Search Documents

Executive DEGOLYER, Chairman SIDNEY H BALL RICHARD PETERS, JR WILLIAM H BASSETT J V W REYNDERS Finance GEORGE D BARRON, Chairman H A GUESS GEORGE OTIS SMITH Membership J M CALLOW, Chiarman FRANK L ESTEP WILBER JUDSON GEORGE D BARRON H N SPICER Alternates P A MOSMAN EDWARD B STURGIS

Jan 1, 1923

Executive HENRY A. BUEHLER, Chairman ERLE V. DAVELER EDGAR RICKARD JOHN M. LOVEJOY WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUMB, Chairman E. E. ELLIS PAUL D. MERICA H. G. MOULTON, Consultant Admissions RALPH M. ROOSEVELT, Chairman GEORGE D. BARRON DONALD M. LIDDELL WILBER JUDSONW. D. B. MOTTER, JR.

Jan 1, 1934

By L. C. Kern

This paper presents information on the use of a new propping agent (malleable aluminum particles) which has been used successfully for producing high-conductivity fractures. The conductivity of a packed fracture depends on the width of the fracture as well as the permeability of the propping material. It is significant that the flow capacity of a propped crack is often increased many fold by propping the crack with a sparse distribution of particles. However, the flow capacity of a sparsely propped crack can be limited by two phenomena: (I) crushing of the propping particles, and (2) embedment of the propping particles in the formation walls. Malleable aluminum particles exhibit interesting properties which tend to overcome these limitations. As high loads are applied to the particles they will deform slightly, rather than shattering. The deformation results in a greater bearing area against the formation wall. This reduces the stress on the particle and reduces particle penetration into the formation. The behavior of aluminum particles under load and the bearing capacities of serveral formation rocks have been measured in the laboratory. By properly using these data, as explained in this paper, the flow capacities of aluminum-propped cracks can be calculated for a variety of conditions. Aluminum particles have been used successfully in the field to prop fractures. Where high-conductivity fractures were needed, the aluminum-propped fractures have given greater well stimulation than could have been expected for conventional fracturing processes. INTRODUCTION The purpose of a hydraulic fracture treatment is to create a conductive channel from the wellbore out into the oil or gas formation. The word conductive is emphasized because we believe that the fracture conductivity (flow capacity) is one of the most important factors influencing fracturing results. Previous papers have pointed out the additional well stimulation that can sometimes be achieved by increasing fracture conductivity. Several years ago, we investigated in some detail the effect of fracture conductivity on productivity increases to be expeced from vertical fractures. Both electrical analog and theoretical studies of unsteady-state flow behavior were made. A discussion of the electrical analog equipment and some of the results of the study were given in a previous paper' by Dyes, Kemp and Caudle. Further details were given recently by McGuire and Sikora.5 Fig. 1 shows the remarkable influence of relative fracture flow capacity and length on well stimulation. Briefly, the study indicates the following. 1. High-permeability formations require high-conductivity cracks for best results. 2. The longer the crack, the higher the fracture conductivity required for best results. 3. If the conductivity of the crack is very large compared to the formation (i.e., flow is not being limited by crack conductivity), then the longer the fracture, the better will be the results. Judging from recently published articles,1,314 there is current interest in methods for obtaining high fracture conductivities. Hence, we would like to present in this paper a discussion of a new fracture propping process (use of aluminum particle) which we have used successfully to obtain highly conductive fractures. There are several factors which influence the conductivity of a propped crack. Conventional fracturing techniques frequently result in a crack completely packed with fracturing sand. For such conditions, the crack conductivity is the product of the width of the packed fracture and the permeability of the propping material. It is significant that a large increase in conductivity sometimes can be obtained by propping with particles which are distributed sparsely (less than a

