Search Documents

By NORA Mining Sector Council

The National Occupational Research Agenda (NORA) is a partnership program to stimulate innovative research and workplace interventions. In combination with other initiatives, the products of this program are expected to reduce the occurrence of injuries and illnesses at work. Unveiled in 1996, NORA has become a research framework for the National Institute for Occupational Safety and Health (NIOSH) and the United States. Diverse parties collaborate to identify the most critical issues in workplace safety and health and develop research objectives for addressing those issues. NORA entered its third decade in 2016 with an enhanced structure. The 10 sectors formed for the second decade will continue to prioritize occupational safety and health research by major areas of the U.S. economy. In addition, NORA’s seven cross-sectors will continue to focus on the major health and safety issues affecting the U.S. working population. While NIOSH serves as the steward to move this effort forward, it is truly a national effort. NORA is carried out through councils comprised of members with many diverse interests that are developing and implementing research agendas for the occupational safety and health community over the third decade (2016-2026) of NORA. Councils address objectives through information exchange, partnership building, and enhanced dissemination and implementation of evidenced-based solutions. NORA groups industries into 10 sectors using North American Industry Classification System (NAICS) codes. The Mining Sector encompasses NAICS code grouping 21xxxx where “xxxx” represents the different subcodes of the mining “21” classification. Mining encompasses the extraction of solid mineral and mineral-like substances from their place in the Earth’s crust and supplies them to processing industries that produce economically valuable materials. It does not include oil and gas extraction. The Mine Safety and Health Administration, MSHA separates mining into coal, underground and surface, and metal and nonmetal, underground and surface.

Feb 1, 2024

By Williams K. C

This paper presents a brief account of the plant which has been developed at Port Pirie to recover, by vacuum distillation, the greater part of the zinc content of desilverized lead. The present plant is an experimental unit, which is run in conjunction with the normal refinery practice, but can be cut out of the circuit. It will shortly be dismantled and duplicate units will be built on the sites chosen for the final plant installation.The unit described here has treated flows of 16 to 37 tons per hour of desilverized lead, to recover 90 to 95 per cent of the zinc contained in it. It is not intended here to detail all aspects of the vacuum dezincing operation, nor the developments which precededthe adoption of this design. The essential features of the present plant will be described and, where these are peculiar to the present experimental location, the intended alteration for the final plant will also be mentioned. OUTLINE OF PLANT AND PROCESSLead issues from the continuous desilverizing kettle at about 350° C. containing about 0·57 per cent Zn. It is conveyed by a tiled launder to the preheater, where it is heated to 580-620° C.Hot lead from the preheater enters the vacuum vessel via a barometric leg. From a reservoir holding about 19 tons of lead it falls by gravity in a thin film exposed to high vacuum (20-50 microns)3 and leaves the vessel via a barometric leg, entering the lead pot. The lead leaves this pot at 540-560° C., containing 0·03 to 0·06 per cent Zn, which is removed, together with residual antimony of 0.02 to 0·06 per cent, by a separate final refining process.

Jan 1, 1956

By C M. Evans, D Thomas

Solid EnergyÆs Wangaloa open cast coal mine was operated between 1945 - 1989, and remained closed and disused until 2001 when SENZ initiated a mine rehabilitation programme. It is nearing the final stages of physical and environmental rehabilitation, aimed at creating an aesthetically pleasing and useful landscape. The final goals of these efforts are to produce an area, which has recreational and educational value. SENZÆs holistic approach to rehabilitation has been undertaken, treating the entire historical mine footprint instead of focusing only on those disturbed areas and the minimum range of issues just to meet with legal compliance. Rehabilitation at the site has included overburden modification with an emphasis on stability, removal and replacement of unhealthy and invasive plant species, and an AgLime amendment to alter soil pH conditions, which would support native plant species. To date, most ongoing activities relate to final planting and plant upkeep, and maintenance of the landform including ongoing erosion control, pest control, environmental monitoring, and research. Environmental quality concerns at the site may be treated by using a combination of methods, including regrading and capping of acid-generating pyrites, soil treatment with AgLime, and passive wetland treatment within existing water courses. Following major works, the mine site area may be opened to the public for recreational activities, interpretive displays on historical mining activities, and observation and appreciation for otherwise unseen geological features. SENZÆs holistic approach to reclamation, rather than treating minor issues, will result in the former mine site being transformed into an asset and the environmental and financial liability associated with the closed mine being discharged. Former mine sites can be turned from environmental liabilities with no recreational or public value (and potentially dangerous to life) into sites that can be safely used by the public for recreational and educational purposes.

