Search Documents

By Harry R. Price, Keith M. Swaffar

The Northeast Raw Water Tunnel transports untreated water to the Detroit Water and Sewerage Department's (DWSD) Northeast Water Plant where it is treated and distributed. The occurrence of a subsidence area which was attributed to the tunnel prompted the DWSD to have the tunnel investigated. After an extensive historical and geotechnical investigation, two access shafts were constructed along the alignment in the vicinity of the subsidence. Following completion of the shafts, the subsidence area was inspected in the wet prior to dewatering the tunnel. Upon the completion of dewatering, a dry inspection was performed. During the dry inspection, an area of significant distress was encountered where sand and silt were boiling into the tunnel along with large volumes of groundwater. This distressed area was located 800m (1/2 mile) north of the original subsidence area. The tunnel was immediately refilled with water and an emergency repair program was planned and implemented. As a result of the distressed nature of the secondary tunnel liner, dewatering of the tunnel could not be performed until the secondary liner and the surrounding soils were stabilized. This paper presents a case history of both the investigation and the repairs of the Northeast Raw Water Tunnel including the various grouting and unique tunnel stabilization methodologies which were utilized.

Jan 1, 1987

By V. Vesselinov, S. Orr

"Enhanced heap leaching - Part 1: Insights" (Orr, 2002), different flow and transport phenomena that could significantly reduce leaching recovery were investigated. The combination of such understanding with advanced flow and transport modeling establishes the link between cause and effect, thereby, directing operators to optimal design and construction of new heaps. Modeling of flow and transport in heaps could also point to a unique change in application method or rate that would maximize leaching enhancement of an existing heap under existing situation and leaching history. The use of such a model is cost effective in that it can simulate multiple scenarios of alternative leaching enhancement methods. By simulating a large number of irrigation scenarios, such a model can point to the optimal and/or the most promising alternatives for a particular heap. The authors' simulations concentrate on the effects of changes in application rates and heap design on changes in flow paths and enhanced leaching recovery. Based on such simulations, an intelligent control agent, such as Multiple Resolution Decision-Support System (MRDS) (Meystel and Albus, 2002), could build a new representation of the complex heap-leaching system. And, by learning from historical data and current information, it could provide optimal management of heap leaching and heap decommissioning.

Jan 1, 2003

By Norman E. Breslow, John A. Montgomery, Sanford W. Horstman

Reconstruction of historical exposures to silica dust is required in an ongoing cohort mortality study of workers in the diatomaceous earth (DE) industry. However, historical data were collected using three different sampling methods. This study was conducted to derive empirical quantitative relationships from linear regression equations between the three methods: standard impinger, total mass, and respirable mass. Dust from one diatomaceous earth processing plant was sampled simultaneously by all three methods. Results from 61 clusters of the three sampling devices indicate that the phcle size distribution of the dust varies with the two parent products sampled. baghouse product and main product. The relationships between particle counts and respirable mass are: Respirable mass (mg/m3) = 0.064 (mppd) impinger count for baghouse product dust, and respirable mass (mg/m3) = 0.018 (mppcf) impinger count for main product dust. The relationships between particle counts and total mass are: Total mass (mg/m3) = 0.837 (mppcf) impinger count for baghouse product, and total mass (mg/m3) = 1.21 (mppcf) for main product dust. In all four euuations, the intercept did not differ significantly from zero, and the correlation coefficients ranged from 0.90 to 0.95. Results are compared with data from four previously published studies.

Jan 1, 1991

By C. K. Lee

The influence of passageway fires on ventilation flows was investigated in three horizontal fire tunnel s: 1. a laboratory-scale fire tunnel network, 2. a small-scale fire-plume tunnel, and 3. a large- scale simulated mine gallery. Wood was used in the first and third tunnel and gas-burners were used in the second one to generate passageway fires. Experimental measurements included gas mass flow rate, velocity, temperature and pressure in the passageways and exhaust fans. The overall and local effects of the fires were investigated by comparing these measurements obtained before and during the fires. Results show that a passageway fire essentially increases the flow resistances of the passageways of a tunnel flow network by virtue of volatile fuel mass injection and high combustion temperatures. The ventilation air flow rate is consequently throttled to lower values than that before the fire. At severe throttling, reverse flow occurs. Conditions for reverse flow are characterized by two Froude numbers based on gas velocity and density upstream of the fire, and height of the passageway. The Froude numbers and the characteristics of the passageway fire are necessary to analyze mine ventilation/fire interaction and to predict mine ventilation patterns during fires.

