Search Documents

By P. R. Celmer, Leonard R. Weisberg

THE principle of fractional crystallization has been successfully used to prepare high-purity (99.999 pct) Ga. Hoffman and Scribnerl removed single crystals of gallium solidifying in a gallium melt, while Zimmerman2 grew single crystals from the melt by the Kyropolous technique. In contrast, attempts at purifying gallium by zone refining have been less successful. ichards, reported that despite the passage of 40 zones through a gallium ingot, there still remained 5 to 70 ppm each of Cu, Fe, Ca, Mg, Si, Al, and Ag. Previously, Detwiler and Fox4 detected only one impurity, Pb, segregating in zone-refined ingots. These surprising results prompted an investigation of the factors controlling impurity segregation in gallium. Possible reasons for this were insufficient diffusion of impurities in the melt; recontamination of the melt by its oxide film which is not affected by the passage of the zone; reaction of gallium with the boat; sudden freezing of gallium following supercooling, especially since gallium easily supercools to and trapping of impurities at grain boundaries. Impurity segregation tests were carried out by directionally freezing gallium using the Bridgman rnethd, modified in that the molten gallium is lowered out of a furnace into a slush of dry ice and trichloroethylene, thus minimizing supercooling. Since the gallium is contained vertically, the oxide film is in contact only with the tail end of the melt. It was found that Teflon makes an excellent crucible for gallium since it is quite pure, non-reactive, translucent, flexible, machinable, and is not wet by gallium. The gallium crystals could be grown at various speeds, and the melt could be vigorously stirred by a Teflon rod moving through the gallium in a vertical reciprocating fashion. Single crystals could be grown by placing a solid Teflon plug at the bottom of the melt drilled out in such a way to cause the solidifying gallium to follow a winding path. Thus, even if many crystals are originally nucleated, only one grain will predominate. The grain structure of the gallium crystals was revealed by an etchant composed of equal volumes of HC1, HNO3 and HF, diluted with water to half strength. Emission spectrographic analyses were carried out on samples removed from the front and tail ends of the resulting gallium ingots. Typical results of this study are summarized in Table I. The rate of freezing in all three cases was about 1 in. per hr. It can be seen that even though stirring of the melt does help, it is even more important to grow a single crystal of Ga in order to obtain good segregation of impurities. The effect of crys-tallinity on the segregation of impurities was previously observed6 in the directional freezing of germanium; however, in this case, the effect was much less pronounced. This dependence of impurity segregation on the crystalline perfection of Ga may be related to its thermal conductivity which is the most anisotropic of all metals.7 The anisotropic thermal conductivity can cause the solid-liquid interface to be nonuniform, thus leading to trapping of impurities during freeing, and therefore reduced segregation. In conclusion, it is indicated that zone refining of gallium would be more successful if seeding and similar precautions are taken to insure single crystal growth. The authors are indebted to Mr. H. H. Whitaker for the spectrographic analyses and to Drs. B. Abeles and F. D. Rosi for helpful advice and encouragement throughout the course of this work. This research was supported by the Electronics Research Directorate, Air Research and Development Command, under Contract No. AF33(616)-5029. REFERENCES 'J. 1. IToffmon and B. T. Scribrer: I. Research h'atl. Bur. Standards, 1935, "01. 15, p. 205. 'W. Zirnmerman: Science, 1954, vol. 119, p. 41. %J. L. Richards: Nature, 1956, vol. 117, p. 182. 'D. P. Detwiler and W. M. Fox: I. Metals, 1955, "01. 7, p. 205. 5P. W. Bridgman, Proc. Am. ilcod. Sci., 1925, vul. 60, pp. 305,385,423. "S. L1. Christian: private c ommuni cation. 'K. W. Powell: roy. Sac., 1951, vol. 209, p. 525. 'W. G. Pfann: Zone Re fining, p. 20. John Wiley and Sons, Inc., New York, L058.

