Search Documents

By M. A. Cocquerel

INTRODUCTION Davy McKee have developed and patented a combined mixer settler (CMS) which has undergone extensive trials and has now been installed in two commercial uranium plants in South Africa. Substantial capital and operating cost savings can be realized over conventional mixer settler in uranium extraction, especially from dilute feedstocks containing approximately 200 ppm U308. Pilot plant work has also been undertaken on other metal extraction systems and the results are very encouraging in most areas of interest. CONVENTIONAL MIXER SETTLERS The conventional plant in use at many uranium recovery facilities consists typically of a mixer box in which the aqueous and organic phases are contacted and a settler in which the two phases separate. The mixer box must allow sufficient residence time for the mass transfer kinetics to be satisfied for the particular species involved. The settlers are usually rectangular and take the form of shallow tanks of large cross sectional area.

Jan 1, 1984

By M. D. Martin

Low metal prices and increasingly stringent environmental regulations, coupled with the threat of higher governmental royalties are adversely affecting both existing and new operations. Existing operations must therefore be run at maximum operating efficiencies to enable mining companies to survive and grow. Well planned and executed "outsider" reviews can help achieve this goal. Many mine managers and those who direct them resist the idea of "outsider" reviews for a variety of reasons, some valid and some not. Those managers who do bring in the "outsiders" are nearly unanimous in reporting that the exercise in self-discipline was well worth the pain and effort and repaid the cost many times over. This paper makes a strong case for "outsider" reviews and gives recommendations on the kinds of reviews to undertake. The authors draw upon their nearly 70 years combined experience, much of which has been in operations.

Jan 1, 1994

By J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m (36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM -800 Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By Dean H. Herrick

The production of crushed stone in the United States has exceeded 1.0 Gtpy since 1987. Eighty percent of the crushed stone produced is used in the aggregate industry, accounting for over half of the quantity of natural aggregate consumed in the United States. Approximately 718 of the crushed stone produced in 1989 was limestone and dolomite followed by granite, traprock, sandstone and quartzite, miscellaneous stone, marble, shell, calcareous marl, volcanic cinder and scoria, and slate in order of descending volume (Table 1). Of the remaining 20% crushed stone produced in the United States and not used as aggregate, 12% is used in the manufacture of cement which is an important construction material. Only 8% of crushed stone is used in specialty products not associated with the construction industry. Therefore, this chapter will concentrate on crushed stone as used in aggregates, with occasional reference to other uses or to chapters which discuss specific nonconstruction uses of crushed stone. Construction aggregates are hard, essentially inert materials suitable for being formed into a stable mass by the addition of cementing or binding materials that produce a concrete by compaction, or by natural weight to produce a road or foundation fill. Aggregates are usually from 80 to 100% of the material volume of the construction masses in which they are used. Conditions necessary for a rock deposit to be developed for construction crushed stone include: Quality-should pass rigid specifications for strength and durability; Quantity-adequate volume of rock is needed to have a production life of at least 10 years, preferably 20 or more years; Market-must have adequate market to support a new crushed stone operation; Transportation-transportation cost must be competitive for the intended market; Environmental-the impacts of mining, processing and transportation of crushed stone on the environment at or surrounding the mine site must be within acceptable limits; Permitability-mining, processing and transportation of crushed stone must usually be permitted by governing agency. The following discussion will touch upon all facets of crushed stone operations from the mineral deposit and its geology to technology, uses, economic factors and end with governmental regulations of mining crushed stone. The sections are not designed to answer all questions, but rather to be an introduction to the crushed stone industry. Where more information is required, The Aggregate Handbook by Barksdale (1991) is recommended as the best general source.

Jan 1, 1994

By A. D. Wunderlich

Providing a safe & secure environment for your employees and other company assets is absolutely necessary in our litigeous society. Security hardware is no different than computers or other technical equipment, in that new equipment is developed each year that makes older equipment obsolete. This presentation will help to explain how your existing security system and security procedures can be updated to meet industry standards without the expenditure of a great deal of money. If you are concerned about potential security problems and how to address these problems, this presentation is a must.

