Search Documents

By F. D. DeVaney

Metallurgists and coal-washing engineers have used heavy liquids for years in studying the characteristics of ores and coal. By such means true separations can be made between the various specific-gravity increments in the materials examined. To use of heavy liquids has permitted determination of the possible grades of tailings and concentrates by specific-gravity methods on any particular size, and therefore the size to which the ore must be crushed to free the valuable material. The simplicity of float-and-sink separation and the high degree of efficiency attained in the laboratory are factors that commend the method for commercial concentrations.

Jan 1, 1940

By F. F. Skiba, P. J. Root

A mathematical model has been used to investigate crossflow effects in a stratified reservoir during an idealized displacement process. A process in which one incompressible fluid displaces completely another incompressible fluid of the same density and viscosity was considered. The reservoir was assumed to be composed of homogeneous layers which are discrete but interconnected. Approximate five-spot flow geometry was simulated by arranging two pie-shaped cylindrical (two-dimensional) wedges in series. Some of the common production methods rely, for their effectiveness, on the fact that the formation consists of isolated strata. This is particularly true of selective plugging and single-zone production-injection methods. The effectiveness of these techniques for several cases in which adjacent strata are in communication has been evaluated. The usual production-injection schemes for fluid injection processes involve using the same completion interval in both the production and the injection wells. The efficiency of this, as well as alternative productioz-injection procedures has been examined for some cases involving communicating strata. INTRODUCTION The performance of many fluid injection projects is marred by early breakthrough and by production of a high percentage of the displacing phase after breakthrough. This channeling effect, if it occurs in reservoirs which have large permeability variations, is often explained on the basis of a model composed of discrete, isolated strata. Corrective or preventive measures based on this same model are also common. The behavior of stratified models has been the subject of considerable study. An excellent review of the early literature was given by Seba.1 Studies of the depletion performance have since been made for continuous, unrestricted communication between strata2-4 and for production from one permeable bed in continuous but restricted communication with an adjacent permeable bed.5,6 Model studies of displacement processes in stratified systems with crossflow also have been reprted.7-12 Finally, methods which account for crossflow have been developed for computing displacement behavior in stratified systems.13,14 Most methods for controlling or preventing channeling involve some change in the interval open to production and/or injection. Although many variations of the selective completion problem have been studied in regard to the depletion of a reservoir, little attention has been given to the behavior of a displacement process under similar conditions. Sebal used a resistance network model to study the performance of a process in which one incompressible fluid displaces an identical fluid from a linear, stratified reservoir. He investigated the possibility of improving the vertical coverage by limiting the completion interval of the production well. This investigation deals with techniques in which selective completion of the production and/or the injection wells is used in an attempt to control channeling. At one extreme, selective plugging and single-zone isolation (assuming perfect execution) should be successful if the reservoir is actually made up of independent strata. At the other extreme, they can hardly be expected to be successful if the channeling is caused by a mechanism in which stratification effects are negligible even though there are extreme variations in the formation permeability and/or the injectivity profile of the wells is not uniform. By contrast, it is difficult to anticipate the effect that the amount of communication between the beds of a stratified system will have on the efficiency of selective completion techniques. The objective of this study is the quantitative determination of the effect of communication on the behavior of some particular stratified systems which will at least lead to qualitative conclusions.

Jan 1, 1966

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains-- maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By Martin Smirlock

A novel instrumentation system has been developed which enables simple, quick, and accurate measurement of vehicular dynamics within low speed ranges. The system, consisting of a microwave transceiver and microprocessor data acquisition and reduction system, measures the deceleration dynamics of low-speed mining and construction equipment. It makes the basic measurement, calculates key parameters such as average deceleration, initial velocity, stopping distance, and brake system delay time, and produces autoscaled graphs of velocity, acceleration, and displacement versus time.