Jan 1, 1962

By AIME AIME

INDUSTRIAL Pittsburgh, the center of the coal and iron and steel industry of the world, was host to the Coal Division at its Fall Meeting held there on Oct. 21 and 22 at the William Penn Hotel. The past year has witnessed remarkable progress in new methods of mining and burning of coal and many of the papers on the program discussed these developments. Nearly 100 had registered at the time of the first session on Wednesday morning and this number increased to 168 on Thursday. Owing to the large number of papers on the program, eighteen in all, it was necessary to hold group meetings on Thursday morning, with a capacity attendance at each meeting. . Chairman McAuliffe was on hand early Wednesday morning to open the meeting. George Otis Smith, representing President Lovejoy, came over from Cleveland where he attended the meetings of the Institute of Metals Division. Secretary Parsons arrived later from Cleveland and spent the whole morning with the executive committee of the Division. Doctor Smith, Secretary Parsons, and J. T. Breunich were the official representatives from Institute headquarters.

Jan 1, 1936

By R. C. Buehl, J. P. Morris

F. D. Richardson—The authors are to be congratulated on this further contribution to our knowledge of the thermodynamics of the interaction between sulphur and carbon and silicon in liquid iron. As the authors state, the influence of carbon and silicon on the activity coefficient of sulphur in liquid iron is clearly of great importance in the blast furnace, since it must cause a three to fourfold improvement in the partition of sulphur between slag and metal. The influence of increasing temperature in further increasing the activity coefficient of the sulphur in the metal in the blast furnace by increasing the carbon content is also of interest. This effect, however, is probably only part of the reason for the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing temperature. Other contributing factors are the lowering of the oxygen potential in the presence of carbon by increasing temperature and the probable increase in the activity coefficient of the lime in the slag for the same reason. The former of these effects, which works via the (CaO) + [S] = (CaS) + [O] equilibrium, might possibly account for a 70 pct improvement in the sulphur partition and the latter might give a further 50 pct improvement. C. Sherman—I would like to compliment the authors on their very careful research. If I may, I would like to show results of calculations on the carbon-sulphur-iron system similar to the ones that were shown in our paper for the silicon-sulphur-iron system. For Fe-S-C ternary system k=PHgs/PH2 x 1/(f1°) (f2°) (%S) where fs = sulphur activity coefficient fs' = fs for Fe-S system of equal pct S f3° = f2/f2 for Fe-S-C ternary system This same analysis has been used on other systems, but the results shown in fie.- 7 are for carbon and silicon. L. S. Darken—I would like to make two brief comments in addition to complimenting the authors on an apparently very precise and accurate investigation. The first is that the present work is in agreement with a calculation by Larsen and myself." Our calculation (much less precise than the present work) was based on: (1) Unpublished work on the sulphur content of molten iron (1.5 pct at 1500°C) in equilibrium with graphite and an iron sulphide slag; (2) the distribution coefficient of sulphur between slag and carbon-free liquid iron. We expressed the result in a form equivalent to log 7. = 0.18 [%C] which gives an activity coefficient (?s.) of sulphur only slightly higher than the authors find and certainly within the precision of the earlier work. My second comment concerns the correlation of the thermodynamic findings with atomistics. A rough pic- ture of the atomic arrangement in the liquid solution is rather easily conceived for this particular liquid solution containing iron, carbon, and sulphur. Carbon has a very much stronger affinity for iron than for sulphur. Hence we may conclude that a sulphur atom will but seldom be adjacent to a carbon atom—since this would be a position of high energy. From the metallic radii of iron and carbon we know that six iron atoms pack neatly around one carbon atom. Thus each carbon atom in retaining this shell of iron atoms (which latter may not be replaced by sulphur on account of the high energy requirement) decreases the available positions for each sulphur atom by six. Hence each atomic percent of carbon decreases the equilibrium sulphur content by 6 pct (of itself). Or, at low concentration each atomic percent of carbon increases the activity coefficient of sulphur by 6 pct. This is in good agreement with the observed increase (6 or 7 pct at low carbon content). It is indeed gratifying to find a case where, by such simple reasoning, quantitative agreement is found between precise data and the modern picture of the atomistics of the metallic state. J. P. Morris (authors' reply)—We would like to point out that there is an error in the equation on p. 322 of the paper. The third equation should read: ½S2 (gas) + H2 (gas) = H2S (gas) The authors wish to thank everyone for the interest they have shown in the paper. In regard to the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing the temperature, Dr. Richardson is correct in stating that the cause can be attributed only in part to the increase in activity coefficient of sulphur resulting from the rise in carbon plus silicon content of the metal with rise in temperature. However, this factor is probably an important one. The results of one experiment, performed since this report was written, indicate that at a constant temperature the addition of silicon to a melt saturated with carbon causes an increase in the activity coefficient of sulphur even though the carbon solubility is lowered. In this test, 2.5 pct silicon was added to a melt saturated with carbon and maintained at 1400°C. Although the carbon content dropped from 4.85 to 4.1 pct, the activity coefficient of sulphur was increased by about 20 pct.