Jan 1, 1995

By B. Berg, J. Stephenson, J. Mansanti, C. Nyikos

"Intrepid Potash, Inc.’s Carlsbad East facility has refined sylvite and produced muriate of potash (MOP) since 1965. In addition to MOP, Intrepid Potash began recovering the mineral langbeinite from a mixed ore reserve in 2005. In 2011 a new langbeinite recovery process for the coarse (+850 micron) size fraction was constructed to enhance the overall langbeinite recovery. Based on the limited mixed ore reserve and an abundance of langbeinite ore reserves the transition of the East plant to a langbeinite only facility was targeted for 2021. Due to a decreasing grade of the mixed ore reserve, declining sales pricing, and high sylvite operating costs a strategic decision was made to accelerate this transition into 2016. To enable a successful transition, a fines recovery system needed to be developed, constructed and implemented. This paper describes the advancement of langbeinite processing at Intrepid Potash and the planning, development and successful execution of the transition to a langbeinite only operation. BACKGROUND Langbeinite (K2SO4·2MgSO4) is a double salt containing potassium sulfate (K2SO4) and magnesium sulfate (MgSO4). It is used as fertilizer and in the industry is described as Sulfate of Potash Magnesia. It is attractive as a specialty fertilizer and in addition to containing a ready source of a primary nutrient potassium, it also provides two secondary essential nutrients, magnesium and sulfur. It is especially attractive for chloride sensitive crops. Langbeinite has a specific gravity of 2.8, a Mohs hardness of 4.2, and is brittle thus very friable. It is the hardest of the saline minerals, and despite its relative softness on the Mohs scale can be very abrasive in process environments and in field applications, probably due to its conchoidal cleavage. Its solubility at 240 g/l is less than the solubility of sylvite (KCl) or halite (NaCl) and due to even slower relative dissolution kinetics washing with cold water has been a common practice for upgrading langbeinite ores. The solubilization/crystallization relationship for langbeinite is different from the majority of other evaporite minerals in that once langbeinite is solubilized it does not form langbeinite again. Instead it gives up one mole of magnesium sulfate, takes on various waters of hydration and precipitates out as either schoenite (K2SO4·MgSO4·6H2O) or leonite (K2SO4·MgSO4·4H2O) depending on temperature. Due to its partial solubility and phase transitions at its surface when exposed to moisture, there is strong cohesion between wetted particles; the resulting stickiness of the upgraded products can create significant materials handling issues unless processed in slurry form or at relatively low moisture levels. Langbeinite has been produced commercially from two locations, the Kalush and Stebnik regions in the Cartpathian Mountains of former Poland and now the Ukraine and from the Permian Basin in New Mexico (Garrett, 1996; Smith 1949). Current production is from two operators in the U.S., Mosaic and Intrepid Potash."

Jan 1, 2017

By T. Mudder

The objectives for closure of a hard rock mine include minimizing long term environmental liability, attaining regulatory compliance, and maintaining geotechnical stability, while closing as cost-effectively as possible. Proper planning for closure should come during the feasibility study, design and permitting phases, and during operations as updates. The lack of a proper or updated closure plan can result in severe environmental and economic consequences. Effective mine closure is the result of a combination of innovative concepts, long-term commitments, and multi-party cooperation. The purpose of this paper is to discuss concepts, commitments, and cooperation as they relate to an effective closure plan.

Jan 1, 1999

By B. C. Williams

The Bureau of Mines monitored the water quality in and near a copper/gold tailings impoundment. Samples were taken from the unsaturated %one. and dissolved concentrations of over ZO constituents were measured with respect to depth and moisture content, factors which influence oxygen content and sulfide oxidation. Samples from the unsaturated %one were drawn through a hypodermic needle sampler into individually evacuated vials fitted with septa, thus preventing oxygen contamination. Water quality was also monitored in the saturated tailings, underlying colluvial aquifer, and weathered andesite bedrock.

Jan 1, 1989

By James A. Martin

Evaluation and subsequent development of a quarry in east-central Missouri was based on a general but brief examination of outcrops and core from five (5) test holes. Neither core, outcrops, nor existing quarries in the general area gave any indication of potential major problems. In the third year of operation large areas of collapse rubble, consisting of green shale and large blocks of limestone and sandstone, were encountered. Their size and random distribution resulted in both blasting and quality control problems. By the fourth year of operation, production costs became prohibitive and the site was abandoned. Prior to dismantling the plant a geologic investigation, which included shallow seismic and resistivity surveys, was made of the unmined portion of the lease. The collapse dolines appear to be related to structure and predate development of the modern topography. Surface indications of these features are few. The seismic profiles were especially helpful in plotting their distribution. Geologic relationships and seismic data developed at this site are being related to similar suspect areas in Missouri and have been useful in their evaluation.