US 4,134,944-Production of iron oxide ore pellets of uniform size and excellent strength. Small pieces of ore are rolled into nuclei in a first pellet-rolling circuit in the presence of a binder, the nuclei sized and hardened by sintering or cold-bonding of the binder, the nuclei rolled in additional ore to form product pellets, the pellets sized, the suitable size fraction taken as product, and undersize pellets returned to the rolling operation. P. A. Ilmoni and R. Drugge, assigned to Luossavaara-Kiirunavaara AB Jan 16, 1979. 5 pp. (264-37) Filed- 5-25-77 (800,278) Priority: Sweden, 6-2-76 (76/06,¬241). Same British 1,553,763, dated Oct 10, 1979. US 4,145,210-In the induration of pellets of iron oxide ore or iron works dust or sludge, a charge of dried pellets and 2-20% by weight of coke having a size range of from 5 to 30 mm, a drum index of more than 70, a reactivity index of less than 50, and a tumbler index of more than 50 is charged into a rotary kiln The charge is heated and passed through the rotating kiln to indurate the dried pellets without burning the coke Powder-coated coke is recovered from the kiln for reuse. Ring formation in the kiln is substantially prevented. K. Kato and K Kadota, assigned to Sumitomo Metal Industries, Ltd, and Sumitomo Heavy Industries, Ltd. Mar 20, 1979 10 pp (75-3) Filed- 2-22-77 (770,947) Priority: Japan, 2-24-76 (51/19,754) US 4,145,211-Method of cooling hot metallized iron oxide ore agglomerates from a direct reduction furnace Agglomer¬ates ranging from 3/a in to 41/2 in in cross-section and at a temperature of 1000-2000°F are formed into a moving bed while at rest relative to each other Air at ambient tempera¬ture is passed through the bed at a velocity sufficient to cool the agglomerates rapidly to a temperature no greater than about 500°F without substantial reoxidation of the metal in the agglomerates and by using air as the sole cooling gas. C A Czako, A Berzins, and M J Greaves, assigned to Arthur G McKee & Co Mar. 20, 1979 15 pp. (75-34) Filed: 7-18-77 (816,467)

Jan 1, 1980

By H. S. Drinker

THE first discovery of zinc 011 the property now worked by this company was made by the celebrated mineralogist, Prof. William Theodore Rapper, in 1845. Different claimants kept the property in continual litigation till 1861, when everything was satisfactorily settled by the purchase of the land by the company, who have worked it ever since. The mines are situated in a valley, four miles south of Bethlehem, Pa., in Lehigh County. The valley is from two to three miles broad, and is bounded 011 the north and south by syenitic hills. Syenite underlies the valley, and upon this is deposited the Potsdam sandstone, then a layer of slate, and, finally, a dolomitic limestone, belonging to the Chazy or Black River formation, in which the zinc deposits are inclosed. The rocks occur in folds, and have evidently been subjected to tremendous pressure from below, the zinc deposit being found in an anticlinal axis, in nearly vertical veins. I t is supposed that the zinc was originally disseminated through the

By George Smith

ChillaQoe is situated in latitude 17" S., about 138 miles from the port of Cairns, with which it is now connected by rail. A township has been established on the banks of Chillagoe creek, a perennial stream of irregular volume crossing the field almost at rightrangles, nearly midway between the mining-camps of Calcifer and Mungana, which have been formed at the southeastern and western extremes of the field respectively. This situation was selected because of the water-supply and its proximity to the site most suitable for the erection of reductionworks. By its central position it commands the whole of the mines. The altitude above sea-level is about 1200 ft., whereas that of Calcifer and Mungana is 1400 ft.—a difference sufficient to account for a materially higher temperature at Chillagoe. The surrounding limestone bluffis add by radiation to the heat, and, at the same time, prevent the cool breezes from passing freely through the town; consequently, the temper* ture, which is high throughout the year, and especially so during the summer months, is here ge~ierally very oppressive also. The general trend of the field is southeast and northwest, and its length about 18 miles, with an average width of 5 miles; the approximate area is thus 90 sq. miles. The surrounding mineral-district is, however, much more extensive, and numerous other mines, sprcad over wide areas and producing a variety of minerals, exist in the same or parallel belts of mineralized country, of which Chillagoe proper covers but a very small portion. Immense bluffs of limestone, wollastonite and conglomerate, rising in places to nearly 300 ft., and so~netimes nearly a quarter-mile across, give the field a very picturesque and interesting appearance. The limestone has been classified as Devo-