Jan 1, 1951

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

MEASUREMENTS of the solubility of scandium in liquid cadmium from 349" to 606°C by Chasanov, Hunt, Johnson, and eder' led to the isolation and characterization of the intermetallic compound ScCQ. The solid phase found in equilibrium with a saturated solution of scandium in liquid cadmium above 422°C is ScCQ. The equilibrium solid phase below this temperature has not as yet been characterized. Hexagonal needles of ScCG were isolated from a 5 wt pct Sc alloy which had been ice-quenched from 500°C. Free cadmium was leached away from the intermetallic with saturated ammonium nitrate solution. The concentration of cadmium in successive leaches was followed polarographically and the leaching process was terminated when the rate of cadmium dissolution decreased markedly. Chemical analysis of the intermetallic thus isolated is as follows: 11.5 wt pct Sc and 88.3 wt pct Cd. The composition of ScCQ is 11.8 wt pct Sc and 88.2 wt pct Cd. X-ray diffraction powder photographs of ScCds taken in a 114.6-mm Debye-Scherrer camera with CuKa, radiation can be indexed on the basis of a hexagonal nit cell. Lattice coonstants are a. = 6.330 ± 0.001A to 6.324 i 0.001A and co = 4.853 i 0.001A. The a0 has a slight range with the lower value seemingly associated with the cadmium-rich terminus of the phase. With eight atoms in the unit cell the calculated intermetallic density is 7.54 g per cu cm; the density as determined by a liquid-displacement method is 7.7 g per cu cm. Powder-diffraction data for ScCQ are recorded in Table I. Stoichiometry, symmetry, unit-cell dimensions, and the number of atoms per unit cell indicate the MgsCd (D019) type structure for ScCQ; space group is D,&-P6,/mmc. Atomic coordinates are:

Jan 1, 1964

By Gerhard Derge, Harold Markus

The introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be dcscribed. For most of the additions, solutions containing 0.001 and 0.01 moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-l,ol~ate as follows: pH 0.1 M NaHC0............................................ 8.4 2 parts 0.1 M XaHCOr, 1 pa.rt 0.1 M NaZCO?................. 9.5 1 part 0.1 M NaHCOs, 2 parts 0.1 M iVa.,C03. ................ 10.0 0.1 M Na2C0............................................. 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves—sulphnte, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only -fuoridc, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also—phosphate, pcrborate, and chromate. Potential Measurements f The time-potential curves represntative of group 1 are shown in Fig. 1. These are the curves for 0.005 M sulphate ion and their similarity

Jan 1, 1939

By Harold Markus, Gerhard Derge

The introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be dcscribed. For most of the additions, solutions containing 0.001 and 0.01 moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-l,ol~ate as follows: pH 0.1 M NaHC0............................................ 8.4 2 parts 0.1 M XaHCOr, 1 pa.rt 0.1 M NaZCO?................. 9.5 1 part 0.1 M NaHCOs, 2 parts 0.1 M iVa.,C03. ................ 10.0 0.1 M Na2C0............................................. 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves—sulphnte, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only -fuoridc, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also—phosphate, pcrborate, and chromate. Potential Measurements f The time-potential curves represntative of group 1 are shown in Fig. 1. These are the curves for 0.005 M sulphate ion and their similarity