Jan 1, 2006

By Dippenaar R, Evans T

Twin-roll continuous casting technology is rapidly approaching commercialisation. Fundamentally different than conventional continuous casting, heat transfer and hence solidification during twin-roll casting are governed by the interfacial melt/mould thermal resistance, as opposed to the resistance of the solidifying shell. Under these conditions the interface resistance is predominantly controlled by the melt/substrate wetting behaviour. The very early stages of melt/mould contact are characterised by highly transient heat transfer conditions. The overall melt cooling rates prior to the formation of the first solid are reported to be in the range of 1000 - 50000 K/s with melt undercoolings of up to 300 K. At the points of intimate melt/mould contact the thermal resistance is approaching zero, where cooling rates and undercooling much larger than those reported in the literature are probably occurring. Improved wetting will reduce the energy barrier for nucleation while at the same time increasing the cooling rate of the liquid. Since the overall nucleation rate is controlled both by the rate of cluster formation and the rate of atom transfer to the nucleus, a critical cooling rate will exist above which the nucleation rate is expected to be reduced. Under these conditions, it is possible that the first solid phase to form is a metastable glass which subsequently transforms into a crystalline phase. The implications on nucleation and early growth are also discussed.

Jan 1, 1999

By C. Richard Tinsley

INTRODUCTION The economic analysis (Chapter 3), the engineering studies (Chapter 10), the credit structure (and the consequential funding sources) - Chapter 11, and the overall feasibility structure for any venture are all directed to determining one major decision element: How much and how certain is the reward for taking these risks? Risk assessment is a surprisingly weak area of analysis and is usually addressed in a checklist fashion. It is much preferable to deal within a risk system so that the inevitable tradeoffs among risks are correctly made. DEFINITION The first step toward risk definition must be to ascertain all of the risks to which a project or a company is exposed; otherwise one will remain ignorant of the possibility of a financially crippling loss until it occurs. (Carter and Crockford, 1974). However, simply stating what "risk" is can lead to debate. For example, risk could be (adapted from Vaughan, 1982): -the chance of a loss - uncertainty of loss -possibility of loss - uncertainty -dispersion of actual from expected results - probability of an outcome different from the one expected - possibility of an occurrence of an undesirable contingency -a condition in which a possibility of a loss exists. For the minerals industry financier, the last definition is probably the most appropriate. However, from a mineral company's point of view the definition might well include the possibility of not achieving the expected financial return. RISK CLASSIFICATION Risk identification will be readily agreed as the all-important first step. There are five major "branches" of risk classification. These are: -Statistical -Modellers -Checklist -Project Financing -Insurance The Statistical set discovered probability theory and any risk discussion soon deteriorates into a mathematical jungle (Megill, 1977; Hartman, 1976; Reutlinger, 1970; and Pouliquen, 1970).Their use of terminology tells its own story: coin toss (binomial distribution), gamblers' ruin, delphi (oracle) techniques, monte-carlo simulations, random walks, etcetera. These techniques inadequately represent the judgements necessary in an increasingly complicated and interrelated world. The risk Modellers have turned to the computer to handle these inter-relationships but soon find barriers because of "simultaneity". Certainly the computer has its uses to conduct various analyses (marketed as "sensitivity" analyses) but very often one finds that this involves changing one or two variables at a time, all other things being equal. Unfortunately, in a modern and complex world all other things do not remain equal. The statisticians will, no doubt, jump to their own defence by citing this

