Search Documents

By Enif Gutiérrez Guerrero

Inclusion deposition is still a standing problem in the continuous casting of steel since the deposition of alumina inclusions inside the SEN affects the productivity and the product quality. The present work studies the factors involved in the inclusion deposition at the nozzle and the effects of inertial, gravitational, buoyant, pressure gradient, and Saffman forces on the inclusion trajectories. The results show that the inclusions reaching the nozzle, only 30% get deposited along its walls mainly at the Upper Tundish Nozzle (UTN). This area of higher deposition is identified close to a low static pressure and a high turbulent kinetic energy dissipation zones where the effects of the gravitational and buoyant forces do not promote a significant inclusion radial movement since these are aligned with the direction of the flow stream lines. In contrast, in this zone, the Saffman force shows an important effect on the deposited inclusions, slowing down the inclusions in the vertical axis and increasing their radial movement.

Aug 17, 2017

By Stefan Stein, Jorge Davo, Adrian Villanueva, Abhay Kulkarni, Shane Hoff

Pellet sizing plays a key role in the productivity of the entire pelletization and subsequent induration processes, whereas uneven pellet sizing can increase the circulating load of the balling circuit inducing operational instability leading to production loses. The present work focuses in comparing the agglomeration kinetics, expressed as the number of pellets produced in a determined target size range, of different organic binder-bentonite binder systems. The batch experimental results show that the binder system has a great influence in the resulting pellet sizing, which could lead to advantages in terms of balling circuit efficiency and eventually operational de-bottlenecking.

Oct 1, 2019

By Zhi Zhang

The ever increasing demand of high performance rolls in the late finishing stands (F5 – F7) for hot strip mills (HSM) requires better product solutions from roll suppliers. Roll development activities never stop at Union Electric Åkers (UEÅ) in order to meet the requirement. The HYBRID STEEL, a new concept of roll materials especially for the late finishing stands in the HSM, is successfully developed in UEÅ. This paper reviewed the development of previous ICDP as well as enhanced ICDP (eICDP) roll materials, and, the novel HYBRID STEEL roll grade. Rolls manufactured by this new grade have been used in several European mills. A significant improvement over the enhanced ICDP rolls has been observed.

Oct 30, 2017

By Jorge Madias

Los hornos eléctricos de arco han sido motivo de una aplicación dinámica de nuevas tecnologías en lo que va de este siglo. La preparación de la chatarra y el uso de materiales de carga alternativos han dado lugar a la concepción de nuevos equipamientos y experiencias en todo el mundo. Surgen nuevos conceptos para el precalentamiento de la chatarra, superando las limitaciones de mantenimiento y ambientales de los conceptos iniciales y mejorando su performance energética. El aporte de energía química para la fusión supera sus límites año a año, requiriendo el desarrollo de equipamiento capaz de una acción rápida y precisa con grandes caudales de gases y sólidos inyectados. Existen nuevas herramientas para eliminar los riesgos de seguridad en la plataforma del horno, haciendo uso de sistemas de enfriamiento más seguros y duraderos, robots, automación de la operación del agujero de colado, y puertas de escoria controladas desde el púlpito.

Aug 17, 2017

By Glaydson Simões dos Reisr

Micropore organosilicas (MOs) were synthesized using methyl-phenyl-polysiloxane as precursor. The MOs were characterized using several analytical and functional techniques. The materials were assigned as micropores materials, with specific surface area up to 642 m2 g-1 and yield up to 72.55%. The adsorbents have hydrophobic surfaces and were used for removal of diclofenac from aqueous solutions. The adsorption kinetic and isothermal data were well described by the general order and Sips models, respectively. Diclofenac exhibited a better affinity than NM and the mechanism of adsorption suggested that hydrophobic groups play a key role in the adsorption process.

Aug 17, 2017

By José Divo Bressan

Present work examines material surface damage by cavitation erosion of metals or the wear phenomenon from water bubbles collapse near the metallic surface. Material surface damage by cavitation erosion is due to wear mechanisms of liquid micro-jets impingement and shock waves. Experimental cavitation in tap water was investigated, using the proposed new design of compact rotating disk equipment. In this device, a rotating disk with cavitation inducers and specimens fixed on it ran in tap water to provide cavitating flow at constant high speed of 47.9 m/s similar to service conditions in pumps and propellers. Two types of cavitation inducers in the rotating disk were investigated: through-holes and pins. Carburized cast iron, aluminum, brass and bronze specimens were tested in this device. The cavitation damage mechanisms were observed by scanning electron microscope. Surface damage in the specimens was measured by mass loss and plotted in graphs of mass loss versus running time. After 25 hours testing, the specimens surface showed pitting formation and mass loss. All specimens presented surface damage: pit diameter size was about 100 or 150 to 300 micron. In aluminum specimen, damages by burned pit formation and plastic deformation could be seen, however, the mass loss was lower than the expected, possibly due to alumina film formation. Present equipment had quite good test reproducibility when compared with results from literature.