Jan 1, 1980

By B. J. Arnold

Coal froth flotation cells typically receive little attention in coal preparation plants. They process only a small portion of the total coal feed (perhaps 5-1 0% of the total plant feed in the United States), they are viewed as a way to take the load off the refuse thickener, and their operation is not well-understood by cleaning plant operators. Operating parameters are set based on the equipment supplier information, and reagent dosages are set at the recommendation of the latest chemical vendor. The cells then operate day in and day out, recovering coal and producing a product that may not meet ash or sulfur specifications or that may be the wrong percent solids for downstream dewatering operations. If improvements can be made to this circuit, then the whole plant will benefit. Paying attention to rate and residence time and the wealth of data from the literature or from a series of targeted laboratory tests can give operators the key to improving the performance of froth flotation cells AND overall plant performance. This paper provides an overview of froth flotation rate and residence time data and gives practical suggestions for specifying and using laboratory tests to improve froth flotation performance. Suggestions for improving froth cell performance are also given based on available literature data.

Jan 1, 1999

By M. K. Gangal, E. D. Dainty

The paper describes the use of portable aerosol monitors in determining real-time concentrations of diesel soot and respirable total dust in dieselized mines. The field studies were conducted in a simulated diesel environment in the laboratory where no other type of dust was present, and in four underground mines with multi-diesel machine operations. Two packages for the real-time monitoring of diesel soot were prepared which included two types of aerosol monitors: a Miniram, model PDM-3, and a Sibata, model PDS-1. These monitors utilize the principle of light-scattering to measure the airborne mass concentration in the environment. The monitoring device results were compared against the Time-Weighted-Average (TWA) values produced by the gravimetric filter sampling method, permitting calibration factors to be determined for each field test. Both instrument packages provided comparable results. The instrument calibration factors varied for different tests, which may be due to different material composition, particle size distribution, density and shape of the aerosols. This approach for real-time determination of diesel soot is found to be simple, inexpensive and easy to use. More field tests for diesel soot determination and further research on size distribution of particulates in dieselized mines are required.

Jan 1, 1989

By Michael E. Salovich

The U. S. Department of Interior, Bureau of Mines (Bureau) has developed a prototype version of a computer application that combines hydrologic analysis with object-oriented graphics. This software is unique in that it presents analytic element analysis within an object-oriented CAD environment. Its user interface employs mouse handling, scrolling windows, dialog boxes, palettes, and pulldown menus. It can import scanned images of maps and overlay these images within the same window. This application was developed using object-oriented programming techniques. Several programming issues concerning graphics had to be resolved during development of this system. These include (1) how to represent hydrologic elements as graphical objects, (2) how to translate screen coordinates to map coordinates, (3) how to implement ?zooming? (changing the magnification level of a window), (4) how to overlay layers of images, and (5) how to import scanned images of maps. An object library was used to implement graphical user interface features such as scrolling windows and pull-down menus. Algorithms for CAD features such as map coordinate translation, zooming, and the layering of images were developed by Bureau researchers. The application has a modular source code structure and can be modified for use in other research applications.

Jan 1, 1992

By Edward S. Plotkin

The tunneling construction industry faces a new challenge in endeavoring to comply with the multitude of regulations and standards of the Occupational Safety and Health Administration and to work following accepted and experienced tunneling practices. Tunnel inspections appear to be gaining in priority. The national OSHA inspection activities reported for the year 1976 in the construction industry are as follows: 989 Inspections 45 As result of Accidents 186 As result of Complaints 605 General 153 Follow Up 34% Were found to be in compliance 714 Citations were Issued 1,825 Violations were found (201 of which were serious; 1573 were non-serious; 51 were imminent danger. There were no recorded failures to abate a violation in our industry.) The five general priorities by which a company would be scheduled for an inspection in descending order are: imminent danger situations, reports of fatal accidents or catastrophies, inspections in response to valid employee C( taints, inspections of work places covered by National Emphasis Program NEP, (OSHA's NEP has been designed to impact on any industry having a very high injury or illness rate) and finally random inspections of work places covered by OSHA. The following criteria in selecting companies for random inspections is used by OSHA.

Jan 1, 1979

By P. T. Brown

Denison Mines Limited, Canada's largest uranium producer located in Northern Ontario recently embarked upon an extensive development program that would allow them to substantially increase production and also meet the more stringent air quality standards established by the ministry of Natural Resources. To proceed with this program it was essential that the fresh air supply be greatly increased to the underground workings. A major portion of the mining area is located under Quirke Lake on the north limb of a syncline termed the Quirke Lake trough. The Denison engineers determined the most practical size and location for a proposed new fresh air shaft, eventually deciding to drive a 25 foot diameter shaft, 490 square feet in section for 1,800 feet long vertically. The shaft collar would be located on Roman Island, an island in Quirke Lake. A test hole was drilled from Roman Island to determine the ground through which the ventilation shaft would pass. This drill hole confirmed the location of the Quirke Lake over-thrust fault, a highly fractured water bearing zone 165 feet thick, approximately 800 feet below surface. Plans were made by Denison Mines Limited to seal and consolidate this ground when it was encountered by the shaft.