Jan 1, 1985

By Wilhelm Knickmeyer, Johannes Henneke

PREFACE For about 1 year Bergbau-Forschung GmbH, central research institute of the German Coal Mining Industry, undertakes full size tests for waterjet assisted tunnel¬boring in German coal mines (Fig. 1). These tests are performed with a tunnelborer of 2.6 m diam in an upper [ ]

Jan 1, 1979

By J. R. Campbell

THE need for standardizing methods of arriving at definite conclusions regarding the cleanability of a given coal, and for measuring the performance of coal-cleaning equipment, is constantly increasing. Earlier notes by the author on this subject are amplified in this paper, because he believes that better preparation of bituminous coal is a partial solution of the coal operators' troubles. WASHABILITY STUDIES The term "washability" of coal was coined when washing was the universal method of separating coal from its impurities by utilizing their difference in specific gravity. This and analogous terms are still used in their broad sense although pneumatic or air separation is now used to clean coal. These terms are so used in this paper. Too much time or money, can hardly be spent on "feed surveys" to get a "picture" of the coal that is to be cleaned. There have been too many "rule of thumb" methods used. Screen analyses and "sink-and-float" tests on the raw coal enable the coal operator and washery man to predict within reasonable limits the results that may be expected from any efficient cleaning apparatus.

Jan 1, 1928

By R. Gallinger, B. Kelley

"In 1997, a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded that (1) that Canadian industry and Natural Resources Canada (NRCan) should fund a small secretariat in Ottawa to support technology transfer in Canada and, (2) that it was important for industry to continue the momentum of MEND on an international scale.The need for the International Network for Acid Prevention (INAP) was strongly endorsed by consultants, company, university, and government experts from Australia, Canada, and the United States who convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP’s members to promote the dissemination of successful practices, the identification of knowledge gaps, and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed assufficient justification for the formation of INAP.INAP was officially launched in October 1998, and is now an effective, industry-based initiative to globally coordinate research and development in the management of sulphide mine waste. Significant improvements in the management of sulphidic mine materials through knowledge sharing, research, and development of technology by INAP will reduce liability associated with acid drainage.This paper will explore the international efforts and activities of INAP."

Jan 1, 2005

By Kenneth R. Maser

This report describes the development of a system which modifies an existing fly ash-foam remote mine sealing technique to make it capable of impounding water in a fire zone. The modification involves blending equal quantities of fly ash and bentonite to form the bulk of the seal, and blending a thin layer of fly ash and Huron Regulated Set Portland Cement (RSPC) as a coating. The modification replaces the pure fly ash approach, but continues to use a froth foam topping to complete the seal. The modified material system is implemented with minimal complexity by adapting a "Y" connector to the existing delivery system. Each bulk hauler (fly ash and bentonite, or RSPC) will pump into one leg of the 'Y'; and the blending will be controlled by two pinch valves. The development effort has involved an evaluation of potential material systems by using small sample, quarter scale, and full head tests. The small sample tests measured the basic properties of a large number of selected material combinations. Property measurements included capillarity, permeability, shrinkage, and shear strength. As a result of these tests, particular combinations of fly ash-bentonite and fly ash-cement were selected for scale model testing in a 1 /4 scale test facility. These tests simulated, in a scaled manner, the water rise and total head which would be experienced by a seal. The tests indicated that shrinkage in the fly ash-cement combination would always result in leakage; whereas, fly ash-bentonite mixes were impervious to water.

