Search Documents

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By Kenneth K. Humphreys

Over the past four years, the Coal Research Bureau of West Virginia University has presented a number of papers on operations research in the coal industry before various AIME meetings and meetings of other societies. These papers have been followed up by further presentations in the technical press. The emphasis of all of these papers has been to demonstrate applications of operations research to the solution of numerous types of coal industry problems. In each case, effort has been made to demonstrate that operations research does not require extensive knowledge of computer science or use of sophisticated higher mathematics. In fact, for most applications, satisfactory results can be obtained by a single individual in a minimum of time with no aids other than a pencil and paper and a knowledge of basic arithmetic. The most recent efforts by the Coal Research Bureau have been directed toward the continuing industry problem of optimizing the location of mining facilities. Preliminary work in this area was presented before the Central Appalachian Section of AIME and subsequently published in the May, 1972, issue of Coal Age. This initial presentation illustrated techniques for determining optimum locations of facilities based upon material transport effort under the assumption of constant cost per ton mile of haulage effort. The present paper will expand upon this earlier work and introduce economic factors. In the design of a mine or mining system, careful consideration must be given to the sites selected for each element of the system. Optimum placement of facilities is vital to minimize capital and operating cost. Thus, barring unfavorable geological conditions or other exceptional factors, facilities should be located at those points which represent the minimum cumulative cost over the life of the property. Most cost factors are independent, or essentially independent of the location of fixed facilities. Thus, for example, regardless of the location of the shaft, the direct cost to mine any given ton of coal is essentially constant. The major 1

Jan 1, 1972

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

This paper describes the scientific data acquisition, data interpretation, and sophisticated 3-dimensional modeling processes of an ongoing gas well stability research program by the National Institute for Occupational Safety and Health (NIOSH). Results from the NIOSH field instrumentation programs and the parallel 3-dimensional numerical modeling programs indicate that overburden depth, overburden geology, surface topographic relief, strata dip of the coal measure rocks, and casing cementing alternatives are the dominant factors affecting longwall-induced subsurface deformations and gas well casing stresses. Topographic relief could produce localized longwall-induced deformations if weak-to-strong rock interfaces are present near the bottom of stream valleys. Strata dip has significant impact on longwall-induced subsurface deformations. Cementing alternatives are found to have significant impacts on longwall-induced deformations and gas well casing stresses.

By L. Rudolphy, P. Tähkiö

"The cPlant is a modular flotation plant which has been designed to minimize capital expenditure and risk. The plant is based on a number of standard modules, for both flotation and ancillary equipment, which can be configured to give the required flowsheet for the ore being treated. All of these modules can be rapidly deployed and erected onsite, minimizing not only engineering time and site preparation but reducing the time taken to get the plant up and generating revenue. Given the paradigm shift in flotation circuit design that has been employed in the cPlant it may allow smaller, previously uneconomic deposits to be exploited and create a more cost efficient upgrade route for existing plants. This paper introduces the cPlant and presents a case study comparing EPC cost and development timing of a cPlant against a traditional flotation circuit design. INTRODUCTION In the development of any mining project the cost associated with process plant engineering, equipment procurement and installation can affect the financial viability of a project. This is of special significance for smaller scale mining projects which perhaps don’t have the mine-life or revenue generation to justify the payback on a modern processing facility. Listening to customer feedback and understanding the challenges that small to mid-sized projects can face lead Outotec to the development of the cPlant. Modularization of mineral processing plants isn’t a new idea with a number of examples being reported in literature for gravity gold (Cabot, Trudel and Cabot, 2001; Gray et al., 2006), dense medium separation (September and Abate, 2006) and even hydrometallurgy (Saario et al., 2013). All these plants have been developed to try to improve on the traditional economics associated with fixed processing plants. Using standardized modules to construct a plant reduces engineering time and design costs which can both be beneficial to the outcome of a project. In addition the modular nature of the plant lends itself to transport to remote sites and rapid installation with only minimal site preparation required. A plant of modular design also has several other advantages over its conventional cousins. Firstly it is relatively easy to expand by duplicating existing modules. Secondly the modules can be treated as building blocks for the process and rearranged if a change in conditions requires flowsheet adjustment. Thirdly, there is potential to disassemble and remove the modular units at the end of the mine life. The ability to easily disassemble, re-pack and transport the plant to a new location not only is important to the long term environmental footprint of an operation but can also be seen as a bonus to an operator that has a number of small ore deposits. If applied in this way modular plants have the potential to create a whole new operating model for previously unviable ore deposits."

