Search Documents

By Diogo Tenório dos Santos

This property has been studied to characterize the strength a metallic material exhibits when it is machined so it can be regarded as its typical behaviour. As such, it may even be considered as an intrinsic material property. It is usually measured by an index called Coppini index, which is expressed by the ratio between the removed mass of a cutting tool caused by wear when it is used for machining and its initial one for a certain set of machining parameters. In this investigation, the tests were therefore conducted by an established set of parameters, namely feed rate, cutting and depth rates, in which the same wear mechanism took place in both ferrous alloys: AISI 4140 and AISI 316 steels. They were chosen based upon their increasing ordinary machinability indexes. The initial and final mass of the cutting tool were measured by an analytical scale with 0.01 mg precision. Cylindrical rods of 50-mm diameter were machined and the CI indexes showed a remarkable difference between them: 0.080 for the first steel and 0.049 for the second one, i.e., AISI 316 steel presented better machinability than the first one. It was then possible to conclude that this method presents good results in terms of both reproducibility and adequacy for machine shop conditions and it may be applied in a foreseeable future, mainly for metallic materials that have rather low machinability indices.

Jul 31, 2018

By M. A. Mekicha, M. B. de Rooij, C. Pelletier, D. T. A. Matthews

One of the main factors that reduce strip cleanliness are iron fines, which are formed due to the abrasive interactions of the roll surface and the strip in the roll bite during cold rolling. They can cause a problem in fouling of the cold rolling mill as well as downstream processes. It has been repeatedly observed that chrome plating the work roll improves strip cleanliness. In the present work, scratch tests and reciprocating sliding tests were carried out under lubricated conditions to explore the influence of chrome plating on iron fines formation. Scratch tests were conducted to study the influence of chrome plating on iron fines formation at single asperity scale due to its intrinsic property. Reciprocating sliding tests were performed to study the influence of chrome plating a rough surface on iron fines formation, taking into account the initial roughness. The scratches made using chrome plated pins showed lower friction, generated less iron fines and exhibited lower material transfer. Reciprocating sliding tests done using the uncoated pins showed galling at different sliding distances depending on the roughness of the pin. On the contrary, reciprocating sliding tests with the chrome plated pins exhibited no galling irrespective of the roughness.

Oct 1, 2019

By Leandro de Arruda Santos, Lorena Isabela de Oliveira Ribeiro, Jéssica Dornelas Silva, Pedro Damas Resende, João Victor Lucas Amim, Suzanny Cristina Soares Martins, Vicente Tadeu Lopes Buono

O objetivo do presente estudo foi avaliar a resistência à fadiga de duas ligas de NiTi diferentes sob condições de teste controladas por deformação a 25°C por meio de testes de fadiga por flexão rotativa. Além disso, as propriedades mecânicas, térmicas e estruturais dos fios foram caracterizadas por ensaios de DSC, DRX, MEV/EDS e tração. Os resultados revelaram que ambos os materiais são superelásticos à temperatura ambiente e, portanto apresentaram composição basicamente austenítica de sua matriz. Os resultados de ensaio de tração são condizentes com a caracterização térmica e estrutural, pois os materiais apresentam recuperação total de forma após ciclos de carga e descarga em tração. Ambos os materiais são ricos em titânio, um deles apresenta camada de óxido superficial enquanto o outro apresenta acabamento superficial. Apesar das propriedades similares a amostra 1 apresentou média de 77 ciclos até a falha, enquanto a amostra 2 resistiu a 1827 ciclos..

Oct 25, 2019

By Fernando Hernández Polanco

Transportation and handling metals and alloys from mills to consumption factories as well as dosing in conventional processes with ingots and scrap has always been considered a complicated activity with high operating costs. Several manufacturers of ferroalloys willing to solve these problems have chosen an alternative for their products that can be used to secure, during transport and dosage in the processes to making special steels, with more efficient consumption of ferroalloys. The trend for the production and sale of ferroalloys is to provide the product in the form of granules packed in bags or in bulk. In this paper we will show you how the granulation process was developed and rapidly adopted the ferroalloys industry as an effective solution to reduce operating costs, create cleaner and safer working environments.

