Search Documents

By George Bárdossy

Most of the bauxite deposits in Europe belong to the karst type. They are located mainly ill Southern Europe along the Mediterranean Sea and in the Ural Mountains. Lateritic bauxite deposits occur on the Russian Platform, in Poland, Northern Ireland and in Turkey. Tikhvin-type deposits arc found on the Russian Platform. Bauxite formation in Europe started in the Middle Devonian. The main bauxite forming period was the Upper Cretaceous. Very few bauxites are younger than Eocene. Most deposits are covered by overburden of up to 1000 m. Prospecting is carried out by drilling. Several geophysical methods are used to detect the hidden deposits. Geostatistical methods were introduced in several countries for evaluation of the reserves and the geometry of the deposits. Data on bauxite production are given for 1982 and since the beginning of mining in Europe.

Jan 1, 1984

By A. Zutshi

Production of CO2 is an inevitable consequence of burning fossil fuels, with the only CO2 sequestration technique feasible in the immediate future being its injection in various geologic media. This paper discusses the factors that influence the injection, movement, and storage of CO2 into deep coal seams, while simultaneously increasing the production of methane. The results of a laboratory-scale study to evaluate the movement of CO2 in coal, its ability to displace methane, and the capacity of coal to retain CO2 are presented. The findings are compared with observations at one of the two field-scale pilot operations practicing CO2 injection in coal. Finally, the paper summarizes the research issues that require further investigation.

Jan 1, 2006

By P. T. Luckie

More efficient classification with a single hydrocyclone through equipment and/or operating design changes does not appear possible. However, improvement in classification efficiency by increasing the sharpness index and decreasing the apparent by-passing while changing the cut size is possible through proper staging of inefficient hydrocyclones. But feasible multistaging requires achieving the necessary material balances around the units. Because of the interactions among the units, these balances require extensive iterations. The final step before commerical installation should be a laboratory demonstration, in order to define the control algorithm required to maintain stability. However, eventually a sufficient knowledge base should be developed that will permit simulation in place of laboratory testing as well as the incorporation of a feed forward strategy.

Jan 1, 1989

By José A. Matar Ibañez

Geologic terranes in Argentina include potential mineralized environments from localized younger Precambrian cratonic outcrops through Paleozoic sequences, generally in the northwest or under younger cover, to the Mes[o] zoic-Cenozoic Andean Systems in western and southern Argentina. Argentina is self sufficient or nearly so in many metallic, nonmetallic, and energy commodities, and exploration in each of these categories is ongoing. Present production of precious metals (silver and gold) is important, and many recent discoveries of base metals, precious metals, alloy metals, and other mineral categories have been made. Economic trends, geologic environments, and commodity types important in actual exploration are described, and it is emphasized that extensive areas showing attractive alteration, geochemical, and geological anomalies, especially of porphyry, cordilleran vein, and epithermal characteristics, remain to be fully evaluated.

Jan 1, 1986

By James M. Prudden, Jon C. Sprague

Valdez Creek Mining Co. properties consist of multiple intersecting paleo-placer channels containing appreciable quantities of coarse gold. Reverse circulation drilling, combined with geophysics, is used for both exploration and development reserve determination. Classical drill-blast-load-haul open pit mining techniques used for the 22,000 cubic yard per day production schedule required modification to compensate for arctic winter operating conditions. High wall stability problems within the glacial sediment overburden necessitated developing multiple dewatering methods and variable pit slope designs to eliminate unstable pit wall conditions. Processing mine run fluvial gravels utilized a classical winter protected screening plant-sluice box recovery system enjoying high metallurgical recoveries and zero discharge tailings disposal.

Jan 1, 1987

By Ronald J. Thomas

Prior to 1974, bauxite-producing countries were poorly informed about important aspects of the bauxite/alumina/aluminium industry. This placed them at a disadvantage in negotiations over the development of the industry with interested parties. Since the formation of IBA, its member governments have acquired a fuller awareness of the structure and operation of the industry. The role of IBA is to enlarge the relevant information base of member governments, to act as a forum for the exchange of information on the industry and to form a focal point for multilateral discussions on problems in the industry with corporate interests and with governments of consuming countries.

Jan 1, 1984

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001

By C. Douglas Lee

This case study describes the work done at the University of Arizona on the development of a computer mine model for an irregularly shaped and spotty ore deposit. The purpose of the work was to develop techniques for modeling any highly irregular deposit, for which the regular 3D fixed block model is not well suited. The deposit contained complex geology consisting of sedimentary beds that had been faulted, thrusted, and intruded by igneous rocks (see Fig. 1). The physical dimensions of the modeled ore body were 1067 m (3500 ft) along the N-S direction and 914 m (3000 ft) along the E-W direction. Topographic relief in the modeled area was approximately 274 m (900 ft). The highest grade of ore was found near the surface with mineralization extending down to approximately 152 m (500 ft) below. Using a fixed bench height of 12 m (40 ft), the model required 25 levels with the highest elevation being at 1286 m (4220 ft). Fig. 2 shows a cross section of the developed computer model of the ore deposit. The particular modeling approach selected for this deposit was the 3D irregular block model.* This meant that only the dimension of bench height was fixed at 12 m (40 ft). Irregular size blocks in the form of polygons were adopted in the model to describe the ore zones and geologic contacts. The following sections of this chapter describe some of the techniques used in modeling.