Jan 1, 1904

By Sidney Cornell

THE technical- advantages of adding oxygen to air and producer gas, or using it as a reactive agent, producing 400 B.t.u. gas instead of. the present 150 B.t.u., with higher flame temperatures and a reducing flame possible, with a smaller volume of gases passing through a furnace, will result in quicker melting, sharp working, and the production of a higher quality steel. Probably electric-furnace quality steel can be produced in an open-hearth furnace using oxygen. A modern, standard, 100-ton open-hearth furnace, with all equipment, costs from $350,000 to $500,000; there are about 1000 open-hearth furnaces in this country. When considering the use of oxygen in the open-hearth furnace, it is necessary to study: (1) The use of oxygen in the present furnaces, such that modification of existing furnaces and equipment cost the minimum, although the full advantages of oxygen are not thus obtainable. (2) The use of oxygen in a furnace designed for its use, producing quality and quantity steel at the lowest possible cost. This entails the junking of approximately one-half the value in existing equipment-writing off $250,000,000. The basis of such an estimate is the present cost of manufacturing open-hearth steel. Objection may be taken to some of the unit prices here given, but while some companies obtain their ores for much less, the prices quoted are -market price. They are used to show the maximum economy obtained by oxygen at that point.

Jan 11, 1924

By Thomas Read

PERSONNEL work is a term recently introduced to cover the great variety of activities in industrial work that deal with the human factor. Much attention has been focussed upon individual phases of personnel work, such as accident prevention, sanitation, "welfare" work, reducing labor' turnover, and so on. In most cases these activities have been carried on as though they were distinct and separate fields; as a matter of fact, they are only different phases of the single problem of human engineering, and each has important and fundamental relations with the others. Thus, for example, high labor turnover is one of the most .important causes of a high accident rate, and unsatisfactory housing conditions are an important cause of labor turnover. In the early stages of the study of these problems, it was necessary to take them up separately; the time has now arrived at which it is desirable to consider them as a whole in order to bring them into the right relation to each other. When thus considered as phases of an interrelated whole, they may be grouped as personnel work. A discussion of the importance of personnel work as a means of in creasing dividends in industry may be objected to by some as a too materialistic way of looking upon work that is humanitarian. Nothing could he more mistaken than such an opinion. Humanitarianism, per se, has no place in industry, and nothing is gained and much is lost in pre tending that it has. The only reason why a corporation engages in business is to make profits, and any activity of the corporation that does not tend either directly or indirectly toward that end is poor business. It is equally poor business to overlook any activities that do tend indirectly to the making of profits. On this basis, personnel work can be justified as a corporate activity; there is no justification whatever for abstract humanitarianism from the business standpoint. One characteristic of the American workman is a general high level of intelligence, and it is an insult to intelligence to ask a man to believe that anything so impersonal as a corporation is really desirous of benefiting

Jan 10, 1917

By Herbert Johnson

DURING the past 10 or 12 years very little information has been made generally available concerning the commercial possibilities of separating materials by means of static electricity; and yet during that same period important improvements have been made in various branches of the science of electricity, which, when taken together, and applied to electro-static separation, have resulted in important improvements in that art as well. For example, much improvement has been made in high-voltage electrical equipment such as full-wave vacuum-tube rectification and improved mechanical rectification. Great strides have likewise been made in the development of insulators for high-voltage work, not only in the materials used but also in the design of the insulators themselves. Again, in another field, the development of air-conditioning equipment has improved the technique of controlling the surface condition, through drying or humidifying, of the various materials that are passed through the electrostatic separator. In many authoritative publications and textbooks, the electrostatic separation process is declared to require a balance far too sensitive for general commercial application. For example, one publication1 in the past has referred to an unfavorable effect on the process caused by varying atmospheric conditions such as humidity. Some2 have even gone so far as to state that sunlight and shadows may seriously affect the separating efficiency of the process. Such statements may have been true in the early development of the art, when the source of static elec-tricity was derived from a friction disk machine, such as the Wimshurst. The Blake Mosher equipment and the work of Huff in applying motor-generator sets, transformers and mechanical rectification overcame much of this kind of objection to the commercial application of the elec-trostatic separating process.