Jan 1, 1970

By D. Erik Spiller

Mineral processing technologies are being used in the environmental arena for remediation and secondary recovery. Comminution and/or scrubbing for liberation, coupled with separation of the liberated particles, is known as soil washing. Other metallurgical unit operations have found application in remediation and recycling: size classification, gravity concentration, flotation, magnetic and electrostatic separation, eddy current separation, and liquid/solid separation. This paper presents specific examples of the use of these technologies to clean up contaminated soils and plant residues, and to recycle valuable materials from waste streams.

Jan 1, 1993

By Giorgio Höfer-Öllinger, Peter Pointner, Manfred Stadlober

"SUMMARY Investigations from tunnel face are part of risk mitigation measures during the excavation works. With the tunnel equipment, percussion drillings of up to 30-40m can be achieved. Core drillings are state of art method for investigation exceeding 50m. At Koralm base tunnel, up to 270m deep percussion drillings were performed with drilling rigs and accompanied by an intensive investigation program. These investigations consisted of monitoring during the drilling, field tests (with packer, using the preventer, borehole imaging) and in laboratory. Percussion drillings are cheaper and save time of interruption of the excavation progress. INTRODUCTION As part of a proper risk management, horizontal advance drillings during excavation of underground works can be seen as state of art and meet wide acceptance. Core drillings, deep and shallow percussion drillings can be differed. The selection of the type of drilling, meanwhile, causes intensive discussions. On the one hand, only a core drilling allows a direct investigation of the rock mass expected during later excavation works. On the other hand core drillings are expensive in both cost and time – if there is no excavation progress during the investigation measures – in construction time. Percussion drillings can be performed as rapid investigation measure with the excavation equipment (“Jumbo”) allowing two dimensional image of the ground around the cross section. There is some limitation concerning a reasonable depth of approximately 30m and a borehole diameter of 76mm. The applications of preventer, packer or borehole imaging are hardly applicable. By use of a drilling rig depths of percussion drillings of several hundred meters can be achieved relative easily and there is less limitation of the borehole diameter. Installation of a preventer is possible, as well as packer tests and borehole measurements (imaging, gyroscope, borehole geophysics). The gap of information between core and percussion drilling cannot be closed completely, but it can be reduced substantially and sufficiently by combination of an intensive program of measurements and analysis accompanying the investigation works."

Jan 1, 2016

By R. K. Singhal

A sizable surface mining industry exists in Western Canada. There are the surface coal mines in the provinces of Alberta, British Columbia, and Saskatchewan producing the bulk of Canadian Coal. The two oil sands plants in Fort McMurray, Alberta producing synthetic crude oil are surface mining operations. Much of the metalliferous mining in British Columbia is carried out by open pit methods. This paper discusses the current surface mining methods in both of these industries with particular reference to Alberta. Issues relating to environmental impact assessment, mine reclamation and mine site closure have been dealt with.

