Search Documents

By M. A. Trevits, G. L. Finfinger

Various methods have been developed through US Bureau of Mines research to remove gas in advance of, during, and subsequent to mining. These include drilling horizontal or cross-measure boreholes from a mine opening, and vertical boreholes stimulated for drainage in advance of mining or for gob gas drainage. Techniques and equipment now exist that allow drilling a borehole at any angle to the vertical, and even along an arc. Stimulation treatments have also been developed that provide for increased gas production capability. This paper describes the long-term production history of five select gas drainage installations. The Bureau of Mines conducted or participated in four studies. The remaining study was conducted by the Equitable Gas Co. Principles of storage, release, and migration of coal bed gases The amount of gas contained within any given area of a coalbed depends on the coal's inherent storage capacity and the physical conditions of the coalbed. The gas storage capacity of coal is primarily a function of rank. As such, it cannot be affected by the presence of drainage holes (Kim, 1977). Certain physical conditions of the coalbed can, however, be changed that will affect the release and migration of gas. By pumping water out of the coalbed through the vertical boreholes, two important changes occur - pressure is reduced and water saturation is lowered. Reducing reservoir pressure releases gas as the coalbed adjusts and equilibrates gas to the change. Increasingly large amounts of gas are released for each incremental decrease in pressure. Lowering the water saturation level raises the permeability of the coalbed to gas and allows the gas to more readily migrate to the wellbore (Kisse and Edwards, 1975). For horizontal boreholes completed near mine openings, the coalbed has already undergone a pressure or water saturation reduction phase. This condition thus allows such boreholes to be highly productive with minimal water production. Case studies of coalbed gas production Pittsburgh Coalbed - Marianna mine 58 A methane drainage study was begun in July 1978 at Bethlehem Mines Corp.'s Marianna mine 58, Marianna, PA (Fig. 1). The work was conducted in a section of the mine that was advanced 1.5 km

Jan 8, 1986

By B. Tripp

Utah produces a wide variety of industrial rock and mineral commodities, valued in 2005 at a record $758 million (21 percent of the total non-fuel mineral production of Utah). Major commodities produced in 2005 include salts (halite, potash, and magnesium salts), Portland cement, sand and gravel, carbonates (lime, limestone, and dolomite), phosphate, crushed stone, clays, lightweight aggregate (expanded shale and perlite), gypsum, silica, sulfur and sulfuric acid, and building stone. Commodities produced in smaller amounts include diatomite, pumice, gemstones, ornamental stone, fluorspar, and mineral and fossil specimens. Utah is in a period of rapid growth in industrial rock and mineral production; however, some commodities have grown faster than others. The robust western economy has stimulated production of construction-related commodities like sand and gravel, Portland cement raw materials, lime, and building stone, resulting in exploration for raw materials, development of new quarries, and expansion of existing plants

Jan 1, 2007

By M. Karmis, S. K. Weisiger

The traditional method for training personnel in the mining and other heavy industries has been face-to-face, either via a lecturer in a classroom or through an apprenticeship. With the advent of applications tools such as video, computers, and the Internet, however, a much broader range of training delivery methods is available. Especially exciting are the broad capabilities of multimedia packages that combine the best features of numerous delivery methods. Applying multimedia environments in training holds great potential, especially when there is considerable difficulty in reconstructing real training environments. The authors discuss various delivery methods currently used in training employees, including perceived advantages and disadvantages of those methods. The authors then discuss and evaluate current computer-based training efforts of the mining industry and present an example of a multimedia training tool.

Jan 1, 2001

By Peter Bigwood

Whether drilling through tough clay or breaking rock, or facing the most severe conditions including mixed face ground, perched water and running and flowing sands, working under-ground certainly comes with no shortage of challenges. In an environment where the unknown is faced on a daily basis, tunneling contractors must be able to rely on their equipment to get the job done properly. Not only that, their equipment must comply with two of the highest priorities: safety and efficiency. In addition to being the number one concern, a proven safety record provides additional benefits to a company. A safe work environment serves as a key component to company growth, including the ability to remain competitive in bidding and maintaining higher-level, more challenging projects.