Jan 1, 1974

By Hellsten KJ, Butt CRM

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By G. J. Hundman

Control of respirable dust produced by auger type continuous mining machines is normally attempted by water sprays from fixed nozzles mounted on the frame of the machine. In tests conducted under this contract, a 'wet auger' system was used, where the spray nozzles were mounted on the rotating auger itself. The tests were conducted at the Hunter mine of Smith and Stover Coal Company using a Jeffrey 1.00L auger miner. Operating the mining machine in the wet auger mode, it was found to produce 47 pct less respirable dust than when the fixed conventional sprays were used. On section dust levels were reduced too 3.5 mg/m3 which is equivalent to approximately 2.0 mg/m3 for a full shift portal to portal sample. The major difficulty that had to be overcome was the development of a simple reliable water transfer mechanism to get the water into the rotating augers. This was successfully achieved by the development of a water-through-the-shaft water system. This system can be retrofitted to existing machines and is available in kit form.

Jan 1, 1977

By A. D. S. Gillies

Diesel engine particulate matter pollution is a matter of concern currently in underground mines worldwide. A number of real-time Diesel Particulate Matter (DPM) monitors have been developed in recent years; two of these by the National Institute of Occupational Health and Safety (NIOSH) in the US. One, the D-PDM, is based on an adaption of the successful NIOSH?s Personal Dust Monitor (PDM) unit which is being taken up very successfully for mine respirable dust monitoring. The D-PDM measures all particulate matter within a sub-micron range as classified nominally at 0.8 micrometers by a purpose developed cyclone. The other, the FLIR Airtec, measures the Elemental Carbon (EC) component of DPM by a laser scattering approach. Both instruments have been evaluated underground in robustness and reliability testing in coal mines by the authors. Real time DPM monitors allow greater understanding of the sources and levels of DPM pollution in underground activities. They allow engineering evaluations to determine how conditions can be improved or mining personnel relocated to lower concentration levels. Studies are discussed that examine DPM concentrations from vehicles under varying ventilation conditions. Some of these concern tests undertaken during high activity longwall face moves. They focus on evaluating DPM during the various phases of the face Chock Shield moves. An initiative in some mines has been to limit the number of vehicles in the mining section or panel by the use of a Tag Board or Traffic Controller at the panel travel road entrance to manage exhaust DPM and gases. Diesel tags or tokens are used to control the number of vehicles entering a section or panel and so limit level of pollution. Summation of DPM levels from points monitored throughout a panel demonstrates increasing DPM levels from influence of additional equipment in series within the ventilation circuit. An alternative approach is to invest in underground continuous real-time monitoring of exhaust gases, DPM and section air quantity and integrate this information to determine whether an additional vehicle can enter without exceeding diesel target limit. This optimizes the access of diesel vehicles and replaces the existing manual tag board system. Real-time DPM monitoring allows the industry to pin-point high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. Identification of high DPM zones allows efficient modification of mine ventilation, operator positioning and other work practices to reduce underground miners? exposures.

Jan 1, 2012

By G. P. Halliwell, C. R. Austin

The investigation described in this paper deals with the development of high-temperature alloys of the Konel series over a considerable period of time at t,he Research Laboratories of the Westinghouse Electric and Manufacturing Co. The word ''Konel" has been coined to designate a class of alloys which are essentially nickel-cobalt-iron with other elements added, usually in small quantities. Most of these alloys contain titanium, usually about 2.5 per cent. The main consideration related to strength at high temperatures but the thermionic characteristics of the alloys was also of considerable importance. It is, however, with the mechanical properties at elevated temperatures that we are herein concerned. Much attention has also been devoted to their age-hardening characteristics. There is little need to stress the utilitarian aspect of this subject, as it has been discussed frequently. Alloys exhibiting superior properties at normal or elevated temperatures rapidly find many suitable applications. There may be some question, however, as to what constitutes a "superior alloy," or an alloy that may have good service possibilities at high temperatures. The problem is complex and various means have been employed to predict the useful life that may be expected of a material. In recent years the "creep limitJ' has been used as the best means of evaluation. Such tests necessarily are prolonged and hence collection of data is very slow. In a general survey of many alloys therefore the creep test is not desirable and recourse must be had to much shorter time tests in order more rapidly to select alloys which appear to show promise. For this reason the present survey has been made using the high-temperature tensile test and a bend test developed by Howard Scott.' In the tensile test the conditions have been standardized for all tests, so that values obtained are at least comparable, one alloy with another, although the absolute values recorded merely indicate the mechanical properties at the given temperature under a definite rate of loading.