Jan 1, 1979

By Steven J. Schatzel

A study was made of frictional ignitions in the underground coal mining industry from 1980 to 1992. The population of frictional ignitions was correlated to a variety of potential contributing factors including the mined coalbed, geographic location, mine production, methane gas emissions, and the type of mining equipment in use. The number of frictional ignitions reported in 1991 and 1992 surpassed the annual totals in all previous years included in the study. Most frictional ignitions occur during cutting operations at a coal face by a continuous miner. The average coal production of mines experiencing frictional ignitions is greater than the average of all underground coal mines throughout the survey period. Methane drainage may have produced a drop in the ratio of gas emissions to coal production (E/P) in mines experiencing frictional ignitions.

Jan 1, 1995

By E. S. Cheney

The sandstone-type uranium deposits of the Gas Hills occur in the arkosic, lower Eocene Wind River formation on the southern edge of the Wind River Basin. The d S34 values of pyrite cement associated with uranium mineralization are-significantly lighter than values for syngenetic-diagenetic pyrite nodules, therefore the H2S responsible for the precipitation of the epigenetic pyrite and uraninite was produced [t]epigenetically. These values are much lighter than the values of H2S from neighboring oil fields. The presence of biogenic pyrite in meta-igneous Precambrian cobbles indicates that these cobbles are not remnants of former; vein-type uranium deposits.

Jan 1, 1964

By Simon Wright, Roland Heersink

In the past, the center of most companies' e-initiatives has been on reduction of indirect costs, such as selling and procurement. Recently, e-commerce has moved its attention from back-office functions into manufacturing, in order to significantly reduce direct operating costs. This paper describes many of the Web-Powered Manufacturing initiatives being employed across various industries, and relates them to similar opportunities being started within the mining and mineral-processing sector. The following opportunities are enabled by Web-Powered Manufacturing: • Collaboration with outside experts to extend their pool of resources • Management of remote and distributed operations • Tie-in of small operations to a larger operation • Monitoring a position in a JV operated by a partner • Managing a plant located in someone else's facility • Having a chemical supplier manage his inventory in a customer's tanks • Having an equipment supplier remotely troubleshoot his equipment installed in a customer's site • Having an additive supplier provide remote pro-active. guidance in optimization of a customer's operation • Having software suppliers take responsibility for the results of their applications • Outsourcing software and systems support by providing remote access Details of one of these opportunities are described in this article, and the benefits captured using this approach and the technologies necessary to make them a reality are emphasized.

Jan 1, 2002

By S. K. Sharma

The Bureau of Mines has investigated the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters such as shear rate, polymer dosage, and polymer concentration on floc growth and to determine the applicability of a model in predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. Results show that the model, using GA as a tool to determine the unknown parameters, reproduces the experimental data with only reasonable accuracy and was relatively insensitive to the parameters. Results of the flocculation study showed that increases in polymer dosage had greater effect on the time required to reach the maximum floc size than on the floc size itself. It was also determined that, given all the aforementioned parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on the floc growth.

Jan 1, 1993

By J. Perlacia

Introduction The Bulk Handling Technology has already started its transformation to the Industry 4.0. Having some of the harshest working and environmental conditions of the industry, the possibility of remote analysis and maintenance of the components seems a perfect target to focus on. The most important and expensive tools have been adapted to the digital era during last years, from remotely controlled haul trucks to monitored conveyor belts. However, these big parts of the installations rely in smaller parts that have been left aside for a while, mainly due to the difficulty to adapt them to IoT (Internet of Things). The paradigmatic example is the lack of monitored rollers whereas all the other components of the conveyor belt installations (the belt itself, motors, drums etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stop of the whole conveyor, due to the possible damages to the belt, thus the implementation of an integral monitoring system of all the components of the conveyor is a must. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers, facing all the problems until its final installation in very different demanding conveyors, from the Australian extreme heat to the freezing cold Norway. All the tests done under actual working conditions, in real installations, have given a valuable knowledge in the identification of problems, their solution and the final advantages of a roller monitoring system. Background and Current State The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, an unexpected stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers long or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. As in many other industry products, the condition of rollers can be recognized measuring key parameters like the temperature of the bearings, the vibration level etc. The traditional way is to use the characteristic noise of a failing bearing, but this method usually implies to change several rollers because the maintenance team is not able to identify a single source of the noise. In recent years different attempts to measure the temperature of the bearings have been made, but the result is not accurate enough due to the proximity of the rollers in the idlers

Jan 1, 2019

By S. C. Suboleski, R. Zhao

A Simulation/Animation Model (SAM) with several unique features has been developed for continuous mining in room-and-pillar production systems. Initial cut data are generated by the program based on a short list of general section parameters, and is graphically displayed on the screen for checking and editing. This portion of the program includes several intelligent features. For example, a different cut sequence will be generated for uni-directional section ventilation than for bi-directional flow. Once the data are accepted, the entire simulation may be viewed in animation. Effectively, much of the data are checked visually by watching the actions of the mining equipment. Following the simulation, results are summarized as bar and pie charts, as well as printed output. In addition to the extensive use of graphics, the program contains several advances in simulation techniques as well.