Jan 1, 1938

By Charles L. Mantell, James E. Hoffmann

Mechanical inclusion, electrophoretic deposition, and adsorption were studied as mechanisms for code-position of aluminas present in copper-plating electrolytes as an insoluble disperse phase. Mechanical inclusion was not a significant factor. That codeposi-tzon of aluminas by an electrophoretic mechanism was unlikely was substantiated by measurements of the potential of the aluminas. The alumina content of the deposits was studied as a function of the pH of the bath. These tests in conjunction with sedimentation studies demonstrated the absence of an isoelectric point for the alutninas over the pH range examined. Thiourea in the electrolyte (a substance known to be adsorbed on a copper cathode during electrodeposition) affected the amount of alumina in the electrodeposit. However, no adsorption of thiourea on aluminas in aqueous dispersions was detected. If it were possible to produce a dispersion-hardened alloy of copper and alumina by electrodeposition, an alloy possessing both strength and high conductivity at elevated temperatures might be anticipated. Investigation of the mechanism of codeposition of aluminas with copper was undertaken with the hope that knowledge of the mechanism would aid in the development of such an alloy. The word "codeposit" here does not necessarily imply an electrolytic phenomenon but rather that the materials codepositing, the various aluminas, are transported to and embedded in the electrodeposited copper by some means. Mechanical inclusion in electrodeposition implies a mechanism of codeposition which is wholly mechanical in nature; the only forces acting on a particle are gravity and contact forces. Such a particle is presumed to be electrically inert and incapable of any electrical interaction with electrodes in an electrolytic plating bath. Processes for matrices containing a codeposited phase by electrodeposition from a bath containing a disperse insoluble phase frequently state that code-position is caused by mechanical inclusion.10,2,12 If settling, i.e., gravity, be the controlling mechanism for codeposition of aluminas, then assumptions may be made that 1) the content of alumina in the electrodeposit should be enhanced by increasing the particle size, 2) the geometry of the system, that is, the disposition of the cathode surfaces relative to the di- rection of the falling particles, should affect the alumina content of the electrodeposit, 3) in geometrically identical systems the chemical composition of the electrolyte employed should exercise no effect on the alumina content of the deposit, that is, the alumina content should be the same in all cathode deposits irrespective of bath composition. A bent cathode19 evaluates the clarity of filter effluent in electroplating baths by comparing the roughness of the deposit on the vertical surface with that on the horizontal surface. Two difficulties are inherent in this technique: 1) the current density on the horizontal portion of the cathode would be substantially greater than that on the vertical surface; 2) should the deposit obtained be rough, projections on the vertical face could act as horizontal planes and vitiate the relationship between the vertical and horizontal surfaces. Bath composition should have no substantial effect on the alumina content of the deposit. Two different electrolytic baths were employed. They possessed variant specific conductances and substantially different pH ranges. The experimental tanks were rectangular Pyrex battery jars 6 in. wide by 3 1/4 in. long by 9 3/4 in. deep. The cathodes were stainless steel 316 sheet of 0.030 in. thickness, cut to 7.5 by 1.75 in. and bent at right angles to form an L-shaped cathode whose horizontal surfaces measured 1.75 by 3.0 in. All edges and vertical surfaces were masked with Scotch Elec-troplaters Tape No. 470. The anodes were electrolytic cathode copper 9 in. high by 2.25 in. wide by 0.5 in. thick. To eliminate inordinately high current densities on the projecting edge of the cathode, the anode was masked 1 in. above and below the projected line of intersection of the cathode with the anode. The exposed area of the anode was equal to that of the cathode, providing both with equal average current densities. The agitator in the cell was of Pyrex glass and positioned so its center line was equidistant from cathode and anode, and a plane passed horizontally through the center of the blade would be located equidistant from the bottom of the cathode and the bottom of the deposition tank. The assembled apparatus is depicted in Fig. 1. Hatched areas on anode and cathode represent the area of the electrodes wrapped with electroplaters tape. MATERIALS The chemicals were copper sulfate—CuSO4 • 5H2O— technical powder (Fisher Scientific Co.). Spectro-graphic analysis showed substantial freedom from antimony, arsenic, and iron. Traces of nickel were present.