Jan 1, 1981

By F. J. Tozer

Canal communication between Lake Erie and Lake Ontario has been one of almost constant enlargement and reconstruction to meet the rapid growth of trade and commerce, and the consequent steady increase in the size of vessels plying the Great Lakes. The original canal was built by the Welland Canal Company. The first sod was turned in 1824 and the first vessel passed through in. 1829. There were 36 lift-locks, built of oak timber, 110 feet long and 22 feet wide, with a depth of water over the sills of 8 feet. The second canal, now known as the 'Old Welland Canal' was built by the Dominion of Canada (1842 to 1850). There were 26 masonry locks, 150 feet long, 26.5 feet wide and with a depth of water over the sills of 9 feet. The walls and banks were raised in 1853 to give a 10-foot draught. The third canal, known as the 'New Welland Canal, built by the Dominion of Canada, was started in June 1874 and the first boat passed through in the spring of 1882. There are 25 masonry lift-locks, 270 feet long, 45 feet wide and with a depth of water over the sills of 12 feet. The walls and banks were raised in 1891 to give a 14-foot draught. This is the canal in use at present.

Jan 1, 1926

By M. Lombardero, J. Garcia-Guinea, J. Taboada, B. W. Roberts

The structural, textural and mineralogical properties of the slate formations of NW Spain make it the most important district in the world for quarrying roofing slates. Over the past 10 years the introduction of new methods has increased yields from 2 to 13%. The main factors affecting quality are quartz grain size less than 75 micrometres, homogeneity of slaty cleavage and S0-S1 intersection angle, very low metamorphic grade, absence of secondary foliation, beds 10-12 m thick and low content of oxidisable Fe sulphides. The two main controls on fissility are lithology and deformation accompanied by metamorphism. The minimum natural block size should be 0.6 m3 but this volume can be reduced for modern cutting tools such as diamond wire, chain and circular saws. Structural analysis is crucial in exploration and quarrying, as shown by the prospecting methodology applied at Dominio de Truchas in central Spain and the computer analysis of rock mass discontinuities at Casaio quarry

Jun 19, 1905

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By E. R. Maize

[In %-port of Invcstiptionn 7452 ,g dcniing with roof ~wet,ent in the Cmcibla r~ine, rof&apos;erence .,as m.da to the f~ct tiwt timker decny war, bsing studied at tho tine of writing. Thic napor, written a3er completion of that ~tudy, describ~s t1l.e ~mrl&apos;: and sunlharizea the fiats obtained. Ifhen tlle stu* oi roof novement bras be,- at Cxcible tw igeas \%.ere a6-r;incsd. on decay of tiriber Q: scne of :he olficialr;: (I.) 9:la.t timber decay v:as unustmlly rapid in ,tho Ciuoiblc mins, ,m?. ((2) that timber coated with rock ri..~st deixiyad morrl mpirlly thnn those %hat vsrc not so coated. Thsx ::ore no records by which tkeso &apos;iaeas could &apos;L;e tertcc?, ard it cnpsarefi vise to make a limite6 in- vo3tiption, p~.rticu!.ai.ly of +.he effect of roc!< dusting on decny, as rock ductirg is nn importnnt mer-ns of ~rc-,rcnt?;~g cad-dust eql-osions. ]

Jan 1, 1941

Demonstrate the technical feasibility of using nontraditional, low-rank, coal-based fuels and new coal-based technologies for mineral and metallurgical applications. Approach A cooperative research effort was initiated between the Bureau of Mines, U.S. Department of Energy and the minerals industry to extend the application of the fixed-bed gasification process to low-rank Western coals. The research effort enabled cooperators to gain operating experience in the use of hot, raw producer gas for iron ore pellet induration and other high-temperature mineral processes. Researchers were able to gather data regarding the fundamental engineering aspects of the fixed-bed process and gas cleanup for a wide range of solid fuel properties. Applying Fixed-Bed Gasification As a prerequisite to gathering the data needed for the study, the Bureau of Mines designed and installed, at one of its laboratories, a 6.5-ft-diam. single stage, fixed-bed, air-blown atmospheric pressure gasifier. The gasifier was coupled with a hot, raw gas combustion system and iron ore pellet in. duration kiln. The gasifier is rated at 1.5 ton/h capacity of bituminous coal.