Jan 1, 2016

By D. W. Struhsacker

Mineral exploration has evolved into a sophisticated science which uses powerful scientific tools to make mineral discoveries. In addition to their usefulness in performing mineral exploration, these scientific tools can assist the exploration geologist in assessing environmental conditions at exploration sites. During exploration, environmental data acquisition should focus on data collection efforts which can be easily integrated into exploration activities, and should provide information needed for pre-feasibility and preliminary engineering design studies. Environmental studies performed during exploration should also include an environmental liabilities audit and a fatal flaw analysis to assess whether there are any unresolvable environmental or regulatory issues affecting the project. Performing extensive environmental baseline studies during exploration and project evaluation is neither necessary nor recommended. This paper describes opportunities to integrate environmental data collection with mineral exploration activities. This paper also examines how political and communication issues can affect the outcome of permitting efforts, and recommends a strategy to improve the industry's ability to respond to political challenges and to communicate with the public. This strategy integrates technical and political issues, and implements programs to convince the public of the mining industry's technological achievements and its commitment to resource stewardship and environmental protection.

Jan 1, 1994

By Alban J. Lynch, Khairun Azizi

Education and research have always followed production in the mineral industry. Almost all of the leading mineral education and research units in the world today are in developed countries which had strong mining industries created during the 19th and 20th centuries to meet the demands for minerals due to the Indus- trial Revolution. It is in those countries where the main advances in mining and metallurgical technologies have occurred. But it is in the developing countries, often with traditions which have not favoured engineering initiatives, that the mineral industry is growing. Legislative changes and high exploration expenditures in many of those countries are of such a nature that many mineral discoveries will be made and mines and plants built in them during the next decades. Developments must be accompanied by increased activities in education, research and technology transfer in mining and processing, particularly those which are computer based. Malaysia is a developing country with the objective of achieving developed status by 2020. It has a short history of tertiary education and industrial research and a growing mineral industry. It is now building the education and research programs which will give strong support to its mineral industry. The progress which is being made in the computer based components of these pro- grams, and the factors which influence them, are discussed.

Jan 1, 1996

By M. Ge

An in-seam seismic (ISS) - based void detection technique was developed and tested for three general mine conditions: anthracite, bituminous and trona. The detection range tested varied from 80 to 100 m for trona mines and from 33 to 66 m for bituminous mines. High quality and broad band signals were obtained from these tests and were used to delineate the voids. The paper provides a brief discussion on the technical features of this void detection technique, the testing conditions and results, and a general assessment of the technique.

Jan 1, 2010

By B. H. Kim, S. J. Schatzel, K. M. Ajayi, G. S. Esterhuizen, D. W. H. Su, Z. Khademian

The stability of shale gas wells drilled through current and future coal reserves can be compromised by ground deformations due to nearby longwall mining. Depending on the longwall-induced rockmass permeability, the high-pressure explosive gas from the damaged well may reach mine workings and overwhelm the mine ventilation systems. This study uses geomechanical models to estimate the rockmass permeability induced by mining. A two-panel longwall model of a deep, 341-m-cover mining site in southwestern Pennsylvania is constructed in 3DEC to explicitly model the rockmass by a Discrete Fracture Network (DFN) technique. Stress-induced fracture apertures and permeabilities are calculated across the model and are validated against permeability measurements. A Fracture Flow Code (FFC) is developed to use these results to predict potential inflow to the mine should a gas well breach occur. One hundred DFN realizations are simulated, and the results show that for a gas pressure of 2.4 MPa, the average of the predicted inflow rates to this deep-cover mine is 0.03 m3 /s, significantly lower than the average inflow of 0.92 m3 /s for a shallow-cover mine (145 m deep) studied in the previous work (Khademian, et al. 2021). The result can help assess the potential hazards of a shale gas well breach for mine safety and evaluate the ventilation requirements to mitigate the risk