Jan 1, 1995

By B. H. Johnston, B. N. Doyle

Introduction In 1983-84 Kidd Creek Mines Ltd. in Timmins, Ontario, started up the second commercial zinc pressure leaching plant based on the Sherritt Gordon Mines Ltd. direct pressure leach process. The first plant using this process was that of Cominco Ltd. at Trail, B.C. (Parker, 1981; Martin and Jankola, 1985). The Kidd Creek plant was constructed to take advantage of the extra capacity that the existing purification, cell house, and casting sections had in comparison to the roasters and acid plant. In addition, pressure leaching offered flexibility in other areas such as treatment of low grade concentrates. The process design package and the detailed design of the autoclave system was carried out by Sherritt. The detailed design for the rest of the plant was done by Cambrian Engineering Ltd. under the direction of Kidd Creek. The construction and commissioning of the plant has been described earlier (Johnston, 1983). This paper describes, briefly, the application of the direct pressure leaching process for zinc concentrates and the integration of the pressure leaching plant into the main zinc plant at Timmins. It discusses some of the startup problems and changes made to the plant. The damage following a fire inside the autoclave is also described. The subsequent repair and recommissioning of the autoclave has enabled Kidd Creek to demonstrate the originally sought advantages of pressure leaching and to take advantage of their extra cell house and casting capacity to produce more zinc. Process principles The development of the direct pressure sulphuric acid leach of zinc sulphide concentrate at temperatures above the melting point of sulphur and at elevated oxygen pressure has been described in detail in a number of papers (Martin and Jankola, 1985; Johnston, 1983; Veltman and Bolton, 1980; Kawulka et al., 1975; Veltman et al., 1977). The most significant aspect of the process is that sulphidic sulphur is converted to elemental sulphur in reactions that can be simply described as follows. ZnS + H2SO4 + 1/2 O2 ZnSO4 + S° + H2O (1) FeS + H2SO4 + 1/2 O2 FeSO4 + S° + H2O (2) The rates of these reactions increase with temperature. However, at temperatures above the melting point of sulphur, 12°C, the presence of a surface active agent is necessary to prevent the occlusion of the sulphide particles by elemental sulphur and the consequent termination of the leach. The zinc that is dissolved according to reaction (1), after purification of the zinc sulphate solution, is recovered by electrowinning. The iron that is put into solution according to reaction (2) is further oxidized to the ferric state and subsequently, as the acidity decreases, precipitates as hematite or as complex basic sulphates. MINERALS AND METALLURGICAL PROCESSING Examples of this are shown below. 2FeSO4 + H2SO4 +1/2O2 - Fe2(SO4)3 + H2O (3) Fe2(SO4)3 + 6H2O - Fe2O3.3H2O + 3H2SO4 (4) 3Fe2(SO4)3 + 14H2O - 2(H3O)Fe3(SO4)2(OH)6 + 5H2SO4 (5) (hydronium jarosite) The conventional zinc process involves concentrate roasting to produce zinc oxide and sulphur dioxide. The zinc oxide is leached in spent electrolyte and the sulphur dioxide is converted to sulphuric acid. The pressure leaching process can, therefore, be used to replace conventional concentrate roasting, sulphuric acid manufacture, and atmospheric leaching with one unit operation. Integration of pressure leaching into the Kidd Creek flowsheet A block flowsheet of the Kidd Creek zinc plant, with the new pressure leach plant integrated, is shown in Fig. 1. The original plant, which was constructed in 1972, is based on standard electrolytic zinc plant technology. Concentrates are dead roasted to remove sulphur. Sulphur dioxide is treated to produce sulphuric acid. Calcine is leached in two stages using cell-house electrolyte. Iron is precipitated as jarosite and solutions are purified to remove copper, cobalt, nickel, and cadmium to provide feed for a partially mechanized cell house. Zinc is plated from solution, and the resulting cathode is melted, cast, and sold (Johnston, 1983). The integration of the pressure leaching plant into the main zinc plant is relatively simple. As shown in Fig. 1, a fraction of the zinc concentrate and spent electrolyte are fed to the pressure leach autoclave, while part of the calcine from the roaster is used as a neutralizing agent in the oxidation step along with. the jarosite leach solution. The main exit stream from the pressure leaching plant is the slurry discharged from the oxidation step, consisting of neutral zinc sulphate solution, unreacted calcine, and precipitated iron oxides. This slurry is transferred to the neutral leach step in the main zinc plant. The leach residue from the pressure leaching step, consisting of basic iron sulphate and elemental sulphur, is washed and impounded along with the jarosite residue produced in the main plant.

Jan 1, 1987

By A. Simon, J. Weyer, J. Brune, V. Zhiteneva

"Reiche Zeche is a lead-zinc-silver deposit in Freiberg, Germany, that was mined for over 800 years. Since 1969, Reiche Zeche has been a teaching and research mine with numerous adits for dewatering large amounts of inflowing water. Infrequent metal water quality monitoring in the 1980-1990s and flooding of the mine in 2002 led to a lack of relevant data. New measurements were taken at different level adits and ore veins for comparison to historical values, revealing pH levels as low as 1.95, conductivity as high as 22000 µS/cm, and an overall trend towards less acidic waters. INTRODUCTION Reiche Zeche is part of the Himmelfahrt Fundgrube, a former iron ore mine in Freiberg, Germany, in the Erzgebirge mining region of Saxony. The polymetallic sulfide ore found in Freiberg was mined from 1168 to 1969, and though it is no longer producing ore, Reiche Zeche remains as a teaching and research mine for the Technische Universität Bergakademie Freiberg. The most important ore minerals mined were sphalerite, galena, pyrite, chalcopyrite, and silver, and important gangue minerals include calcite, fluorite, barite, siderite, and quartz (Zänker et al 2002). Over one thousand ore loads were mined from this region during operation, which was ceased in 1969 after the lower part of the 700 meter depth was flooded, leaving only the top 200 meters under the surface open for research and teaching. Mined materials from this region can be separated into high grade ore and waste rock. High grade ore, composed of pyrite, sphalerite, galena, chalcopyrite, and arsenopyrite, was brought to surface for smelting during mine operation, and spaces were backfilled with waste rock, which is the primary site of sulfide oxidation and acid mine drainage (Haubrich and Tichomirowa 2002). The waste rock includes remnants of ore from ore loss, veins which were too small to mine, or ore minerals within host rock. Waste rock is primarily composed of biotite gneiss, with sulfides including jarosite, gypsum, minor anglesite, scorodite, and sulfur (Haubrich and Tichomirowa 2002). When weathered, the gneiss forms clay minerals such as illite and kaolinite (Haubrich and Tichomirowa 2002)."