Jan 1, 1974

By Z. T. Bieniawsk, C. A. F. F. Santos

The effects of artificial weathering on the mechanical properties of the Loyalhanna sandstone have been investigated. Weathering was simulated in the laboratory by subjecting cylin- drical specimens of rock to alternate cycles of wetting and drying (in distilled water at 2O0C 2 5OC and in an electric oven at 105OC t 1°C, respectively). The total number of cycles was 100 and the geomechanical characteristics of the altered material were determined through uniaxial compressive and indirect tensile ("Brazilian") tests, with the determination of axial and trans- verse strains and monitoring of acoustic emission activity (rate and total event count). Moisture content and weight loss data were collected after each cycle and the mechanical parameters (unconfined strength, indirect tensile strength, young's modulus, Poisson's ratio, permanent set and AE/MS activity) were determined for unweathered specimens and after 10, 20, 50 and 100 cycles of wetting and drying. Hypotheses for the effect of weathering on the geomechanical properties of the Loyalhanna sandstone are proposed as reinforced by petrographic analyses carried out for the different stages of artificial weathering. A methodology for assessing the degree of physical weathering of rocks is proposed based on the number of wetting and drying cycles.

Jan 1, 1986

By Jake Beale, Joe Wickline, M. Van Dyke, Ted M. Klemetti

A longwall coal mine in southwestern Virginia mining the Pocahontas #3 Coal Seam experienced a history of mining-related seismic events. The events were never large enough to cause concern until three major events occurred recording 3.4, 4.3, and 3.4 ML in 2005, 2006, and 2007 respectively. Two of the seismic events generated an air blast which damaged stoppings which fueled a mine fire in 2005 and 2007. The mine responded to the events by narrowing the longwall widths, changing ventilation controls, installing a 7-sensor seismic system around the active panel, and creating a mining hazard map to avoid similar geology in the future. All of the actions taken have prevented seismic activity from impacting mining operations, but it did not prevent other large seismic events from occurring (Van Dyke et al., 2018). In 2016, another large seismic event, measured at 3.7 ML, occurred in the gob that was reported by the local media and recorded by the United States Geological Survey (USGS). While the event did not directly impact mining operations, mine management wanted to know where and under what conditions could large seismic events occur in the future. The National Institute for Occupational Safety and Health (NIOSH) became involved to help understand what conditions precipitated these events so that future mine design could more accurately assess seismic hazards and reduce the risk to mine worker safety. Researchers at NIOSH and mine management created a seismic forecasting map that combined three factors: (1) overburden thickness, (2) sandstone thickness, and (3) the expected caving height of the gob. The criteria were developed based on the geologic data the mine collected from core drilling, e-log analysis, and fiberscope observations. The forecast map was able to provide an accuracy of 72%–85% of events 1.5 ML or greater and 100% accuracy of events that were 3.0 ML or greater based on historical data. The seismic forecasting map was applied to the entire future mining area to show areas where seismic potential could be the greatest based on current mine design planning, ultimately improving the ability of the mine operator to assess the seismic hazards surrounding active and future mining areas (Van Dyke et al. 2018). Following this research, the seismic forecasting map was implemented into the mine’s hazard recognition program and is continuously updated and evaluated prior to mining each longwall panel. This paper will cover in more detail how the seismic and lithologic data was processed and how the mine implemented a new seismic mitigation program based on the forecasting results.

Apr 26, 2022

By C. C. Hatch

As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer and winter of 1975 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses and to permit study of alternative circuit configurations if desired. This paper describes the simulation methodology employed and presents the results of a computer study of the secondary crushing plant (1).

Jan 1, 1979

By M. J. Sapko

The Bureau conducted, through joint funding with the Colorado Mining Association, large scale oil shale rubble fire tests to investigate flotability characteristics and different methods of extinguishment. Ignition of large rubble piles was easily accomplished. Foam blankets could be used to control surface flames. The results of these large scale tests confirmed that water was effective in extinguishing deep seated oil shale fires but not particularly efficient. It took up to 1.7 times as much water to extinguish a fire as anticipated on the basis of a simple cooling model, assuming 100 pet utilization.