Jul 31, 2018

By Lukas Pichler

The market trend of advanced high strength steel (AHSS) with demand for higher strength products is increasing continuously. The inline cooling technologies have established as the most powerful metallurgical tool to achieve these demands. However, the cooling capabilities of existing hot strip mills, plate and Steckel mills are often not adequate to generate high cooling rates and the cooling accuracy required for the production of AHSS. Hence there have been many developments for an intensive, highly flexible accurate homogeneous cooling technology. Considering the wide variety of strip and plate geometry, Primetals Technologies have developed Power Cooling Technology for strip and introduced MULPIC®4 Technology for the plate production. In this paper we shall discuss these enhanced technologies that provide the inline cooling requirement with examples from the recently commissioned machines.

Aug 17, 2017

By Ivan César Lopes Diniz

Stretcher Reducing Mill (SRM) is a mill used in production of tubes. It is composed with a set 24 of stands responsible to define the final outside diameter (OD) of tubes. External appearance is critical in this process even though this requirement has no effect on mechanical properties. For this reason, an investigation of external longitudinal marks mechanism is in progress using 6 Sigma methodology. This paper is a part of the investigation with focus on the rolls and its mechanical properties. Destructive tests were performed in the rolls and compared with the project. After a detailed investigation, it was concluded that rolls were out of hardness specification and the project was poor of information. A new supplier was developed (internal market) based on the new project and all requirements were achieved as demonstrated in this paper. A monopolistic market for this product in VSB (Vallourec Soluções Tubulares do Brasil) was eliminated. Concerning the effect on the external longitudinal marks, the new rolls developed within hardness range minimized the mechanism of wear on rolls surface and consequently on tubes surface. A collateral effect has been faced, but still better than external longitudinal marks on tubes surface. The quenched and tempered rolls are more sensitive for process variation, mainly linked with cooling system and temperature of tubes (mechanical resistance for deformation). Nevertheless, a new material has been aimed focusing on reduction of rolls breakage with good tenacity and affordable cost.

Oct 4, 2019

By Jorge Madias

La mayor parte de las máquinas de colada continua de palanquillas que utilizan buzas calibradas y lubricación con aceite se operan con alta velocidad de colada en secuencias largas, obteniendo alta productividad. Muchos de ellos todavía practican la inyección de aluminio en el molde, para desoxidar el acero líquido sin riesgo de obturación de las buzas. También es todavía usual la práctica de “pescar” la nata que se forma en el menisco. Las salpicaduras del chorro de cuchara contribuyen a la formación de chanchos en el repartidor, requiriendo el lanceo con oxígeno. Alternativamente, diversas plantas prefieren utilizar tubo de protección entre cuchara y repartidor y protección con gas inerte del chorro del repartidor al molde en todos los grados de acero colados con buza calibrada. Se hace una comparación entre ambas prácticas desde los puntos de vista de inversión, costo operativo, seguridad, productividad y calidad.

Jul 30, 2018

By Julián Andrés Ortiz González

This work presents a series of experiments of Fatigue Crack Growth (FCG), which are intended to provide evidence about the main parameter controlling this phenomenon, whereas still no agreement about this, since the Paris´ theory is based on the principle that FCG is controlled by the ?K and the Elber´s theory says that the driving force is ?Keff. For the development of the experiments, some DC(T) specimens were machined with two different thicknesses: 2 and 30 mm to perform FCG tests in plane stress and plane strain state, respectively. Besides this, all FCG tests were carried out with a constant ?K e Kmax, measuring the strain with a Strain-Gage bonded on the back face of the specimen and seven Strain-Gages located on the crack growth path. The data needed to measure the crack opening load, and the ?Keff, were collected through a program developed in Labview. Finally, the data post-processing was carried out based on the ASTM standards and several articles of recognized authors in this field, in order to compare the two positions with the experimental data, and this way conclude which is the most consistent theory with the observed behavior.