Jan 1, 1993

By Gordon R. Luster

Mineral-processing plants commonly rely on homogenization and proportioning facilities to reduce the variability of incoming raw materials and to blend different materials together to satisfy quality specifications. To determine appropriate designs for these facilities, plant designers need information about the variability of the mined materials, measured as the materials enter the plant. But if the materials to be mined in the future differ greatly from those used in the past, only information extracted from exploratory drilling of the materials in the around may be available. Fortunately, useful information for plant design may still be obtained by combining simulated mineral deposits with simulations of likely mining procedures. The output of a mining simulation is a time series of simulated raw-material characteristics that should mimic the behavior of the real materials to be delivered to the plant in the future. This paper shows how conditional simulations of coregionalized ore grades can furnish information useful in the design of homogenization and proportioning systems.

Jan 1, 1986

By John E. Litz

Since the 1974 introduction of catalytic converters to automobiles in the United States, more than 150,000 kg (5,000,000 oz) of platinum, palladium, and rhodium have been used in the converters. An estimated 8 to 10 million converters are being used annually in the United States, each containing from $5 to $15 of PGM metals. In addition, use of converters is beginning in Europe which will significantly increase the quantity of PGM used. Two basic types of catalysts for converters are being used: pellet and monolithic. The pellets are small, discrete spheres or cylinders of gamma-alumina coated with platinum group metals, Figure 1. The monolithic are honeycombs of a cordierite, A13(Mg,Fe)2Si5AlO18, base coated with gamma-alumina and subsequently with platinum group metals, Figure 2. Pellet catalysts are being used by General Motors and American Motors; whereas Ford and Chrysler are using monolithic catalysts. The table below compares the PGM content and value of the catalysts.

Jan 1, 1986

Due Dilligance does not only lie in the statistics, but rather in the practical process aspects, which is the window to understanding the statistics.

Jan 1, 2005

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By Dae S. Young

The Disjunctive Kriging (DK) procedure was developed to estimate ore recovery figures within a deposit/ domain from limited diamond drill hole (DDH) core assay data taken at the exploration stage. Local recovery figures include minable ore tonnage and ore grades within relatively small areas such as stopes or small panels on a pit bench, for a given cut-off grade. The grade and tonnage should be computed based on the true selective mining units, that is, the average grade distribution of selective mining units within a panel. Local recovery figures are critical information for economic and engineering feasibility studies before mine development, as well as for short-term mine planning for operating mines. This kind of information can be provided only by non-linear geostatistical methods including DK and the Multivariate Gaussian Approach (MG) (Journel, 2, Parker, et al, 5).

Jan 1, 1982

By I. E. Odom

An electron optical and microprobe study was made to determine the physical and chemical nature of the silica minerals that occur as natural impurities in bentonite and montmorillonitic fuller&apos;s earth clay products (both granular and powder) and that occur in <10-µm dusts from plants that process these products. The purpose of the study was to determine if discrete "free" silica minerals, such as quartz, could be observed using SEM and EDS methods. No “free" silica minerals could be observed in the SEM images of the granular and powdered products, either among or on the surfaces of the particles. Also, no “free" silica could be identified by either SEM or EDS analyses of the dusts, even though quantitative X-ray diffraction analysis indicated that trace amounts of quartz occurred in all samples. It was determined that these quartz and other silica minerals were encapsulated or coated by montmorillonite. Vigorous washing, however, removed some of the clay coatings, so that small amounts of silica minerals could be seen by SEM and EDS analysis. It was found that all primary crystalline quartz grains in the bentonites have diagenetic overgrowths consisting of a mixture of montmorillonite, opaline silica and possibly microcrystalline quartz. Detrital quartz grains in the fuller&apos;s earth have thin diagenetic overgrowths of opaline silica, also containing montmorillonite. The clay encapsulation of the silica minerals in the products studied, as well as in the potentially respirable (<10-µm) dust produced during manufacturing of bentonite and montmorillonitic fuller&apos;s earth clay products, is considered to be an important factor influencing the potential health effects (e.g.. silicosis) of the contained silica. Even if clay dust containing silica should be inhaled, the montmorillonite encapsulating the quartz and other silica minerals would prevent direct contact of the silica with lung tissue. The clay encapsulation of quartz, as well as the highly hydroscopic nature of montmorillonite, may explain why not a single confirmed case of silicosis has ever been reported among plant workers in more than 65 years of production.

Jan 1, 1998