Jan 1, 2012

By Richard R. Klimpel

Introduction Froth flotation is one of the most common unit engineering operations in use today. Its aim is to upgrade the quality of coal by removing ash/pyrite and separating selected minerals from undesired gangue materials. Flotation has been successfully practiced at the industrial scale for more than 50 years. Its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation has also shown itself to be a flexible process that lends itself well to many solid/solid separations. Thus, with surprisingly little equipment modification, separations can involve very different particle sizes and densities, and relative weight ratios of materials to be separated. In addition, the flotation process is economic, especially when compared to size reduction, its associated precursor process. Flotation also lends itself to continuous operations with a given equipment configuration. The operation must exhibit an ability to vary feed rate of solid to the process by as much as 50% without a total collapse of separating efficiency. In addition, the mechanical flotation cell is scaleable from 2.8 to 57 or 85 m3 (100 to 2000 or 3000 cu ft) with surprising ease relative to other unit engineering operations over the same relative size increase. The separating medium used is water. Most of the chemicals required - pH regulators, frothers, collectors, activators, and depressants - are all relatively inexpensive and common. They are not usually used in large quantities. Froth flotation is certainly one of the most versatile and forgiving unit operations in the chemical, mining, and agricultural industries. The problem with the industrial flotation process is that it is fairly easy to get reasonable results and relatively difficult to get excellent results. Why is it so difficult to fine tune the froth flotation process? There are some obvious reasons and a few not-so-obvious factors. The obvious category would certainly contain the tendency of natural feed materials (ores and raw coals) to have variable physical, metallurgical, and surface properties. This occurs even when special care is taken to minimize such differences with blending. There is another obvious reason for difficulty. An inherent broadness of the feed particle size range to flotation results from using any of the common industrial-scalefine grinding devices - ball-, rod-, or autogenous mills. Research has been done into the chemical reagent and equipment aspects of flotation. It has shown strong interactions (limitations) of chemical reagents and equipment on larger and smaller particles. The point is that current flotation practice works best on average- or medium-sized feed particles. The greater the amount of large or small particles, or of both large and small, the more difficult it is to achieve excellent flotation results. Other reasonably obvious factors include: • variations in mineral type and liberation sizes; • water chemistry variations such as those involving Ca", C03, or Fe", or various soluble metal cations; • the presence of stray organic materials such as returning soluble reagents or partially degraded reagents in reuse water; • the lack of reliable on-line instrumentation for monitoring and control; • frequent equipment malfunctions of all types; • excessive feed rates for installed plant capacity; • poor operator interaction with the process; and • poor reagent dosage control. There are less obvious, but real limitations to flotation. These are inherent in the design and operating characteristics of the most common cell design in use today - the mechanical flotation cell. Individual performance attributes of the chemical reagents used, along with their manner of use, also carry limitations. The bulk of this paper will deal with chemical reagents and their use. Chemical reagents In 1979, the author and his co-workers were asked to invent and implement, at the industrial scale, new flotation reagent chemistry. After reviewing some of the literature (Sutherland and Wark, 1955; Klassen and Mokrousov, 1959; M. Fuerstenau, 1962; D. Fuerstenau, 1976; and Leja, 1982), a series of carefully controlled plant scale tests were set up. These tests were designed to understand existing reagent scale-up from the laboratory to the plant. They were to quantify at the plant level the effect of some of the more important, controllable chemical reagent factors (frother and collector type, frother and collector dosage, pH effects). This is a learning experience that all researchers involved in flotation theory should experience. It quickly became apparent that: • because a factor is important

Jan 12, 1988

By Rex E. Loesby

The marble deposits of Yule Creek were first discovered in the late1870s. Minor quarrying occurred between that discovery and the early 1900s. Major development occurred in 1905, when Channing Meek, with some help from the Rockefellers, raised $3 million to develop the Colorado Yule Marble Quarry. That is $50 million in today’s dollars. Some of the words used to describe the marble deposit were “gigantic, remarkable, flawless and immense.” Boosters proclaimed, “The marble age is here.” Obviously, dreams were big for Marble.

Jan 1, 2003

By Eric M. Hill, Daniel E. Walsh, Hsing K. Lin, John T. Hollow

The Fort Knox Mine is located in Alaska’s interior where the average ambient air temperatures range from -24°C in January to 16°C in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Plant slurry temperature cycles seasonally and allows for a unique opportunity to measure the impact temperature has on gold leach kinetics, carbon adsorption efficiency and cyanide destruction reactions. Mathematical models have been developed to accurately predict actual mill performance. This paper describes the development of the models and presents data that allow for a better understanding of the impact of circuit operating temperature on process efficiencies.