Jan 1, 1967

By G. W. Tracy, R. D. Carter

Numerical calculations were made to determine the behavior of reservoirs with high-pressure drawdown and wide well spacing where the initial productivity is low and the wells are completed by hydraulic fracturing. The two-phase flow equations were solved for the flow into a single well. This well was assumed to be producing from a reservoir with hydraulically created horizontal fractures (four different systems with fractures were studied). For comparison purposes, additional two-phase flow calculations were made assuming a reservoir with uniform rock properties. The two-phase flow results were also compared with the conventional calculation methods, which do not include the effect of saturation gradients resulting from a simultaneous flow of oil and gas which are normal to this type reservoir. It was found that the conventional methods predict (1) a high and too optimistic value of ultimate recovery, (2) a high producing rate and a high reservoir pressure at a given oil recovery and (3) a low trend of gas-oil ratio with oil recovery. Included in the two-phase flow calculations were provisions to control the oil production rate by an allowable rate and, also, by a gas-oil ratio penalty rule. For the systems with hydraulic fractures, the producing rate was controlled by the gas-oil ratio penalty rule for most of the life. This is in contrast to the system with uniform rock properties which went "on decline" almost immediately. An unexpected characteristic of the systems which included fractures was the early rise in producing gas-oil ratio from 730 cu ft/bbl to approximately 1,200 cu ft/bbl, followed by a "leveling off" before the normally expected gas-oil ratio rise began. Additional features which are a result of hydraulic fracturing are (I) greater ultimate recovery, (2) higher average producing rates and (3) a lower average reservoir pressure at a given oil recovery. INTRODUCTION Some oil fields discovered during the past few years are producing from certain volumetric ally controlled reservoirs (often referred to as solution or internal gas- drive reservoirs) which are characterized by high-pressure drawdown at the wells. Since the available pressure drawdown at a well is limited by the static reservoir pressure and the producing rate is controlled by the available drawdown, wells completed in this type of reservoir usually produce at a rate less than the allowable from the time of completion. Because of this, this type of reservoir is referred to as a low productivity reservoir. Economic considerations require the use of wide well spacing and well stimulation by hydraulic fracturing to make commercial wells in this type of reservoir. Performance predictions for volumetrically controlled reservoirs have been made using a combination of two standard equations. 1. The "Schilthuis" or "Muskat" type material balance equation is used to relate the average reservoir pressure and the cumulative oil recovery. 2. The results from the material balance equation and the productivity factor as described by Pirson' are used to relate the cumulative recovery with producing rate and time. The material balance equation assumed uniform pressure and liquid saturation conditions throughout a reservoir. The steady-state radial flow formula allows for a pressure gradient toward a well but assumes uniform liquid saturation. These calculation methods are adequate for application to reservoirs wherein the drawdown at the well to realize satisfactory producing rates is small compared to the total pressure. In low productivity, volumetrically controlled reservoirs, the pressure drawdown at the well is large cornpared to the total pressure. Although a precise number cannot be given for the magnitude of a large pressure drawdown, values in excess of 1,000 psi would definitely be included. For practical considerations, this usually occurs when the formation flow capacity is less than about 100 md-ft. However, this limit of formation flow capacity will vary with the well producing rate. The low pressure in the neighborhood of the well which results from a high drawdown causes evolution of large volumes of gas. This causes the gas saturation to be higher near the well than at a greater distance—-hence, a non-uniform gas saturation. Also, the relationship between the relative permeability to oil (K/K) and gas saturation is nonlinear but decreases approximately in an exponential way with increases in gas saturation. Because of this, the following chain reaction is established.

By M. L. Holzworth, Joseph C. Kremer, Paul A. Beck, L. J. Demer

FOR alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystallization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig r shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hrs. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b. It is seen that for any annealing temperature below T. the grain size was smaller than in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T. the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T, or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig 11 by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has has been most frequently and best investigated in brass. This type has been designated as "normal grain growth," while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1947