Mar 2, 2022

By G. M. L. Robinson

The Clean Water Act, as administered by the Environmental Protection Agency, has mandated industry, government and the public to comply with potentially conflicting and vague water quality statutes, regulations and guidelines. Universal regulatory strategies have been developed which have introduced and have created regulatory, compliance and institutional conflicts. Conflicts have been created because National water quality performance goals and design standards are vague, and, in many cases, cannot be scientifically justified. Because of regulatory technical requirements to define background and environmentally impacted water quality characteristics, the ability to achieve regulatory compliance is difficult. Difficult issues requiring resolutions includes but are not limited to site specific surface and ground water quality classification systems, water quality standards and guidelines, point and non point pollution sources etc. Because of these statutory and regulatory complexities, a confrontational regulatory system has been created as it relates to: - defining performance criteria in relation to design criteria; - resolving water quality statistical compliance conflicts; - defining laboratory precision requirements; - determining background groundwater characteristics; and - locating a representative point of compliance. Because of these complex regulatory issues, the ability to balance goals, needs and economics has not been achieved or in many cases has not been attempted, without legal intervention. A few examples illustrating where water and waste management compliance conflicts have been experienced.

Jan 1, 1992

By A. K. Kuhn

In virtually all jurisdictions, comprehensive environmental protection regulations or standards are in place that apply to all industries, including mining. The only other legitimate mine-permitting concern is post-mining land use (PMLU). PMLU includes all uses of land after mining as well as the ecosystems appropriate for those uses. Although flawed, the New Mexico Mining Act (NMMA) of 1993 is a PMLU-based permitting statute. It requires measures during closure that will establish a PMLU or self-sustaining ecosystem for each mine unit. PMLU-based permitting avoids prescriptive, one-size-fits-all measures and keeps permitting focused on the legitimate goal of responsible land management..

Jan 1, 1999

By Dirk van Zyl

It can systematically assess if the control and management systems designed for protection of sensitive ecosystems are adequate. The results of the assessment can help to identify key elements in the project that pose higher risks due to uncertainties in design. These assessments can then be used to make recommendations to further manage and reduce risks as the project is developed. QUALITATIVE RISK ASSESSMENT The general principles of a risk assessment are well summarized by Kaplan and Garrick (1981): "In analyzing risk we are attempting to envision how the future will turn out if we undertake a certain course of action (or inaction)." Fundamentally, therefore a risk analysis consists of an answer to the following three questions: What can happen? (i.e. what can go wrong?) How likely is it that that will happen? If it does happen what are the consequences?" Risk assessments can be performed using various levels of sophistication depending on the amount and accuracy of data available. A qualitative risk assessment uses descriptors throughout to express the level of risk. The definitions of the descriptors are presented in terms of the magnitude or concentration of contaminants. The results of a qualitative risk assessment can be used to: a)Document the evaluation and decisionmaking process. Although differences of opinion may exist about the definitions of the descriptors, the process is well-documented; b)Express the relative risk associated with specific activities or design elements; and, c)Select those failure modes or release mechanisms that may result in significant risks. These mechanisms can then be further developed in quantitative risk assessments. A qualitative risk assessment can be performed in a systematic approach using four steps (Van Zyl, 1987): A qualitative environmental risk assessment can be used to describe the risks associated with the development of a new mine and to make an evaluation of the adequacy of its design for environmental protection. The relative magnitude of risk associated with selected failure modes and exposure/consequence scenario assessments is the final result of a qualitative risk assessment. These failure modes are based on site specific areas and components, and mining and construction phases. The four steps of a risk assessment (hazard assessment, exposure assessment, consequence assessment, and risk characterization) are used in the development of a qualitative risk assessment. Relative magnitudes (using a five point scale of negligible to high) for each step, can be quantified in a qualitative risk assessment. Development of the descriptors for the relative magnitudes in each step is a very important part of a qualitative risk assessment. The success of a qualitative risk assessment depends on the adequacy of the information base and the subjective judgements made in each step. The quality of the risk assessment is, therefore, dependent on the experience of the assessors. A mining project in a sensitive coastal environment is presented as an example to demonstrate the application of a qualitative risk assessment. INTRODUCTION Environmental impacts from mining operations have been a significant factor in the last century. This was especially the case prior to the development of a better understanding of environmental processes and the potential impacts of acid rock drainage (ARD), and associated heavy metals, or the uncontrolled disposal of tailings and waste rock (Smith, 1987). Much care has been exercised over the last two decades in designing and operating mines to limit the environmental impacts as far as possible. All new mines are specifically designed with mitigative methods to manage such potential environmental impacts. Attention is directed to ARD impacts, safe disposal of mine waste rock and tailings, transportation and storage of chemicals and fuels, and final reclamation. A qualitative risk assessment can be used to address all project systems and activities that may potentially pose a risk to the environment.