Jan 1, 1939

By AIME AIME

AMERICAN participation in the World Engineering Congress in Japan will be generous. Nearly seventy papers have been prepared and for- warded for printing and the A. I. M. E. is well represented in the list. At our San Francisco meeting four of these will be briefly reviewed by the authors for the benefit of those who are unable to go on to Tokyo. They constitute a group dealing with the present economic status as seen by engineers of the world's iron, coal, petroleum and non-ferrous metals. Messrs. Leith, Smith and Tryon, Requa, and Probert have written papers that constitute a notable series. Messrs. Jeffries, Sweetser and Kinney, and other Institute members have written papers dealing more closely with technologic progress. The latest list of delegates and members is printed below, names of A. I. M. E. members being set in italics.

Jan 1, 1929

By Lester A. Blackner

Discussion of the paper of LESTER A. BLACKNER, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 102, June, 1915, pp. 1249 to 1290. SIDNEY J. JENNINGS, New York, N. Y.-In the historical part of the development of the caving system discussed by Mr. Blackner, I notice the absence of one man's name, Charles Henroten. Mr. Henroten used the caving system in South Africa in the. Kimberly mines, and realized from his work there that ground would cave when properly prepared. I think it is due him that his name should be mentioned in connection with an exposition of this system in America.

Jan 12, 1915

By A. J. Griest, P. D. Frost, J. R. Doig

During the past 5 years, research directed toward the development of titanium alloys having improved strength-ductility relationships and heat treatability has been carried out at Battelle for the U. S. Air Force.1"3 In the course of this work, a method of heat treating ß-stabilized titanium alloys was developed which produced a wide range of useful properties.4 The heat treatment consisted of two steps: a) solution treating at temperatures in the a-ß phase region, and b) overaging at a lower temperature in the range 800°to 1100°F. Corollary to the alloy development work, research was conducted on the mechanism of the heat-treatment reaction. The investigations of Frost and co-workers on isothermal transformation in Ti-Cr5 and Ti-Mn8 alloys disclosed the existence of the transition phase, w, during the course of the decomposition of metastable ß phase. Subsequent work at Battelle7,8 'and at Case Institute by Brotzen and co-workerss further clarified the nature of the decomposition process. Beta decomposition was found to proceed by the following series of reactions: 1 2 3 4 a + Ti, My (in eutectoid systems). ßo, ßr, and ßU refer to ß phase of original, enriched, and ultimate alloy contents, respectively. Omega is a transition phase having a complex structure. 10-13 Step 4, of course, occurs only in ß-eutectoid systems. This paper presents data correlating transformation behavior with mechanical properties for the following alloys: Ti-8Mn, Ti-8Mn-2A1, Ti-4Mn-4A1, Ti-6Al-4V, and Ti-4Fe. The isothermal decomposition of ß in titanium-manganese alloys of similar composition has been investigated by Frost and coworkers8 and the effect of various annealing treatments on alloys in this system has been studied by Holden, Ogden, and Jaffee.14 The compositions Ti-8Mn-2Al, Ti-4Mn-4A1, and Ti-6A1-4V, were studied in the present work in an effort to define more clearly the effect of aluminum on the response to solution and aging treatments. Ogden, Holden, and Jaffee15 have invesitgated the effect of aluminum on the response of a similar alloy (Ti-8.8Mn-2.46A1) to annealing treatments, and Luini and Lee16 have made an exploratory investigation of the heat-treatability of the Ti-4Mn-4Al alloy. The Ti-4Fe alloy was studied as an example of a moderate1y active eutectoid system. Holden, Ogden, and Jaffee 17 have studied Ti-Fe alloys and have presented some hardness data for aging at 400°C for alloys of Ti-2.56, 5.01, and 7.35 iron after quenching from the a-ß field (750°C). EXPERIMENTAL PROCEDURES The experimental procedures generally used in the precipitation-hardening study are outlined in the following sections. Departures from these techniques are noted in the discussions of the individual alloys. Table I presents the nominal and actual compositions of the alloys studied, together with the swaging and rolling temperatures. In all cases, these temperatures were in the a-ß field and the microstructures consisted of an equiaxed a-ß mixture. Melting and Fabrication—Except for the commer-