Jan 1, 1932

By Hamid Maleki

In this paper, the authors present a review of data gathering programs and stress analyses for improving mine layout designs at BRL mines located near Paonia, Colorado. BRL and other companies have used both longwall and continuous miner methods for the extraction of the Upper D, Upper B, Lower B and C seams from the multiple-seam reserves in the North Fork Valley. Historic mining in the B and C seams has created stress footprints in the neighboring unmined seams compounded by stress transfer from recent longwall extraction in the Upper D Seam. Thus optimum positioning of workings in the remaining reserves requires careful collection of pertinent data and consideration of load transfer from previous workings through remnant abutment pillars. Based on long-term subsidence monitoring, underground mapping and stress analyses, we have confirmed initial load transfer analyses finding mild interactions between the UD and LB workings, and the mining conditions have proven to be good and manageable during the development stage of the LB Seam. This has been achieved through prudent mine planning, prudent positioning of the gateroads in multiple seam workings and support allocations.

Jan 1, 2007

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By M. Reza Saberi, T. Ted Miyake

Driven piles are a common tool in any engineer’s toolbox for supporting large structures over very soft ground, especially in high seismic risk zones. Challenges include achieving sufficient vertical and lateral load capacities within the constraints of pile spacing and geologic conditions. This was the case for a project in Orange County, California with a state-of-the-art, $180 million plant for biosolids processing, biogas management and energy recovery located in marshland next to an existing waste water treatment plant. The new construction for the Irvine Ranch Water District included a 70-foot (21 m) tall building and three closely spaced, 90-foot (27 m) high, 65-foot (20 m) diameter, egg-shaped steel digester tanks. The lower 35-feet (11 m) of the tanks were constructed below ground level. The site was underlain by up to 45 feet (14 m) of highly compressible peat and organic clays with standard penetration test (SPT) blows as low as 2 blows/ft (30 cm). Some of the peat layers had measured in-situ dry densities of less than 30 pcf (480 kg/m3) with moisture contents of over 250 percent. The soft clays and peat were underlain by a dense layer of sand and gravel at depth. Groundwater was very shallow. While nearby sites were designated by others as seismic site class “D”, this site was clearly class “F” (SF) which required site specific seismic hazard and time history analyses. Six recorded time histories were selected from the 1994 Northridge, 1989 Loma Prieta (California) and 1999 Chi Chi (Taiwan) earthquakes for the ground motion analysis considering the magnitude of the earthquake, distance to the source, characteristics of the earthquake source (i.e. type of fault displacement), peak ground acceleration, local site geology, station type (i.e. free-field or small structure stations), and spectral content that was similar to the period range of interest. Following ASCE’s Guideline Document 7-05, a site-specific horizontal acceleration response spectra (ARS) was developed for the maximum credible earthquake (MCE) associated with the site.