Aug 16, 2017

By Companhia Siderúrgica Nacional - CSN

Balanço Energético Global 2013

Jul 31, 2018

By Márcia Maria da Silva Monteiro Pereira

Tundish is the last reactor where significant metallurgical operations can still be done. Calcium aluminate slags are able to positively contribute to metallurgy considering oxide separation, protection against reoxidation and preclusion of resulphurisation. However, these are poor insulators. When using low melting point slags it is necessary to use another covering material. The deviation from saturation can be used as a measure of absorption capacity. By utilizing computerized construction of ternary and quaternary diagrams it is possible to compare different slags and to find proper slag compositions with reasonable capacity to dissolve inclusions. Objective of the present technical contribution is to evaluate tundish slag capacity to absorb inclusions, considering a particular tundish industrial slag and the changes in its chemical composition during continuous casting of steel. It was observed that slag composition changed during the continuous casting process; this variation is possibly related to interaction between the CaO-Al2O3 liquid slag and the rice hull ash layer which is used above it. Computational thermodynamics was used to determine activity of alumina dissolved in liquid slag; it was observed that the variation in slag composition did not change slag capacity to absorb inclusions, since precipitation of Al2O3 solid phases is not predicted.

Aug 17, 2017

By Henrique Silva Furtado

Concerning production of low phosphorus steel critical grades at ArcelorMittal Tubarão site, bottom blowing system plays a very important role. For those systems with independently controlled tuyeres, some non-uniform bottom blowing patterns seem to be promising in improving metal-slag mixing; however, based on computational fluid dynamics (CFD) results of ArcelorMittal Tubarão’s post oxygen bottom blowing, this may not be generalized. Also, from industrial trials it became clear that higher the bottom blowing flow rate, the closer were the end point P to the equilibrium. Despite this result an analysis of the apparent mass transfer coefficient has shown a week correlation with the classical power stir correlation suggesting a more complex kinetic limiting step for phosphorus removal.

Jul 30, 2018

By Günther Staudinger

Danieli Linz Technology has been honored at 4.1.2013 with the first contract for the exchange of a 350 t BOF converter for ArcelorMittal Poland Dabrowa Gornicza on a turnkey basis. This paper describes the new design features of this converter based on the development of a new Danieli converter suspension system. The issue was to install a new converter (incl. trunnion ring, suspension system and bearings) with maximum volume but keeping most of the existing equipment unchanged. So, the big tilting drives on both sides had to be reused and the existing foundation, pedestals as well as the bearing distance had to be maintained. Further on the welded coreequipment (vessel shell, trunnion ring, pedestals, slag shields, etc.) was manufactured in-house within the pressure vessel division of Danieli Thailand. Due to the huge dimensions of these parts the delivery had to take place in parts which had to be welded together on site under full production conditions of the steel plant. But also the erection had to be applied under this condition. Additionally the main support bearings, parts of the screening (doghouse) as well as an upgrade of the existing relining machine had to be delivered.

Jul 29, 2018

By Breno Totti Maia

Due to operational conditions and locations, BOF suffers variations in important parameters whose effects on the liquid bath are usually neglected. The present paper investigated two aspects: inner BOF pressure and oxygen temperature in the stagnant reservoir. The results have shown that oxygen temperature changes properties like density and velocity but has small influence on jet penetration. The BOF inner pressure has significant influence on jet penetration and creates a new challenge regarding nozzles dimensions considering overexpanding and underexpading jets.

Oct 30, 2017

By Fabiano Almir Barbosa, Eduardo Alves Machado, Felipe Ferreira Cajano, Bruno Rodrigues Henriques

Spring steels are usually classified as medium to high carbon low alloy steels with very high yield strength, enabling the part to return to its original shape regardless of significant bending or twisting. Despite the fact that plain carbon steels are suitable for small springs, larger and high performance springs usually requires alloy steels such as Cr-V or Si-Mn in order to achieve an even microstructure throughout the cross section. Clutch diaphragm spring is a high performance part that requires very good cleanliness and microstructure homogeneity, thus requiring an alloy steel. In this paper was studied, in an industrial scale, the process parameters and critical characteristics for the development of a Cr and V alloyed high carbon sheet steel for the production of clutch diaphragm spring. The steel was characterized throughout the entire process (casting, hot rolling, cold rolling + batch annealing and heat treated) using tensile test, hardness test, optical microscopy (OM) and scanning electron microscopy (SEM) to assess the mechanical and metallurgical properties of the studied steel. The results have shown the material’s microstructure evolution after each main stage of the process, from a ferrite-bainite/perlite based microstructure as hot band to fully spheroidized as cold-rolled/annealed and then fully martensitic as ready-to-use part.