Jan 1, 2016

By D. McCarthy

This paper discusses the process involved in developing an optimum method of treating and removing heavy metals from water that have leached out from the native rock -prior to discharge back into the environment. Also designed into the system is a manner to stabilize the metals removed as a precipitate, so that they can be disposed of as a non-hazardous waste.

Jan 1, 1992

By Florence Munter

This paper provides a discussion of the various federal and state laws governing water quality as related to mining operations. The specific laws addressed are the Clean Water Act, and the Arizona Mined Land Reclamation Act. Topics that will be addressed are mine water and process water discharges, storm water discharges, pollution prevention, dredge and fill, spill prevention control and countermeasure plan, and surface water protection. Proposed changes to the laws and regulations will be discussed. Compliance strategies will be suggested to prevent potential noncompliance and enforcement.

Jan 1, 1996

By C. D. Elifrits, N. B. Aughenbaugh

Laboratory tests of samples of fine- grained, argellaceous rocks, commonly referred to as shales, have shown that various changes in their moisture content can be correlated with loss of strength. This reaction to a change of in situ conditions at abandoned mine sites when combined with the field relationships at locations where the predominant overburden material is fine-grained, argellaceous, and fractured provides a predictive tool for engineers dealing with subsidence problems. Such a tool should enable engineers to recognize areas that are prone to be affected by surface disturbing subsidence features.

Jan 1, 1987

By Steven Keim, Steven Stansfield, Kevin Andrews

Geotechnical, geological, and hydrogeological fieldwork and data collection for the mining industry is often conducted by younger, less-experienced staff members. In many cases, fieldwork personnel are recent college graduates or are otherwise relatively new to the mining industry. Due to busy schedules, staffing shortages, project budgets, and in some cases, poor management, new fieldwork hires often do not receive thorough training. In the past and the present, many workers in the mining industry learn(ed) by “doing.” While this is still considered to be the most practical approach and the easiest way for a company to determine the skill set of an employee, there is always some risk involved in the “feet to the fire” method. The reality is that field personnel are often collecting data on which major operational decisions will be made or on which regulators will base enforcement decisions. Inadequately trained or inexperienced field personnel may collect inaccurate data or fail to recognize key conditions that may influence decisions made by regulators, design engineers, mine managers, and corporate leaders. Even the best engineers may come to incorrect conclusions if they are starting with poor input data. Decisions based on inaccurate data often result in delays, budget issues, unsafe conditions, or even worse consequences. This paper provides numerous mining industry examples of incidences where inaccurately collected field information did, or could have, resulted in major adverse consequences. The paper also offers some simple approaches to minimizing the potential for such problems.

Jul 1, 2023

Maptek I-Site laser scanning expertise and software technology is being used to map the geology and layout of the deepest underground laboratory to be established in the U.S. The Deep Underground Science and Engineering Lab (DUSEL) in the former Homestake gold mine in Lead, SD, will provide for scientific studies in particle and nuclear physics, geology, hydrology, geo-engineering, biology and biochemistry. The project, funded by the National Science Foun¬dation (NSF), will allow geoscientists and engineers to research the behavior of subsurface rock, minerals, water and energy sources

Jan 1, 2010

By S. Behl, S. Mathur

The viability of physico-chemical purification methods such as selective, flocculation for the separation of two components having similar chemical compositions and the same crystal structure but different surface properties is demonstrated. A loss of selectivity was observed in a dolomite-dolomite mixture when polyethylene oxide (PEO) (five million molecular weight) was used us the flocculant. Heteroflocculation was minimized using a low molecular weight PEO (MW =105) as a site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at the 100% recovery level

Jan 1, 1996