Jan 1, 1960

By Sheldon P. Wimpfen

EVERYWHERE in mining circles the talk is of this new development of hard faced or insert bits which hints of many changes to come in mining practice and rock drill equipment. In the past fifteen years new equipment has appeared in rapid succession which brought one change after another in rock breaking practice. Detachable bits were an innovation which met with wide success. Blasthole diamond drilling has proven itself. Only recently, fusion piercing was announced as a possible solution to the problem of breaking taconite ores. For several years this interest in new methods has been growing and various experimental usages of tungsten carbides in rotary type rock drilling bits have been partially successful. American experts in rock drilling have been concerned with the subject for ten years but actual commercial practice was begun by European manufacturers and mining companies. At this time nearly every manufacturer of rock drilling bits is working on some type of an insert bit. On the Rand, European manufacturers are testing out various types of insert bits. The problems relating to rock drilling in South Africa vary greatly from ours. The bulk of the drilling there is limited to the 31/2-ft holes that are drilled for breaking the gold bearing reef ore. Rock drilling in most mines is far more diversified. Both drifting and ore breaking call for holes varying in length from 4 ft up to as much as 50 ft and more.

Jan 1, 1947

By David J. Mack

A SURVEY and critical appraisal of published information about Young's modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young's modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young's modulus. CALCULATION OF YOUNG'S MODULUS FROM THEORETICAL OR EMPIRICAL CONSIDERATIONS Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Southerland (1891), but Fessenden 41,42 made extensive calculations a few years later and arrived at the relationship: [2E = 78. 101 (_L V] where V is the atomic volume. In 1923, Peczalski,43 working from the same stand-point but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: [E=B(m) 2] where B is a constant of value about 8 • 10 7, p is density and m is atomic weight; the atomic volume, of course, being m/p. Portevin44 immediately pointed out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: [E _ KT'Vb] where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson.45 Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff. 50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs.46-48 He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium,

