced method based on the statistic principle. These balanced data were then used to formulate the mathematical models of the separation distribution curves for the various feed size intervals. The correlation equations for the g50 and Ep as the function of inverse of the feed size, and MF and total throughput were established. A numerical algorithm utilizing the Secant method, based on the root searching principle, was developed for yield optimization and simulation of dense medium drum separation to improve the separation efficiency and hence the product yield. The relationships between the direct ash content and relative density of the particles in feed and the products were established and incorporated into the numerical algorithm for predicting the product quality.

Jan 1, 1996

By A. R. Rule

As part of the Federal effort to help maintain an adequate supply of fertilizer minerals, the Bureau of Mines is conducting research to characterize complex, low-grade western phosphate rock and to develop methods for economic recovery of phosphate. The rock varies from soft, friable, altered phosphatic shale to hard, tightly cemented, unaltered phosphate rock. To supplement current beneficiation by sizing, a flotation procedure was devised that included depression of phosphate minerals with H2SiF6 and anionic flotation of carbonate minerals, followed immediately by cationic flotation of silicate minerals. Application of the procedure to several different ores resulted in phosphate concentrates that ranged from 28 to 31 pct P20S in grade and from 60 to 70 pct in phosphate recovery.

Jan 1, 1977

By K. Thomson

The Mule Canyon gold deposit, located 14 miles ESE of Battle Mountain, Nevada, was discovered in 1986 as the result of a GFMC grass-roots exploration program. Drilling to date has identified six discrete orebodies which contain a demonstrated gold reserve of 8.487 million tons at an average grade of 0.136 oz/ton, totaling 1,152,000 ounces. Mineralization is associated with argillic alteration and silicification, localized along NNW trending high-angle faults within Miocene basaltic andesites. Trace element geochemistry at Mule Canyon is typical of upper level hot spring precious metal systems, displaying elevated Ag, As, Sb, Hg, and Se.

Jan 1, 1993

By Michael J. Fiannaca

Disseminated epithermal gold metallization occurs within a breccia unit interpreted to be a submarine debris flow. Cold is associated with oxidized pyrite, fluorite, and jasperoidal silica. A minimum of 9 million tons of open-pittable mining reserves will be cyanide heap leached as run-of-mine ore at a rate of 1.0 million tons per year. Careful evaluation of the combined results of successive sampling projects has established the pit plan, mineable reserves, and process metallurgy of the operation. The sampling procedure utilized for a given test depended upon geological interpretation as well as the procedures, successes, and failures of previous tests. This paper summarizes the sampling and testing procedures of the development effort in light of the project goals and attendant problems in achieving them.

Jan 1, 1984

By F. Calizaya

A booster fan is an underground ventilation device installed in the main airstream to handle the total quantity of air circulated to one or more working districts. It is installed in a permanent stopping and equipped with airlock doors, a monitoring system and interlocking devices between the main fan and the booster fan. When adequately installed, a booster fan can be used to reduce the main fan pressure, reduce leakage and decrease the power consumption. However, an inadequate installation can increase the likelihood of mine fies and recirculation of air contaminants. This study identifies hazards associated with the operation and maintenance of booster fans. It analyzes the accompanying risks and recommends control measures to reduce those risks to acceptable levels. The ventilation network of an existing coal mine was updated to include a booster fan. The hazards associated with the operation of this fan were identified, the risks analyzed and the esponse to each failure mode established.

Mar 1, 2014

By J. D. Shenk

The White Cliffs diatomite deposit occurs in a lacustrine facies of the Quiburis Formation, an Upper Miocene to Pliocene basin-fill sediment of the lower San Pedro Valley. On-going geo-logic mapping has defined an 2.5-3.0 m (8-10 ft) thick ore zone near the mill site, several marker beds, a NNW-trending high-angle normal fault, and a NW-trending syncline. The diatomite has an average loose-weight dry bulk density of 130 kg/m3 (8 lbs/ft3) and is presently marketed outside Arizona for asphalt filler. Current development is projected to yield 3500 mt (4000 st) of finished product, with an estimated 91,000 mt (100,000 st) of finished product obtain-able from several other nearby sites.

Jan 1, 1988

By Albert R. Rule

Beneficiation studies were made by the Bureau of Mines to develop a process for concentrating phosphate minerals from the altered rock of the Phosphoria Formation. This report describes research on intermediate - and marginal-grade ores from southeast Idaho, The process developed consists of attrition scrubbing and sizing to produce a coarse concentrate; desliming at about 800 mesh (18.5 microns); flotation of the fine sands; roasting of the combined concentrates for removal of organic carbon and combined water; and leaching with SO2 for removal of magnesium and nonapatitic calcite. Results of continuous tests on three different ore types showed that approximately 80 percent of the available phosphate can be recovered at a grade suitable for phosphoric acid production. While leaching with SO2 is not necessary for all ore types, it is an important step in purifying concentrates containing excessive magnesium.

Jan 1, 1966

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By S. Bahrampour

One of the basic requirements for designing an optimized rock support for an underground opening is having reasonably enough geological information. It is often financially impractical to obtain detailed geological information about the rock surrounding the excavations. The geological and geotechnical information which are obtained during the construction phase are also usually inadequate and need periodic operation stoppage. Penn State University- J.H. Fletcher & Co. joint venture is to improve the existing instrumented roofbolter so that the 3D geological and geotechnical map of the rock mass surrounding the underground working can be generated real-time as the data is being collected. This information will also be used to design appropriate support for different sections of mines. In this paper, recent results in improving the performance of the measurement while drilling system will be discussed. Moreover, updates related to borehole probing methods for estimating the properties of the rock masses will be presented.

Feb 23, 2014

The vast coal resources of North Slope, Alaska can be expected to attract substantial interest because the nearly flat lying coal beds of the coastal plan are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large scale coal mining and reclamation operations have not been carried out in the arctic The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the interrelationship between the problems due to permafrost and factors in reclamation of post mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1986