By J. W. Halley, G. L. Plimpton

BECAUSE of the two distinct stages in the solidification of rimmed steel, segregation in the rimmed ingot is more complex than that in the killed or semikilled ingot. In the earlier stage, chemical reactions, resulting in evolution of gas and vigorous stirring of the metal, effect a degree of negative segregation unique to rimmed steel. The composition of this zone constitutes the principal quality advantage of this type of steel. In the later stage of solidification, after the evolution of gas has ceased, the segregation follows the general pattern of a more completely deoxidized steel. However, the composition of the liquid remaining after the first solidification stage varies markedly from that of the original melt, some constituents having been partially removed as reaction products while the concentration of others has been intensified by rejection from the metal solidifying in the first zone. The aim, from the standpoint of segregation, in rimmed steel of high quality is to effect a maximum negative segregation in the rim zone without excessive concentration of undesirable elements at the center of the ingot. To achieve this aim, the composition of the melt may be varied and the furnace and pouring practice may be adjusted within certain limits. It is the purpose of this study to discuss segregation in rimmed steel from the standpoint of the mechanisms that produce it and to survey the phases of open-hearth practice that influence those mechanisms. MECHANISMS PRODUCING SEGREGATION The mechanisms that determine the degree of segregation in the rimmed ingot are closely interrelated, making it difficult to select the primary factors and to determine a satisfactory order for presenting them. For instance, the question of sulphur segregation is relatively simple, since sulphur is not directly involved in chemical reactions in the ingot; but its concentration in the rim zone is dependent not only on its original analysis in the melt, its segregation coefficient, and the freezing rate, but also on the rate of its removal from the impure film on the solidifying surface. This washing action involves all the factors (such as freezing rate, the carbon-oxygen product, pressure, etc.) that determine the rate of gas evolution and hence the efficiency of film removal. Sulphur distribution between the rim and core is affected by the volumetric ratio between the two zones, and its segregation in the core is a function not only of the freezing rate of the core but also of all the foregoing factors that determine its concentration in the metal when solidification of the core starts. To simplify the presentation, it is proposed to treat the mechanisms affecting segregation independently in this section, reserving a discussion of their over-all effects for the section in which actual segregation data are given. The factors affecting segregation will be treated in the following order: (I) differential solidification, (2) removal of constituents as

Jan 1, 1944

By D. V. Edmonds, C. J. Beevers

Tensile tests were carried out on a! titanium containing 850, 1250, and 2700 ppm 0, and up to -500 ppm H. The tests were performed at -196", -78", 20°, 150°, and 300°C at a strain rate of -1.0 x 10??3 sec-1. Increasing oxygen content, increasing grain size, and decreasing test temperature resulted in enhanced embrittlement of the a titanium by the hydrogen additions. Metallographic observations showed that this can be correlated with the influence of these parameters on the introduction of cracks into the a! titanium by fracture of titanium hydride precipitates. CRAIGHEAD et al.1 reported that the hydrogen content normally found in commercial-purity a! titanium (60 to 100 ppm) was sufficient to cause a substantial lowering of the impact strength, and they attributed this embrittling effect of hydrogen to the precipitation of titanium hydride. Lenning et al.&apos; found that in commercial-purity a titanium there is an almost complete loss of impact strength at about 200 pprn H, which is approximately half the value needed to eliminate the impact strength of high-purity a titanium. They also showed that the presence of 3000 ppm hydrogen reduces the room-temperature tensile ductility of commercial-purity material to a value of the order of 10 pct; the corresponding hydrogen concentration for high-purity titanium is over 9000 ppm. It thus appears that the detrimental effect of hydrogen on the mechanical properties of commercial-purity titanium becomes evident at much lower hydrogen contents than for high-purity titanium. The main difference between the two types of a titanium might be expected to be the higher level of interstitial impurity in the commercial-purity grade. Jaffee et a1.3 studied the influence of temperature and strain rate on the hydrogen embrittlement of high-purity and commercial-purity ! titanium. In general, the behavior was the same for both materials; embrittlement was enhanced by decreasing temperature and increasing strain rate. Recent results from tests on commercial-purity a titanium containing 850 ppm O and varying amounts of hydrogen up to -500 ppm showed that the degree of embrittlement by hydrogen is intimately related to the fracture characteristics of titanium hydride precipitates.4 The present paper considers the interrelationship between the mechanical properties and micro-structural features of commercial-purity a! titanium containing 850, 1250, and 2700 ppm 0 and varying amounts of hydrogen up to -500 ppm. 1. EXPERIMENTAL PROCEDURE Three types of commercial-purity titanium supplied by IMI* were used in the investigation, and for the *Address: Witton, Birmingham 6, United Kingdom. purpose of this paper are designated Ti 115, Ti 130, and Ti 160. The principal impurity elements are given in Table I. The material was received in the form of 12.7 mm diam bars having a fully recrystallized structure. Tensile specimens with a round cross-section of 4.5 mm diam and a gage length of 15.2 mm were machined from the bars. In order to develop the same grain size (mean linear intercept of grain boundaries) in each of the three types the specimens were annealed under a dynamic vacuum of <10?5 mm Hg, Table 11. Specimen hydriding was carried out in a modified Sieverts apparatus;&apos; hydrogen was taken into solution at 450°C and after holding the specimens at this temperature for 24 hr they were furnace-cooled to room temperature at an average rate of -100 C deg per hr. By this method nominal hydrogen contents of 0, 50, 100, 250, and 500 ppm were introduced into specimens of Ti 115, Ti 130, and Ti 160 (100 ppm (wt) -0.5 at. pct). The actual hydrogen contents were calculated from the weight differences obtained by weighing the specimens before and after the hydriding treatment. Tensile tests were carried out at temperatures of -196", -78", 20°, 150°, and 300°C on a 10,000 kg In-stron machine at a nominal strain rate of -1.0 x 10-3 sec-1. Fractured specimens were sectioned in planes parallel to the tensile axis, mechanically polished to 0.25 µm grade of diamond paste, and then attack polished using a solution containing by volume 99 parts H2O, 1 part HF, and 1 part HNO3. Although the latter treatment unavoidably opened out cracks and voids visible after mechanical polishing, it did reveal the grain structure, titanium hydride morphology, and deformation twinning structure.