Jan 1, 1992

By T. Lupek, S. Plaum

"The execution of classical building services in underground mining operations is more truth than myth. From small concrete foundations for conveyor belts to the construction of huge workshops for large machinery maintenance, nearly every operation requires building services. By creating such fixed facilities, these services ensure the efficiency of the production. A distinction must be made between fixed facilities which directly enable the production and auxiliary facilities which only indirectly support the production. The construction costs of such auxiliary facilities are often roughly estimated because they do not immediately contribute to mineral extraction. The research project ‘Development of a systematic cost-calculation method for building services in underground mines’ seeks to address the question: ‘Can the construction costs concerning fixed auxiliary facilities be neglected e.g. within a prefeasibility study?’ The presentation will show the monetary relevance and significance of these auxiliary facilities and introduce a guideline for cost estimators. PROBLEM DEFINITION The overriding interest of an underground mining operator is to exploit the commodity with the maximal quality by minimum cost and time expenditure. If a new operation shall be installed, it has to promise profitability. Therefore, predictive economic feasibility studies are performed in advance of installation. Herein, all cost expenditure for installation and operation of the future underground mine is determined and compared to the expected income by selling the raw material. The described interest of the mining operator is the starting point of the research project ‘Development of a systematic cost-calculation method for building services in underground mines’. While economic feasibility studies for future operations are focused on the profitable exploitation of raw materials and the efficiency of the accompanying necessary production processes, auxiliary actions are only considered rudimentary. Necessary production processes, as well as auxiliary actions regularly require classical building services, which are normally performed in construction business on the surface in the same manner. By performing building services like masonry or concrete works in underground mines, fixed facilities shall be set up in order to enable or support the raw material production. Production enabling fixed facilities are varying from small concrete foundations for conveyor belts or other infrastructural elements to upstream processing plants situated in the mine workings. While such fixed facilities are essential parts of the production process chain, supporting facilities underground shall increase the efficiency of the mining operation. Workshops, control rooms and social installations are only a few examples for supporting facilities. Those could be situated on the surface as well, but the efficiency increases significantly by installing them underground. Especially supporting facilities are evading from the main interest of the mine operator, since they are only indirectly connected to the production process. The building costs are oftentimes only roughly assumed."

Jan 1, 2017

By J. R. Allan

Loki Gold Corporation of Vancouver, B.C. is developing the Brewery Creek Mine, an open pit heap leach gold mine, 55 km East of Dawson City in Yukon, Canada. Mineable reserves are 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797 000 oz) of gold. Ore processing will employ a cyanide heap leach using run of mine ore. Permitting this mine has drawn significant attention because the heap leach technology, while proven in other jurisdictions, has not been used in Yukon. Engineering design of the heap leach was similar to that for heaps in more temperate climates, with the added issues of permafrost and cold weather operations. Solution balance with seasonal placement of ore and year -round leaching requires very large pond capacity for spring thaw conditions.