Jan 1, 1987

By M. E. Tyrrell

Lightweight basic refractories suitable for use in some sections of the all-basic furnace were developed. Potential advantages of such refractories are lower weight, improved resistance to thermal shock, and less tendency to spall off the working face. Plant trials in positions not subject to heavy loading or severe erosion seem warranted. Forsterite (2MgO.SiO2), stabilized dolomite (2Ca0?SiO2 + MgO), and chrome-spinel [(Fe,Mg)0?(Cr,Al) 031 refractories were fabricated using bubbles as the principal component in the brick mixtures. Bubbles were blown from melts of the basic raw materials as they were tapped from a conducting-hearth arc-resistance furnace. The bubbles were graded, bonded with synthetic Forsterite plus mineralizers, dry-pressed, and fired to temperatures of 1,600° C. or over in a gas-fired kiln. Refractory properties of the bubble brick were compared with those of insulating refractories made by burning combustibles out or dense brick mixtures. Lightweight refractories fabricated of bubbles were one-third lighter in weight than dense bricks of like materials. Their mechanical strength was satisfactory, and their resistance to thermal shock was excellent. In tolerance to open-hearth slag and in resistance to thermal shock, the chrome-spinel bubble bricks wore the best of the refractories tested. Basic refractories of the insulating type were about 40 percent lighter in weight than dense commercial refractories, but they were mechanically weak and not suitable for superduty service.

Jan 1, 1962

By Wils L. Cooley

Several aspects of coal mine safety-ground system operation are studied. Evaluations of two sophisticated ground-wire monitors are presented, along with a detailed report of development work on a modular ground-wire monitor. A portion of the report covers stray current flow in the safety-ground system, analyzing in detail conditions surrounding the generation of both dc and ac ground wire current. Considerable detail is provided concerning studies of mine ground beds. Additional progress is reported in the development of a. continuous ground-bed monitor, and new techniques are developed for the design of ground beds and their resistance measurement. New methods of accurately measuring electrical parameters of finite layered conducting structures are also reported. The effects of stray currents in ground beds is included. Touch-and step-potentials associated with mining equipment are analyzed, and methods are presented for determining earth voltage gradients around structures contacting earth. Instrumentation to determine gradients easily is suggested. Finally, an extensive effort is described dealing with lightning transients on open-pit coal mine ground systems. The nature of the transients, their expected frequency of occurrence, and the ways in which they damage equipment are analyzed in detail.

Jan 1, 1977

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By D. R. Wardrop, G. Walton

Paper presented at the UK minerals industry conference held in Leeds, UK, 3-5 April 1995. A description is given of the approach that has been taken to the design of the 550 000 000 t superquarry with a planned life of 60 years that is proposed for development. The quarry has been designed to replicate a corrie and a sea loch and will include excavated slopes more than 570 m high. The main geological and physical controls on the layout and the choice of development method are outlined. The operation phasing is presented and the geotechnical constraints on slope design and the feasibility of alternative quarry limits are discussed. Environmental considerations have been dominant in planning and the quarry has been specifically designed for closure