Jan 1, 1970

By D. F. Stein

In spite of the apparent usefulness of autoradiography in demonstrating segregation, it has had very limited success in demonstrating grain boundary segregation. Because of this limited success, a model system amenable to mathematical analysis was devised to determine which variables in the experiment are most important. As a result of these calculations, it was concluded that autoradiograPhy is a rather insensitive technique to measure grain boundary segregation. The range (energies) of the emitted particles (ß and a) must be low, and the concentration of the radioactive speczes at the grain boundary must be (in general) two or three orders of magnitude greater than the concentration within the grain. Because of these very restricted conditions , the limited success of the technzque is not surprising. In spite of the apparent usefulness of autoradiography in demonstrating segregation, it has had very limited success in demonstrating grain boundary segregation. Sulfur segregation in iron1 and possibly polonium segregation in Pb-5 pct B1 2 alloys are the only autoradi-ography experiments that have demonstrated segregation to grain boundaries in metals without the formation of a second phase. Segregation to a boundary without the formation of a second phase is often called Gibbs&apos; absorption and is discussed by McLean in Chapter 5 of Ref. 10. There are several394 experiments showing grain boundary diffusion of a radioisotope, but this type experiment is not representative of equilibrium between the concentration of an element at a grain boundary and that in bulk, so it will not be discussed in this paper. In an attempt to determine if temper embrittle ment of low-alloy steels was associated with segregation of antimony to grain boundaries, a program to use auto-radiography (using Sb-125) was initiated. Even though other measurements strongly suggest that segregation is occurring during embrittlement, no evidence of grain boundary segregation was observed in the auto-radiography experiments. An attempt was also made to detect segregation of carbon (using C-14) to grain boundaries in iron during slow cooling. There is again strong indirect evidence7 that segregation occurs during such a treatment, but the autoradiography experiment gave no evidence of such segregation. Because of the failure of these experiments and the general lack of success by our metallographic unit in measuring grain boundary segregation using autoradi-ography, a model system amenable to mathematical analysis was devised to determine which variables in the experiment are most important. MODEL SYSTEM The model system is illustrated in Figs. 1 and 2. It is a semi-infinite bicrystal with a single grain boundary perpendicular to the top face. The width of the grain boundary, W, is defined as the region to which segregation has occurred and it is assumed that this region is of constant composition. The assumption of an infinite dimension is for mathematical reasons but the results of such an analysis (as will be demonstrated later) are valid for even very small specimens. It also is assumed that the measurement is not limited by means of detecting the radiation (photographic emulsions, counters, and so forth) but that the means of detecting radiation is linearly sensitive to the radiation and has infinite resolving power. The distance y is the perpendicular distance from the center of the grain boundary to the point at which the background radiation is measured and x is the integration variable. CALCULATION FOR BETA PARTICLES Two values of the intensity of radiation will be calculated, the intensity at the center of the grain boundary and the intensity far from the grain boundary. The radiation at the center of the grain boundary can be calculated in the following way. Assume a grain boundary of width W having a uniform concentration equal to Cgb + Cb where CGb is the excess concentration of the element under consideration at the grain boundary and Cb is the bulk concentration. The intensity of radiation, IgB, at the center of the grain boundary, is a consequence of the amount of radioactive material, decay rate, absorption, and geometrical factors which can be represented mathematically by the following expression:

Jan 1, 1968

By J. J. Thomas, J. H. Nead

This investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 1, 1922

By J. H. Nead, J. J. Thomas

This investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 1, 1922

By Leendert de Witte, Fred J. Radd

In many areas caring failures can be directly related to electrical currents observed in the casings. It is the thesis of this paper that the observed casing currents are mainly due to electrochemical potentials of the type in evidence on spontaneous potential curves of electrical logs. The general nature of these potentials are discussed and an equivalent circuit is given for current and potential distributions around open holes. The casing forms a short circuit to these potentials and tends to average the effects of local cells. The case of casing corrosion opposite the Dakota water sands in the salt-mud area of Kansas is discussed anil used us a qualitative, illustration of the relation between SP&apos;s and casing currents. A method of quantitative derivation of casing current distribution frorn electric log SP curves, using linear transform theory, is described and results are compared with a measured current profile. The effects of hydrogen over-potentials at the cathodic portions of the pipe are considered and some laboratory data are given in support of conclusions regarding the over-1.01tuge.s. INTRODUCTION To date an appreciable amount of work has been done on the measurement of oil well casing currents and on the correlation of the anodic portions of the current profiles with corrosive casing failures. Speculations on the origin of the casing currents have, however, remained rather vague; and although almost every plausible cause has been mentioned, there is to the writers&apos; knowledge no clear-cut expose&apos; on the details of the causes of the corrosive currents in the literature. A study of current surveys and casing failures in the N.W. Burnett field, Ellis County. Kan.. indicated the probability that concentration cell emf&apos;s between the Wellington salt section and the relatively fresh waters in the Dakota sands were a major cause of the corrosion currents. A more general concept evolved upon analysis of the severe corrosive conditions in the Pleistocene sands in the Ventura Avenue and San Miguelito fields in California. In this area no major variations in the salt content of the formation waters occur and yet large casing currents are observed. An explanation is found in the fact that the local spontaneous potentials which are set up due to concentration contrast between the drilling fluid and the connate water are short circuited when casing is set. The very conductive path through the casing increases the magnitude of the currents and has the tendency to average local sources over fairly large intervals. Current will flow between the sections that are predominently shaly and the sections that are mostly sandy. At the places where the current leaves the pipe, corrosive attack will occur. This same phenomenon will be present wherever unprotected pipe is set through sections that show large SP kicks on the electric logs over reasonably thick interval~. GENERAL- NATURE OF THE SPONTANEOUS POTENTIALS When a sequence of sedimentary rocks is penetrated by a drill hole filled with a mud which has a different salt concentration from that in the formation waters, various types of electrochemical potentials are established between the formations and different parts of the mud column. Opposite clean sand sections. a simple liquid-liquid junction potential will be observed; while opposite argillaccous formations, a membrane potential, often referred to as shale potential, will be established. The first quantitative analysis of these emf&apos;s in terms of liquid junction and membrane potentials is due to Wyllie.1

Jan 1, 1956

By D. O. Noel

IT is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise remov-ing one of the alloying constituents.

Jan 1, 1938

By Theodore Simons

The rapid and comparatively recent development of flotation has opened so fascinating a field for study and research that the older processes of gravity concentration no longer receive the attention they deserve. The early work of Munroel and Richards12 and the more recent contributions by Clevenger and Coe,3 Laist and Wiggin,4 Ammon,5 Bardwell,6 Crowfoot,&apos; and Hayden8 (to mention only some which have appeared in our own Transactions) and by Schu1z,9 have furnished so much data that to offer something new seems a difficult task. It is still possible, however, to present known facts from a different point of view, and, with this in mind, the writer has undertaken to express basic principles of gravity concentration in terms of simple mathematics and mechanics; the conclusions thus reached will be found to correspond, in general, with those obtained by experimental methods. Rittinger, in his classic Aufbereitungskunde (1867)) reached analogous conclusions by way of intricate higher mathematics, for which reason his interesting investigations have remained a sealed book to most of us. The writer hopes that a more elementary treatment of the subject, based in part on Rittinger&apos;s metheds, may arouse new interest in the study of basic principles.

Jan 1, 1923