Jan 1, 1996

By R. L. White

Classification of Mills Mills may be classified under four categories that relate to the type of action utilized to grind the material: Tumbling. The most important of these to the minerals processing industry are tumbling mills. Grinding media is actuated in a free¬form pattern in a rotating drum causing it to tumble, material being ground passing through the tumbling media. Work is done by a combi¬nation of attrition and impact. Impact. Grinding media is actuated in a distinctive pattern so that it impacts the material being ground. Work is done by impact. Roller. Grinding media is actuated in a distinctive pattern, mate¬rial being ground passing under or between the media. Work is done by compression. Fluid Energy. There is no grinding media as such. Energy is imparted to the material by transfer of kinetic energy from the fluid to the material. Grinding is accomplished by interparticle impact and attrition. Tumbling Mitts The main physical arrangement consists of a lined cylindrical drum mounted on trunnion bearings driven by a ring gear and pinion, in turn connected directly or through a reducer to the electric motor. Variations to this general arrangement include: (1) Drum mounted on rollers instead of trunnions. (2) Bearings on the drum directly, not on trunnions. (3) Utilization of multiple pinions on the gear. (4) Trunnion-type drive arrangement through a gear reducer with¬out the use of a ring gear. (5) Motor rotor mounted directly on the drum with stator around the drum, thus eliminating the gearing. The drum consists of a shell and heads lined with replaceable liners of various types and configurations. Various types of tumbling mills are tabulated; illustrations of some are shown. The types are so designed for specific purposes. Media utilized include steel rods, balls, or rock of the same material as being ground or of special material in the instance where iron contami¬nation is detrimental (see Figs. 9 and 10 and Table 2). Impact Mills Although there may be some overlapping of interpretation of terms, impact mills are considered those in which the media is actuated in a distinctive manner, at relatively high speed, impacting the material to be ground. There is an overlapping also in what may be considered to be crushing equipment rather than grinding equipment. Hammer Mill or Impactor. Material is fed into the equipment; inside hammers of impactors revolve at a high speed, breaking the material on impact with the hammers (see Fig. 11). Material is also thrown against the periphery of the mill, causing impact grinding to occur. Equipment is normally lined with replaceable abrasive resis¬tant metal; hammers are also

Jan 1, 1985

By T. A. Moss

The installation of equipment and structures at mines often requires the evaluation of unique loading and operating conditions. Consideration of these unusual features is required throughout design and construction and into operation. The necessity for employing sound civil, structural and mechanical engineering techniques to the design of structures and equipment is well understood. However, the influence of geotechnical factors on the overall behavior during construction and operation of these facilities is less appreciated. Mine operators routinely perform exploratory drilling for the purposes of defining ore deposits. These exploration activities can be extensive and often include provisions for assessment of subsurface conditions as they relate to the mining operation, i.e., requirements for ground support. All of these factors are important to the economics of the mine and are well justified. Surface facilities are provided to access and service the mine and they play an important role in the successful development and operation of a project. Headframes, hoist foundations and shaft collars, in particular, are examples of unique installations encountered at underground mine sites. The design and above surface behavior of these facilities can be analyzed with the usual fundamental engineering practices employed throughout the engineering professions. This requirement during the project development is understood and adopted. Unfortunately, near surface exploration for the purposes of assessing soil and rock conditions for foundations are often given a reduced priority and less consideration. This paper is aimed at providing an outline into the benefits and importance of performing such explorations and to provide a brief discussion of the merits of such an approach. References in the paper relate particularly to shaft headframes, hoists and shaft collars but the issues raised apply equally well to other installations of a similar nature, e.g. milling equipment.