Jan 1, 2005

By J. M. Dean, R. L. Grayson, R. C. Althouse, M. J. Klishis, G. L. Winn

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Feb 24, 1997

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By C. Arthur Lefler

The hydrometallurgical processes for recovery of gold and silver in use at Round Mountain, Nevada and the practical aspects of the operation are discussed. Included are heap leaching by cyanidation, upgrading of solutions by adsorption of values on activated carbon and desorption (stripping) for electrowinning and subsequent refining steps to produce dore metal.

Jan 1, 1981

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

Jan 1, 2006

By Jürg Schlumpf

Concrete is one of the decisive construction materials, also for the AlpTransit Gotthard Tunnel. The client has many requirements, and many are the solution possibilities that concrete systems can offer. Cement producers and concrete admixture manufacturers have been challenged to design and test jointly concrete systems for cast and sprayed concrete. The testing operation followed the scenario laid out by the Gotthard AlpTransit Project management?s instructions ?Testing system for concrete mixes.? Various supplier teams have applied for the concrete systems for sections Amsteg/Erstfeld, section Sedrun and/or sections Bodio/Faido and have also followed through with the tests. As was to be expected, the rate of failed mixes matched the level of the requirements. Thanks to this system, it was nevertheless possible to test complete concrete systems for all sections and to get them approved. The joint ventures tendering for the contracts were allowed to include only approved mix designs in their bids. Workability and durability are of paramount importance for cast and sprayed concrete mixes. Durability is influenced by the chosen mix design where binder concept and well-defined water content, i.e., impermeability, are determinant. Aggregates for AlpTransit are to be considered as given. The concrete mix design also determines workability. Because ambient conditions and also requirements with respect to workability are subjected to change, it is necessary that the mix designs include control measures. The choice and number of components for the concrete systems (cement, additives and admixtures) allow adaptation to changing conditions. For AlpTransit such adaptive measures must meet very strict requirements.

Jan 1, 2008

By D. R. Wilburn

The worldwide budget for nonferrous, nonfuel mineral exploration was expected to increase by 58 percent in 2004 from the 2003 budget, according to Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes two years after a five-year period of declining spending for mineral exploration (1998 to2002). Figures suggest a subsequent 27 percent increase in budgeted expenditures from 2002 to 2003. For the second consecutive year, all regional exploration budget estimates were anticipated to increase. The worldwide budget for gold exploration achieved about 50 percent of the total amount budgeted in 2004.This was 68 percent, or US$715 million, higher than the reported 2003 budget. The 2004 worldwide exploration budget estimates for copper increased by 70 percent, orUS$237 million, to US$577 million from the 2003 budget. The budget for nickel exploration increased 52 percent, or US$89 million more than in 2003. The 2004 exploration budget for other mineral targets (primarily cobalt, heavy minerals, industrial minerals and silver) increased114 percent, or US$118 million.

Jan 1, 2005

By T. L. Owen

Since 1993 Cyprus Amax has brought $2.5 billion dollars of greenfield and expansion projects into production, taking it from a mid-sized domestic minerals company into a major international minerals organization. The near simultaneous development of these multiple mineral projects in different locations around the world provided the opportunity for Cyprus Amax to develop a formal project management approach based, in large part, on an outsourcing philosophy. This formal project management system along with its outsourcing philosophy has served the growth agenda of Cyprus Amax extremely well. These preceding factors, coupled with the in-house retention of a core project group that fully understands the breadth of skills and abilities needed to undertake development of multiple large projects successfully, have been the cornerstone of Cyprus Amax’s project development success.

Jan 1, 2000

By Michael Rehbock-Sander

The Gotthard Base Tunnel (GBT) is 57 km (35 miles) long and consists of two par-allel single-track tubes with an ex-cavation diameter ranging from 8.8 to 9.5 m (28.8 to 31.2 ft). These are interlinked by cross-passages every 312 m (1,000 ft). Two multifunction stations (MFS) are located in the sections Sedrun and Faido, at one-third and two-thirds of the entire tunnel length (Fig. 1). These will be used for the diversion of trains to the other main tube via tunnel crossovers, for the housing of tech-nical infrastructure and equipment and for potential emergency stops. To reduce construction time, the GBT was divided into five sections and was excavated from several sites simultaneously. The tunnel was excavated from the two portals, Erstfeld in the north and Bodio in the south, and also from three intermediate attacks, with their corresponding access tunnels, in Amsteg and Faido and two vertical 800-m (2,624-ft) deep shafts in Sedrun.