Jan 1, 1945

By N. I. Fisher, J. Shepherd

A rapid method of determining natural fracture trends in collieries has been developed. The method will yield information that is precise enough to permit fracture domain boundaries to be delineated in a coal seam. Instead of a survey of cleat trends in a colliery taking several man-weeks or even man-months, a reconnaissance survey can be carried out in only a few man-days. At each of a sequence of sampling sites along a traverse, five measurements of trend are recorded for each set of fracture directions. A sequential plot of the medians of each fracture set is then made manually underground or by a computer in the mine office. Changes in fracture pattern can be detected easily in colliery development work if a geologist visits advancing faces regularly, and forecasts can be made about the likelihood of forthcoming faults and dykes. A full description of this method is given in Shepherd and Fisher (1981). The concept of mapping fractures rapidly in a colliery is based on using a geological traverse (Compton, 1962), along which observations can be made at chosen, regular intervals. The technique has been widely used for surface mapping across outcrops and in follow-up work in photogeological studies (Hepworth and Kennerley, 1970). In these cases, the geologist surveys the traverse line as mapping proceeds. In a colliery, however, ready-made traverse lines already exist in panels and along main roadways, often in several directions. It is thus possible to traverse a colliery in different directions and record the fracture trends at intervals, generating a reconnaissance fracture map. This can also be done on a continuing basis as mine development takes place. Generally, a sampling traverse should be longer than 0.5 km with sampling sites at relatively close-spaced intervals along the traverse. For example, in room-and-pillar mines pillars are commonly formed on 40-m centers and the sampling sites can then be arranged at 20-m intervals [(Fig. 1)]. The sites might have to be closer together for mines known to have bad mining conditions. The predominant fracture trend is normally the face cleat and the subordinate trend is the butt cleat (McCulloch et al.. 1974). Various changes can occur in the cleat or joint pattern: the face and butt sets may disappear or an entirely new set or sets may appear. Therefore, it is best to record all prominent fracture sets. Sometimes there is only one; in other cases there may be as many as three or more. An odd number of measurements of each fracture set are made (generally five or more) to enable the median value to be determined easily. The median value can be plotted underground using graph paper or a computer plot can be made in the laboratory or mine office [(Fig. 2)]. The sequential linked median (SLIME) plot draws the median trend for each sampling site as a unit line segment. The segments from successive sampling sites can be connected together to form a long chain [(Fig. 2A)]. The needle plot, on the other hand, draws a straight line to represent the traverse and then plots out the median trend for each sampling site [(Fig. 2B)]. The SLIME plot is better for visual display, as it highlights small irregularities and gross changes in trend. However, some work is required to relate the individual segments to their site location along a traverse. In this respect, the needle plot is more convenient because each segment -can be plotted-at a point corresponding to its location. Also, there is precise match-up if needle plots of face and butt cleat are compared. A description and listing of the SLIME program is given by White et al. (1981). An example of the use of this method is given for Wallsend Borehole colliery in New South Wales (Australia) [(Fig. 2)], where domains II and IV are associated with mining hazards. Domain II is coincident with a normal fault of 2.6-m throw, and domain IV with a basic dyke 12 m thick. These hazards were approached driving in a southwesterly direction, and a pronounced change in trend of the cleat to a northwesterly direction occurred at a distance of approximately 45 m from each one. The northwestern joint trend is parallel to that of the dyke and fault, and it occurs at a higher frequency close to these structures. The association of a particular joint set with faults has been found elsewhere (Shepherd and Creasey, 1979). The two minor cleat direction changes within domain V are narrow joint zones that are less than 5 m wide. The fracture trends derived from a SLIME traverse can be verified by collecting larger quantities of data at selected sites, as shown in the balloon density (rose) plots depicted in [Fig. 2C]. We are grateful for the financial support provided by Thiess Bros. Pty. Ltd. and the National Energy Research, Development, and Demonstration Program administered by the Commonwealth Department of National Development and Energy. R.W. Miller Holdings Ltd. and Thiess Bros. Pty. Ltd. are thanked for their permission to publish data from their collieries.