Jan 1, 1992

By Bhaskar B. Thapa, Michael T. McRae, Michael J. Teske, Richard M. Nolting

Packer test data and tunnel in?ow observations are used to show that the distribution of equivalent hydraulic conductivity obtained for a rock mass from borehole packer testing will be biased if the orientations of the planned tunnel and testing borehole differ. Furthermore, test results show that the distribution of equivalent hydraulic conductivity is different in various geologic sub-units at the same site. The impact on in?ow of the major uncertainties, including conductivity, head and specific yield, is illustrated to be amenable to a combined analysis using Monte Carlo simulation.

Jan 1, 2003

By M. J. Virnig, C. P. J. Van Vuuren, A. J. Botha

The Zadra, AARL and organic elution processes and variations of them are presently widely used to recover gold from activated carbon. Despite this the study of the kinetics of elution have received relatively little attention. It is the aim of this study to investigate the rate processes taking place during elution in both inorganic and organic solutions. Batch adsorption and elution rate and equilibrium experiments were performed. The spatial concentration of gold inside carbon particles at various stages of the adsorption and elution processes were measured with a scanning electron microscope using an image analyzer to control and manage the micro-analysis data. The activated carbon particles exhibited film and intra-particle mass transfer rate- controlled behaviour during adsorption in a caustic aqueous solution at 95°C. Elutions in the aqueous caustic acetone solution at 30°C and the caustic aqueous solution at 95°C were unaffected by change in stirring rate. Elution was modelled by desorption reaction rate-control at the outer surface of the carbon particle. Adsorption and elution isotherms under duplicated solution conditions showed reasonable agreement for the inorganic solution and a large disparity for the organic solution.

Jan 1, 1993

By John Frostiak, Don Welch, David Landriault

The use of paste technology for underground cemented backfill is widely accepted in the mining industry today as a potentially cost effective alternative to cemented rock and hydraulic slurry fill. While paste backfill is not the appropriate backfilling method for all mines, there are presently 23 operating tailings paste backfill plants throughout the world. This new technology has gained increasing acceptance as a backfill method over the last decade and its use is now expanding into the surface disposal of tailings using the stacked, thickened tailings disposal concept. Over the next 18 months there will be ten new paste plants commissioned in the world. Five of these ten plants will be used exclusively for surface tailings disposal or a combination of surface disposal and underground backfill production. The thickened tailings disposal concept, developed by Dr. Eli Robinsky in the early 1970's, has been in use for decades at several mine sites throughout the world (Kidd Creek Mine site in Northern Ontario), but always utilizing non segregating high density tailings slurry central discharge, stacked tailings placement. With the use of a higher solids content paste, the typical 2-degree beach angle can be increased to ten degrees or more with no runoff water and minimal shrinkage crack development through desiccation. This paper presents the design of the first mine to implement true surface paste disposal, Barrick Gold Corp's Bulyanhulu Mine in Tanzania. The paste system will be commissioned in the first quarter of 2001 allowing performance data to be collected to define the full potential of paste technology for surface tailings disposal.

Jan 1, 2001

By M. Cimini

The main objective of this paper is to propose a new sustainability parameter, called Visibility Indicator (VI), to describe the influence of mining operations on the visibility of the open works in the site from the surrounding land. A further goal is to point out a procedure for Visual Impact Analysis and Assessment (VIAA) of mining and quarrying operations in the phases of elaborating and evaluating of the project and depleting the resources. The Visibility Indicator has been computed taking into consideration the evolution of the area involved in the exploitation activity.

Jan 1, 2003

By Romeo Jurani, Ralph Dresel, Fred Kissell, Charles Parker

This report describes actions taken to control silica dust at the Yucca Mountain Exploratory Studies Facility (ESF), a tunnel located in Southern Nevada that is part of a scientific program to determine site suitability for a potential nuclear waste repository. The rock is a volcanic tuff containing significant percentages of both quartz and cristobalite. Water use for dust control was limited because of scientific test requirements. A major dust reduction was achieved with an intermediate air cleaning station located on a rear deck of the TBM trailing gear.

Jan 1, 1999