Oct 30, 2017

By Edo Engel

Hot Blast Stove Technology has been developed to such an extent that low cost hot metal production for over 30 years without major repairs has become achievable, making the decision for a campaign length between 5 to over 30 years a design choice for the plant owner/operator. Some of the earlier examples of designs capable of such long campaign lengths are currently close to the 50th year of their running campaign. These examples are found especially in Europe and North America. Along the duration of these campaigns, repairs to subsystems such as burners, hot blast outlets etc. may be required. Depending on a plant’s up and down stream production capacities, the repairs may have to take place in the shortest possible time frame to minimize production loss. This article discusses an approach for intermediate repairs, executed while keeping the majority of the system at operating temperature.

Oct 30, 2017

By Jorge Madias

Pin holes as a surface defect, and blow holes as an inner defect, occur in billet / bloom / beam blank casting, particularly for Si-Mn killed steel cast with metering nozzle and oil lubrication. If they are present in abundance or have a large size, they may originate defects in the rolled products. Their characteristics, factors behind their formation, as well as usual processing conditions that promote their occurrence are discussed. Finally, the evolution of these defects during reheating and rolling is analyzed, with industrial examples.

Aug 16, 2017

By Claude Gaspard, Stefan Wahlund, Daniel Cavalier

A point of great importance in the cold rolling process for automotive sheet is the cleanliness of the strip, particularly critical in case of batch annealing with no degreasing line or inefficient cleaning before continuous lines. In this specific cases, pollution of the strip surface could be prohibitive when rolling in the early stands of tandem mill with conventional forged work rolls as ground. The strip cleanliness strongly deteriorates during rolling particularly with high roughness rolls: iron fines are generated at the strip surface due to friction and stick on the sheet. It is well known that chrome plating on ground forged rolls in the early stands improve the strip cleanliness. This paper summarizes the results of 3D surface roughness topography studies on forged work rolls, with and without chrome plating, combined with sheet cleanliness measurement during rolling. It shows that a well determined topography has to be obtained on the work rolls used in early stands in order to roll in the mixed lubrication regime, as described by the Stribeck curve, minimizing the friction coefficient and therefore optimizing the cleanliness of the rolled sheet. The main roll roughness parameters to take into account for that purpose are the roughness level Sa, and even more, the Kurtosis parameters Sk, Spk, Svk and Ssk. The ideal surface morphology promotes deep valleys to the detriment of peaks, leading to a roll surface capable of retaining/trapping oil in the valleys, while peaks are minimized, thus reducing the friction in the roll bite and the amount of iron fines produced. To achieve this objective, new grinding wheel technologies are currently developed, in dialogue with wheel manufacturers, to create such ideal morphology of roughness well adapted to HSS forged rolls.

Oct 1, 2019

By Marco A. Ramírez-Argáez

A 2D mathematical model was developed for the plasma arc welding process. Computational simulations based on mass and momentum conservation equations as well as Maxwell equations were performed by using the commercial software PHOENICS. The model predicts the electric characteristics of the arc column, flow patterns, temperature contours and electrical potential, by varying the composition of the cover gas, in this case, argon and nitrogen. It was found that an arc of nitrogen with respect to one of argon generates more intense jets, greater voltages, and lower temperatures in the arc column for welding arcs current of 150 A and 10 mm arc length.