Jan 1, 1982

By F. S. Pettit

The oxidation of Ni-3 to 25 wt pd Al alloys has been studied in 0. 1 atm of oxygen at temperatures between 900° and 1300°C. These alloys have been found to oxidize by three different mechanisms which depend on the temperature of- oxidation and the alloy composition. Two of the three mechanisms do not permit a continuous layer of Al,0, to be formed on the alloy surface and the oxidation rates are greater than that for pure nickel. The third mechanism results in the formation of an external A1203 scale and lke oxidation rates are about three orders of magnitude smaller than those for pure nickel. The minimum amount of aluminum required for the formation of external scales of A L,0, has been determined. NICKEL-base alloys are currently the main source of materials for use at elevated temperatures in gas turbine engines. These alloys are usually coated to obtain oxidation resistance. Coatings on nickel-base alloys are frequently formed by reaction of the alloy with aluminum whereby alloyed nickel aluminides are formed. The alloyed nickel aluminides provide protection to the nickel base alloy because external scales of A1203 (alumina) are formed during oxidation and mass transport through A120, is slow in comparison to mass transport through most other oxides. In view of the protective properties of A1203, it is important to know how much aluminum is required in these alloys in order to form external scales of AlzO,. The present paper is concerned with the oxidation kinetics and the oxidation mechanisms of Ni-A1 alloys and the minimum amount of aluminum required in these alloys for the formation of external scales of Alz03. THEORETICAL CONSIDERATIONS When a Ni-A1 alloy is heated in oxygen at elevated temperatures, the following reactions can take place on the surface of the alloy where the oxide phases are assumed to be virtually pure: These oxide phases are in the form of nuclei scattered over the surface of the alloy and, in view of their rapid formation, they need not be in equilibrium with the alloy. As the oxidation process continues, equilibrium between the alloy surface and the oxide phases is approached and the stability of the oxide nuclei is determined by the composition of the alloy at the alloy/oxide interface because of the following reactions: 3NiA1204 + 2A1 (alloy) = 4AlzO3 + 3Ni (alloy) [41 4Ni0 + 2Al (alloy) = NiA120, + 3Ni (alloy) [ 5 1 Application of the mass-action law to Eqs. [4J and [5J yields the following equilibrium conditions for these reactions: where aA1 and aNi are the activities of aluminum and nickel, are the standard free energies of formation of NiO, A1203, and NA1204, respectively, R is the gas constant, and T is the absolute temperature. If the composition of the alloy at the alloy/oxide interface is such that (akl/ahi) is greater than the equilibrium values defined by Eqs. [6] and [7], then Reactions (41 and [5] will go to the right as written. Conversely, if the alloy composition is such that the activity ratio (aLl,/aki) at the alloy/oxide interface is less than the equilibrium values, then Reactions [4] and [5] will proceed to the left. The equilibrium activity ratios in Eqs. [6] and 171 can be calculated since values for the standard free energies of formation of the oxide phases are available. Standard free energies of formation for NiO and A1203 have been tabulated by Elliott and ~leiser.' The standard free energy of formation for NiA1204 can be obtained from the data of Tretjakow and Schmalzried.' The results of these calculations are tabulated in Table I. Table I shows that the following inequality is valid over the temperature interval 900" to 1300°C: (Reaction [5]) (Reaction [4]) « 1and therefore the aluminum activity for these compositions can be taken as equal to the square root of the activity ratios (i.e., aNi = 1). If equilibrium is estab-