Jan 1, 2012

By J. Egan

The recovery of gold by ore leaching is influenced by the size of the particles and the chemical environment. Within the experimental error associated to the testing of gold ore, results of a series of leaching tests conducted with natural ores rather than monosized samples confirm that gold dissolution increases with decreasing ore particle size. The tests also indicate that the dissolution of gold in the ore within a size interval is weakly affected by the intensity of the size reduction method.

Feb 27, 2013

The 112th Annual National Western Mining Conference (NWMC) hosted by the Colorado Mining Association (CMA) drew some political heavyweights, if by voice only, into the fray of two of the hottest topics that the mining industry is currently facing ? climate change and the new energy economy. A changing political landscape in Colorado, as well as in Washington D.C., has given rise to questions about the economic future of the United States and the mining industry?s role in that future. While there has been a recent push away from traditional energy sources to a ?new energy economy? that is rich in renewable energy sources such as wind and solar, the NWMC?s agenda emphasized the role that minerals will play in new energy technologies. The conference was also full of talks about the industry?s role in reducing the United States? reliance on foreign oil and other mineral commodities. To that end, an impressive lineup of speakers were invited to attend the three-day conference Feb. 8-11, in Denver, CO. Unfortunately, Mother Nature had other plans and three of the four headliners, including Denver?s mayor and Democratic candidate for governor of Colorado, John Hickenlooper, were unable to get to the conference because of a massive blizzard on the East Coast locked them in Washington, D.C. However, with modern technology, a full auditorium heard presentations from Hickenlooper, National Mining Association (NMA) president and chief executive officer Hal Quinn and Glenn Kelly, vice president, government affairs for NMA. Republican candidate for governor of Colorado, Scott McInnis, did speak to the crowd in person.

Jan 4, 2010

The National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study to optimize the rib control plan in a room-and-pillar coal mine. The study mine is located in the Central Appalachia coal basin. Two monitoring sites were selected at different sections in the study mine. The selected sites have different overburden depths and geologies. The instrumentation plans at study sites include borehole pressure cells installed at various depths in studied pillars, rib and roof extensometers and load cells mounted on number of the rib bolts. The instrumentation results and observed geology for one of the study sites showed great potential for optimizing the rib bolt plan at that section of the mine. Therefore, a rib support optimization study was followed using numerical modeling technique. A calibrated threedimensional model was developed using the instrumentation results of the optimization section. The calibrated model was used to determine the optimum rib support for expected overburden depths and rib heights. Baseline rib bolt patterns were assumed for the optimization study. Additional rib bolts, above and beyond the baseline bolting parameters, were outlined and identified as solutions to contain the rib fracturing identified by the modeling results.

Jul 28, 2020

By H. Hejny

"The mine of the future will exploit mineral raw materials at greater depths than today, requiring completely different approaches compared to today’s deep mines, in order to get mineral rights. Only these eco-efficient mines will contribute to improved access to domestic mineral resources, secure the sustainable supply of mineral raw materials for Europe and reduce the import dependency. IntelliMine will contribute to realise these concepts of invisible, zero-impact and safe mines. The mine of tomorrow will run an integrated concept in order to guarantee the desired level of sustainability. All operations necessary for the eco-efficient provision of the minerals including waste management will be carried out underground. This will drastically reduce the volumes being transported, minimising above ground installations and thus the environmental impact. IntelliMine will develop necessary innovative methods, technologies, machines and equipment for the safe, eco-innovative, intelligent and economic exploitation of mineral raw materials in the EU, especially at greater depths."

Jan 1, 2011

By J-P Franzidis

A study was undertaken to determine the effect of five industrial frothers on the relationship between entrainment recovery and water recovery. The experiments were conducted using a Batequip rectangular 60 liter steel cell which was run in parallel with the first cell in a copper/silver prefloat rougher circuit. The concentration of the frothers ranged from 2.5 g/ton to 8.4 g/ton. The experiments were repeated at three different froth depths. A power function was found to fit this relationship with no discontinuity in the relationship caused by the changes in frother type and concentration and froth depth.

Jan 1, 2000