Oct 30, 2017

By Adriane Lopes Mougo

Super duplex stainless steel presents a biphasic structure composed by ferrite and austenite with different characteristics and properties. In the micromilling process the cutting edge radius has similar dimensions to the grain size. The biphasic structure found in this material could influence on the cutting tool life and the surface integrity of the workpiece. Due to its low machinability, caused by high hardening level and low thermal conductivity, the process can produce built-up edge and high surface roughness (Ra). In this work it is performed an experimental study of the micromilling of super duplex UNS 32750 and the influence of the cutting speed (Vc) and feed per tooth (fz) on the surface integrity and tool wear. The design of experiments considered two levels and three replicates. Results indicate the increase of roughness for bigger feed per tooth, small influence of the cutting parameters on the burr formation. The tool presented flank wear after the experiments.

Aug 8, 2018

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita da zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetarem a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução da ZF foi 85%, para 100% CO, 1373K e 105 min, e 52%, para 50% CO, 1373K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373K durante 105 min. no caso da redução do EAFD

Aug 17, 2017

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita de zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetaram a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução foi 85%, para 100% CO, 1373 K e 105 min, e 52%, para 50% CO, 1373 K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373 K durante 105 min.

Aug 16, 2017

By Thorsten Müller

In order to increase the production of Advanced High Strength Steel (AHSS) as well as to fulfill the growing expectations of various industries served, steelmakers must have wide- ranging know-how in terms of plant technology, operation, processes, quality control and, last but not least, know-how for AHSS including certification procedures. MET/Con is highly focused on the production of coated AHSS with tensile strengths higher than 600 MPa. Common heating and cooling technologies are unable to handle high alloyed steel grades – pre-oxidation and rapid cooling technologies have been developed to face these new challenges. MET/CON and Drever International have the knowledge to produce newest steel grades with these technologies.

Jul 30, 2018

By Franco Gandin

With increasing demands for highly performing and at the same time efficient and running-costs saving vacuum-degassing equipment, dry mechanical pumps have been confirmed a proper choice to completely fulfill the expectations of steel-making companies worldwide. Regarding the production of both special carbon steel and stainless steel grades, the usage of mentioned pumps allowed reaching simultaneous remarkable results from different viewpoints in various Danieli worldwide installations (treating up to 200 t of liquid steel). As a matter of fact, in front of the replacement of a widely spread and renowned technology such as steamejector pumps with the recently developed technology embodied by the dry mechanical pumps, well-established metallurgical performances in terms of carbonhydrogen- nitrogen-sulphur removal have been repeatedly attained while meeting at the same time the client’s expectations concerning, for example, running-costs and push-button availability. Additionally, thanks to the very flexible, modular, redundant and maintenance-friendly equipment design, random problems occurring to the singular mechanical pumps can be easily solved without affecting the VD-VOD plant availability and metallurgical performance. With a particular regard to the VOD process, a very short overall process-time has been repeatedly performed (averagely less than 58min under-vacuum time at ChMP1) while guaranteeing the expected required quality of the final refined stainless steel. Moreover, in several VOD installations (ranging from 6 t up to 110 t of liquid steel) an efficient automatic process control such as dynamic pressure-regulation during oxygen-blowing has been attained thanks to the controllable variable-speed drives with which each mechanical pump is provided.

Aug 17, 2017

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

By Dusan Ilic

Conveyor system wear of belts and transfers attribute to a significant proportion of the maintenance costs and lost productive hours when handling hard abrasive ores at high unit rates typical of the iron ore industry. The recent growth phase has seen a rapid increase in mine and export capacity, with many new and upgraded plants operating at high throughput and utilisation. Subsequently, the industry has progressed to an optimisation phase, seeking to maximise production capacity and reduce maintenance costs with minimal capital spend. To support this, a programme of modifying designs was executed to improve conveyor transfer chute and belt life, which identified a need to challenge the industry practice for specification of designs to improve the functionality of the installed equipment. While acknowledging the importance of selecting the highest wear resistant materials for the intended application, this paper investigates design criteria related to decreasing conveyor transfer and belt wear. Of focus is a shift in the manner in which designs are specified, from specifications primarily governing geometrical constraints, to those meeting technical and functional requirements aimed at producing optimum geometry for a given set of material handling parameters. An assessment of transfer design criteria is presented.