Jan 1, 1968

By Sidney H. Haughton

WHEN the white pioneers of the eighteenth and nineteenth centuries advanced from the coastal settlements of southern Africa into the interior of the subcontinent, they found it inhabited, more or less sparsely, by brown or black peoples mainly of pastoral habits but equipped with a fighting spirit and certain fighting weapons. Some of the tribes were smiths, others were miners and metallurgists; all used fuel, either industrially or domestically. Some of that fuel was wood, some cattle dung, and in some places the natives mined outcrop coal. Coal was first discovered by Europeans in Natal about 1840. After proper deliberation and after allowing due time for a consideration of all the implications, the Natal Government decided in 1881 (40 years after) to import an English expert to investigate and report on the discovery. Things then moved rapidly, and in what to a geologist is the remarkably short space of eight years, Natal collieries were producing at the rate of nearly 30,000 long tons per annum or 100 long tons per working day!

Jan 1, 1945

Jan 1, 1969

Jan 1, 1969

By C. M. Moncrief, B C. Craft

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By C. M. Moncrief

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By A. E. Zawadzki

A progress report is presented on the development of a process for the removal of sulfur dioxide from flue gases. Catalytic oxidation of the sulfur dioxide in flue gases, with the production of recoverable sulfuric acid, has been demonstrated to be technically feasible. Problems associated with the process are discussed. The need for an inexpensive and efficient process for controlling sulfur dioxide emissions from utility plant stacks has been accentuated by the ever-increasing public demand for elimination of all man-made air pollutants. I would like to describe the results of an investigation of the development of such a process; more important, I would like to present a discussion of the problems associated with the process which remain to be solved. The research work on the BCR catalytic gas phase oxidation process has been jointly sponsored by the Association of Edison Illuminating Cos., Edison Electric Inst. and Bituminous Coal Research, Inc., since 1958. However, work on SO2-pollution abatement was initiated by BCR in 1953. Tieman and Clymer,1 working with ozone and simulated flue gases, evaluated a gas phase oxidation process for removing SO2 from flue gases. Their experimental data indicated that the use of ozone to oxidize SO2 in flue gas concentrations, with subsequent recovery of H2SO4, did not appear to be economical due to the large ratio of ozone to sulfuric acid produced (2.6 to 1). The cost of the ozone would be 6 to 10 times the cost of sulfuric acid produced. As a result of the ozone study, work on a catalytic oxidation process was developed. The following reactions are the basis for the catalytic oxidation process Reaction [I] normally occurs in the combustion of sulfur-bearing fuels. At the high temperature found in the combustion chamber, 95% to 99% of the sulfur in the fuel is oxidized to SO2 and 1% to 5% is oxidized to SO3. The concentration of SO2 in the combustion gases depends on the combustion efficiency and the quantity of excess air used. A commonly used rule of thumb is 0.1 percent by volume SO2 in the flue gas for each 1% sulfur in the fuel. Reaction [2] proceeds at a wide range of temperatures. The rate of the reaction is rapid above l,000°F; however, the equilibrium conversion drops rapidly above this temperature. 2 Reaction [3] occurs rapidly to completion at temperatures below 400°F; above this temperature some SO3 exists in equilibrium with H2SO4. Complete dissociation of H2SO4 occurs above 650°F.3 The simplicity of the proposed process provided added incentive to the development and evaluation of the various component unit operations. The advantages of the process were considered to be as follows: 1) no raw materials were required, 2) the unit operations were not radically new; and 3) a salable product, sulfuric acid, would be produced. The successful development of the process was contingent upon the solution of several major problems: 1) The development of a catalyst which would provide high catalytic activity at reasonable conditions of gas flow and temperature without causing an unacceptable increase in pressure drop. 2) The development of a high temperature dust collection system to provide clean flue gases to the catalytic reactor. 3) The complete recovery of the sulfuric acid produced in the process; the effluent gas must contain less than 20 ppm by volume of sulfuric acid. As of this date, the complete solution to these problems has not been achieved. EXPERIMENTAL Catalyst Development: The use of platinum and vanadium catalysts for the production of sulfuric acid by the treatment of dry gases containing 5% to 20% by volume sulfur dioxide has been known for many years. The application of the basic idea of catalytic oxidation of sulfur dioxide in flue gas concentrations was

Jan 1, 1965

By W. E. Anderson, T. M. Brady

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at 13 mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing bucket sizes ranging from 30 to 220 cu yd (23 to 168 m), were documented. Draglines at large US surface coal mines can be represented as 120 machines having 60-cu yd (46-m3) buckets, moving 1.8 X 109 cu yd (1.4 x 109 m3) of overburden during 6650 hours of productive availability per year. Based on the limited field study, the calculated downtime resulting from rope-related causes averages 105.6 hours per year for each typical 60-cu yd (43-m3) dragline. The total loss in production from this source alone is thereby estimated at about 25 x 106 cu yd (19 x 106 m3) annually. Although study findings did not reveal anything about dragline rope life that wasn't known or practiced by one operator or another, most operators can expect improved rope life by periodic review of their practices and by adopting one or more life-improvement measures employed at other sites. Since rope productivity was found to vary by a factor of five among the sites studied, considerable improved average performance is possible. As little as 10% overall improvement would increase national productivity by 2 million cu yd (1.5 X 106 m3) of solid overburden removal. Associated savings in rope costs would be some $2 million annually, plus a large reduction of labor-related expenses. This report outlines preliminary findings which may prove useful to many operators in extending wire rope life. Some of these modifications or adjustments in maintenance/operating practices would not require capital investment. During the field survey, no company was found which had tried cost reductions by using presocketed dump ropes, or dump rope sheaves that opened like a snatch block, so these are suggested as possible improvements requiring modest capital input. Data Acquisition During the field visits, mine operators provided rope life information about their machines. Some of the rope life data consisted of gross averages; other data was in the form of detailed records, including rope construction and manufacturer, cutoff and resocketing periods, end-for-end switching, and downtime for rope change-out. Trends of average hoist rope life and average drag rope life determined from the field study are shown in [Fig. 1] as a function of bucket size. The three lines on the graph have slopes of 1, M, and 1/4. A comparison of the data shows that hoist ropes moved about twice as much material as drag ropes prior to retirement, although more than a two-to-one scatter within each category is evident. As expected, the larger machines with the larger buckets moved more total volume of material. The four pairs of solid symbols represent those data for which detailed rope life histories are presented in subsequent figures.

Jan 1, 1980