Jan 1, 2018

By André Pomerleau, Michel Grégoire, René del Villar

"The operation of industrial flotation columns requires the control of at least two variables, the interface position and the bias rate, by manipulation of some appropriate operating variables. Problems arise due to the reliability of existing methods of measuring the bias (i.e bias = tailings water - feed water), a situation which has often forced the industry to disregard this control loop. Moreover, when using such a measuring approach, the identification of the process dynamics is impossible. A second problem arises from the possible interaction between both control loops that might call for the use of a more complex multivariable control strategy.Recent work done at Lava1 University has demonstrated the feasibility of an independent sensor for bias, which models the relation between the conductivity profile across the interface and the bias value using a neural network algorithm. A 250 cm height, 5.25 cm diameter Plexiglas laboratory column was equipped with a series of conductivity electrodes in its uppermost part (across the interface) to measure both interface position and bias rate. Using such equipment, the flotation column dynamics were identified. The results thus obtained permitted the design and implementation of a distributed PI control strategy, where bias was associated to wash water rate and froth depth to tails rate. Both PI controllers were tuned using a frequency-response tuning method. Results of both identification and process control are presented and discussed.INTRODUCTIONFlotation columns are used for the separation of valuable minerals from a carrier gangue. Typically, this device is a tall (9 to 14 m height) cylinder (1 to 3 m in diameter) although other cross sectional shapes are also used. Finely ground ore is fed as a pulp at about 2 m from the top of the column, and pressurized air is introduced through a sparger at the bottom. If the pulp has been properly conditioned with adequate chemical reagents (collectors and modifiers), the valuable mineral particles falling by gravity will attach themselves to the rising air bubbles, and the air-particle aggregates will rise to the top of the column where they overflow as a stream called the concentrate. The gangue particles,, that do not attach to the air bubbles, fall down the column being withdrawn at its bottom in a stream called the tails.A particular characteristic of flotation columns is the addition of a fine spray of water at the top. As the water flows down through the froth zone, it washes out the entrained gangue particles from the mineralized bubbles, thus improving the quality of the concentrate recovered at the top. As a result of its cleaning action, this water stream is called the wash water and the upper zone, the cleaning zone. In order to ensure a downward flow of wash water, a proper water balance must be kept in the froth zone, otherwise the water added at the top might shortcircuit to the concentrate without performing any cleaning action. This net downward flow of water inside the froth zone is called the bias and represents an important operating variable of a flotation column."

Jan 1, 1999

By A. D. Storrie

An underground wet shotcrete trial was completed last year to determine the effectiveness of wet shotcrete as an alternative support mechanism to dry shotcrete in the kimberlite environment. The wet shotcrete was manufactured at the underground batch plants, transported to site using an agiecar and transferred to the shotcrete pump. The wet shotcrete is pumped to the nozzle where compressed air at 7 bar and an accelerator, Meyco SA 160, is added and enables the shotcrete to be placed successfully onto the tunnel wall. No tunnel guard was previously placed on the sidewall and hangingwall. Geotechnical testing indicates that the Grace fibre performed extremely well with the energy absorption tests at 7 kg/m3and 8kg/m3where both achieved over the mine requirement of 750joules. The Grace fibre and wet shotcrete mix also achieved a compressive strength in excess of 55 MPa, well above the 45 MPa requirement for Premier Mine. The recommended wet shotcrete mix design is therefore based upon: [Material/ CriteriaQuantity/m3Units ?Lafarge 42.5 Duratech500kg ?Condensed silica fume40kg ?Rayton Sand1.558Ton ?Delvocrete stabilizer 103.6litres ?Glenium 27CH5.4litres ?Meyco TCC 7355litres ?Water230litres ?Meyco SA16025litres ?Fibre8kg ?Cement/Water Ratio2.35? ?Water/Cement Ratio0.43? ?Flow615 mm] If the wet shotcrete system is implemented there is a potential for Premier Mine to make major savings. In South Africa there are two suitable wet shotcrete machines available for the mining industry, the Spreymec, manufactured by Tamrock and the Fermel/Meyco wet shotcrete machine. The Spreymec is a fully imported machine. The Fermel component is manufactured in South Africa and the Meyco shotcrete components are imported and supported by MBT (Master Builder Technologists) in South Africa. The Fermel/Meyco machine is assembled in South Africa. Premier Mine has allocated some R2, 100,000 towards the implementation of the wet shotcrete system. If implementation is successful there should be an internal rate of return gain of 76% with regard to this project.

Jan 1, 2001