Aug 17, 2017

By Steven G. Jansto

Nearly one third of the globally produced structural flat and long structural products are in the 0.11 to 0.16% carbon range. By definition, numerous steelmakers globally define this approximate carbon range as peritectic in their melting grade family within their organization. The metallurgical consequence is the result of numerous global structural specifications which allow carbon to wide carbon ranges resulting in quality issues. For example, such specifications as ASTM A588 set no minimum carbon and a 0.15 to 0.19%C maximum depending on the specific grade designated within the specification. This peritectic region is specifically challenging in production compared to less than 0.10%C because of solidification issues and a higher propensity for slab or billet cracking during continuous casting. During hot rolling, rejects and/or deviates are increased as well. The relative steelmaking operational cost of production is compared between peritectic and non-peritectic carbon compositions for a given specification.

Aug 17, 2017

By Qingwen Dai

The Marangoni effect is an important phenomenon where a surface tension gradient drives liquid towards high surface tension regions. Temperature gradient, evaporation, disparity of viscosity, and surface roughness and topography are all significant factors that can affect this thermo-capillary migration. The purpose of this study was to investigate the influence of micro-groove patterns on the migration of paraffin oil, and obtain a well-designed texture of micro-grooves to prevent the thermo-capillary migration. Patterns of micro-grooves with differing orientations and geometric parameters were fabricated on the surface of SUS 316 stainless steel substrates. Experiments on the migration behavior with different viscosities of paraffin oils were carried out various temperature gradients. The experimental phenomena indicated that the surface with the micro-grooves perpendicular or parallel to the temperature gradient have a strong impact on the migration performance of paraffin oil. Micro-grooves perpendicular to the temperature gradient exhibited extraordinary slower migration velocity than that of the parallel one. Width and depth of micro-grooves had an obvious influence on the behavior of temperature-driven migration and detail discussions on the effects of these geometric parameters were carried out.

Jul 31, 2018

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By Douglas Glenn Stalheim

Hot strip structural steel coil used in construction, engineering, transport, structural applications and other applications are widely used in yield strengths from 300 – 700 MPa. However, structural design engineers are now not only requiring various strength levels but also other mechanical properties, primarily good formability, toughness and weldability. To produce a balanced approach to a cost effective structural steel, hot strip coil requires an understanding of utilization of an optimized alloy composition designed for the layout/equipment capabilities of a given hot strip mill to produce the desired metallurgy for optimum mechanical property performance. The term “cost effective” does not just focus on alloy design, but also ease of overall processing from steelmaking, casting, rolling and cooling, stable mechanical properties with a statistically normal distribution, no downgrades/rejections and a product that the end user recognizes as being superior to others. The desired metallurgy is simply understanding what will be the optimum microstructure and cross sectional grain size/distribution needed to meet the mechanical property requirements. This paper is a follow up paper that previously described optimum base alloy designs along with steelmaking/casting processing considerations and will focus on proper reheating, rolling and cooling metallurgy/processing strategies to produce quality cost effective hot strip structural steel coil.

Aug 17, 2017

By Saul Garcia Hernandez

The research work objective is to study a new ladle shroud internal design to reduce the slag emulsification in the tundish during ladle transient periods. A 3D mathematical model of the tundish was created to solve the fundamental equations, a turbulence model, and a multiphase model. The results show that using a conventional ladle shroud, the fluid is delivered with an excessive amount of kinetic energy being dissipated inside the tundish bath, generating strong mixing flow patterns and entrapping a massive amount of slag. In the other hand, the proposed ladle shroud dissipates the kinetic energy before the fluid enters the tundish promoting less intense mixing patterns; thus, the amount of slag emulsification is reduced significantly. Consequently, if the internal design of the ladle shroud is able to dissipate the kinetic energy before the fluid enters the tundish, it shall be possible to reduce considerable the slag emulsification and the slag opening area.

Aug 17, 2017