Jul 1, 1996

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

A glance at the accompanying table reveals that for the first time in many years the industrial minerals field did not post significant gains in production. Gypsum, cement, sand and gravel, and crushed stone production-which are very sensitive to construction industry performance-barely managed to stay even, or in fact, declined slightly. Even barite production, in spite of increased oil and gas drilling, was off 5% in 1979 from 1978. Domestic fluorspar production continued to decline while imports, primarily from Mexico, South Africa, and Spain, rose 11%. Worldwide production of iodine (which is used primarily as a catalyst, animal feed additive, and in ink and colorants, stabilizers, pharmaceuticals, photographic film, and disinfectants) grew about 9% on a worldwide basis-from 10.75 Tg to 11.16 Tg. This does not include US production. The two US producers increased demand as apparent domestic production increased about 5%. Increasing energy costs and the transportation situation have had a prohibitive effect on the industrial minerals field. The critical shortage of railroad cars, according to consultant Neil Johnson, is due to several factors: • High capital investment rind interest rates needed to build new equipment, • Accidents, obsolescence, and failure to repair equipment reduced car availability, •Reduction in some train schedules due to fuel economy, and •Increased turnaround time as a result of new safety regulations. Railroad rates have increased an average of 7% per year for the past 10 years. Last year&apos;s increases were about 11.1% due to fuel costs and surcharges. Truck shipments have increased their penetration in certain areas of the southeast because of the shortage of box cars and the producers&apos; demand for quick shipment. Some producers report a 15-20% increase in truck use. In the feldspar-mica area, which formerly made most shipments by rail, trucks are now used for about half the shipments. Marketing prices, as expected, increased due to higher costs for energy, power, labor, and supplies used in production. Estimated average price increases were about 10% which, in many cases, did not cover increased production costs. These factors-rising energy costs and the critical transportation situation-resulted in an unsatisfactory year for industrial minerals. Stanley J. Lefond Cnntrihuting Editor

Jan 5, 1980

By Lloyd A. Morley

The problems associated with the presence of organic materials and of water in explosion-proof enclosures used in high voltage, high capacity applications were examined through a literature search and theoretical reasoning. Information on volatilities is presented. The conclusion is reached that explosive pressures are significantly enhanced by inclusion of these materials.

Jan 1, 1976

This Bureau of Mines publication summarizes the industrial minerals industry of Idaho. It contains information on 119 principal deposits of 21 commodities in the State and describes the institutional and infrastructural factors affecting mineral development.

Jan 1, 1991

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By G. L. Gates

The waters used to waterflood the Wilmington oilfield were studied by the Bureau of Mines, in cooperation with the city of Long Beach, Calif. Increases in the pressure of the injection wells indicated that they were being plugged by materials suspended in the waters. This study was made to identify the suspended materials, determine their origin, and find methods of preventing their formation. The suspended oil-coated materials were iron sulfide, barium sulfate, calcium carbonate, clay, and sand (or silica). Results indicated that the sulfide, which was as high as 90 milligrams per liter, was the product of sulfate-reducing bacteria. The injection of ocean water increased the sulfate content of the waters in the petroleum reservoirs from 3 to 250 milligrams per liter, thereby furnishing sulfate for growth of the bacteria. The waters were supersaturated with barium sulfate. Laboratory tests showed that sulfide could be removed from the waters by adding iron at a cost of 1 to 2 mills per barrel. The solubility of iron sulfide and calcium orthophosphate in the injection waters was also determined.

Jan 1, 1975

By William M. Schafer

Forage plots were established on agricultural lands contaminated by acid mining waste. The acid produced through oxidation of pyrite and other sulfides caused elevated solubility and plant availability of copper, zinc, and arsenic which killed vegetation and polluted surface and groundwater. Soil amendments including agricultural lime (CaCO3), hydrated lime (Ca(OH)2), phosphorus, and organic matter were used to reduce the toxicity of metals. Several acid-tolerant grasses were used to vegetate the amended soils. Various soil extraction techniques were used to see which best correlated with vegetation performance. The extractions corresponded to three "forms" of metals in soil including soluble (water-saturation extract); plant-available/weakly adsorbed (DTPA extract); and total (HNO3/H202 extract). Of the extractants tested the DTPA levels appeared to correlate best with metal levels in plant tissue. The DTPA soil extractant serves as a useful tool in predicting potential phytotoxicity of mine waste materials.

Jan 1, 1989