Jan 1, 1989

By Fred H. Lightner

The feasibility evaluation of the Borealis project of Houston International Minerals Corporation (HIMCO) was initiated in October of 1980. The operation of the Borealis Mine and heap leaching plant began in late 1981. In order to achieve the rapid development schedule several items were necessary: 1) Pre-planning of environmental requirements and early study of key issues. 2) Adoption of conservative design criteria. 3) Coordination and cooperation between HIMCO and regulatory agencies. 4) Adoption of specialized engineering and construction procedures. 5) Careful evaluation of owner project management philosophy.

Jan 1, 1982

By J. D. Miller

Pilot-scale tests indicate that effec¬tive concentration of fine gold from Colorado River sands can be achieved by flotation with the air-sparged hydrocyclone. The fine sands (55% minus 400 mesh and 0.01 opt*) from gravity concen¬tration were processed with a 5-cm air-sparged hydrocyclone (capacity -1.0 tph dry solids). Concentrate grades as high as 5.0 opt were produced in a single stage at a recovery of 75.0%. The separation efficiency was significantly better than that achieved in conventional batch flotation experiments.

Jan 1, 1985

By R. E. Vivas, J. Garcia

"INTRODUCTION Freeport-McMoRan is a leading international natural resources company that operates large, long-lived, geographically diverse assets with significant proven and probable reserves of copper, gold, molybdenum, cobalt, oil and natural gas. Freeport-McMoRan is the world’s largest publicly traded copper producer and largest producer of molybdenum. The Sierrita mine is an open pit truck and shovel operation from which copper and molybdenum are produced. An important key to Sierrita’s success lies in their ability to realize their plans in the field. In certain circumstances, the mine plans are not achieved, and the operation fails to meet its targets which is an issue revealed in reconciliation reports. This technical session discusses the methodologies and procedures used at Sierrita to monitor the implementation of the mine plans, measure the performance of the operation and reduce the variance between plan and actual. Ensuring the operation stays on target is vital so mine productivity and profitability can attain its maximum potential. PROJECT OVERVIEW The Sierrita mining complex is located in Pima County, approximately 20 miles southwest of Tucson, Arizona as shown in Figure 1. The first mining claims at Sierrita date back to the late 1800s while underground mining activities started in the early 1900s. However, open pit development of Sierrita began more than 50 years ago to become the modern mining complex it is today. In 2009, Freeport-McMoRan purchased the adjacent Twin Buttes copper mine, providing significant synergies in the Sierrita minerals district. This venture included the potential for expanded mining activities, operations growth for mining copper and molybdenum, and reclamation activity. It should be noted that in addition to copper and molybdenum, the Sierrita mine produces rhenium which is a rare and highly value metal. The ore deposit contains oxide and sulfide mineralization. The oxide ore is delivered to the leach process while the sulfide ore is routed to the crusher and mill circuit 4,700 jobs on Arizona’s economy Freeport-McMoRan partners with the communities near Sierrita to provide programs that contribute to their sustainability"

Jan 1, 2015

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By Richard R. Klimpel

This article introduces the basic definitions and philosophy behind process hazard evaluation procedures and the determination of risk as being a function of accident probabi1ity and accident consequence. The general concepts of good engineering practice and predictive hazard evaluation are discussed. The most commonly employed methods used in the processing industries are reviewed with an eye towards briefly presenting what each method offers as far as information, time and resources required, etc. Some initial references on the actual practical use of each technique in the processing industries are also given.

Jan 1, 1991

By Stephen Pogorski, Colin R. Phillips, Atika Khan

An optimized counting scheme for a mixture of radon daughters and thoron daughters typical of Ontario mines, developed in a previous study, was experimentally examined under mine conditions. The counting scheme requires a 10 minute sample and 5 1/2 hours counting instead of a 60 minute sample and more than 40 hours counting as required by a previous method. Taking into account the uncertainties associated with concentrations, flowrate and radioactive decay, the precision of the counting scheme was analyzed and found to be on average better than the 40 hour method.

Jan 1, 1981

By Yoginder P. Chugh, M. Silverman

Premining investigations involve the determination of roof, floor, and coal seam characteristics to delineate areas of troublesome ground control prior to development of a mine. Data obtained can be useful in mine design, equipment selection, estimation of face productivity, development of ground control plans and assessing ground control costs, and in conducting feasibility studies and financial analyses. This paper discusses 1) the causative factors associated with ground instability, 2) how useful data can be obtained for these factors during premining investigations, and 3) analysis techniques to delineate probable areas of ground instability.

Jan 1, 1982