Oct 1, 2019

By José Aparecido Pereira

The innovative methodology developed by the author allows the elaboration of an Angle Roll Pass Design based on the practical observations of the rolling process and applies mathematical criteria, using the Ekelund´s formula supported by Advanced Excel tools (Reach Goal, PROCV-PROCH, Macros) and AutoCad. The first step is the definition of the number of stands, roll dimensions, gear boxes reduction, initial stock, average reductions, spread factors, finishing speed and type of grooves. For each pass are calculated: bite angle, spread, section reduction, lost and gain of temperature, separating force, speed, torque and motor power. After these calculations and checking of the parameters, the program calculates the dimensions of the passes transforming the flat passes into shaped ones. With these dimensions it is possible to draw the grooves using AutoCad and check section reductions. This methodology was already used for the development of a new project and also to check the parameters of existing ones, with comparison of the results and has shown to be reliable in real and tested projects. It is an innovative process that is not available in known literature.

Oct 1, 2019

By Martin Chabicovsky, Milan Hnizdil

Emulsions are frequently used for the cooling and lubrication of working rolls during the cold rolling. The fact that the lubrication and cooling are not separable makes the optimization of both functionalities difficult. The higher emulsion temperature decreases the cooling efficiency compared to cold water. Heat transfer and fluid flow laboratory (Czech Republic), CRM (Belgium), Tata steel (Netherlands) and Henkel (Germany) cooperated on the increasing of a cooling efficiency during cold rolling. Part of this research was focused on an influence of the emulsion composition on a cooling intensity. The cooling efficiency was laboratory investigated. The stainless steel sample with thermocouple was heated and then it was cooled by a nozzle. Tests were performed with various emulsions and pure water. The heat transfer coefficient was computed from measured temperatures. The cooling intensity (heat transfer coefficient) of all tested emulsions was similar but an increase of the cooling intensity was found with water. Further various emulsions concentrations were tested. Results showed decreasing cooling intensity with increasing oil concentration. Adding additives therefore is thought to cause a noticeable decrease of the cooling intensity.

Oct 1, 2019

By Samuel Filgueiras Rodrigues, Clodualdo Aranas Jr., Gedeon Silva Reis, Eden Santos Silva, Fulvio Siciliano

When austenite is deformed above the Ae3 temperature, partial amount of it transforms dynamically into ferrite by a displacive mechanism. After unloading, it retransforms back into the stable austenite by a diffusional process. This influences the rolling load which decreases under isothermal condition or does not increase with decreasing temperature as rapidly as expected under cooling. Plate rolling simulations under isothermal and continuous cooling conditions were carried out on a 0.09 wt.% Nb X-70 steel. Pass strains of 0.2 were employed together with interpass times of 10 s, and 30 s for the cooling conditions and 0.3 with interval of 10 s at 900 °C for the isothermal experiments; strain rate of 1 s-1 was used during the simulations. The mean-flow-stress (MFS`s) behavior of both conditions indicates that dynamic transformation and dynamic recrystallization were taking place during straining. The critical strains for the initiation of dynamic transformation fell around 0.06 while the critical strain for DRX was 0.12. It has been shown that ferrite is formed due to the applied deformation of roughing passes and increases its volume fraction throughout the finishing rolling stage. Under cooling conditions, the ferrite formation is also favored as the temperature approaches the Ae3 line. Such ferrite forms when the driving force for dynamic transformation is higher than the total free energy barrier preventing its formation. This obstacle consists of the free energy difference between austenite and ferrite as well as the lattice dilatation work and shear accommodation work. The addition of Nb retards the retransformation of the ferrite into austenite. Moreover, holding times after rolling increases the amount of austenite available for microstructure control on subsequent stages. The dynamic transformation (DT) mechanism can be used to design improved rolling schedules

Oct 1, 2019

By Stanislas Mauuary

Price pressure is a real challenge on the stainless steel market. With market globalization, increase production capacity and exorbitant raw material, the margins are squeezing for stainless strip producers. Primetals Technologies offers a wide range of advanced technological solutions to secure the margins of our customers. Our solutions, implemented with professional project management, allow an optimum coil to market time, securing then the return on investment for the investor. Among the possible lever used to optimize the production route, one drastic step can be made to cut rolling time and cost by replacing the common 20-Hi mill stand reversing process by state of art high capacity X-HI® stands in continuous rolling line. Other source of savings can be implemented by integrated several process steps together (rolling, annealing, pickling, skin passing), achieving then savings on stocks and logistics while coil processing is reduced to fraction of hour. Additional solutions can also be implemented on the new, as well as existing line, like maintenance free solid state laser welder, skin-pass and tension levelers, in-line inspection system coupled with process and quality management system.

Aug 17, 2017